DEQ-CFW_00003350

UNITED STATES ENVIRONMENTAL PROTECTION AGENCY
OFFICE OF POLLUTION PREVENTION AND TOXICS
REGULATION OF NEW CHEMICAL SUBSTANCES
PENDING DEVELOPMENT OF INFORMATION
In the matter of
DuPont Company
Premanufacture Notice Numbers:
P-08-508 and P-08-509
Consent Order and Determinations Supporting Consent Order
DEQ-CFW 00003350

n
TABLE OF CONTENTS
Preamble.
I. Introduction
II. Summary of Terms of the Order
M. Contents of PMNs
IV. EPA's Assessment of Exposure and Risk
V. EPA's Conclusions of Law
V1. Information Required to Evaluate Human Health and Environmental Effects
Consent Order
1. Scope of Applicability and Exemptions
E. Terms of Manufacture, Import, Processing, Distribution in Commerce, Use, and Disposal
Pending Submission and Evaluation of Information
Ill. Record -keeping
IV_ Requests for Pre -Inspection Information
V. Successor Liability Upon Transfer of Consent Order
VI. Modification and Revocation of Consent Order
VII. Effect of Consent Order
Attachment A - Definitions
Attachment B - Statistical Analysis of NCELs Analytical Method Verification Results
Attachment C - Notice of Transfer of Consent Order
DEQ-CFW 00003351

lil
I. INTRODUCTION
Under the authority of § 5(e) of the Toxic Substances Control Act ("TSCA") (15 U.S.C.
2604(e)), the Environmental Protection Agency ("EPA" or "the Agency") issues the attached
Order, regarding premanufacture notices ("PMNO) P-08-508 for the chemical substance
I and P-08-509 for the chemical
substance [
] ("the PMN substances") submitted by DuPont Company ("the Company"), to take effect
upon expiration of the PMN review period. The Company submitted the PMNs to EPA pursuant
to § 5(a)(1) of TSCA and 40 CFR Part 720.
Under § 15 of TSCA, it is unlawful for any person to fail or refuse to comply with any
provision of § 5 or any order issued under § 5. Violators may be subject to various penalties and
to both criminal and civil liability pursuant to § 16, and to specific enforcement and seizure
pursuant to § 17. In addition, chemical substances subject to an Order issued under § 5 of TSCA,
such as this one, are subject to the § 12(b) export notice requirement.
H. SUMMARY OF TERMS OF THE ORDER
The Consent Order for these PMN substances requires the Company to:
(a) submit to EPA certain toxicity and pharmacolQneties testing on the PMN substance described
in P-08-509 at least 14 weeks before manufacturing or importing a total of [ l kilograms
(kgs) of the two PMN substances (or 2 years, whichever comes later, for two of the studies) and
[ j kgs of the two PMN substances combined;
DEQ-CFW 00003352

iv
(b) require any workers who may be exposed to wear impervious gloves and distribute the PMN
substances to only those customers that agree to require impervious gloves;
(c) require any workers who may be exposed via inhalation to P-08-508 to wear a respirator with
a NIOSH Assigned Protection Factor ("APF") of 3000 and distribute to only those customers that
agree to require those respirators;
(d) require any workers who may be exposed via inhalation to P-08-509 to wear an appropriate
NIOSH-approved respirator and distribute only to customers that agree to require respirators for
any workers reasonably likely to be exposed by inhalation;
(e) as an alternative to using respirators, maintain workplace airborne concentrations of the PMN
substances in the United States at or below a specified New Chemical Exposure Limit ("NCEU )
of 0.01 mg/m3 (based on the current ACGIH TLV/TWA for the ammonium salt of
perfluorooctanoic acid ("APFO")) and distribute only to those customers in the United States that
maintain this NOEL. (To pursue this option,. a sampling and analytical method must be
developed by the Company, verified by an independent third -party laboratory, and submitted to
EPA.);
(f) for operations in the United States, recover and capture (destroy) or recycle the PMN
substances from all the process wastewater effluent streams and air emissions (point source and
fugitive) at an overall efficiency of 99% and distribute only to those customers that achieve this
percentage of efficiency or destruction;
(g) distribute the polymers containing the PMN substances (residuals) at levels not to exceed
those specified in this Order and verified using the method in Larsen et al. (2006);
and
DEQ-CFW 00003353

