HomeMy WebLinkAbout20051563 Ver 1_Complete File_200508120? W A T ?RQG
? r
Michael F. Easley, Governor
Willian G. Ross Jr., Secretary
North Carolina Department of Environment vid Natural Resources
Alan W. Klimek, P.E. Director
Division of Water Quality
August 22, 2005
Jon Creighton
Buncombe County Government
205 College Street
Asheville, NC 28801
Subject Property: Dillingham Creek - EWP (DSR 2005 - 45)
DWQ Project # 05-1563
Buncombe County
Qr? @FodF P
AUG 3 1 2005
DENR - WATER QUALITY
Vr1 W40S AND STORMWATER BRANCH
Approval of 401 Water Quality Certification with Additional Conditions
Dear Mr. Creighton:
You have our approval, in accordance with the attached conditions and those listed
below, to place fill within or otherwise impact 200 linear feet of streams for the purpose
of streambank stabilization at the subject properties, as described within your
application received by the N.C. Division of Water Quality (DWQ) on August 12, 2005.
After reviewing your application, we have decided that the impacts are covered by
General Water Quality Certification Number(s) 3376 (3376). The Certification(s) allows
you to use Nationwide Permit(s) 37 when issued by the US Army Corps of Engineers
(USACE). In addition, you should obtain or otherwise comply with any other required
federal, state or local permits before you go ahead with your project including (but not
limited to) Erosion and Sediment Control, Non-discharge, and stormwater regulations.
Also, this approval to proceed with your proposed impacts or to conduct impacts
to waters as depicted in your application shall expire upon expiration of the 404
or CAMA Permit.
This approval is for the purpose that you described in your application. As "stable" and
"pre-storm" are not interchangeable terms, all work must be to ensure stability,
regardless of channel location. Additionally, channels cannot be returned to it's pre-
storm location unless there is documented instability is submitted and approved as part
of the application package. If you change your project beyond the activities authorized
below, you must notify us and you may be required to send us a new application. If the
property is sold, the new owner must be given a copy of this Certification and approval
letter and is thereby responsible for complying with all conditions. If total fills for this
project (now or in the future) exceed one acre of wetland or 150 linear feet of stream,
compensatory mitigation may be required as described in 15A NCAC 2H .0506 (h).
This approval requires you to follow the conditions listed in the attached certification and
any additional conditions listed below.
The Additional Conditions of the Certification are:
901 Wetlands Certification Unit
1650 Mail Service Center, Raleigh, North Carolina 27699-1650
2321 Crabtree Boulevard, Suite 250, Raleigh, North Carolina 27604
Phone: 919-733-1786 /FAX 919-733-6893 / Internet http://h2o.enr.state.nc.us/ncvvetlanos
NcoirethCarolina
,iValumlly
An Equal Opportunity/Affirmative Action Employer- 50% Recyc!ed/10% Post Consumer Paper
Buncombe County:
Page 2 of 6
August 22, 2005
1. Impacts Approved
The following impacts are hereby approved as long as all of the other specific
and general conditions of this Certification (or Isolated Wetland Permit) are met.
No other impacts are approved including incidental impacts:
Amount
Approved (Units) Plan Location or Reference
Stream 200 (feet) Bi Iv Creek
2. Erosion & Sediment Control Practices
Erosion and sediment control practices must be in full compliance with all
specifications governing the proper design, installation and operation and
maintenance of such Best Management Practices in order to protect surface
waters standards:
a. The erosion and sediment control measures for the project must be
designed, installed, operated, and maintained in accordance with the most
recent version of the North Carolina Sediment and Erosion Control Planning
and Design Manual.
b. The design, installation, operation, and maintenance of the sediment and
erosion control measures must be such that they equal, or exceed, the
requirements specified in the most recent version of the North Carolina
Sediment and Erosion Control Manual. The devices shall be maintained on
all construction sites, borrow sites, and waste pile (spoil) projects, including
contractor-owned or leased borrow pits associated with the project.
c. For borrow pit sites, the erosion and sediment control measures must be
designed, installed, operated, and maintained in accordance with the most
recent version of the North Carolina Surface Mining Manual.
d. The reclamation measures and implementation must comply with the
reclamation in accordance with the requirements of the Sedimentation
Pollution Control Act.
3. No Waste, Spoil, Solids, or Fill of Any Kind
No waste, spoil, solids, or fill of any kind shall occur in wetlands, waters, or riparian
areas beyond the footprint of the impacts depicted in the Pre-Construction
Notification. All construction activities, including the design, installation, operation,
and maintenance of sediment and erosion control Best Management Practices,
shall be performed so that no violations of state water quality standards, statutes,
or rules occur.
Buncombe County:
Page 3 of 6
August 22, 2005
4. No Sediment & Erosion Control Measures w/n Wetlands or Waters
Sediment and erosion control measures shall not be placed in wetlands or waters
to the maximum extent practicable. If placement of sediment and erosion control
devices in wetlands and waters is unavoidable, they shall be removed and the
natural grade restored within six months of the date that the Division of Land
Resources has released the project.
5. Certificate of Completion
Upon completion of all work approved within the 401 Water Quality Certification
or applicable Buffer Rules, and any subsequent modifications, the applicant is
required to return the attached certificate of completion to the 401/Wetlands Unit,
North Carolina Division of Water Quality, 1650 Mail Service Center, Raleigh, NC,
27699-1650.
6. Sediment and erosion control measures must be implemented prior to construction
and maintained on the sites to minimize sediment in downstream areas. Seeding for
a temporary cover of wheat, millet, or similar annual grain or permanent herbaceous
cover should occur on all bare soil within five (5) days of ground disturbing activities
to provide long-term erosion control. The projects should be accomplished in stages
instead of leaving large tracts exposed to further storm events. Erosion control
matting should be used in conjunction with appropriate seeding on disturbed soils in
steep slope and riparian areas, unless authorized under Division of Land Resources
Erosion and Sediment Control approval. Matting should be secured in place with
staples, stakes, or, wherever possible, live stakes of native trees. Straw mulch and
tall fescue should not be used in riparian areas. In addition, because of an
anticipated difficulty in establishing ground cover during the winter, reseeding should
be conducted, as necessary, in the spring-time with a native annual and perennial
seed mix with a temporary nursery crop of wheat, millet or other grain.
7. Only clean, large, angular rock, large woody material, or other natural stream design
materials and techniques should be used for bank stabilization. Rock should not be
placed in the stream channel in a manner that constricts stream flow or that will
impede aquatic life movements during low flow conditions. Filter cloth should be
placed behind large rock that is used for bank stabilization. Properly designed rock
vanes should be constructed wherever appropriate on bank stabilization and
channel realignment stream reaches to improve channel stability and to improve
aquatic habitat. Root wads should be installed low enough in the bank so that a
significant portion (at least one-third) the root wad is inundated during normal flows.
8. The channel must be restored to a more stable condition. However, under no
circumstances should river rock, sand or other materials be dredged (excavated)
from the stream channel under authorization of this permit except, if necessary, in
the immediate vicinity of the eroding banks for the explicit purpose of anchoring
stabilizing or flow/grade control structures or for re-establishing the natural and more
stable stream channel dimensions. Streambed materials are unstable in flowing-
Buncombe County:
Page 4 of 6
August 22, 2005
water situations and are unsuitable for bank stabilization. Stream dredging has
catastrophic effects on aquatic life and disturbance of the natural form of the stream
channel can cause downstream erosion problems. The natural dimension, pattern,
and profile of the stream upstream and downstream of the permitted area should not
be modified by widening the stream channel or changing its depth.
9. Stabilization measures should only be applied on or near existing erosion sites,
leaving other stable stream bank areas in a natural condition. Grading and
backfilling should be minimized and tree and shrub growth should be retained where
possible to ensure long term availability of stream bank cover for aquatic life and
wildlife. Backfill materials should be obtained from upland sites except in cases
where excess stream bed materials are available. Berms are not permitted because
they block the floodplain, constrict and accelerate flood flows, and often fail or
impede drainage during large flood events.
10. Repairs to eroded banks should be conducted in a dry work area where possible.
Sandbags or other clean diversion structures should be used where possible to
minimize excavation in flowing water. Channel realignments should be constructed
by excavating the new channel from downstream to upstream before connecting it to
the old channel.
11. Heavy equipment should be operated from the bank whenever possible. All
mechanized equipment operated near surface waters should be inspected and
maintained regularly to prevent contamination of stream waters from fuels,
lubricants, hydraulic fluids or other toxic materials. Equipment used in stream
channel must be clean, new or low hour equipment.
12. Riparian Zone Replanting
Replanting of vegetation within disturbed areas located within 25 feet of the
streambank associated with any land disturbing activity, repair, replacement
and/or maintenance must be done in a manner consistant with the Guidelines
for Riparian Buffer Restoration immediately following construction. (Please
see attached.)Guidelines for Riparian Buffer Restoration.
(http://h2o.enr.state.nc.us/wrp/pdf/buffers.pdf )
13. Monitoring
The Permittee shall examine the stabilization work done under this Certification
on an annual basis for three (3) years following the completion of the restoration
efforts. This field evaluation should note the condition and stability of the
measures installed and how well the repair is holding up. A written report must
be provided to DWQ's Asheville Regional Office by June 1St of each year. The
report must describe inspection results, include digital photographs, list the date
of inspection, and describe any needed repairs or corrections.
13.The permittee will provide on-site supervision of stability work including, but not
limited to bank re-sloping, in-stream structure placement, and riparian zone re-
establishment, by an appropriately trained individual.
14. If pasture along the stream is to be used for grazing, the permittee must inform the
appropriate landowners that cattle should be prohibited from damaging riparian
areas and from de-stabilizing the stream banks and channel.
Buncombe County:
Page 5 of 6
August 22, 2005
15. Diffuse Flow
All constructed stormwater conveyance outlets shall be directed and maintained
as diffuse flow at non-erosive velocities through the protected riparian zones
such that it will not re-concentrate before discharging into a stream.
16. Water Quality Certification Notifications
The permittee must provide a copy of this issued Water Quality Certification and
attached cover letter to each property owner where the approved work will be
performed.
