SW7120703_CURRENT PERMIT_20120725

STORMWATER DIVISION CODING SHEET
POST -CONSTRUCTION PERMITS
PERMIT NO.
SW Zk 723
DOC TYPE
� CURRENT PERMIT
❑ APPROVED PLANS
❑ HISTORICAL FILE
DOC DATE
D7o��
YYYYMMDD

NCDENR
North Carolina Department of Environment and Natural Resources
Division of Water Quality
Beverly Eaves Perdue Charles Wakild, P.E. Dee Freeman
Governor Director Secretary
July 25, 2012
Mr. Henry D. Butts, Jr., Vice President
S.T. Wooten Corporation
PO Box 2408
Wilson, NC 27894-2408
Subject: Stormwater Permit No. SW7120703
S.T. Wooten Winton Asphalt Plant
High Density Commercial Wet Pond Project
Hertford County
Dear Mr. Butts:
The Washington Regional Office received a complete Stormwater Management Permit
Application for S.T. Wooten Winton Asphalt Plant project on July 17, 2012. Staff review of the
plans and specifications has determined that the project, as proposed, will comply with the
Stormwater Regulations set forth in Session Law 2008-211 and Title 15A NCAC 2H.1000. We
are forwarding Permit No. SW7120703 dated July 25, 2012, for the construction of the subject
project.
This permit shall be effective from the date.of issuance until July 25, 2020, and shall be subject
to the conditions and limitations as specified therein. Please pay special attention to the
Operation and Maintenance requirements in this permit. Failure to establish an adequate
system for operation and maintenance of the stormwater management system will result in
future compliance problems.
If any parts, requirements, or limitations contained in this permit are unacceptable, you have
the right to request an adjudicatory hearing upon written request within thirty (30) days
following receipt of this permit. This request must be in the form of a written petition,
conforming to Chapter 150E of the North Carolina General Statutes, and filed with the Office of
Administrative Hearings, 6714 Mail Service Center, Raleigh, NC 27699-6714, Unless such
demands are made this permit shall be final and binding.
If you have any questions, or need additional information concerning this matter, please
contact Samir Dumpor, or me at [phone].
Si cerely,
All Hodge
Regional Supervisor
Surface Water Protection Section
AH/ sd: K-\WQSISTORMWATERISDISW7120703
cc: Jon Meade, Bartlett Engineering and Surveying, PC (1906 Nash Street, Wilson,
NC 27893) &-rna l I
Hertford County Building Inspections
,Washington Regional Office
North Carolina Division of Water Quality Intemet: www.ncwaterguali!y.org
943 Washington Square Mall Phone: [phone] One
Washington, NC 27889 FAX ,252-946-9215 NorthCarol.ina
An Equal opportunitylAffrrmativeAction Employer —50%a Recycledlt0%Post ConsumerPaper ;Vaturalk

State Stormwater Management Systems
Permit No. SW7120703
STATE OF NORTH CAROLINA
DEPARTMENT OF ENVIRONMENT AND NATURAL RESOURCES
DIVISION OF WATER QUALITY
STATE STORMWATER MANAGEMENT PERMIT
HIGH DENSITY DEVELOPMENT
In accordance with the provisions of Article 21 of Chapter 143, General Statutes of
North Carolina as amended, and other applicable Laws, Rules, and Regulations
PERMISSION IS HEREBY GRANTED TO
S. T. Wooten Corporation
S. T. Wooten Winton Asphalt Plant
Hertford County
FOR THE
construction, operation and maintenance of one wet detention pond in compliance with
the provisions of Session Law 2008-211 and 15A NCAC 2H .1000 (hereafter referred to
as the "stormwater rules') and the approved stormwater management plans and
specifications and other supporting data as attached and on file with and approved by
the Division of Water Quality and considered a part of this permit.
This permit shall be effective from the date of issuance until July 25, 2020, and shall be
subject to the following specified conditions and limitations:
1. DESIGN STANDARDS
1. This permit is effective only with respect to the nature and volume of stormwater
described in the application and other supporting data.
2. This stormwater system has been approved for the management of stormwater
runoff as described in Section 1.7 of this permit. The stormwater control has been
designed to handle the runoff from 321,081 square feet of impervious area.
3. The tract will be limited to the amount of built -upon area indicated in Section 1. of
this permit, and per approved plans.
4. All stormwater collection and treatment systems must be located in either
dedicated common areas or recorded easements. The final plats for the project
will be recorded showing all such required easements, in accordance with the
approved plans.
5. The runoff from all built -upon area within the permitted drainage area of this
project must be directed into the permitted stormwater control system.
6. The built -upon areas associated with this project shall be located at least 50 feet
landward of all perennial and intermittent surface waters.
7. The following design criteria have been provided in the wet detention pond and
must be maintained at design condition:
Page 2 of 7