v
(h) maintain certain records.
III. CONTENTS OF PMN
Confidential Business Information Claims (Bracketed in the Preamble and Order}: specific
chemical identity, production volume, manufacturing process and sites, processing, use, and
other information
Chemical Identities:
Specific: P-08-508 [
CAS no.: [ ] and P-08-509 [
] CAS no. [ ].
Generic chemical identity: P-08-508—Perfluorinated aliphatic carboxylic acid and P-08-
509 Perfluorinated Aliphatic Carboxylic Acid, Ammonium. Salt
Use:
Specific: P-08-508-[
] and P-08-509-[
] Intended to replace [
Generic: P-08-508-Intermediate for polymerization aid, P-08-509-polymerization aid
Maximum 12-Month Production Volume: P-08-508-[ ] kgs, P-08-509-[ J kgs
Test Data Submitted with PMN: Physical and Chemical characteristics; Determination of the
Dissociation Constant (salt); Determination of Water Solubility and Vapor Pressure;
Biopersistence and Pharmacokinetic Screen in the Rat; In Vitro Trout Hepatocyte
DEQ-CFW 00003354

vi
Bioaccumulation Screen; Thermal Decomposition Study results
Toxicity: Acute oral toxicity, up-and-down procedure and Acute Oral Test (rats and
mice); Approximate Lethal Dose (ALD)-in rats and mice; Acute Dermal Toxicity in Rats;
Approximate Lethal Dose (ALD) by Skin Absorption -in Rabbits; Local Lymph Node Assay
(LLNA) in Mice; Acute Eye Irritation in rabbits; Acute Dermal Irritation Study in Rabbits; 7-day
Repeated Dose Oral Toxicity in Rats and Male Mice; 28-Day Repeated Dose Oral Toxicity Study
in Rats and Mice; Corrositex in vitro test; Combined Two Week Inhalation Toxicity and
Micronucleus Studies in Rats -Transformation Byproduct. In Vitro Micronucleus and
Chromosome Abberration Assay in Mouse Bone Marrow Cells; In Vitro Rat Hepatocyte Screen,
Bacterial Acute Mutation test; Determination of permeabillity coefficient (Kp) using a static in
vitro diffusion cell model; In Vitro evaluation for Chromosome Aberrations in Human
Lymphocytes -transformation byproduct
Mutagenicty test in Salmonella Typhimurium-transformation; byproduct; Combined two
week inhalation toxicity and micronucleus studies in -transformation byproduct; Water solubility,
vapor pressure, and octanol water partition coefficient and other p-chem properties of
transformation byproduct; Thermal Transformation Byproduct
Ecotoxicity/Fate: Acute toxicity to fish (Rainbow trout), daphnia, and algae; Ready
Biodegradability Study; Activated Sludge Respiration Inhibition Test; and Assessment of
Hydrolysis as a Function of pH
In general, the test substance was the salt (509), except for some acute studies,
pharmacokinetics, and mutagenicity where the test substance was both the acid (508) and the salt
(509) or as noted below. For a complete listing, see the PMN.
DEQ-CFW 00003355

vii
IV. EPA'S ASSESSMENT OF EXPOSURE AND RISK
The following are EPA 7s predictions regarding the probable toxicity, human exposure
and environmental release of the PMN substances, based on the information currently available
to the Agency.
Human Health Effects and Fate Summary:
EPA has concerns that these PMN substances will persist in the environment, could
bioaccumulate, and be toxic ("PBT")'to people, wild mammals, and birds. EPA's concerns are
based on data on the PMN substances, analogy to other [ ] chemicals, and to
perfluorooctanoic acid ("PFOA") and perfluorooctane sulfonate CTFOS") which are both.
currently under review by EPA for PBT concerns. Some [ ], PFOA, and PFOS are
expected to persist for years in the environment. Biodegradation and photolysis tests of some
analogous substances indicate little or no biodegradation or photolysis of perfluoroalkyl
compounds. Bioaccumulation concerns are based on the measured presence of certain
perfluoroalkyl compounds, including PFOA, in wildlife and in human blood samples.
Based on test data on structurally similar [ ] chemicals and data on the PMN
substances themselves, EPA has human health concerns for the PMN substances. The PMN
substances are expected to be absorbed by all routes of exposure. The PMN substances show
low acute oral toxicity (> 3400 mg/kg). The acute dermal toxicity study with P-08-509 shows
low acute dermal toxicity (>5000mg/kg). The PMN substance P-08-508 is expected to be highly
irritating or corrosive. There is high concern for eye irritation for both PMN substances.
DEQ-CFW 00003356