18.Turbidity Standard
The turbidity standard of 10 NTUs (Nephelometric Turbidity Units) shall not be
exceeded as described in 15 A NCAC 2B. .0200. Appropriate sediment and
erosion control practices must be used to meet this standard.
Violations of any condition herein set forth may result in revocation of this Certification
and may result in criminal and/or civil penalties. The authorization to proceed with your
proposed impacts or to conduct impacts to waters as depicted in your application and
as authorized by this Certification, shall expire upon expiration of the 404 or CAMA
Permit.
If you do not accept any of the conditions of this Certification (associated with the
approved wetland or stream impacts), you may ask for an adjudicatory hearing. You
must act within 60 days of the date that you receive this letter. To ask for a hearing,
send a written petition, which conforms to Chapter 150B of the North Carolina General
Statutes to the Office of Administrative Hearings, 6714 Mail Service Center, Raleigh,
N.C. 27699-6714. This certification and its conditions are final and binding unless you
ask for a hearing.
Buncombe County:
Page 6 of 6
August 22, 2005
This letter completes the review of the Division of Water Quality under Section 401 of
the Clean Water Act. If you have any questions, please telephone Cyndi Karoly in the
Central Office in Raleigh at 919-733-9721 or Mr. Kevin Barnett in the DWQ Asheville
Regional Office at 828-296-4657.
Sincerely,
Alan W. Klimek, P.E., Director
Division of Water Quality
AW Klkhb
Enclosures: GC 3376
Certificate of Completion
Guidelines for Riparian Buffer Restoration
cc: Mike Osborne., CH2M Hill
4824 Parkway Plaza Blvd., Suite 200
Charlotte, NC 28217
USACE Asheville Regulatory Field Office
DWQ 401/Wetlands Central Office
DLR Asheville Regional Office
File Copy
Central Files
Filename: 05-1563. EWP. Big IvyCreek.Approval
Triage Check List
Date: 08/18/05
Kevin Barnett, Asheville Regional Office
To:
60-day Processing Time: 8/12/05 to 10/10/05
From: Cyndi Karoly Telephone: (919) 733-9721
DWQ #:05-1563
County: Buncombe
The file attached is being forwarded to you for your evaluation.
Please call if you need assistance.
? Stream length impacted
? Stream determination
Wetland determination and distance to blue-line surface waters on USFW topo maps
? Minimization/avoidance issues
? Buffer Rules (Neuse, Tar-Pamlico, Catawba, Randleman)
? Pond fill
Mitigation Ratios
? Ditching
? Are the stream and or wetland mitigation sites available and viable?
? Check drawings for accuracy
Is the application consistent with pre-application meetings?
? Cumulative impact concern
Comments: As per our discussion regarding revision of the triage and delegation processes,
please review the attached file. Note that you are the first reviewer, so this file will need to be
reviewed for administrative as well as technical details. If you elect to place this project on hold,
please ask the applicant to provide your requested information to both the Central Office in
Raleigh as well as the Asheville Regional Office. As we discussed, this is an experimental, interim
procedure as we slowly transition to electronic applications. Please apprise me of any
complications you encounter, whether related to workload, processing times, or lack of a "second
reviewer" as the triage process in Central had previously provided. Also, if you think of ways to
improve this process, especially so that we can plan for the electronic applications, let me know.
Thanks!
Project Name: Buncombe County EWP
Barnardsville 2005 - 45
Office Use Only: Fonn Version May 2002
USACE Action ID No. DWQ No.
(If any particular item is not applicable to this project, please enter "Not Applicable" or "N/A".)
1. Processing
1. Check all of the approval(s) requested for this project:
® Section 404 Permit ? Riparian or Watershed Buffer Rules
? Section 10 Pennit ? Isolated Wetland Permit from DWQ
® 401 Water Quality Certification
2. Nationwide, Regional or General Permit Number(s) Requested: Nationwide 37
3. If this notification is solely a courtesy copy because written approval for the 401 Certification
is not required, check here: ?
4. If payment into the North Carolina Wetlands Restoration Program (NCWRP) is proposed for
mitigation of impacts (verify availability with NCWRP prior to submittal of PCN), complete
section VIII and check here: ?
5. If your project is located in any of North Carolina's twenty coastal counties (listed on page
4), and the project is within a North Carolina Division of Coastal Management Area of
Environmental Concern (see the top of page 2 for further details), check hieere: I %
II. Applicant Information
2005
1. Owner/Applicant Information AvG 1 2?
Name: Jon Creighton /Assistant Coun Manager/Planning Director , _`?dATERnR6R11
Mailing Address: 46 Valley Street T?rc-
,?.n t!kDS?1DS????
Asheville, NC 28801
Telephone Number: 828-250-4835 Fax Number:
E-mail Address:
Agent/Consultant Information (A signed and dated copy of the Agent Authorization letter
must be attached if the Agent has signatory authority for the owner/applicant.)
Name: Mike Osborne
Company Affiliation: CH2M HILL
Mailing Address: 4824 Parkway Plaza Blvd.
Suite 200
Charlotte, NC 28217
Telephone Number: 704-329-0073 ext 252
E-mail Address: mike.osbomc(a)ch2m.com
Fax Number: 704-329-0141
Page I of 10
III. Project Information
Attach a vicinity map clearly showing the location of the property with respect to local
landmarks such as towns, rivers, and roads. Also provide a detailed site plan showing property
boundaries and development plans in relation to surrounding properties. Both the vicinity map
and site plan must include a scale and north arrow. The specific footprints of all buildings,
impervious surfaces, or other facilities must be included. If possible, the maps and plans should
include the appropriate USGS Topographic Quad Map and NRCS Soil Survey with the property
boundaries outlined. Plan drawings, or other maps may be included at the applicant's discretion,
so long as the property is clearly defined. For administrative and distribution purposes, the
USACE requires information to be submitted on sheets no larger than 11 by 17-inch fonnat;
however, DWQ may accept paperwork of any size. DWQ prefers full-size construction
drawings rather than a sequential sheet version of the full-size plans. If full-size plans arc
reduced to a small scale such that the final version is illegible, the applicant will be informed that
the project has been placed on hold until decipherable maps arc provided.
1. Name of project: Baniardsville EWP 2005-45
2. T.I.P. Project Number or State Project Number (NCDOT Only): NA
3. Property Identification Number (Tax PIN): 9775.01-37-0079
4. Location
County: Buncombe Nearest Town: Dillingham
Subdivision name (include phase/lot number): NA
Directions to site (include road numbers, landmarks, etc.
From I-40 From I-40 merge onto I-240 W via exit 53B toward Asheville and follow for
approximately 12 miles. Merge onto US-19 N / US-23 N toward Weaverville and take the
NC-197 (exitl5) toward Jupiter / Barnardsville. Turn right onto NC-197 / Barnardsville Hwy.
Turn right onto Dillingham Rd., stay straight to go onto Town Branch Rd. and Turn a slight
left onto Clinton Ln.
See Attachment 1 for site vicinity and parcel location.
5. Site coordinates, if available (UTM or Lat/Long): 36.009722°N 82.663611 °W
(Note - If project is linear, such as a road or utility line, attach a sheet that separately lists the
coordinates for each crossing of a distinct waterbody.)
6. Property size (acres)
3.8 Acres
7. Nearest body of water (stream/river/sound/ocean/lake): Dillingham Creek
River Basin: French Broad
(Note - this must be one of North Carolina's seventeen designated major river basins. The
River Basin map is available at littp://ii2o.enr.state.nc.us/admin/maps/.)
Page 2 of 10
Describe the existing conditions on the site and general land use in the vicinity of the project
at the time of this application:
The proposed sites are in agricultural and low-density residential uses. The stream and
stream banks were heavily impacted during Tropical Storms Frances and Ivan. Extensive
stream bank erosion threatens the stability of existing structures.
9. Describe the overall project in detail, including the type of equipment to be used:
EWP 2005-45
This project area consists of approximately 200 linear feet of Big Ivy Creek. The project
area is located at 36.009722°N 82.663611°W. High-water flows have threatened private
property and a state owned road. Attachment 1 contains representative photos of the eroded
area.
Repairs in this reach of stream will involve the following:
-Debris removal
-Stabilize the channel in its pre-flood configuration using organic and rock structures
-Reseed and plant woody vegetation
The techniques that will be utilized for the proposed repairs at the EWP site listed
above are described below.
Removal of Organic Debris
Fallen trees, limbs, and non-native material within the cross section of the existing or original
channel up to and including the debris line shall be removed. Any foreign debris (e.g. trash
appliances) will also be removed. Trees leaning over the channel whose near term fall is
apparent will be removed. These rooted trees will be cut three feet above the ground surface
and the root masses will be left in place. Disturbance of channel bottom and banks and
equipment access shall be held to the minimum necessary to allow the construction
equipment to remove the debris. All areas disturbed due to debris removal and equipment
access shall be reshaped and reseeded. Access to the channel will be perpendicular to the
channel so that cutting of trees is held to a minimum with precaution taken to protect mast
production and stream canopy trees. These trees will be cut off at ground level so re-
sprouting may occur after construction. Dead trees and small brush piles that provide den
habitat and are determined to pose no hazard to the channel will be protected. Woody debris
will be chipped and disposed of in upland areas or hauled offsite.
Streambank Repair
When possible, excavation equipment will access strcambank repair areas from the dry and
will not track into the stream channel. Most of the steep eroded streambanks are opposite or
adjacent to the debris removal areas. At these areas, the rocky material removed from the
floodplain will be used to stabilize the stream bank, with the addition of large boulders along
the toe of the slope as necessary to stabilize and protect the toe. Where suitable material is
available, rock vane and root wads will be installed in the restored bank section to reduce
bank stress and provide stability to the unconsolidated fill.
Page 3 of 10
An existing cross section and site specific design components are included in Attachments 1
and 2 for each of the impacted channel sections requiring stabilization. Drainage areas of
project areas are also included in those attachments. The drainage area is used to determine
the design storm peak flow using USGS Rural Regression equations for the Blue Ridge-
Piedmont. Design storm velocity and slicar stress values were also calculated. This
information, in conjunction with the field investigation analysis, DSR notations, and agency
guidance and regulations, are used to develop an appropriate streambank stabilization design.