State Stormwater Management Systems
Permit No. SW7120703
a.
Drainage Area, ftz:
458,687
b.
Total Impervious Surfaces, ft2:
Storm,
321,081
C.
Design inches:
1.5
d.
Pond Depth - average, feet:
3.0
e.
TSS removal efficiency:
90%
f.
Permanent Pool Elevation, FMSL:
97.00
g.
Permanent Pool Surface Area required, ft2:
37,154
h.
Permanent Pool Surface Area, ft :
50,000
i.
Min. Volume required, ft :
38,988
j.
Permitted Storage Volume, ft .-
40,666
k.
Temporary Storage Elevation, FMSL:
97.75
I.
Controlling Orifice:
3.00" O pipe
m.
Permitted Forebay Volume, ft3:
28,112
n.
Receiving Stream/River Basin: UT to Chowan River/Chowan Basin
a.
Stream Index Number.
25
p.
Classification of Water Body:
"B; NSW'
II. SCHEDULE OF COMPLIANCE
1. The stormwater management system shall be constructed in its entirety,
vegetated and operational for its intended use prior to the construction of any
built -upon surface.
2. During construction, erosion shall be kept to a minimum and any eroded areas of
the system will be repaired immediately.
3. The permittee shall at all time provide the operation and maintenance necessary
to assure the permitted stormwater system functions at optimum efficiency. The
approved Operation and Maintenance Plan must be followed in its entirety and
maintenance must occur at the scheduled intervals including, but not limited to:
a. Semiannual scheduled inspections (every 6 months).
b. Sediment removal.
G. Mowing and re -vegetation of slopes and the vegetated filter strip.
d. Immediate repair of eroded areas.
e. Maintenance of all slopes in accordance with approved plans and
specifications.
f. Debris removal and unclogging of outlet structure, orifice device, level
spreader, filter strip, catch basins and piping.
g. Access to the outlet structure must be available at all times.
4. Records of maintenance activities must be kept for each permitted BMP. The
records will indicate the date, activity, name of person performing the work and
what actions were taken.
5. The permittee shall submit to the Division of Water Quality an annual summary
report of the maintenance inspection records for each BMP. The report shall
summarize the inspection dates, results of the inspections, and the maintenance
work performed at each inspection.
6. Access to the stormwater facilities shall be maintained via appropriate
easements at all times.
7. The facilities shall be constructed as shown on the approved plans. This permit
shall become void unless the facilities are constructed in accordance with the
conditions of this permit, the approved plans and specifications, and other
supporting data.
8. Upon completion of construction, prior to issuance of a Certificate of Occupancy,
Page 3 of 7

State Stormwater Management Systems
Permit No. SW7120703
and prior to operation of this permitted facility, a certification must be received
from an appropriate designer for the system installed certifying that the permitted
facility has been installed in accordance with this permit, the approved plans and
specifications, and other supporting documentation. Any deviations from the
approved plans and specifications must be noted on the Certification. A
modification may be required for those deviations.
9. If the stormwater system was used as an Erosion Control device, it must be
restored to design condition prior to operation as a stormwater treatment device,.
and prior to occupancy of the facility.
10. The permittee shall submit to the Director and shall have received approval for
revised plans, specifications, and calculations prior to construction, for any
modification to the approved plans, including, but not limited to, those listed
below:
a. Any revision to any item shown on the approved plans, including the
stormwater management measures, built -upon area, details, etc.
b. Project name change.
C. Transfer of ownership.
d. Redesign or addition to the approved amount of built -upon area or to the
drainage area.
e. Further subdivision, acquisition, lease or sale of all or part of the project
area. The project area is defined as all property owned by the permittee,
for which Sedimentation and Erosion Control Plan approval or a CAMA
Major permit was sought.
f. Filling in, altering, or piping of any vegetative conveyance shown on the
approved plan.
11. The Director may notify the permittee when the permitted site does not meet one
or more of the minimum requirements of the permit. Within the time frame
specified in the notice, the permittee shall submit a written time schedule to the
Director for modifying the site to meet minimum requirements. The permittee
shall provide copies of revised plans and certification in writing to the Director
that the changes have been made.
12. The permittee shall submit final site layout and grading plans for any permitted
future areas shown on the approved plans, prior to construction.
13. A copy of the approved plans and specifications shall be maintained on file by
the Permittee at all times.
III. GENERAL CONDITIONS
This permit is not transferable except after notice to and approval by the Director.
In the event of a change of ownership, or a name change, the permittee must
submit a completed Name/Ownership Change form, to the Division of Water
Quality, signed by both parties, and accompanied by supporting documentation
as listed on page 2 of the form. The project must be in good standing with the
Division. The approval of this request will be considered on its merits and may or
may not be approved.
2. The permittee is responsible for compliance with all permit conditions until such
time as the Division approves the transfer request.
3. Failure to abide by the conditions and limitations contained in this permit may
subject the Permittee to enforcement action by the Division of Water Quality, in
accordance with North Carolina General Statute 143-215.6A to 143-215.6C.
Page 4 of 7