viii
The PMN substance P08-509 was tested in a 28-day repeated dose study in rats and mice.
In the rat study, the doses were 0, 0.3, 3, and 30 mg/kg/day in males and 0, 3, 30, and 300
mg/kg/day in females. The EPA reviewer set the NOAEL in males at 0.3 mg/kg/day based on
dose related trends and statistical significance of change in hematologic findings (decreases in
red blood cell counts, hemoglobin, and hematocrit in males), increase in clinical chemistry,
increases in absolute and relative organ/body and liver weights. Histopathologic findings in the
liver included minimal or mild hepatocellular hypertrophy in males at 3 and 30 mg/kg/day. In
this study in rats, the EPA reviewer set the NOAEL at 30 mg/kg/day in females based on
increased liver weights and liver pathology as hepatocellular hypertrophy in females given 300
mg/kg/day. The investigators concluded that the NOAELs were 30 mg/kg/day in males and 300
mg/kg/day in females, stating that all changes in treated groups are within historical control
ranges at the testing facility and as adaptive responses.
In the mouse study, the doses were 0 (vehicle control), 0.1, 3, or 30 mg/kg/day of test
substance in deionized water by gavage daily for 28 days with terminal sacrifice on day 29. In
addition, 10 male and female mice were similarly treated with 0 (vehicle control), 30 (males), or
300 (females) mg/kg/day and killed after 28 days of recovery following treatment.
The EPA reviewer set the NOAEL at 0.1 mg/kg/day based on signs of anemia and liver effects at
higher dose levels. The investigators placed the NOAEL at 0.1 mg/kg/day in males and 3 in
females.
-A related [ ] substance was also tested in a 28-day study in rats. The doses were
0, 5, 25, and 100 mg/kg/day with a NOAEL of 5 mg/kg/day and effects on the liver and kidney at
25 and 100 mg/kg/day. A single dose pharmacokinetic study was conducted in the rat and the
DEQ-CFW 00003357

MI
monkey. Male and female results were similar. Toxicity studies on some [
have shown
systemic toxicity in animals at levels as low as 0.13 mg/kg in a 90-day oral toxicity study.
Some data exists on the transformation product [ j and [ ] in combined two
week inhalation toxicity and micronucleus studies. Doses were 0, 5,000, 25,000 and 175,000
ppm. The NOAEL was determined to be 175,000 ppm. No systemic toxicity relevant to humans
was exhibited for [ ]. For [ ], increased absolute and relative liver weights
were seen in this limited study at 25,000 ppm. Mutagenicity in this study was negative.
Several mutagenicity studies were conducted on both PMN substances, P-08-508 and
509. They were not gene mutagens in two species of prokaryotes, and not inducers of DNA'
effects in mammalian cells in vivo. They were chromosome mutagens in mammalian and human
cells in culture, but not in mammals in vivo. The EPA reviewer concluded that the positive data
on the PMNs for in vitro chromosomal aberrations in mammalian and human cells are of some
concern. However, the negative responses for in vivo chromosomal effects as micronuclei and as
chromosomal aberrations, and for induction of DNA effects, alleviates that concern. No
additional mutagenicity testing is recommended.
For chronic and carcinogenic effects, no information was submitted. EPA believes that a
2-year Chronic Toxicity/Carcinogenicity study (OPPTS 870.-3491, OECD 453) is needed.
Pharmacokinetic studies were conducted in rats. Groups of 3 mate and 3 female rats were
dosed via single oral gavage with either 10 or 30 mg/kg of the PMN substance P-08-508 (98%)
and P-08-509 (84.5%). Blood samples were taken before dosing and periodically thereafter up to
168 hours (7 days) after dosing. 7n addition, fat and liver samples were taken at terminal
sacrifice. Samples were analyzed for the parent compound using HPLC/MS with a level of
DEQ-CFW 00003358

x
quantitation (LOQ) at 20 ng/ml. Clearance times were calculated for the 2 doses for males and
females as follows:
10 mg/kg (508)
30 mg/kg (508)
10 mg/kg (509)
30 mg/kg (509)
Male
28 hr
22 hr
12 hr
22 hr
Female
8 hr
4 hr
4 hr
8 hr
The Company has done some limited biomonitoring in workers and site monitoring.
EPA has reviewed the biomonitoring and concluded that samples did not take place over a long
enough period of time to see if accumulation occurred and that the limit of detection was not
sensitive enough to draw any conclusions at this time.
Toxicity studies on the analogs PFOA and PFOS indicate developmental, reproductive
and systemic toxicity in various species. Cancer may also be of concern. These factors, taken
together, raise concerns for potential adverse chronic effects in humans and wildlife. For
additional information about PFOA, consult the docket EPA-HQ-OPPT-2003-0013. Additional
information about PFOA and other perfluorinated substances may also be found in the
Administrative Record for PFOS, PFOA, and Telomers and Related Chemicals (AR-226).
Administrative Record (AR-226) is not currently available online, but copies can be requested on
CD-ROM from the EPA Docket office by calling 202/566-0280 or sending an email request to
opnt.ncic ,epa.gov.
The data on the PMN substance and some other data indicate a different and less toxic
profile for the PMN substances than for PFOA and PFOS. However, based on: 1) the
persistence of the PMN substances, 2) the toxicity of the PMN substances and some of the
] analogs, and 3) the possibility or likelihood that this substance may be used as
DEQ-CFW 00003359