Additional information on general design features, erosion control practices and debris
removal practices is included in Attachment 3.
Equipment that may be used to accomplish the above listed tasks includes; rubber tired
skidders, 15 ton dump truck, hydraulic track mounted excavator with thumb, and chainsaws.
10. Explain the purpose of the proposed work:
The work addressed in this application is intended to improve post flood hydraulic capacity
of the stream reaches discussed and stabilize severely eroded streambanks that are
threatening structures or other property. The proposed actions are not intended to enhance
existing conditions or restore stream reaches using natural channel design techniques. Such
activities would require detailed engineering evaluation and design, which are beyond the
intent of the EWP program.
IV. Prior Project History
If jurisdictional determinations and/or permits have been requested and/or obtained for this
project (including all prior phases of the same subdivision) in the past, please explain. Include
the USACE Action ID Number, DWQ Project Number, application date, and date permits and
certifications were issued or withdrawn. Provide photocopies of previously issued permits,
certifications or other useful information. Describe previously approved wetland, stream and
buffer impacts, along with associated mitigation (where applicable). If this is a NCDOT project,
list and describe permits issued for prior segments of the same T.I.P. project, along with
construction schedules. NA
V. Future Project Plans
Are any future permit requests anticipated for this project? If so, describe the anticipated work,
and provide justification for the exclusion of this work from the current application. NO
VI. Proposed Impacts to Waters of the United States/Waters of the State
It is the applicant's (or agent's) responsibility to determine, delineate and map all impacts to
wetlands, open water, and stream channels associated with the project. The applicant must also
provide justification for these impacts in Section VII below. All proposed impacts, permanent
and temporary, must be listed herein, and must be clearly identifiable on an accompanying site
plan. All wetlands and waters, and all streams (intermittent and perennial) must be shown on a
delineation map, whether or not impacts are proposed to these systems. Wetland and stream
evaluation and delineation forms should be included as appropriate. Photographs may be
Page 4 of 10
included at the applicant's discretion. If this proposed impact is strictly for wetland or stream
mitigation, list and describe the impact in Section VIII below. If additional space is needed for
listing or description, please attach a separate sheet.
1. Provide a written description of the proposed impacts:
Proposed impacts include limited streambed disturbances, debris removal, and strcambank
stabilization.
2. Individually list wetland impacts below:
Wetland Impact
Site Number
(indicate on ma)
Type of Impact* Area of
Impact
(acres) Located within
100-year Floodplain**
(es/no) Distance to
Nearest Stream
(linear feet
Type of Wetland***
* List each impact separately and identify temporary impacts. Impacts include, but are not limited to: mechanized clearing, grading, fill,
excavation, flooding, ditching/drainage, etc. For dams, separately list impacts due to both structure and flooding.
** 100-Year floodplains are identified through the Federal Emergency Management Agency's (FEMA) Flood Insurance Rate Maps
(FIRM), or FEMA-approved local floodplain maps. Maps are available through the FENIA Map Service Center at I-800-358-9616, or
online at hitn:?'/vvww.fema.eov.
*** List a wetland type that best describes wetland to be impacted (e.g., freshwater/saltwater marsh, forested wetland, beaver pond,
Carolina Bay, bog, etc.) Indicate if wetland is isolated (determination of isolation to be made by USACE only).
List the total acreage (estimated) of all existing wetlands on the property: None
Total area of wetland impact proposed: NA
3. Individually list all intermittent and perennial stream impacts below:
Stream Impact Length of Average Width Perennial or
Site Number Type of Impact* Impact Stream Name** of Stream Before Intermittent?
indicate on ma) linear feet) Impact (please secif
EWP 2005-45 Streambank 200 Big Ivy Creek 20ft Perennial
Stabilization
* List each impact separately and identify temporary impacts. Impacts include, but are not limited to: culverts and associated rip-rap,
dams (separately list impacts due to both structure and flooding), relocation (include linear feet before and after, and net loss/gain),
stabilization activities (cement ),vall, rip-rap, crib wall, gabions, etc.), excavation, ditching/straightening, etc. If stream relocation is
proposed, plans and profiles showing the linear footprint for both the original and relocated streams must be included.
** Stream names can be found on USGS topographic maps. If a stream has no name, list as UT (unnamed tributary) to the nearest
downstream named stream into which it flows. USGS maps are available through the USGS at 1-800-358-9616, or online at
\v\v\v.usas.!ov. Several internet sites also allow direct download and printing of USGS maps (e.g., \v\v\v.topozone.ami,
\4'\V\V.mat1000S(.C01n, etc.).
Cumulative impacts (linear distance in feet) to all streams on site: 200
4. Individually list all open water impacts (including lakes, ponds, estuaries, sounds, Atlantic
Ocean and any other water of the U.S.) below:
Open Water Impact
Site Number
indicate on ma
Type of Impact* Area of
Impact
acres Name Waterbody
(if applicable) Type of Waterbody
(lake, pond, estuary, sound,
bay, ocean, etc.)
Page 5 of 10
* List each impact separately and identify temporary impacts. Impacts include, but are not limited to: fill, excavation, dredging,
flooding, drainage, bulkheads, etc.
5. Pond Creation
If construction of a pond is proposed, associated wetland and stream impacts should be
included above in the wetland and stream impact sections. Also, the proposed pond should
be described here and illustrated on any maps included with this application.
Pond to be created in (check all that apply): ? uplands ? stream ? wetlands
Describe the method of construction (e.g., dam/embankment, excavation, installation of
draw-down valve or spillway, etc.): NA
Proposed use or purpose of pond (e.g., livestock watering, irrigation, aesthetic, trout pond,
local stormwater requirement, etc.): NA
Size of watershed draining to pond: NA Expected pond surface area: NA
VII. Impact Justification (Avoidance and Minimization)
Specifically describe measures taken to avoid the proposed impacts. It may be useful to provide
information related to site constraints such as topography, building ordinances, accessibility, and
financial viability of the project. The applicant may attach drawings of alternative, lower-impact
site layouts, and explain why these design options were not feasible. Also discuss how impacts
were minimized once the desired site plan was developed. If applicable, discuss construction
techniques to be followed during construction to reduce impacts.
When at all possible equipment will be kept out of the stream channel, stream crossings will be
minimized, and no excavation will be below the existing channel bed. When at all possible
stream material will be moved from dry areas to banks, minimizing the movement of wet (or
below water line) stream material. Creating wide, shallow channels will be avoided. Temporary
and/or permanent herbaceous vegetation sliall be planted on all bare soil within 15 days of
ground disturbing activities. Rocky material shall not be used for bank stabilization above the
normal high water mark. Large rocky material will be brought in to stabilize the toe of impacted
streambanks where necessary.
Page 6 of 10
VIII. Mitigation
DWQ - In accordance with 15A NCAC 211 .0500, mitigation may be required by the NC
Division of Water Quality for projects involving greater than or equal to one acre of impacts to
freshwater wetlands or greater than or equal to 150 linear feet of total impacts to perennial
streams.
USACE - In accordance with the Final Notice of Issuance and Modification of Nationwide
Pennits, published in the Federal Register on March 9, 2000, mitigation will be required when
necessary to ensure that adverse effects to the aquatic environment are minimal. Factors
including size and type of proposed impact and function and relative value of the impacted
aquatic resource will be considered in determining acceptability of appropriate and practicable
mitigation as proposed. Examples of mitigation that may be appropriate and practicable include,
but are not limited to: reducing the size of the project; establishing and maintaining wetland
and/or upland vegetated buffers to protect open waters such as streams; and replacing losses of
aquatic resource functions and values by creating, restoring, enhancing, or preserving similar
functions and values, preferable in the same watershed.
If mitigation is required for this project, a copy of the mitigation plan must be attached in order
for USACE or DWQ to consider the application complete for processing. Any application
lacking a required mitigation plan or NCWRP concurrence shall be placed on hold as
incomplete. An applicant may also choose to review the current guidelines for stream restoration
in DWQ's Draft Technical Guide for Stream Work in North Carolina, available at
littp://li2o.enr.state.nc.us/ncwctlands/strmgide.litml.
Provide a brief description of the proposed mitigation plan. The description should provide
as much information as possible, including, but not limited to: site location (attach directions
and/or map, if offsite), affected stream and river basin, type and amount (acreage/linear feet)
of mitigation proposed (restoration, enhancement, creation, or preservation), a plan view,
preservation mechanism (e.g., deed restrictions, conservation casement, etc.), and a
description of the current site conditions and proposed method of construction. Please attach
a separate sheet if more space is needed. NA
2. Mitigation may also be made by payment into the North Carolina Wetlands Restoration
Program (NCWRP). Please note it is the applicant's responsibility to contact the NCWRP at
(919) 733-5208 to determine availability and to request written approval of mitigation prior
to submittal of a PCN. For additional information regarding the application process for the
NCWRP, check the NCWRP website at http://li2o.enr.state.nc.us/wrp/index.litm. If use of
the NCWRP is proposed, please check the appropriate box on page three and provide the
following infornation:
Amount of stream mitigation requested (linear feet): NA
Amount of buffer mitigation requested (square feet): NA
Amount of Riparian wetland mitigation requested (acres): NA
Amount of Non-riparian wetland mitigation requested (acres): NA
Amount of Coastal wetland mitigation requested (acres): NA
Page 7 of 10
IX. Environmental Documentation (required by DWQ)
Does the project involve an expenditure of public (federal/state) funds or the use of public
(federal/state) land?
Yes ® No ?
If yes, does the project require preparation of an environmental document pursuant to the
requirements of the National or North Carolina Environmental Policy Act (NEPA/SEPA)?
Note: If you are not sure whether a NEPA/SEPA document is required, call the SEPA
coordinator at (919) 733-5083 to review current thresholds for environmental documentation.
Yes ? No
If yes, has the document review been finalized by the State Clearinghouse? If so, please attach a
copy of the NEPA or SEPA final approval letter.
Yes ? No ?