State Stormwater Management Systems
Permit No. SW7120703
4. The issuance of this permit does not preclude the Permittee from complying with
any and all statutes, rules, regulations, or ordinances, which may be imposed by
other government agencies (local, state, and federal) having jurisdiction.
5. In the event that the facilities fail to perform satisfactorily, including the creation
of nuisance conditions, the Permittee shall take immediate corrective action,
including those as may be required by this Division, such as the construction of
additional or replacement stormwater management systems.
6. The permittee grants DENR Staff permission to enter the property during normal
business hours for the purpose of inspecting all components of the permitted
stormwater management facility.
7. The permit issued shall continue in force and effect until revoked or terminated.
The permit may be modified, revoked and reissued or terminated for cause. The
filing of a request for a permit modification, revocation and re -issuance or
termination does not stay any permit condition.
8. Unless specified elsewhere, permanent seeding requirements for the stormwater
control must follow the guidelines established in the North Carolina Erosion and
Sediment Control Planning and Design Manual.
9. Approved plans and specifications for this project are incorporated by reference
and are enforceable parts of the permit.
10. The issuance of this permit does not prohibit the Director from reopening and
modifying the permit, revoking and reissuing the permit, or terminating the permit
as allowed by the laws, rules and regulations contained in Session Law 2008-
211, Title 15A NCAC 2H.1000, and NCGS 143-215.1 et. al.
11. The permittee shall notify the Division of any name, ownership or mailing
address changes at least 30 days prior to making such changes.
12. This permit shall be effective from the date of issuance until July 25, 2020.
Application for permit renewal shall be submitted 180 days prior to the expiration
date of this permit and must be accompanied by the processing fee.
Permit issued this the 25th day of July, 2012.
NO TH CAROLINA ENVIRONMENTAL MANAGEMENT COMMISSION
L for
Uharlbs Wakild, P.., Director
Division of Water Quality
By Authority of the Environmental Management Commission
Stormwater Permit No. SW7120703
Page 5 of 7

State Stormwater Management Systems
Permit No. SW7120703
S.T. Wooten Winton Asphalt Plant
Stormwater Permit No. SW7120703
Hertford County
Designer's Certification
I, , as a duly registered in the
State of North Carolina, having been authorized to observe (periodically/ weekly/ full
time) the construction of the project,
(Project)
for (Project Owner) hereby state that, to the
best of my abilities, due care and diligence was used in the observation of the project
construction such that the construction was observed to be built within substantial
compliance and intent of the approved plans and specifications.
The checklist of items on page 2 of this form is included in the Certification.
Noted deviations from approved plans and specification:
Signature
Registration Number
Date
SEAT_
Page 6 of 7

State Stormwater Management Systems
Permit No. SW7120703
Certification Requirements:
.1. The drainage area to the system contains approximately the permitted
acreage.
2. The drainage area to the system contains no more than the permitted
amount of built -upon area.
3. All the built -upon area associated with the project is graded such that the
runoff drains to the system.
4. All roof drains are located such that the runoff is directed into the system.
5. The outlet/bypass structure elevations are per the approved plan.
6. The outlet structure is located per the approved plans.
7. Trash rack is provided on the outlet/bypass structure.
8. All slopes are grassed with permanent vegetation.
9. Vegetated slopes are no steeper than 3:1.
10. The inlets are located per the approved plans and do not cause short-
circuiting of the system.
11. The permitted amounts of surface area and/or volume have been
provided.
12. Required drawdown devices are correctly sized per the approved plans.
13. All required design depths are provided.
14. All required parts of the system are provided, such as a vegetated shelf,
and a forebay.
15. The required system dimensions are provided per the approved plans.
cc: NCDENR-DWQ Washington Regional Office
Hertford County Building Inspections
Page 7.of 7

DWQ USE ONLY
Date Received
goo- lqqFee Paid
Permit Number
JUL 17 201Z
J.rc�,n I4o00
Sul -1 1 zLO 70 3
Applicable Rules: ❑ Coastal SW - 1995 ❑ Coastal SW - 2008 ❑ Ph II - Post Construction
(select aM D R Non -Coastal SW- HQW/ORW Waters ❑ Universal Stormwater Management Plan
❑ Other WQ M nit Plan:
State of North Carolina Wa.ZC�
Department of Environment and Natural Resources
Division of Water Quality
STORMWATER MANAGEMENT PERMIT APPLICATION FORM
This form may he photocopied for use as an original
I. GENERAL INFORMATION
1. Project Name (subdivision, facility, or establishment name - should be consistent with project name on plans,
specifications, letters, operation and maintenance agreements, etc.):
S.T. Wooten Winton Asphalt Plant
2. Location of Project (street address):
Industrial Park Rd
City:Winton
Cou nty:Hertford
3. Directions to project (from nearest major intersection):
Zip:
Approximately 0.34 miles cast of the intersection of NC Hxvy 158 and Industrial Park Rd on the west side of
Industrial Park Rd
4. Latitude:36' 23' 31" N 1_ongitude:76° 56' 56" W of the main entrance to the project.
It. PERMIT INFORMATION:
1. a. Specify whether project is (check one): ®New ❑Modification
If this application is being submitted as the result of a modification to an existing permit, list the existing
permit number , its issue date (if known) , and the status of
construction: ®Not Started ❑Partially Completed* ❑ Completed* 'provide a designer's certification
2. Specify the type of project (check one):
❑Low Density ®High Density ❑Drains to an Offsite Stormwa ter System ❑Other
3. If this application is being submitted as the result of a previously returned application or a letter from DWQ
requesting a state Stormwater management permit application, list the stormwater project number, if
assigned, and the previous name of the project, if different than currently
proposed,
4. a. Additional Project Requirements (check applicable blanks; information on required state permits can be
obtained by contacting the Customer Service Center at 1-877-623-6748):
❑CAMA Major ®Sedimentation/Erosion Control: 11.2 ac of Disturbed Area
®NPDES Industrial Stormwater 0404/401 Permit: Proposed Impacts
b.If any of these permits have already been acquired please provide the Project Name, Project/Permit Number,
issue date and the type of each permit:
Form SWU-101 Version 07Jun2010 I'age I of 6