xi
a major substitute for a major use of PFOA, EPA believes that more information is needed on the
toxicity and pharmacokinetics of the PMN substance P-08-509 that will be applied to the
characterization of both PMN substances.
EPA believes that additional pharmacolcinetic, reproductive, and long-term toxicological
testing on the PMN substance P-08-509 in animals is warranted. EPA will require at a certain
production volume that a modified reproductive test (OECD 421, modified) be conducted. The
modifications for the reproductive test include: (1) increase the parental sample size to 20; (2)
the duration of the study -should be extended to until the pups have reached sexual maturation; (3)
parental males should be dosed for 10 weeks prior to mating; (4) dosing of the parental animals
should be continued through lactation and then the pups should be directly dosed until they reach
sexual maturation; (5) pup body weight should be recorded on lactation days 0, 4, 7, 14, and 21
and then at weekly intervals, (6) litter size can be standardized to 4 pups/litter on lactation day 4
(optional); (7) at weaning one pup/sex/litter shall be randomly selected to follow, until sexual
maturation; and (8) the time of sexual maturation should be recorded (i.e. vaginal opening and
preputial separation). In addition, the Company will also conduct Repeated Dose
Pharmacokinetics and Metabolism testing (OPPTS 870.7485); a Combined
Carcinogenicity/Chronic Toxicity test (OPPTS 870.4300/OECD 453); and an Avian
Reproduction test (OECD 206, OPPTS 850.2300).
Environmental Effects SummMr .
EPA expects .the PMN substances to be highly persistent in the environment. In addition,
they may be bio-accumulative or biopersistent based on the predicted log Koc and because some
DEQ-CFW 00003360

xii
related substances show evidence of biopersistence. No short-term ecotoxicological concerns
were raised for the PMN substances. Reported results in acute toxicity tests in fish (rainbow
trout), Daphnia magna and green algae were: fish-96 hr LC 50>96.9 mg/l; Daphnia magna 48 hr
EC50 > 102 mg/l; and 72 hr EC50>106 mg/l. However, there is high concern for possible
environmental effects over the long-term. As stated previously, the analog PFOA is persistent in
the environment and has a long bioretention time in various species. It has been detected in a
number of species of wildlife, including marine mammals. It is toxic to mammalian and other
species. The presence in the environment and toxicological properties of PFOA continue to be
investigated. EPA believes development of additional data is warranted. EPA will require at a
certain production volume that a Fish Early Life Stage Toxicity test (OPPTS 8.50.1400), a -_
Daphnid Chronic Toxicity test (OPPTS 850.1300), and an Avian Reproduction test -Bobwhite
Quail (OPPTS 850.2300) be conducted.
Exposure and Environmental Release Summary:
These PMN substances will be manufactured by [
DEQ-CFW 00003361

]. P-08-509 will
be used as a polymerization aid in the manufacture of
Several points of exposure and release were submitted and evaluated for these PMN
substances. Doses were calculated for dermal and inhalation exposure to P-08-508 from loading
and unloading drums and sampling. Inhalation exposures are to vapors with up to 20 workers
potentially exposed. EPA estimates that these quantities could be between 3.8 mg/day (typical) to
230 mg/day (worst case). There maybe dermal exposure to a liquid containing P-08-508. For P-
08-509, manufacture and use were assumed at up to 3 sites (2 DuPont sites and one potential
customer site). According to the Company, only one site will be used at a time. At these sites, the
material will be unloaded and charged to various process vessels, such as a blend tank or a
polykettle. Due to the low vapor pressure of P-08-509, only dermal exposure was evaluated.
Based on the possibility of inadvertent exposure at low levels, the Order requires that any person
who is reasonably likely to be exposed by inhalation to the PMN substance P-08-509 to wear an
appropriate NIOSH-approved respirator. EPA has established for both PMN substances a New
Chemical Exposure Limit ("NCEL") at 0.01 mg/m3, the Threshold Limit Value ("TLV")
currently recommended for APFO by the ACGIH in the United States, in order to "level the
playing field" and allow the substitution of the PMN substance P-08-509 into the marketplace.
EPA believes that this limit should be adequate for the PMN substances based on current
information. If this ACGIH level were to change or there is data on the PMN substances that EPA
believes warrants a change, the NCEL may be changed in order to correspond with the new level
or data.
DEQ-CFW 00003362