X. Proposed Impacts on Riparian and Watershed Buffers (required by DWQ)
It is the applicant's (or agent's) responsibility to determine, delineate and map all impacts to
required state and local buffers associated with the project. The applicant must also provide
justification for these impacts in Section VII above. All proposed impacts must be listed herein,
and must be clearly identifiable on the accompanying site plan. All buffers must be shown on a
map, whether or not impacts are proposed to the buffers. Correspondence from the DWQ
Regional Office may be included as appropriate. Photographs may also be included at the
applicant's discretion.
Will the project impact protected riparian buffers identified within 15A NCAC 213 .0233
(Ncuse), 15A NCAC 213 .0259 (Tar-Pamlico), 15A NCAC 213 .0250 (Randleman Rules and
Water Supply Buffer Requirements), or other (please identify )?
Yes ? No ® If you answered "yes", provide the following information:
Identify the square feet and acreage of impact to each zone of the riparian buffers. If buffer
mitigation is required calculate the required amount of mitigation by applying the buffer
multipliers.
Zone* Impact
(square feet) Multiplier Required
Mitigation
1 3
2 1.5
Total
' Zone I extends out 30 feet perpendicular from near bank of channel; Zone 2 extends an
additional 20 feet from the edge of Zone 1.
If buffer mitigation is required, please discuss what type of mitigation is proposed (i.e., Donation
of Property, Conservation Easement, Riparian Buffer Restoration / Enhancement, Preservation or
Payment into the Riparian Buffer Restoration Fund). Please attach all appropriate information as
identified within 15A NCAC 213 .0242 or.0260.
Page 8 of 10
XI. Stornnvater (required by DWQ)
Describe impervious acreage (both existing and proposed) versus total acreage on the site.
Discuss stormwater controls proposed in order to protect surface waters and wetlands
downstream from the property.
Imperviousness will not change.
Erosion and sedimentation prevention and control will be maintained throughout this project
primarily through: proper water management, construction sequencing, proper staging and
stockpiling of materials, and the maintenance, at all times, of suitable channel capacity for
expected flow events. Equipment, fuels, lubricants, or other potential sources of water pollution
will not be stored in areas that could be flooded during this project.
XH. Sewage Disposal (required by DWQ)
Clearly detail the ultimate treatment methods and disposition (non-discharge or discharge) of
wastewater generated from the proposed project, or available capacity of the subject facility.
Portable facilities shall be provided at the work site.
X1U. Violations (required by DWQ)
Is this site in violation of DWQ Wetland Rules (15A NCAC 2H .0500) or any Buffer Rules?
Yes ? No
Is this an after-the-fact permit application?
Yes ? No
XIV. Other Circumstances (Optional):
It is the applicant's responsibility to submit the application sufficiently in advance of desired
construction dates to allow processing time for these permits. However, an applicant may
choose to list constraints associated with construction or sequencing that may impose limits on
work schedules (e.g., draw-down schedules for lakes, dates associated with Endangered and
Threatened Species, accessibility problems, or other issues outside of the applicant's control).
NA
plican cnt's ig nature ll tc
(Agen 's signature is va ' only if an authorization letter from the applicant is provided
Page 9 of 10
Table 1.
DSR Map ID PIN Owner Property Owner's City State Zip Streambank
Number size Address stabilization
(acres)
EWP 2005- DSR45 9775.01.37- I lilda Floyd 3.8 217 Hamburg Weaverville NC 28787 200 LF
45 0079.000 Mountain Rd
Page 10 of 10
Attachment 1- DSR 45
Ia. Vicinity Map
Ib. Site Map
lc. Site Photos
Id. Cross Section and Site Specific Design Page
I c. Drainage Areas
Access Agreements
I? l , t ft ? /?
a F'
t ?' + l
t ;
IA?
i??_, 4644• `?
r
+
\`? `?i
" '-J - - _?
? , ? /+ 1. ?
s le ! .?
.S
` - f 4200. ` DIL41N p 1 ? L
- ? _ ' ? ) i/ ? Ail ??? r.? ? • ? ? " ? - ?? -? ?,,,_,.l
All,
J??( - \; 46??; ' ?t >
t
E$ER
N
A Barnardsville, N.C. USGS Quad Buncombe County Stream Assessment
Barnardsville Watershed
500 0 500 Feet DSR-45
Hilda Floyd
CH2MHILL
low
Attachment 2b
DSR 45 - Dillingham Creek Watershed
Buncombe County, NC
Hilda Floyd Parcel 0079
Hilda Floyd
DSR Site 45
Attachment 1 d
DSR 45 - Barnardsville Watershed
Buncombe County, NC
Hilda Floyd existing cross section
12
8
6 a
-
4
a?
2 Z
0
1 0 120 1 00 -2
-4
Width (feet)
Right Top of Bank
Left Top of Bank
Water Surface
i
80 6
0 40 2
0
10
wa?
Buncombe Co., Ivy Watershed - Ivy Creek (River), DSR 45
Design Parameters
Apply to Site
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Figure Title Notes and/or Measurements
1 BANK STABILIZATION TYPICAL SECTION
2 BANK STABILIZATION WITH ROCK TOE TYPICAL SECTION 200 LF of right bank, A=4.5 ft, See Note 1
3 STREAM CHANNEL BENCH TYPICAL SECTION
4 TYPICAL J HOOK DETAIL
5 TYPICAL CROSS VANE DETAIL
6 SUGGESTED VEGETATION LIST
7 STABILIZATION PLANTING PLAN See Note 2
8 BENCH PLANTING PLAN
9 LIVE STAKE DETAIL
10 DEAD STOUT STAKE DETAIL
11 EC FABRIC INSTALLATION DETAIL EC fabric = 4.5 Ib/ft2
12 EC FABRIC ANCHOR DETAIL
13 STABILIZATION CONSTRUCTION ENTRANCE DETAIL
14 TEMPORARY SILT FENCE DETAIL
15 TEMPORARY STREAM CROSSING DETAIL
16 LAND QUALITY STOCK PILE LAYOUT -,?
17 LAND QUALITY STREAM CROSSING LAYOUT
18 LAND QUALITY DEBRIS REMOVAL LAYOUT
Note 1 Backfill from existing top of bank at 3:1 slope. Regrade cobble point bar to center flow. See site sketch.
50 LF of woody and manmade debris removal
JED..
08/05/2005
zoos
0 ??
Note 2 Zone 2: Do not plant trees in Powerline ROW -instead double the typical quantity of shrubs and plant on a 5' center.
Legend
DSR Project Site
Interstate Highway
Major Road
Major Hydrography
Subwatershed
Municipality
County Boundary
YC.
?73
JAI
DSR-45
Drainage Area 48.6 sq. miles
tAc'Acjq
0 0.5 1 2 Miles
I I I I I I I I I
N
10 CH2MHILL A
Barnardsville Watershed,
DSR-45
Buncombe County, NC
Hilda Floyd
Drainage Area Map
C-) L-'
PERMIT FOR EMERGENCY WATERSHED PROTECTION (EWP)
The undersigned landowners hereby grant permission to Buncombe County and the Buncombe
County Soil and Water Conservation District and/or their agents to enter upon our land for the
purpose of repairing the flood damage of stream channels and stream banks in the
watershed.
This permit includes the right to spread soil, remove and dispose of debris, install needed
measures, seed and mulch, and perform similar emergency watershed protection work
necessitated by the floods of September, 2004.
This permit also includes the right of ingress and egress on the land for the purpose of
maintaining or inspecting maintenance of the emergency works for the period of 1 year from the
date of completion. Work areas covered by this permit are sketched on the reverse of this form
or on an attached sheet.
Si ned Date Signed Date
01 ?'
General Notes
The Contractor shall make his own determination of the
existing subsurface conditions. In areas where proposed
construction may conflict with existing utilities, the Contractor
shall take all necessary precautions to avoid damage to the
utilities. Notify and locate all impacted utilities at least 48
hours prior to excavation. Any damage sustained to utilities
shall be repaired by or under the direction of the utility owner
at the Contractor's expense.
All existing facilities, including but not limited to sidewalks,
roads, lawns, landscape vegetation, etc., inside and outside of
construction limits that are disturbed under this contract shall
be reestablished and/or reconstructed to the original condition
at the Contractor's expense.
Construction Sequence
1. Begin work at the upstream end of the project reach.
2. Construct proposed structures according to the plans and
specifications.
3. Grade stream banks to proposed grade, and tie into
existing banks upstream and downstream.
4. Overbank areas (beyond top of bank) adjacent to the
project reach shall be graded for positive drainage toward
the stream.
5. Apply temporary stabilization to the disturbed areas at the
end of each work day.
6. Repeat steps 1 through 5 for each segment of the project
reach, working downstream.
Site Stabilization
1. Conduct soil test to confirm necessary lime and fertilizer
amendments. Appropriate lime and fertilizer shall be
applied prior to seeding and incorporated to a depth 3 to 5
inches below the surface.
2. Temporary stabilization will be applied to all disturbed
areas on a daily basis. Areas shall be seeded with rye
grass at a rate of 15 lbs./ac. and long straw or hay
mulched. Straw shall consist of thoroughly threshed wheat,
rye or oat straw, reasonably bright in color, and shall not
be musty, moldy, caked, decayed, or excessively dusty
and shall be free of noxious weed seeds.
3. Permanent soil stabilization shall be completed within 7
calendar days of initial soil disturbance or re-disturbance.
Planting and seeding shall be incorporated into the subsoil
at the rates prescribed on Figures 6, 7, and 8. Contractor
shall follow NCDWQ Guidelines for Riparian Restoration,
http://h2o.enr.state.nc.us/wrp/pdf/buffers.pdf
4. All earth fill in excess of 1 ft depth should be installed in
lifts of maximum 6-inches and mechanically compacted.
5. All rock used for bank stabilization and in-stream structures
shall be 3 ft to 4 ft angular rock.
6. Erosion Control (EC) Fabric shall be woven coir mat,
secured with dead stout stakes, and shall meet the
following standards:
50% open area (maximum)
0.5 inch maximum opening size
4.5 lbs. per sq. foot maximum sheer stress
10 fps minimum velocity
CLT/GENERAL NOTES_NF.DOC
USE OR DISCLOSURE OF DATA CONTAINED ON THIS SHEET IS SUBJECT TO
THE RESTRICTION ON THE TITLE PAGE OF THIS PROPOSAL.