III. CONTACT INFORMATION
1. a. Print Applicant / Signing Official's name and title (specifically the developer, property owner, lessee,
designated government official, individual, etc. who owns the project):
Applicant/Organization:S.T. Wooten Corporation
Signing Official & Title: I-lenry D.-Butts, Jr. (Vice President)
b.Contact information for person listed in item I above:
Street Address:3801 Black Creek Rd
Ci ty: W i ]son State:NC Z i p:27893
Mailing Address (if applicable):P.O. Box 2408
City:Wilson State:NC Zip:27894-2408
Phone: (252 ) 291-5165 Fax: (252 ) 243-0901
E m a i l:bu tch©stwco rp.coni
c. Please check the appropriate box. The applicant listed above is:
❑ The property owner (Skip to Contact Information, item 3a)
® Lessee* (Attach a copy of the lease agreement and complete Contact Information, item 2a and 2b below)
❑ Purchaser* (Attach a copy of the pending sales agreement and complete Contact Information, item 2a and
2b below)
❑ Developer* (Complete Contact Information, item 2a and 2b below.)
2. a. Print Property Owner's name and title below, if you are the lessee, purchaser or developer. (This is the
person who owns the property that the project is located on):
Property Owner/Organization:Commercial Ready Mix Products Inc.
Signing Official & Title:Tim NeNysome
b.Contact information for person listed in item 2a above:
Street Add
City:Cofield State:NC Zip:
Mailing Address (if applicable):
City:
Phone: ( )
Email:
State: Zip:
Fax: ( }
3. a. (Optional) Print the name and title of another contact such as the project's construction supervisor or other
person who can answer questions about the project:
Other Contact Person/Organization:Butch Lawter
Signing Official &'fitle:Henry D. Butts, Jr. Vice President
b. Contact information for person listed in item 3a above:
Mailing Address:3801. Black Creek Rd
City:Wilson
Phone: (252 ) 291-5165
State:NC
Zip:27894
Fax: (252 ) 243-0901
Email:[e-mail]
Form SWU-101 Version 07.1un2010 Page 2 of 7

4. Local jurisdiction for building permits: Hertford Co.
Point of Contact: Phone
IV. PROJECT INFORMATION
1. In the space provided below, briefly summarize how the stormwater runoff will be treated.
Stormwater from will be conveyed by -sheet flow and swales to a wet detention basin for treatment before
2. a. If claiming vested rights, identify the supporting documents provided and the date they were approved:
❑ Approval of a Site Specific Development Plan or PUD Approval Date:
❑ Valid Building Permit Issued Date:
❑ Other: Date:
b.If claiming vested rights, identify the regulation(s) the project has been designed in accordance with:
❑ Coastal SW - 1995 ❑ Ph II - Post Construction
3. Storm water runoff from this project drains to the Chowan Diver basin.
4. Total Property Area:12.31
acres
5. Total Coastal Wetlands Area: 0 acres
6. Total Surface Water Area: 0 acres
Total Property Area (4) -Total Coastal Wetlands Area (5) - Total Surface Water Area (6) = Total Project
Area*:12.31 acres
+ Total project area shall be calculated to exclude thefollowing. the normal pool of impounded structures, the area
between the baulks of streams and rivers , the area below the Normal HI lr Water (NNW) litre or Mean High Water
(MHW) lisle, and coastal Toetlands landward from the NHW (or MHX litre. The resultant project area Is used to
calculate overall percent built (upon area (BUA). Nolu-coastal Wetlands landward of the NHW (or MHW) litre in ay
be included in the total project area.
8. Project percent of impervious area: (Total Impervious Area / Total Project Area) X 100 = 70.0
9. How many drainage areas does the project have?7 (For high density, count I fl)r each proposed engineered
stormwater BMP. For loco density and other projects, use 7 for the whole property area)
-10, Complete the following information for each drainage area identified in Project Information item 9. If there
are more than four drainage areas in the project, attach an additional sheet with the information for each area
provided in the same format as below.
Form SWU-101 Version 073un2010 Page 3 of 7