xiv
Releases to the environment were estimated to water and to air (fugitive) and to air via
incineration. Based on submitter information, the Company currently collects the waste
containing the PMN substances and sends the waste to an off -site RCRA incinerator. In the
future, the Company intends to develop and use methods to recapture and/or recycle the
substances, but is not now doing so. EPA requires in the attached Consent Order that the
substances be recovered, recycled and/or destroyed at levels achieving 99% efficiency. EPA will
require that the Company directly sell the substances only to customers, if any, that achieve
comparable recovery or destruction. The Company shall distribute the PMN substance, P-08-509
in polymers, aqueous or solid, so that the residual P-08-508/509 cumulative total [
] are below 200 ppb level using the ASE method developed by Larsen et al. (The
Analyst 2006 p. 1105) with the level of quantification (LOQ) for the standard solution at 0.5 ppb.
If non -heat treated solid polymer is distributed then the substance cannot be further distributed,
until it is sufficiently heat treated. The Company should make every effort to minimize or prevent
any release to the environment of these substances. If dl ly new uses of the substance are found,
the Company shall find ways to recover and/or recycle the substance to comparable levels.
Fugitive releases may be of particular concern.
V. EPA'S CONCLUSIONS OF LAW
The following findings constitute the basis of -the Consent Order:
A. EPA is unable to determine the potential for human health and environmental effects from
exposure to the PMN substances. EPA therefore concludes, pursuant to § 5(e)(1)(A)(i) of TSCA,
DEQ-CFW 00003363

xv
that the information available to the Agency is insufficient to permit a reasoned evaluation of the
human health andenvironmental effects of the PMN substances.
B. In light of the potential risk of human health and environmental effects posed by the
uncontrolled manufacture, import, processing, distribution in commerce, use, and disposal of the
PMN substances, EPA has concluded, pursuant to § 5(e)(1)(A)(ii)(I) of TSCA, that uncontrolled
manufacture, import, processing, distribution in commerce, use, and disposal of the PMN
substances may present an unreasonable risk of injury to human health and the environment.
C. In light of the estimated production volume of, environmental release of, and human exposure
to, the PMN substances, EPA has farther concluded, pursuant to § 5(e)(1)(A)(ii)(R) of TSCA, that
the PMN substances will be produced in substantial quantities for a potential PBT substance, may
reasonably be anticipated to enter the environment in substantial quantities for a potential PBT
substance, and there may be significant (or substantial) human exposure to the substances.
VI. INFORMATION REQUIRED TO EVALUATE HUMAN HEALTH AND
ENVIRONMENTAL EFFECTS
Triggered Testing. The Order prohibits the Company from exceeding specified production
volumes unless the Company submits the information described in the Testing section of this
Order in accordance with the conditions specified in the Testing section.
Pended Testing. The Order does not require submission of the following information at
any specified time or production volume. However, the Order's restrictions on manufacture,
import, processing, distribution in commerce, use, and disposal of the PMN substances will
DEQ-CFW 00003364

xvi
remain in effect until the Order is modified or revoked by EPA based on submission of the
following or other relevant information.
Fate and PhysicalJChemical Properties information as follows:
Physical/Chendeal Property Testing
OPPTS or OECD Guideline
UV visible absorption
OPPTS 830.7050 or OECD 101
Hydrolysis as a function of pH
OPPTS 83 5.213 0 or OECD 111
Environmental Fate Testing
OPPTS or OECD Guideline
Modified Semi -Continuous Activated Sludge
OPPTS 835.5045, OPPTS 835.3210 or OECD
(SCAS) with Analysis for degradation
302A
products
Aerobic and Anaerobic Transformation in Soil
OECD 307
Aerobic and Anaerobic transformations in
OECD 308
Aquatic Sediment Systems
Direct Photolysis in Water (if wavelengths
OPPTS 835.2210
>290 nm are absorbed)
Indirect Photolysis in Water
OPPTS 835.5270
Phototransformation of Chemicals on Soil
OECD Jan. 2002 Draft
Surfaces
Simulation test -Aerobic Sewage Treatment
OECD 303A
(Activated Sludge Units)
Anaerobic biodegradability of organic
OECD 311
compounds in digested sludge
Fish Bioconcentration test
OPPTS 850.1730
DEQ-CFW 00003365

CONSENT ORDER
I. SCOPE OF APPLICABILITY AND EXEMPTIONS
(a) -Scope. The requirements of this Order apply to all commercial manufacturing, processing,
distribution in commerce, use and disposal of the chemical substances [
I (P-08-508) and i
I (P-08-509) ("the PMN substances")
in the United States by DuPont Company ("the Company"), except to the extent that those
activities are exempted by paragraph (b).
(b) Exemptions. Manufacturing, processing, distribution in commerce, use and disposal of the
PMN substances is exempt from the requirements of this Order (except the requirements in the
Recordkeeping and Successor Liability Upon Transfer Of Consent Order sections) only to the
extent that (1) these activities are conducted in full compliance with all applicable requirements
of the following exemptions, and (2) such compliance is documented by appropriate
recordkeeping as required in the Recordkeeping section of this Order.
(1) Export. Until the Company begins commercial manufacture of the PMN substances
DEQ-CFW 00003366