7. Filter fabric shall be Amoco Propex 2002 woven geotextile
or equivalent. Cut excess filter fabric so no fabric is visible
after installation.
8. Seeded areas not specified for coir fabric, shall be
mulched with long straw or hay mulch immediately after
seeding areas at a rate of 2 tons/acre (uniform loose depth
of 1" to 2"). Straw shall consist of thoroughly threshed
wheat, rye or oat straw, reasonably bright in color, and
shall not be musty, moldy, caked, decayed, or excessively
dusty and shall be free of noxious weed seeds. Mulch
shall be secured with biodegradable netting (Robex Super
Flow or Equal).
9. The Contractor shall be responsible for maintaining seeded
areas until 95% vegetative cover is established. Should
any seeded area fail to germinate, or washing of any areas
occur requiring re-establishment of seeding, the Contractor
shall replace any lost soil material and re-seed and
re-mulch such areas at Contractor's expense.
Standard Erosion and Sediment Control Notes
1. The Contractor shall protect all points of construction
ingress and egress by installing a temporary construction
entrance as shown in details to prevent the deposition of
materials onto public roads. All materials deposited onto
public roads shall be removed immediately.
2. The Contractor shall re-vegetate or restore access roads
(including construction entrance) to match pre-construction
conditions.
3. The Contractor shall inspect daily and maintain
continuously in an effective operating condition all erosion
and sediment control measures until such times as they
are removed with prior permission from Engineer or
agency inspector.
4. The Contractor shall protect trees and landscaping not
marked for disposal from damage. Any damage that
occurs shall be repaired at the Contractor's expense.
5. Fencing shall be maintained for animal containment. The
Contractor shall provide temporary fencing to allow for
execution of the work. The Contractor shall keep
construction equipment away from livestock and take all
precautions to prevent injury to animals.
CLT/GENERAL NOTES_NF.DOC
USE OR DISCLOSURE OF DATA CONTAINED ON THIS SHEET IS SUBJECT TO
THE RESTRICTION ON THE TITLE PAGE OF THIS PROPOSAL.
PROPOSED GRADE
BASE FLOW
EXISTING STREAMBED
NOTE:
HEIGHT "A" IS MEASURED
FROM DEEPEST POINT IN
CHANNEL CROSS-SECTION
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
TITLE
FIGURE
H2M H I LL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, INC 28217
BANK STABILIZATION
TYPICAL SECTION
N TS
1
/---EXISTING TOP OF BANK
PROPOSED GRADE
NOTES:
1. HEIGHT "A" IS MEASURED FROM
DEEPEST POINT IN CHANNEL
CROSS-SECTION.
2. FILTER FABRIC SHALL BE AMOCO PROPEX 2002
WOVEN GEOTEXTILE OR EQUIVALENT.
LAY FILTER FABRIC UNDER TRENCH ROCK
AND UP BEHIND ROCKS. CUT EXCESS
FILTER FABRIC SO NO FABRIC IS VISIBLE
AFTER INSTALLATION. BACKFILL WITH WELL-DRAINING
SOIL (USE NATIVE MATERIAL WHENEVER POSSIBLE).
MIN. OVERLAP OF COIR OVER FILTER FABRIC OF 12".
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
EXISTING TOP OF BANK
\-CUT--\
7>1?
3 MIN.
(NOT STEEPER)
EC FABRIC
SEE FIGURE 7
FILTER FABRIC
KEY IN ROCK TOE
ONE ROCK DIAMETER
4' MIN.
CH2MHILL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, INC 28217
2' MIN. OF
EXPOSED
ROCK
Ll
2
ROCK TOE
- 2' MIN. OF ROCK
EMBEDDED IN BANK
-7
BASE FLOW A
EXISTING STREAMBED
TITLE
BANK STABILIZATION
WITH ROCK TOE
TYPICAL SECTION
N TS
FIGURE
z
EXISTING TOP OF BANK EXISTING GRADE
CUT
PROPOSED GRADE 1 1
3 MIN. CB
(NOT STEEPER)
2
EC FABRIC
SEE FIGURE 7 GRADE TO DRAIN 1
(1% MAX.) I
FILL
STREAM CHANNEL BENCH \
NOTES:
1. HEIGHT "A" IS MEASURED FROM
DEEPEST POINT IN CHANNEL
CROSS-SECTION.
2. FILTER FABRIC SHALL BE AMOCO PROPEX 2002
WOVEN GEOTEXTILE OR EQUIVALENT.
LAY FILTER FABRIC UNDER TRENCH ROCK
AND UP BEHIND ROCKS. CUT EXCESS
FILTER FABRIC SO NO FABRIC IS VISIBLE
AFTER INSTALLATION. BACKFILL WITH WELL-DRAINING
SOIL (USE NATIVE MATERIAL WHENEVER POSSIBLE).
MIN. OVERLAP OF COIR OVER FILTER FABRIC OF 12".
EXISTING STREAMBED r
?l
FILTER FABRIC
KEY IN ROCK TOE
ONE ROCK DIAMETER
4' MIN.
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
CH2MH1LLo
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, INC 28217
TITLE
STREAM CHANNEL
BENCH
TYPICAL SECTION
NTS
T
BASE FLOW A
1
FIGURE
3
BANKFULL ELEVATION
CROSS SECTION VIEW
BOULDER
BANKFULL ELEVATION
DIRECTION ?I
FLOW --------- MM??
-T --
?-2-77. I
2
FOOTER -'
NOTES: PROFILE VIEW
1. BOULDER SIZE IS 4' MINIMUM ORAS
SPECIFIED ON PLANS.
2. WRAP FILTER FABRIC AROUND FOOTER STONES
AND BACKFILL WITH TYPE 3 RIPRAP OR EQUIVALENT
(ON SITE COBBLE WHEN AVAILABLE).
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
CH2MHBLL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
CHANNEL BED
FLOW G
DIRECTION ll\
O
vy?? "s
G
GAPS \
(1/4-1/3 ROCK DIA.)
o O 2
M
1
SCOUR POOL I
PLAN VIEW
BOULDERS
W
SOURCE: APPLIED ECOLOGICAL SERVICES. INC
TITLE FIGURE
TYPICAL J HOOK DETAIL
4
NOT TO SCALE
FOOTER
5'MIN.
--? 5'MIN. BANKFULL WIDTH I r I SILL -
----- ---------j BOULDERS
- e
5'MW.
CROSS SECTION VIEW
NOTES:
1. BOULDER SIZE IS 4' MINIMUM OR AS
SPECIFIED ON PLANS.
4. _
FOOTER
r--BANKFULL ELEVATION
\J
Y
Q
m
FLOW
U R ECTI ON
4
1
Q
Q1
20'
z
2/3 W
1 O
SCOUR POOL
PLAN VIEW
TRENCHED IN 3' MIN.
AND COVERED
FLOW
I -:12_7K DIRECTION
BOULDERS CHANNEL BED
PROFILE VIEW
2. WRAP FILTER FABRIC AROUND FOOTER STONES
AND BACKFILL WITH TYPE 3 RIPRAP OR EQUIVALENT
(ON SITE COBBLE WHEN AVAILABLE).
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
CH2MHILL.
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
SILL MUST BE TIED IN TO
BANKFULL ELEVATION
SOURCE: APPLIED ECOLOGICAL SERVICES, INC
TITLE FIGURE
TYPICAL CROSS VANE
DETAIL
NOT TO SCALE
Mountain Region Suggested Vegetation List
TREES S P F SMALL TREES/SHRUBS S P F HERBACEOUS V
Betula lenta Alnus serrulata Arisaema triphyllu
cherry birch x x tag alder x x x jack-in-the-pulpit
Betula nigra Amelanchierarborea Asclepias incarnat
river birch x x serviceberry x x swamp milkweed
Carya cordiformis Aronia arbutifolia Carex crinata
bitternut hickory x x x red chokeberry x x fringed sedge
Carya ovata Asimina triloba Carex intumescens
shagbark hickory x x x common pawpaw x x bladder sedge
Diospyros virginiana Calycanthus floridus Carex lupulina
persimmon x x x sweet-shrub x x hop sedge
Fraxinus pennsylvanica Carpinus caroliniana Carex lurida
green ash x x ironwood x x lurid sedge
Halesia caroliniana Cornus alternifolia Carex scoparla
silverbell x x alternate leaf dogwood x x broom sedge
Nyssa sylvatica Cornus amomum Carex stricta
blackgum x x x silky dogwood x x tussock sedge
Platanus occidentalis Corylus americana hazel- Carex vulpinoidea
sycamore x x nut x x fox sedge
Prunus serotina Hamamelis virginiana Chelone glabra
black cherry x x x witch-hazel x x turtlehead
Salix nigra Ilex verticillata Cyperus strigosus
black willow x x winter berry x x x umbrella sedge
Tilia heterophylla Leucothoe axillaris Elymus hystrix
white basswood x x doghobble x bottlebrush grass
Lindera benzoln Eupatorium fistulos
S = Shade spicebush x Joe-pye-weed
P = Partial Sun Lyonia ligustrina x Eupatorium perfolia
F = Full Sun Lyonia ligustrina boneset
Magnolia tripetala x Impatiens capensis
umbrella tree iewei-weed
Physocarpus opulifolius
ninebark x x x
Rhododendron
periclymenoides
wild azalea x x
Rhododendron viscosum
swamp azalea x x
Rosa palustris
swamp rose x x
Salix sericea
silky willow x x
Spirea latifolia
meadowsweet x
Symplocos tinctoria
sweet leaf x x
Viburnum cassinoides
W ithe-rod x x x
Xanthorhiza simplicissima
vellow-root x
EGETATION FOR SEED MIX
m Scirpus validus
soft stem bulrush
a Sparganium americanum
bur-reed
Thelypteris palustris
marsh fern
Uniola latifolia
river oats
Vernonia noveboracensh
ironweed
Leersia oryzoides
rice cutgrass
Lobelia cardinalis
cardinal flower
Lobelia siphilitica
great blue lobelia
Ludwigia alternifolia
bushy seedbox
Panicum virgatum
switchgrass
Polygonum sagittatum
tearthum b
Scirpus atrovirens
green bulrush
um Scirpus cyperinus
woolgrass
tum Juncus effusus
soft rush
TITLE DRAWN: GMH
SUGGESTED VEGETATION LIST PROD-MANAGER: JMO
DATE: 5/2005
CH2MHILL FIGURE
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217 6
APPRox.