Basin Information
Drainage Area 1
Drainage Area _
Drainage Area _
Drainage Area _
Receiving Stream Name
UT to Chowan R
Stream Class
B,NSW
Stream Index Number *
25
Total Drainage Area (sf)
458,687
10. 3 A&
On -site Drainage Area (so
458,687
Off -site Drainage Area (so
0
Pro osed Inapervious Area** (sq
321,081
Im ervious Area** total
70.0
Impervious** Surface Area
Drainage Area 1
Drainage Area _
Drainage Area _
Drainage Area _
On -site Buildings/Lots (so
-1,800
On -site Streets (so
27,809
On -site Parking (so
4,314
On -site Sidewalks (so
0
Other on -site (so
225,735
Future (so
0
Off -site (SO
0
Existing BUA*** (so
61,423
Total (sf):
321,081
* Stream Class and Itidex Number can be determined at: lrtfl;.Aortal.nedetrr.org vebA4,q ps/esu/classi rcatiolrs
** I►tr lervious area is defined as the built upon area including, but not limited to, buildings, roads, parking areas,
si e7valks, gravel areas, etc.
*** Report only flint mnonnt of existing BUA flint will remain after development. Do not report any existing BUA that
is to be removed and which will be replaced by new BUA.
11. I -low was the off -site impervious area listed above determined? Provide documentation. NA
Projects in [anion County: Cnntacl DYYQ Central Office stcito check if1he project is located ii4thin a Threatened R-
Endangerecl Species watershed that may be subject to more stringent stormwaler requirenients as per NC11 C 0213.0600.
V. SUPPLEMENT AND O&M FORMS
The applicable state stormwater management permit supplement and operation and maintenance (O&M) forms
must be submitted for each BMP specified for this project. The latest versions of the forms can be downloaded
from http://portal.ncdenr.org/web/wq/ws/su/bmp-manual.
VI. SUBMITTAL REQUIREMENTS
Only complete application packages will be accepted and reviewed by the Division of Water Quality (DWQ).
A complete package includes all of the items Iisted below. A detailed application instruction sheet and BMP
checklists are available from http://portal.ncdenr.org/web/wq/ws/su/statesw/forms_docs. The complete
application package should be submitted to the appropriate DWQ Office. (The appropriate office may be
found by locating project on the interactive online map at http:/1portal.ncdenr.org/web/wq/ws/su/maps.)
Please indicate that the following required information have been provided by initialing in the space provided
for each item. All original documents MUST be signed and initialed in blue ink. Download the latest versions
for each submitted application package from http//portal.ncdenr.org/web/wc{/ws/su/statesw/forms does.
/ Init'lls
1. Original and one copy of the Stormwater Management Permit Application Form. v
2. Original and one copy of the signed and notarized Deed Restrictions & Protective Covenants
Form. (if required as per Part V11 below)
3. Original of the applicable Supplement Form(s) (sealed, signed and dated) and O&M
agreement(s) for each BMP.
4. Permit application processing fee of $505 payable to NCDENR. (For an Express review, refer to
http://www.envlielp.org/pages/onestopexpress.litml for information on the Express program
and the associated fees. Contact the appropriate regional office Express Permit Coordinator for
additional information and to schedule the required application meeting.)
Fonn SWU-101 Version 07Jun2010 Page 4 of 7

Ayl�
5. A detailed narrative (one to two pages) describing the stormwater treatment/managementfor ✓
the project. This is required in addition to the brief summary provided in the Project
Information, item 1. /
6. A USGS map identifying the site location. If the receiving stream is reported as class SA or the V
receiving stream drains to class SA waters within'/2 mile of the site boundary, include the
mile radius on the map. ✓
7. Sealed, signed and dated calculations.
8. Two sets of plans folded to 8.5" x 14" (sealed, signed, & dated), including:
a. Development/Project name.
b. Engineer and firm.
c. Location map with named streets and NCSR numbers.
d. Legend.
e. North arrow.
f. Scale. J
g. Revision number and dates.
h. Identify all surface waters on the plans by delineating the normal pool elevation of
impounded structures, the banks of streams and rivers, the MHW or NHW line of tidal
waters, and any coastal wetlands landward of the MHW or NHW lines.
• Delineate the vegetated buffer landward from the normal pool elevation of impounded
structures, the banks of streams or rivers, and the MHW (or NHW) o tidal waters.
i. Dimensioned property/project boundary with bearings & distances. /
j. Site Layout with all I3UA identified and dimensioned.
k. Existing contours, proposed contours, spot elevations, finished floor elevations.
I. Details of roads, drainage features, collection systems, and stormwater control measures.
m. Wetlands delineated, or a note on the plans that none exist. (Must be delineated by a It/
qualified person. Provide documentation of qualifications and identify the person who
made the determination on the plans. ✓
n. Existing drainage (including off -site), drainage easements, pipe sizes, runoff calculations.
o. Drainage areas delineated (included in the main set of plans, not as a separate document). J
p. Vegetated buffers (where required).
9. Copy of any applicable soils report with the associated SHWT elevations (Please identify
elevations in addition to depths) as well as a ►nap of the boring locations with the existing
elevations and boring logs. Include an 8.5 xl l copy of the NRCS County Soils map with the
project area clearly delineated. For projects with infiltration BMPs, the report should also
include the soil type, expected infiltration rate, and the method of determining the infiltration rate.
(Infiltration Devices submitted to WiRO: Schedule a site visit for DWQ to verify the SHWT prior
to submittal, [phone],)
10. A copy of the most current property deed. Deed book: 597,724 Page No: 269,155
11. For corporations and limited liability corporations (LLC): Provide documentation from the NC
Secretary of State or other official documentation, which supports the titles and positions held
by the persons listed in Contact Information, item la, 2a, and/or 3a per NCAC 21-1.1003(e). The /
corporation or LLC must be listed as an active corporation in good standing with the NC r
Secretary of State, otherwise the application will be returned.
http://www.secret,iry.state.nc.us/Corporations/CSearcli.aspx
VII. DEED RESTRICTIONS AND PROTECTIVE COVENANTS
For all subdivisions, outparcels, and future development, the appropriate property restrictions and protective
covenants are required to be recorded prior to the sale of any lot. If lot sizes vary significantly or the proposed
BUA allocations vary, a table fisting each lot number, lot size, and the allowable built -upon area must be provided
as an attachment to the completed and notarized deed restriction form. The appropriate deed restrictions and
protective covenants forms can be downloaded from
htt2://portal.ncdenr.org/web/­­wq/­­ws/su/statesw/­foriiis does. Download the latest versions for each submittal.
In the instances where the applicant is different than the property owner, it is the responsibility of the property
owner to sign the deed restrictions and protective covenants form while the applicant is responsible for ensuring
that the deed restrictions are recorded.
By the notarized signature(s) below, the permit holder(s) certify that the recorded property restrictions and
protective covenants for this project, if required, shall include all the items required in the permit and listed
on the forms available on the website, that the covenants will be binding on all parties and persons claiming
under them, that they will run with the land, that the required covenants cannot be changed or deleted
without concurrence from the NC DWQ, and that they will be recorded prior to the sale of any lot.
Form SWU-101 Version 07Jun2010 Page 5 of 7