�C1
DEQ-CFW 00003367

2
for use in the United States, the requirements of this Order do not apply to manufacture,
processing or distribution in commerce of the PMN substances solely for export in accordance
with TSCA: §12(a) and (b), 40 CFR 720.3 (s) and 40 CFR Part 707. However, once the Company
begins to manufacture the PMN substances for use in the United States, no further activity by the
Company involving the PMN substances is exempt as "solely for export" even if some amount of
the PMN substances is later exported. At that point, the requirements of this Order apply to all
activities associated with the PMN substances while in the territory of the United States. Prior to
leaving U.S. territory, even those quantities or batches of the PMN substances that are destined
for export areet to terms of= the -0xder, and -count towards any production volume test
triggers in the Testing section of this Order.
(2) Research & Development ("R&D" ). The requirements of this Order do not apply to
manufacturing, processing, distribution in commerce, use and disposal of the PMN substances in
small quantities solely for research and development in accordance with TSCA §5(h)(3), 40 CFR
720.3(cc), and 40 CFR 720.36. The requirements of this Order also do not apply to
manufacturing, processing, distribution in commerce, use and disposal of the PMN substances
when manufactured solely for non-commercial research and development per 40 CFR 720.30(i)
and TSCA §5(i).
(3) Byproducts. The requirements of this Order do not apply to the PMN substances
when they are produced, without separate commercial intent, only as a "byproduct" as defined at
40 CFR 720.3(d) and in compliance with 40 CFR 720.30(g).
(4) No Separate Commercial Purpose. The requirements of this Order do not apply to
the PMN substances when they are manufactured, pursuant to any of the exemptions in 40 CFR
DEQ-CFW 00003368

720.30(h), with no commercial purpose separate from the substance, mixture, or article of which
it is a part.
(5) Imported Articles. The requirements of this Order do not apply to the PMN
substances when they are imported as part of an "article" as defined at 40 CFR 720.3(c) and in
compliance with 40 CFR 720.22(b)(1).
(c) Automatic Sunset. If the Company has obtainedfor the PMN substances a Test Market
Exemption ("TME") under TSCA §5(h)(1) and 40 CFR 720.38 or a Low Volume Exemption
("LVE") or Low Release and Exposure Exemption ("LoREX") under TSCA §5(h)(4) and 40
CFR 723.50(c)(1) and (2) respectively, any such exemption is automatically rendered null and
void as of the effective date of this Consent Order.
II. TERMS OF MANUFACTURE, IMPORT, PROCESSING,
DISTRIBUTION IN COMMERCE, USE, AND DISPOSAL
PENDING SUBMISSION AND EVALUATION OF INFORMATION
PROHIBITION
The Company is prohibited from manufacturing, importing, processing, distributing in
commerce, using, or disposing of the PMN substances in the United States, for any nonexempt
commercial purpose, pending the development of information necessary for a reasoned
evaluation of the human health and environmental effects of the substance, and the completion of
EPA's review of, and regulatory action based on, that information, except in accordance with the
conditions described in this Order. -
DEQ-CFW 00003369

W
TESTING
(a) Section 8(e) Reporting. Any information on the PAIN substances which reasonably supports
the conclusion that the PMN substances presents a substantial risk of injury to health or the
environment required to be reported under EPA's section 8(e) policy statement at 43 Federal
Reg'ster 11110 (March 16, 1978) as amended at 52 Federal Regis, teT 20083 (May 29, 1987), shall
reference the appropriate PMN identification number for this substance and shall contain a
-statement that the substance is subject to this Consent Order. Additional information regarding
section 8(e) reporting requirements can be found in the reporting guide referenced at 56 Federal
Register 28458 (June 20, 1991).
(b) Notice of Study Scheduling. The Company shall notify, in writing, the EPA Laboratory Data
Integrity Branch (2225A), Office of Enforcement and Compliance Assurance, U.S.
Environmental Protection Agency, 1200 Pennsylvania Avenue, N.W., Washington, D.C. 20460,
of the following information within 10 days of scheduling any study required to be performed
pursuant to this Order, or within 15 days after the effective date of this Order, whichever is later:
(1) The date when the study is scheduled to commence;
(2) The name and address of the laboratory which will conduct the study;
(3) The name and telephone number of a person at the Company or the laboratory whom
EPA may contact regarding the study, and
(4) The appropriate PMN identification number for each substance and a statement that
the substance is subject to this Consent Order.
DEQ-CFW 00003370