WIDTH OF CHANNEL
Z
LIVE STARE ZONE
TO EDGE OF WATER
PLANTING WIDTH WILL VARY TO
LANDOWNER COMPLIANCE AND
PROJECT SPECIFICATIONS.
EXISTING SURFA
ELEVATI
ZONE I ZONE 2
SYMBOL HERBACEOUS SEEDING DESCRIPTION SYMBOL WOODY VEGETATION DESCRIPTION
NATIVE TREE AND SHRUB SPECIES TO BE PLANTED A
-TD BE SEEDED IMMEDIATELY WITH TEMPORARY RYE GRASS A DENSITY OF 436 TREES/ACRE, WHICH IS
AT 15 LBS/ACRE SEEDING RATE. SUFFICIENT TO PROVIDE 320 TREES/ACRE
-FOLLOWING CONSTRUCTION, AREA TO BE SEEDED WITH
A NATIVE, PERMANENT GRASS/HERB MIXTURE AT
15-20 LBS/ACRE SEEDING RATE.
ME AT MATURITY. FOLLOW NCDWO GUIDELINES
FOR RIPARIAN BUFFER RESTORATION.
-SHRUB SPECIES INCLUDE BUT ARE NOT LIMITED TO:
-HERB/GRASS SPECIES INCLUDE BUT ARE NOT LIMITED TO: Anus serratula, Cephalanthus occidentalis,
Agrostis alba
Carex spp.
DacWis glomorata / Cornus stricta, Rhododendron maximum, salix
,
,
,
Panicum spp., Pennisetum glaucum, Secale cereale serecia, Sambucus canadensis, etc.
,
ETC. -TREE SPECIES INCLUDE BUT ARE NOT LIMITED TO:
LIVE STAKES TO INCLUDE Cornus S
pp and Acerspp., Betula spp., Fraxinus spp., Juglands
Nigra, Liriodendron Tulipitera., Pinus strobus.,
LIVE STAKES SPACED ON 2'
LIVE CENTERS P/atanus occidentalis., Robinia Pseudoacacia., etc.
-TO BE SEEDED IMMEDIATELY WITH TEMPORARY RYE GRASS.
-FOLLOWING CONSTRUCTICN, AREA TO BE SEEDED WITH
A NATIVE, PERMANENT GRASS/HERB MIXTURE AT
15-20 LBS/ACRE SEEDING RATE.
AT LEAST 3 SPECIES OF TREES AND 5 SPECIES OF
•Nnrcc SHRUBS SHOULD BE USED.
-TREE/SHRUB/GRASS SPECIES LISTED ARE SUBJECT TO CHANGE DUE TO AVAILABILITY FROM LOCAL NURSERIES AND
FORESTRY SUPPLY STATIONS.
SUBSTITUTION MUST BE APPROVED BY ENGINEER.
SOURCE: ALTAMONT ENVIRONMENTAL INC.
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
CH2MHILL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, INC 28217
EXISTING STREAMBED
TITLE
STABILIZATION
PLANTING PLAN
FIGURE
7
APPROA
WIDTH OF CHANNEL
13
r`0 T
LIVE STAKE ZONE
TO EDGE OF WATER
PLANTING WIDTH WILL VARY TO
LANDOWNER COMPLIANCE AND
PROJECT SPECIFICATIONS.
ZONE I ZONE 2
SYMBOL HERBACEOUS SEEDING DESCRIPTION SYMBOL WOODY VEGETATION DESCRIPTION
NATIVE TREE AND SHRUB SPECIES TO BE PLANTED AT
-TO BE SEEDED IMMEDIATELY WITH TEMPORARY RYE GRASS A DENSITY OF 436 TREES/ACRE. WHICH
AT 15 LBS/ACRE SEEDING RATE. SUFFICIENT TO PROVIDE 320 TREES/ACRE
-FOLLOWING CONSTRUCTION, AREA TO BE SEEDED WITH
A NAT
E
PER
E
T GR
/ AT MATURITY. FOLLOW NCDWO GUIDELINES
FOR RIPARIAN BUFFER RESTORATION.
IV
,
MAN
N
ASS
HERB MIXTURE AT
15-20 LBS/ACRE SEEDING RATE. -SHRUB SPECIES INCLUDE BUT ARE NOT LIMITED TO:
-HERB/GRASS SPECIES INCLUDE BUT ARE NOT LIMITED TO: Alnus serratula, Cepha/anthus occidentalis,
C
Agrostis alba, Carex spp., Dactylis glomerata, ornus stricta, Rhododendron maximum, salix
serecia, Sambucus canadensis
etc.
Panicum spp., Pennisetum glaucum, Seca/e cerea/e,
ETC. ,
-TREE SPECIES INCLUDE BUT ARE NOT LIMITED T0:
LIVE STAKES TO INCLUDE Comus spA and Acer spp., Betula spp., Fraxinus spp., Juglands
Salix serica Nigra, Liriodendron Tulipifera., Pinus strobus.,
LIVE STAKES SPACED ON 2' CENTERS P/atanus occidentalis., Robinia Pseudoacacia., etc.
-TO BE SEEDED IMMEDIATELY WITH TEMPORARY RYE GRASS.
-FOLLOWING CONSTRUCTION, AREA TO BE SEEDED WITH
A NATIVE, PERMANENT GRASS/HERB MIXTURE AT
15-20 LBS/ACRE SEEDING RATE.
AT LEAST 3 SPECIES OF TREES AND 5 SPECIES OF
SHRUBS SHOULD BE USED.
'NOTES:
-TREE/SHRUB/GRASS SPECIES LISTED ARE SUBJECT TO CHANGE DUE TO AVAILABILITY FROM LOCAL NURSERIES AND
FORESTRY SUPPLY STATIONS.
PLANT ZONE I TO EDGE OF WATER
- SUSTITUTION MUST BE APPROVED BY ENGINEER
SOURCE: ALTAMONT ENVIRONMENTAL, INC.
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
11211/ HILL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
TITLE
BENCH
PLANTING PLAN
EXISTING STREAMBED J
FIGURE
8
EC FABRIC
2' MAX
SPACING
O
0
30" LIVE CUTTING
(DORMANT) - TYP
DEAD STOUT STAKE
TYP, SEE FIGURE 10
NOTE:
INSTALL LIVE STAKE SO
2/3 LENGTH IS (MIN. 20")
BELOW GROUND
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
CH2MHILL
4824 PARKWAY PLAZA BOULEVARD
S= 200
CHARLOTTE, NC 28217
O
ESTABLISHED PLANT SHOWN
FOR INFORMATION ONLY
GROUND
TITLE
LIVE STAKE DETAIL
NTS
FIGURE
9
NOTES
18" STANDARD (30" IF
USED AT TOE OF SLOPE)
DRAWN:
PROJ. MANAGER:
DATE:
1. DEAD STOUT STAKES SHALL BE FASHIONED FROM
UNTREATED 2" BY 4" (NOMINAL) BOARDS.
2. DEAD STOUT STAKES TO BE USED IN LIEU OF METAL
OR OTHER STAPLES OR FASTENERS FOR SECURING
EC FABRIC IN PLACE.
3. THE CONTRACTOR MAY USE'ECO-STAKE" 12" LENGTH
OR APPROVED EQUAL IN LIEU OF DEAD STOUT STAKES
FOR INSTALLATION IN THE CENTER OF THE EC FABRIC
"FIELD".
4. INSTALL EC FABRIC PER MANUFACTURER'S
INSTRUCTIONS.
GMH
JMO
5/2005
TITLE
FIGURE
H21l HILL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
DEAD STOUT STAKE
DETAIL
NTS
1o
SOIL BIOENGINEERING
DEAD STOU
TIE TO TYPICAL SECTION
NOTES:
1. INSTALL ON ALL CUT AND FILL SLOPES
AND NEAR BANK DISTURBED AREAS.
2. INSTALL PER MANUFACTURER'S
INSTRUCTIONS.
3. EC FABRIC SHALL BE WOVEN COIR
MAT WITH 50% OPEN AREA (max.), 0.5 INCH
MAX. OPENING SIZE, 4.5lbs/sq. ft. MAX.
SHEER STRESS, 10 fps MIN. VELOCITY.
OF BANK ANCHOR. TYP
SEE FIGURE 12
JND, TYP
!P.
DRAWN: GMH TITLE FIGURE
PROJ. MANAGER: JIM
DATE: 5/2005
H2 HILL®
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
EC FABRIC INSTALLATION
DETAIL 11
NTS
F:\CAD\NRCS\Cad-Details\Fig11.dwg, 05/12/2005 03:52:00 PM, PDF995 (temporary).pc3
TOP OF BANK ANCHOR
TOP OF BANK
TOE OF BANK ANCHOR
NOTES:
1. CLEAN SOIL BACKFILL SHALL BE USED TO SECURE DEAD STOUT STAKES AND
FABRIC INTO THE SOIL
2. FOR TOE OF SLOPE APPLICATIONS, FABRIC SHALL BE INSTALLED AS TO
OVERLAP TRENCH & DEAD STOUT STAKE TO POSITION THE FABRIC FOR
INSTALLATION UP THE BANKS.
3. START INSTALLATION OF EC FABRIC AT TOE OF SLOPE. WRAP FABRIC
OVER TOE OF BANK ANCHOR AND PROCEED UP THE BANK TO THE
TOP OF BANK ANCHOR
4. FOR END OF GRADING APPLICATIONS, FABRIC SHALL BE INSTALLED
PERPENDICULAR TO BANK AND ANCHORED PER TOP OF BANK DETAIL,
WITH THE EXCEPTION THAT FABRIC DOES NOT EXTEND OUTSIDE OF
TRENCH & FABRIC IS NOT EXPOSED.