VHL CONSULTANT INFORMATION AND AUTHORIZATION
Applicant: Complete this section if you wish to designate authority to another individual and/or firm (such as a
consulting engineer and/or firm) so that they may provide information on your behalf for this project (such as
addressing requests for additional information).
Consulting Engineer:19n Meade
Consulting Firm: Barlielt.F.ngineering and Surveying, PC
Mailing Address:1906 Nash St
City -Wilson State:NC Zip:27893
Phone: 2 2 3- 7 Fax: [phone]
Emad:[e-mail]
IX. PROPERTY OWNER AUTHORIZATION (f Contact Information, item 2 has beenfilled out, complete this
section)
1, (print or type name of person listed in Contact Information, item 2a) Tim Newsome certify that I
own the property identified in this permit application, and thus give permission to (print or type name of person
listed in Contact Information, item Ia) Hen D. Butts Jr.VP with (print or type name of organization listed in
Contact Information, item In) S.T. Wooten Corp. to develop the project as currently proposed. A copy of
the lease agreement or pending property sales contract has been provided with the submittal, which indicates the
party responsible for the operation and maintenance of the stormwater system.
As the legal property owner I acknowledge, understand, and agree by my signature below, that if my designated
agent (entity listed in Contact Information, item 1) dissolves their company and/or cancels or defaults on their
lease agreement, or pending sale, responsibility for compliance with the DWQ Stormwater permit reverts back to
me, the property owner. As the property owner, it is my responsibility to notify DWQ immediately and submit a
completed Name/Ownership Change Form within 30 days; otherwise I will be operating a stormwater treatment
facility without a valid permit. I understand that the operation of a stormwater treatment facility without a valid
permit is a vi9JatiQn of NC Genera Statue 143-215.1 and may result in appropriate enforcement action including
the assessment of ci il penalties,oqup to $25,000 per day, pursuant to NCGS 143-215.6.
Date:�1//)—
i, _hf? LU S TK/I , a Not Public for the State of ��>`� C�+.q��y� County of
� r
do hereby certify that _ /f%twS�^W� personally appeared
before me this- day of rliar o Z and ac le the a execu ' iif_ihe application for
a stormwater permit. Witness my hand
and official seal,
SEAL
My commission expires Sk L,�-ol�,
Form SWU-101 Version 07Jun2010
Page 6 of 7

X. APPLICANT'S CERTIFICATION
I, (print or type name of person fisted in Contact Information, item in) 1-Iexrrl D. Butts, Jr. (Vice President)
certify that the information included on this permit application form is, to the best of niy knowledge, correct and
that the project will be constructed in conformance with the approved plans, that the required deed restrictions
and protective covenan will be recorded, and that the proposed project complies with the requirements of the
applicable stor under 15A NCAC 2I-1 .1000, SL 2006-246 (Ph. II -Post Construction) or SL 2008-211.
Signature: i Date: gJ01(ZL
I, CA&Ahe _ t�PS —,a Notary Public for the State of eavekirQ_ , County of
do hereby certify that personally appeared
before me this ls�day of and acknowledge the due execution of the application for
a stormwater permit. Witness my hand and official seal,
SEA]_
My commission expires 06 . Ja' v')U tie
Form SWU-101 Version 07Jun2010 Page 7 of 7