5
(c) Good Laboratory Practice Standards and Test Protocols. Each study required to be
performed pursuant to this Order must be conducted according to TSCA Good Laboratory
Practice Standards at 40 CPR Part 792 and using methodologies generally accepted in the
relevant scientific community at the time the study is initiated. Before starting to conduct any
such study, the Company must obtain approval of test protocols from EPA by submitting written.
protocols. EPA will respond to the Company within 4 weeks of receiving the written protocols.
Published test guidelines specified in paragraph (d) provide general guidance for development of
test protocols, but are not themselves accepfable-protocols. Approval of the test protocol does
not mean pre -acceptance of test results. Because the Chronic Daphnid Toxicity study and the
90-day toxicity study enumerated below were begun before the execution of this Order the
requirement for submission and approval of the protocols for these two studies only is waived.
(d) Triggered Testing Requirements. (i) The Company is prohibited from manufacturing or
importing the PMN substances beyond the following aggregate manufacture and import volumes
of both PMN substances combined ("the production limits"), unless the Company conducts the
following studies and submits all final reports and underlying data in accordance with the
conditions specified in this Testing section.
Production Limit
[ ] kilograms
Study
1) Repeated dose
Metabolism and
Pharmacokinetics
rats and mice
2) Modified 1-generation
Reproduction study
Guideline
OPPTS 870.7485
OECD 421, modified, per
(iv) below
DEQ-CFW 00003371

no
3) Avian Reproduction -Bobwhite
Quail
4). Fish Early Life Stage
Toxicity
5) Daphnid Chronic Toxicity
OPPTS 850.2300
OPPTS 850.1400
OPPTS 850.1300
*An alternate Production Limit for studies 1 and 2 only is two years from the date of
commencement of nonexempt commercial manufacture of either PMN substance, or [
kilograms, whichever comes later.
] kilograms 6) 90-day toxicity study
7) Chronic toxicity/
carcinogenicity study
OPPTS 870.3100 (OECD 408)
OPPTS 870.4300 (OECD 453)
(ii) the test substance shall be the substance described in P-08-509;
(iii) EPA recommends that the Company conduct the pharmacokinetics testing first to
confirm species acceptability and to provide a reliable half-life for these substances;
(iv) The modifications for the 1-generation reproduction study (study 2 above) are: 1)
increase the parental sample size to 20; 2) the duration of the study shall be extended to until the
pups have reached sexual maturation; 3) parental males shall be dosed for 10 weeks prior to
mating; 4) dosing of the parental animals shall be continued through lactation and then the pups
should be directly dosed until they reach sexual maturation; 5) pup body weight shall be recorded
on lactation days 0, 4, 7, 14, and 21 and then at weekly intervals; 6) litter size can be
DEQ-CFW 00003372

7
standardized to 4 pups/litter on lactation day 4 (optional); 7) at weaning one pup/sex/litter shall
be randomly selected to follow until sexual maturation; and 8) the time of sexual maturation shall
be recorded (i.e. vaginal opening and preputial separation).
(e) Test Reports. The Company shall: (1) conduct each study in good faith, with due care, and
in a scientifically valid manner; (2) promptly furnish to EPA the results of any interim phase of
each study; and (3) submit, in triplicate (with an additional sanitized copy, if confidential
business information is involved), the final report of each study and all underlying data ("the
report and data") to EPA no later than 14 weeks prior to exceeding the applicable production
limit. The final report shall contain the contents specified in 40 CFR 792.185, Underlying data.
shall be submitted to EPA in accordance with the applicable "Reporting", "Data and Reporting`",
and "Test Report" subparagraphs in the applicable test guidelines. However, for purposes of this
Consent Order, the word "should" in those subparagraphs shall be interpreted to mean "shall" to
make clear that the submission of such information is mandatory. EPA will not require the
submission of raw data such as slides and laboratory notebooks unless if EPA finds, on the basis
of professional judgment, that an adequate evaluation of the study cannot take place in the
absence of these items.
(f) Testing Waivers. The Company is not required to conduct a study specified in paragraph (d)
of this Testing section if notified in writing by EPA that it is unnecessary to conduct that study.
(g) Equivocal Data. If EPA finds that the data generated by a study are scientifically equivocal,
DEQ-CFW 00003373

0
the Company may continue to manufacture and import the PMN substances beyond the
applicable production limit. To seek relief from any other restrictions of this Order, the.
Company may make a second attempt to obtain unequivocal data by reconducting the study
under the conditions specified in paragraphs (b), (c), and (e)(1) and (2). The testing requirements
may be modified, as necessary to permit a reasoned evaluation of the risks presented by the PMN
substances, only by mutual consent of EPA and the Company.
(h) EPA Determination of Invalid Data.
(1) Except as described in subparagraph (h)(2), if, within 6 weeks of EPA's receipt of a
test report and data, the Company receives written notice that EPA finds thatthe-.data generated
by a study are scientifically invalid, the Company is prohibited from further manufacture and
import of the PMN substances beyond the applicable production limit.
(2) The.Company may continue to manufacture and import the PMN substances beyond
the applicable production limit only if so notified, in writing, by EPA in response to the
Company's compliance with either of the following subparagraphs (h)(2)(i) or (h)(2)(ii).
(i) The Company may reconduct the study in compliance with paragraphs (b), (c),
and (e)(1) and (2). If there is sufficient time to reconduct the study and submit the report and
data to EPA at least 14 weeks before exceeding the production limit as required by subparagraph
(e)(3), the Company shall comply with subparagraph (e)(3). If there is insufficient time for the
Company to comply with subparagraph (e)(3), the Company may exceed the production limit and
shall submit the report and data in triplicate to EPA within a reasonable period of time, all as
specified by EPA in the notice described in subparagraph (h)(1). EPA will respond to the
DEQ-CFW 00003374