DRAWN: GMH TITLE FIGURE
PROJ. MANAGER: JMO
DATE: 5/2005
EC FABRIC ANCHOR
CH2MHILL® DETAIL 12
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217 NTS
EC FABRIC
BASE FLOW
DEAD STOUT STAKE
SEE FIGURE 10
BACKFILL
MAT WRAPS OVER
TOP OF STAKE Q TOE
50' MIN.
PUBLIC STREET
EXISTING GROUND i
SOIL STABILIZATION FABRIC
UNDER 2'-3' WASHED STONE
50' MIN.'
F-
W
LLJ
OR AS SPECIFIED w
ON PLAN SHEETS N
U
J
co
a
NOTES:
1. A STABILIZED ENTRANCE PAD OF 2"- 3' WASHED STONE OR RAILROAD BALLAST SHALL BE LOCATED WHERE TRAFFIC WILL
ENTER OR LEAVE THE CONSTRUCTION SITE ONTO A PUBLIC STREET.
2. FILTER FABRIC OR COMPACTED CRUSHER RUN STONE MAY BE USED AS A BASE FOR THE CONSTRUCTION ENTRANCE.
3. THE ENTRANCE SHALL BE MAINTAINED IN A CONDITION WHICH WILL PREVENT TRACKING OR FLOWING OF SEDIMENT ONTO
PUBLIC STREETS OR EXISTING PAVEMENT. THIS MAY REQUIRE PERIODIC TOP DRESSING WITH ADDITIONAL STONE AS
CONDITIONS WARRANT AND REPAIR OR CLEANOUT OF ANY MEASURES USED TO TRAP SEDIMENT.
4. ANY SEDIMENT SPILLED, DROPPED, WASHED OR TRACKED ONTO PUBLIC STREETS MUST BE REMOVED IMMEDIATELY.
5. WHEN APPROPRIATE, WHEELS MUST BE CLEANED TO REMOVE SEDIMENT PRIOR TO ENTERING A PUBLIC STREET. WHEN
WASHING IS REQUIRED, IT SHALL BE DONE IN AN AREA STABILIZED WITH CRUSHED STONE.
DRAWN: GMH TITLE FIGURE
PROJ. MANAGER: JMO
DATE: 5/2005
STABILIZED CONSTRUCTION
CH2MHILL ENTRANCE DETAIL
4824 PARKWAY PLAZA BOULEVARD 13
SUITE 200
CHARLOTTE, NC 28217 N.T.S.
A
STE
WIRE FENCING
U
?
_z w FILTER FABRIC
° QQ.
WOVEN FILTER FABRIC n I y./ 10
o Z
I
N ?
ONE
GENERAL NOTES:
1. FILTER FABRIC FENCE SHALL BE A MINIMUM OF 32" IN WIDTH AND
SHALL HAVE A MINIMUM OF 6 LINE WIRES WITH 12" STAY SPACING.
2. WOVEN FILTER FABRIC BE USED WHERE SILT FENCE IS TO REMAIN
FOR A PERIOD OF MORE THAN 14 DAYS.
3. STEEL POSTS SHALL BE 5'-0" IN HEIGHT AND BE OF THE
SELF-FASTENER ANGLE STEEL TYPE.
4. WIRE FENCING SHALL BE AT LEAST #10 GAGE WITH A MINIMUM OF
6 LINE WIRES WITH 12" STAY SPACING.
5. TURN SILT FENCE UP SLOPE AT ENDS.
6. WIRE MESH SHALL BE MIN. 13 GAGE WITH MAXIMUM 12" OPENINGS.
7. WIRE AND WASHED STONE WILL BE REQUIRED WHEN:
AT TOE OF SLOPES GREATER THAN 10 FEET VERTICAL (2:1 SLOPE)
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
- STEEL POST
WIRE FENCING
I II\ I
`ACHOR SKIRT 6" MINIMUM
IN LIEU OF BURYING SKIRT, 6. OF
N5 WASHED STONE MAY BE USED
OVER TURNDOWN. SEE SECTION B-B.
SECTION A-A
MAINTENANCE NOTES:
1. FILTER BARRIERS SHALL BE INSPECTED BY THE FINANCIALLY
RESPONSIBLE PARTY OR HIS AGENT IMMEDIATELY AFTER EACH
RAINFALL AND AT LEAST DAILY DURING PROLONGED RAINFALL.
ANY REPAIRS NEEDED SHALL BE MADE IMMEDIATELY.
2. SHOULD THE FABRIC DECOMPOSE OR BECOME INEFFECTIVE PRIOR TO THE END
OF THE EXPECTED USABLE LIFE AND THE BARRIER STILL IS NECESSARY, THE
FABRIC SHALL BE REPLACED PROMPTLY.
3. SEDIMENT DEPOSITS SHOULD BE REMOVED WHEN DEPOSITS REACH APPROX.
HALF THE HEIGHT OF THE BARRIER. ANY SEDIMENT DEPOSITS REMAINING IN
PLACE AFTER THE SILT FENCE IS REMOVED SHALL BE DRESSED TO CONFORM
TO THE EXISTING GRADE, PREPARED AND SEEDED.
4. REMOVE SILT FENCE 1 YEAR PAST CONSTRUCTION.
%Zp
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
N.T.S.
TITLE
TEMPORARY SILT
FENCE DETAIL
FIGURE
14
STEEL POST
WIRE FENCING
i
FILTER FABRIC
N5 WASHED STONE ?
T
v= ? y?
o 6"
N Fey
T
1 ANCHOR SKIRT
6" MINIMUM
SECTION B-B
5' MAX.
BANK HEIGHT
/ STREAM CHANNEL
SURFACE FLOW
DIVERSION
STONE OVER
FILTER FABRIC
(SEE NOTE 2)
STONE APPROACH SECTION
5:1 MAX. SLOPE ON ROAD
1. USE #57 WASHED STONE
2. OMIT #57 WASHED STONE ON
CHANNEL BOTTOM IF CROSSING
A COBBLED BED STREAM.
3. REMOVE STONE AND FILTER
FABRIC AFTER CONSTRUCTION
AND TIE INTO EXISTING GRADE.
VEGETATE SITE ACCORDING TO
PLANTING PLAN.
ORIGINAL STREAMBANK
r
o
STONE OVER ' "J
FILTER FABRIC ?? °'
i
6" MIN.
r
TEMPORARY ACCESS
AS SPECIFIED BY
ENGINEER
FILTER FABRIC
DRAWN: GMH
PROJ.MANAGER: JMO
DATE: 5/2005
CH2MHILL
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, NC 28217
TITLE FIGURE
TEMPORARY STREAM
CROSSING DETAIL 15
NTS
?STAEDTLER` No. 937 811 E
Engineer's Computation Pad
/< Oa 01
sf4 Jir / i 3C?
U? 1 I
50/ 5, 1 Co.fsi uLt 4A.&r Arrs a3
' rI eGe sss?7 fo ?+`vGr? ?a .t o
?• a.•? la./ roar,, See
1
f ? /? o?@ S?oE,i ?i'1-e? G)cGeS S /bd o? .
S?r CO-1 . .SNL' JL"G^??40ra?i?/ a?Jf ei!'h
i
? G ? of
i -/
L oA?I'n../ ?rfei i ?es?re S7ei,ca..-, ?Gn/?G? Gr+?/Uk T"t-Pr-
?' Cn/moo n Co?, lCJtr'Gn O r ?O..IG1Pr
j Q, Go Il re.rrgv.,l.
wa
_ Co r77?r-v/'
f
,
Sfab;liZHG f'Vrv/ ?! S? 13H {re.-
R-1. 7 Z'nf0 Shea Ta o 13
Jvo f- to SGa/C
Source: NC Land Quality Section Figure 16
4/z rIv f
?SWEDTLER® No. 937 811 E
Engineer's Computation Pad
?i oQO1
5 0'
5/-,ki eer
C on !S trNGf!•tn //
E/Jl?vwcC ?- - - - - ?'F ?liG' L?ei7r;3 l'B?+fovn?
/eSa/?S ir! q /oss o
//?? ? ?/'Oknfi? G'OMtr? .$COliivf(yTG/'?Cy
rfaag0 ??a?., ,C/e,? i,:s Con?ral ?a // ?c
1 /? PA sa/e3 S
r ? /C G' !sr o?.a tl /T ?C?Gi ? ??rG vi ?.r? ro ?4?o J`o?? 7'`?e
t S7`/'ealn
6y...j??.fr.YCrvsJ•'^s
/if NI /COG ??> G ,C( 15, /J?.rrtr•
fti 6{
/ \ ??VT"f'Pi5 S?Or??O'' GG ??T feC?
/ /local N@drlS 1 QU? hiEa£vIt /`
? ci 3 A SeGv MO' O?f' b n ,
??3?k rGev?' ??ea5 ?.;}-titer 7 AO
Source: NC Land Quality Section Figure 17
STAEMLER® No. 937 811 E
Engineer's Computation Pad
"ev 4 Gf
CvN??i..i/rot
Cans?'•N?f 4.,,dAe/ ,?eis GS
/Iez. eSSz., / -/-a C?lveiy /?HO7?
f`7ro ,-I A4&j 1-0at, See /
/'C.?l+JF-0? moo/ ?iiit•f.'u? ,?t?u. 1.
' /"/O ?.l?L°. STa ryi ?i zec/ B C? 4.iJ N• P.r
, CCI e o-
5; rs+; f.lr f o COQ s f..,. ??•a.? C?v???o,.a?
t n may,
l srloc?. I",?C/Li?// i? ' !i!/?oi1 Co??J?t7?.bn ?? de.6r•:5
1 ? re r+rU?.c.
elect !
i
1 ?
Ar S?/•.s?r..'f Ga.r7?ro?f?'leGS?ic
O?e..
G
Zo.rC.
Je?or? ga?o:,T«- .<?'fi- Q{^??o.•r ffQ. _. 1? 1G - /S??Lr •?b:jTt' Y+ ? /Jf
,4! i S ?'rC A ?n
SaM
lVD-,L 7tv 5c•a/e-
Source: NC Land Quality Section Figure 18
4/.sS?os
o??p CHANNEL
PO
GRAVEUCOBBLE BAR
- - - - - - - - - - - -
ACTIVE CHANNEL
PLAN VIEW
(REVERSE FOR ABANDONED
CHANNEL ON OPPOSITE BANK)
EXISTING
CHANNELBED
I
2' MIN.
fi
ROCK MEDIAN
3.5' DIA. -
10' MIN.