EXPRESS
Permit Number: SVJ'l 1 % 0-70 -j
(to he pro vieled by D6l'Q)
Drainage Area Number:
JUL 17 20Wet Detention Basin Operation and Maintenance Agreement
NC ®ENR
I will keep a maintenance record on this BMP. This maintenance record will be kept in a
log in a known set location. Any deficient BMP elements noted in the inspection will be
corrected, repaired or replaced immediately. These deficiencies can affect the integrity
of structures, safety of the public, and the removal efficiency of the BMP.
The wet detention basin system is defined as the wet detention basin,
pretreatment including forebays and the vegetated filter if one is provided.
This system (check one):
❑ does ® does not incorporate a vegetated filter at the outlet.
This system (check one):
❑ does ❑ does not incorporate pretreatment other than a forebay.
Important maintenance procedures:
— Immediately after the wet detention basin is established, the plants on the
vegetated shelf and perimeter of the basin should be watered twice weekly if
needed, until the plants become established (commonly six weeks).
— No portion of the wet detention pond should be fertilized after the first initial
fertilization that is required to establish the plants on the vegetated shelf.
— Stable groundcover should be maintained in the drainage area to reduce the
sediment Ioad to the wet detention basin.
— If the basin must be drained for an emergency or to perform maintenance, the
flushing of sediment through the emergency drain should be minimized to the
maximum extent practical.
— Once a year, a dam safety expert should inspect the embankment.
After the wet detention pond is established, it should be inspected once a month and
within 24 hours after every storm event greater than 1.0 inches (or 1.5 inches if in a
Coastal County). Records of operation and maintenance should be kept in a known set
location and must be available upon request.
Inspection activities shall be performed as follows. Any problems that are found shall
be repaired immediately.
BMP element:
Potential problem.
How I will remediate theproblem:
The entire BMP
Trash/debris is resent.
Remove the trash/debris.
The perimeter of the wet
Areas of bare soil and/or
Regrade the soil if necessary to
detention basin
erosive gullies have formed.
remove the gully, and then plant a
ground cover and water until it is
established. Provide lime and a
one-time fertilizer application.
Vegetation is too short or too
Maintain vegetation at a height of
long.
approximately six inches.
Form SW401-Wet Detention Basin O&M-Rev.4 Page 1 oF4

Permit Number:
(!o he pro7'ided by DIVQ)
Drainage Area Number:
BMP element:
Potentialproblem:
How I will remediate theproblem:
The inlet device: pipe or
The pipe is clogged.
Unclog the pipe. Dispose of the
swale
sediment off -site.
The pipe is cracked or
Replace the pipe.
otherwise damaged.
Erosion is occurring in the
Regrade the swale if necessary to
swale.
smooth it over and provide erosion
control devices such as reinforced
turf matting or riprap to avoid
future problems with erosion.
The forebay
Sediment has accumulated to
Search for the source of the
it depth greater than the
sediment and remedy the problem if
original design depth for
possible. Remove the sediment and
sediment storage.
dispose of it in a location where it
will not cause impacts to streams or
the BMP.
Erosion has occurred.
Provide additional erosion
protection such as reinforced turf
matting or riprap if needed to
prevent future erosion roblems.
Weeds are present.
Remove the weeds, preferably by
hand. If pesticide is used, wipe it on
the plants rather than spraying.
The vegetated shelf
Best professional practices
Prune according to best professional
show that pruning is needed
practices
to maintain optimal plant
health.
Plants are dead, diseased or
Determine the source of the
dying.
problem: soils, hydrology, disease,
etc. Remedy the problem and
replace plants. Provide a one-time
fertilizer application to establish the
ground cover if a soil test indicates
it is necessary.
Weeds are present.
Remove the weeds, preferably by
hand. if pesticide is used, wipe it on
the plants rather than spraying.
The main treatment area
Sediment has accumulated to
Search for the source of the
a depth greater than the
sediment and remedy the problem if
original design sediment
possible. Remove the sediment and
storage depth.
dispose of it in a location where it
will not cause impacts to streams or
the BMP.
Algal growth covers over
Consult a professional to remove
50% of the area.
and control the algal growth,
Cattails, phragmites or other
Remove the plants by wiping them
invasive plants cover 50% of
with pesticide (do not spray).
the basin surface.
Form SW401-Wet Detention Basin O&M-Rev.4 Page 2 of. 4

Permit Number:
(to he provi(kd hY D0,Q)
Drainage Area Number:
BMP element:
Potentialproblem:
How I will remediate theproblem:
The embankment
Shrubs have started to grow
Remove shrubs immediately.
on the embankment.
Evidence of muskrat or
Use traps to remove muskrats and
beaver activity is present.
consult a professional to remove
beavers.
A tree has started to grow on
Consult a dam safety specialist to
the embankment.
remove the tree.
An annual inspection by an
Make all needed repairs.
appropriate professional
shows that the embankment
needs repair. if applicable)
The outlet device
Clogging has occurred.
Clean out the outlet device. Dispose
of the sediment off -site.
The outlet device is damaged
or replace the outlet device.
The receiving water
]-rosion or other signs of
-Repair
Contact the local NC Division of
damage have occurred at the
Water Quality Regional Office, or
outlet.
the 401 Oversight Unit at 919-733-
1786.
The measuring device used to determine the sediment elevation shall be such
that it will give an accurate depth reading and not readily penetrate into
accumulated sediments.
When the permanent pool depth reads 3.5 feet in the main pond, the sediment
shall be removed.
When the permanent pool depth reads 3.5 feet in the forebay, the sediment
shall be removed.
Sediment Removal
Bottom Elevat
93.5 ]
-----------------
192.5 t
FOREBAY
BASIN DIAGRAM
(fill in the blank.~)
IVolume'
ft Min.
Sediment
Storage
Permanent Pool Elevation 97
Pool
Sediment Removal Elevation 93.5 Volume
`-------------------------------------------- -----
Bottom Elevation
MAIN POND
l -ft n.
Sediment
Storage
Form SW401-Wet Detention Basin O&M-Rev.4 Page 3 of 4

Permit Number:
(to be provided by DIVQ)
I acknowledge and agree by my signature below that I am responsible for the
performance ofthe maintenance procedures listed above. I agree to notify DWQ of any
problems with the system or prior to any changes to the system or responsible party.
Project name:STW-Winton Asphalt Plant
BMP drainage area number: I
Print name: 1-Ienry D. Butts. Jr.
Title: Vice President S.T. Wooten Corp.
Address:P.O. Box 2408 Wilson, NC 27894-2408
Phone:[phone] / ZZ {/ f
Signature:
Date:
Note: The legally responsible party should not be a homeowners association unless more than 50% of
the lots have been sold and a resident of the subdivision has been named the president.
1 be, a Notary Public for the State of
County of do hereby certify that
personally appeared before me this l3``
day of cio i,, and acknowledge the due execution of the
forgoing wet detention basin maintenance requirements. Witness my hand and official
SEAL
My commission expires
9(_• :Jo • n)clC,
Form SW401-Wet Detention Basin O&M-Rev.4
Page 4of4

WET DETENTION POND ANALYSIS - ALL RULES
FILE NAME: S:IWQSISTORMWATERIEXCELSPREADSHEETSIPOND1120703
PROJECTM SW7 120703
REVIEWER: SD
Initial Run Date ????
PROJECT NAME: S.T. Wooten Winton Asphalt Plant
Last modified 25-Jul-12
Receiving Stream: UT to Chowan River
Class: B NSW
Drainage Basin: Chowan
Within 1/2 mile SrNY
or N
Index No. 25.00
Site Area
17.43
acres
(DDrainage Area
square feet
DA Area
10.53 acres
458687.00
Rules- "2008" or "Ph2"
2008
IMPERVIOUS AREAS - BUA
Runoff_ C
Buildings square feet
1
user input rec
Street square feet
0.98
formula
SW square feet
0.95
Future square feet
Offsite square feet
??
Other square feet
_ _
BUA at dill. DS3 square feet
TOTAL 321081.00 square feet
SURFACE AREA CALCULATION (with added DA and BUA at different design stor:n)
Overall % Impervious 70.00%
SAIDA Ratio
8.10%
Average Design Depth 3 feet
Req. SA
37154 sf
TSS, 85 or 90: 90 %
Prov. SA
50000 sf
TEMPORARY POOL AND FOREBAY VOLUME CALCULATIONS
New BUA
Old BUA
Drainage Area® 458687.00
0
sf
BUA 321081.00
0.00
sf
Post development Rv= 0.680
#DIV/0+
unitless
Old BUA Design Storm
inches
Old BUA Design Volume
0
1.5" New BUA Design Storm Volume 38988
1 yr. 24 hour precipitation depth (inches) 3.00
from NOAA chart
Predevelopment Rv value 0.05
Use 0.05 if no existing BUA
1 yr. 24 hr. Pre -development volume 5734
cubic feet
1 yr. 24 hr. Post -development volume r7A977
cubic feet
2008 Design Volume 38988 cubic feet
Phase 2 Design Volume 38988 cubic feet
Required Volume 38988 cf
Area, sf
Inc. volume Acc. volume
Top of Sediment 93.50 msl ........
26064.00
0.00 0.00
Bottom of Shelf 96.50 msl.........
44100.00
105246.00 105246.00
Permanent Pool 97.00 msl.........
50000.00
23525.00 128771.00
Top of Shelf 97.50 msl.........
56250.00
26562.50 155333.50
Temporary Pool 97.75 msl.........
57032.00
14160.25 169493,75
Volume met at elev 99.07 msi
FOREBAY
Vol. Prov. at TP 40722.75 cf
Perm. Pool Volume= 128771
Req. Forebay Volume= 25754
Provided Volume=
Z$ i 2
Percent=
-D.644r•
21 g
Calculated Average Depth, feet = 12.86
Max Pump HP 1/2
ORIFICE CALCULATtC
Average Head
Flow Q2, cfs
Flow Q5, cfs
No. of Orifices
Diameter, inches
Drawdown =
1 yr 24 hr intensity, in/hr
Runoff Coefficient
1 yr 24 hr peak Q
Orifice flow<i yr24hr ?
feet Q2 Area =
14.78
sq. inches
cfs Q5 Area =
5.91
sq. inches
cfs Orifice Area =
7.07
sq. inches
Avq. Flow Q=
0.108
cfs
or weir H x I in x
lays # of end contractions, N =
40AA chart discharge coefficient, C = 3.30
initless Effective weir length, L = 0.00
in