DRAWN: GMH
PROJ. MANAGER: JMO
DATE: 5/2005
Cm HZ I L L
4824 PARKWAY PLAZA BOULEVARD
SUITE 200
CHARLOTTE, INC 28217
L
EXISTING
CHANNELBED
GRAVEL/COBBLE BAR
N TS
TITLE FIGURE
STREAM PLUG
DETAIL 19
END PLUG AT EDGE
OF ACTIVE CHANNEL
- ? FILTER FABRIC
DIMENSION
"A" MIN. -
r FLOW
ROCK MEDIAN
3.5' DIA.
KEY INTO EXIST.
BANK (3' MIN.)
FILTER FABRIC
Fir
CHING
ABAOBURYPLUGBELOW
CHANNELBED
- - - ACTIVE '
?2' MIN. CHANNEL /
SECTION A-A
NT
Organic Debris Removal
Standard Operation Procedures (SOP)
Emergency Watershed Protection (EWP) Stream Repair Projects
Buncombe County, North Carolina
SCOPE OF WORK
The work shall consist of the cleanup of designated stream areas by the removal and
disposal of trees, logs, stumps, brush, tops, rubbish, and other debris deposited in the
stream channel and floodplain by the storms of September 8 and 16, 2004.
CLEARING AND DEBRIS REMOVAL
Debris removal crews shall remove only that material which has been clearly marked by a
representative of McDowell County and/or CH2M HILL, INC (Representative) as indicated
by flagging and/or orange/red spray paint. ONLY marked debris is to be removed.
Representative cannot authorize additional work. Any work that will result in an increase in
cost must be submitted to CH2M HILL for approval prior to starting such work. In the event
that the contractor uses on-site chipping, the chipper may follow the clean-up crew along the
length of the project reach. The Contractor is responsible to properly dispose of chips.
Proper disposal may include spreading on site or removing off-site. On-site disposal requires
written approval by the property owner. Unless specifically requested to leave the chips in a
pile by a property owner the chipper shall make reasonable efforts to spread the chips as
chipping progresses.
Chippers and other heavy equipment will be staged and used at least 30-feet from the top of
the streambank or on existing paved or graveled areas prepared in accordance with standard
details described in Figure 18.
Repair of any property damage resulting from debris removal is the sole responsibility of the
Contractor.
Fallen trees, limbs and dislodged brush within the cross section of the existing or original
channel up to and including the debris line of the subject storm shall be removed. Any
foreign (man-made) debris washed in from upstream, shall be removed. Marked trees
severely undercut by stream bank erosion and trees severely leaning over the channel
whose near term fall is apparent shall be removed.
In general, Contractor clearing will be limited to the cutting of severely damaged trees
leaning across the channel, and other trees as needed to gain access for equipment to points
of channel blockage.
Disturbance of the channel bottom and banks, and equipment access areas shall be held
to the minimum necessary to allow the construction equipment to remove the debris and
shall be consistent with all state and federal permits. All areas disturbed due to debris
removal or equipment access shall be reshaped and reseeded in accordance with
standard details described in Figures 7-18.
Access to the channel will generally be perpendicular to the channel so cutting of trees is
held to a minimum with precaution taken to protect mast producing and stream canopy
trees. Un-marked dead trees that provide den habitat and are determined to pose no
hazard to the channel shall be protected. As such, the contractor will only remove marked
debris. The contractor will exercise care in the areas of existing crops to minimize
damages.
THE CONTRACTOR WILL BEAR SOLE RESPONSIBILITY FOR SELECTING THE
METHOD OF DEBRIS DISPOSAL AND THE PROPER DISPOSAL OF THE DEBRIS.
Regardless of the disposal method selected, the contractor is expected to have or obtain
knowledge of ALL aspects of the selected disposal method including, but not limited to,
associated costs and equipment, and local, State and Federal regulations. The contractor
shall obtain ANY and ALL permits for the selected disposal method and bear the cost
for the permits. Debris disposal cost shall be included in the Bidders bid. No increase in
cost will be permitted should the contractor elect to change method of disposal after the
bid is submitted. Bidders are advised that special equipment may be required for off-
site burning of debris, including, but not necessarily limited to an air curtain burner.
PROVIDED EQUIPMENT & FACILITIES
The Contractor shall provide adequate sanitary facilities for equipment operators and
work crews. Portable facilities shall be provided at the worksite and arrangements made
for proper servicing. A portable facility will be provided within 1,000 feet of the
equipment and/or work crews at all times.
COMMUNICATIONS
Each mechanized piece of equipment and each work crew shall be equipped with a two
way, battery operated radio. Radios shall be FM, have a minimum range of 5 miles.
Radios shall be maintained "on" and in the receive mode at all times while the operator is
at the site. Batteries shall be recharged overnight or as needed. An extra set of fully
charged batteries shall be maintained on board the equipment at all times. Radios shall
be equipped with clip-on hand mikes or headsets. Radios shall be maintained in good
operating condition and equipment operators shall be knowledgeable in the use and care
of the radios. Each Contractor site supervisor shall also maintain a secondary
communication system compatible with the Representative's system.
Brush Removal Guidelines
• Small diameter brush and limbs (less than four inches in diameter) that will not
cause damage if remobilized by high water will be cut into short lengths (five feet
long or less) and left in place.
All marked, dislodged or uprooted larger diameter brush will be removed from
the channel or streambank and chipped in designated areas greater than 30-feet
from the top of the bank.
• Saplings and shrubs with an intact root system are not to be removed.
Tree Removal Guidelines
• Trees will be chipped in designated areas greater than 30-feet from the top of the
streambank. Chippers and/or tub grinders may be staged on-site with written
consent from the property owner or at a central location approved by the County.
• Larger diameter trees may be pulled to the chipper using a mechanized winch
provided the process does not create excess disturbance to the streambank.
• Marked trees whose near term fall is apparent should be cut at the marked
location, which will be indicated by a painted ring around the trunk at least three-
feet above the ground surface. The root system shall not be removed from the
streambank.
• As approved by the Representative, larger diameter trees that cannot be moved
using hand equipment will be cut to manageable lengths and removed.
• The sale of chips or firewood is not allowed.
Foreign Debris and Trash Removal Guidelines
• Foreign (manmade) debris and trash will be bagged in orange trash bags where
possible.
• Filled trash bags will be removed from the channel and transported directly
offsite by the Contractor to the local landfill.
• Large debris must be loaded into a dump truck or roll-off container and
transported to the local landfill for disposal.
• Tipping fees for disposal shall be paid by the Contractor.
• Any structural debris to be removed must be separated in the following manner
for disposal: a) clean metal (e.g. mobile home frames); appliances (e.g.
washer/dryer, a/c, water heater, etc.); and household debris. Clean metal which
is deemed 'recyclable' will have no associated tipping fees.
Stream Bed and Bank Repair Guidelines
0 All temporary stream crossings shall be installed as described in Figures 15 -18.
• All Stream embankments disturbed by Contractor activities, denuded, or left bare
as a result of debris removal shall be regraded, planted, and erosion control fabric
installed as described in Figures 6, 7, and 9 -12.
• Temporary staging, chipping, and work access points shall be regraded and
grassed using a native grass/herb mix as outlined in Figures 6, 7, and 16 -18.
• Contractor shall install erosion control measures as outlined in Figures 10 -18.
SUPERINTENDENCE OF EOUIPMENT AND WORK CREWS
Any contractor providing three (3) or more pieces of equipment or five (5) or more work
crew or equipment operators shall provide a non-working crew superintendent in
addition to the required laborers and operators. The contractor shall designate in writing
the names of the crew superintendent and an alternate prior to award of the contract. The
crew superintendent shall provide on-site supervision of work crews and equipment
operators. The crew superintendent shall be responsible for the safety of work crews and
for the location and servicing of portable sanitary facilities. He/she shall be equipped
with a portable communication as specified above.
The crew superintendent shall communicate with the Representative to assure that work
crews and equipment are performing at a satisfactory level. The crew Superintendent
shall coordinate with the Representative to schedule equipment and operators for each
days work and as far in advance as possible. The superintendent shall be responsible for
keeping up with the daily operating times of all work crews and equipment and shall
maintain a log of daily equipment and work crew operations. He/she shall coordinate
daily with the Representative to concur on actual footage of streambank cleared.
WORK DIRECTION
Contractors and equipment operators will not perform activities requested or instructed
by landowners or others at the worksite, except as confirmed by the assigned
Representative.
ENVIRONMENTAL CONSIDERATIONS
Earth moving equipment will cross and operate in the stream flow only when necessary
and only when directed to do so by the Representative. Equipment shall be maintained
to prevent fuel, oil and lubricant spills in the vicinity of the stream. Refueling, repairs
and lubrication will be performed at safe distances from the stream and only at locations
approved by the Representative.
Should fuel leaks, oil leakages or hydraulic pipe rupture occur during construction, the
operators will immediately remove the equipment to a "safe" area and proceed with
repairs. The Representative will direct operators to remove equipment from the stream
whenever a leak is observed or suspected.
SAFETY
Contractor shall be responsible for the safe execution of this work and conform to all
applicable state and federal regulations. Additionally, at work sites, where equipment
will be operating on public roads, flagmen shall be stationed to warn oncoming traffic of
congestion, construction road signs shall be in place and a means of removing sediment,
mud or rocks from roadways shall be established. Residue deposited on roadways may
be removed by sweep machine, manual sweeping methods or pressurized water. The
contractor will be responsible for the implementation of these measures.
Chain saw operators will be expected to perform debris removal operations during
periods of extreme weather conditions and in areas of deep and fast moving water. The
contractor is responsible for providing the necessary equipment, clothing and other gear
to insure that laborers can perform effectively and safely under these conditions. The
Contractor shall determine if working conditions are hazardous and/or of sufficient
extreme to prevent efficient and effective operation. When such conditions exist, the
Contractor shall shut down work crews until conditions improve.
EQUIPMENT
Equipment selection to complete the work is the Contractor's responsibility.