6
Company, in writing, within 6 weeks of receiving the Company's report and data.
(ii) The Company may, within 4 weeks of receiving from EPA the notice
described in subparagraph (h)(1), submit to EPA a written report refuting EPA's finding. EPA
will respond to the Company, in writing, within 4 weeks of receiving the Company's report.
(i) Company Determination of Invalid Data.
(1)Except as described in subparagraph (i)(2), if the Company becomes aware that
circumstances clearly beyond the control of the Company or laboratory will prevent, or have w
prevented, development of scientifically valid data under the conditions specified in paragraphs
(c) and (e), the Company remains prohibited from further manufacture and import of the PMN
substances beyond the applicable production limit.
(2) The Company may submit to EPA, within 2 weeks of first becoming aware of such
circumstances, a written statement explaining why circumstances clearly beyond the control of
the Company or laboratory will cause or have caused development of scientifically invalid data.
EPA will notify the Company of its response, in writing, within 4 weeks of receiving the
Company's report. EPA's written response may either:
(i) allow the Company to continue to manufacture and import the PMN
substances beyond the applicable production limit, or
(ii) require the Company to continue to conduct, or to reconduct, the study in
compliance with paragraphs (b), (c), and (e)(1) and (2). If there is sufficient time to conduct or
reconduct the study and submit the report and data to EPA at least 14 weeks before exceeding the
production limit as required by subparagraph (e)(3), the Company shall comply with
DEQ-CFW 00003375

10
subparagraph (e)(3). If there is insufficient time for the Company to comply with subparagraph
(e)(3), the Company may exceed the production limit and shall submit the report and data in
triplicate to EPA within a reasonable period of time, all as specified by EPA in the notice
described in subparagraph (i)(2). EPA will respond to the Company, in writing, within 6 weeks
of receiving the Company's report and data, as to whether the Company may continue to
manufacture and import beyond the applicable production limit.
0) Unreasonable Risk.
(1) EPA may notify the Company in writing that EPA finds that the data generated by a
study are scientifically valid and unequivocal and indicate that, despite the terms of this Order,
the PMN substances will or may present an unreasonable risk of injury to human health or the
environment. EPA's notice may specify that the Company undertake certain actions concerning
further testing, manufacture, import, processing, distribution, use and/or disposal of the PMN
substances to mitigate exposures to or to better characterize the risks presented by the PMN
substances. Within. 2 weeks from receipt of such a notice, the Company must cease all
manufacture, import, processing, distribution, use and disposal of the PMN substances, unless
either:
(2) within 2 weeks from receipt of the notice described in subparagraph 6)(1), the
Company complies with such requirements as EPA's notice specifies; or
(3) within 4 weeks from receipt of the notice described in subparagraph 6)(1), the
Company submits to EPA a written report refuting EPA's finding and/or the appropriateness of
any additional requirements imposed by EPA. The Company may continue to manufacture,
DEQ-CFW 00003376

11
import, process, distribute, use and dispose of the PMN substances in accordance with the terms
of this Order pending EPA's response to the Company's written report. EPA will respond to the
Company, in writing, within 4 weeks of receiving the Company's report. Within 2 weeks of
receipt of EPA's written response, the Company shall comply with any requirements imposed by
EPA's response or cease all manufacture, import, processing, distribution, use and disposal of the
PMN substances.
(k) Other Requirements. Regardless of the satisfaction of any other conditions in this Testing
section, the Company must continue to obey all the terms of this Consent Order until otherwise
notified in writing by EPA. The Company may, based upon submitted test data or other relevant
information, petition EPA to modify or revoke provisions of this Consent Order pursuant to Part
VI. of this Consent Order.
PROTECTION IN THE WORKPLACE
(a) Establishment of Program. During manufacturing, processing, and use of the PMN
substances at any site controlled by the Company (including any associated packaging and
storage and during any cleaning or maintenance of equipment associated with the PMN
substances), the Company must establish a program whereby:
(1) General Dermal Protection. Each person who is reasonably likely to be dermally
exposed in the work area to the PMN substances through direct handling of the substance or
through contact with equipment on which the substance may exist, or because the substance
DEQ-CFW 00003377

12
becomes airborne in a form listed in subparagraph (a)(5) of this section, is provided with, and is
required to wear, personal protective equipment that provides a barrier to prevent dermal
exposure to the substance in the specific work area where it is selected for use. Each such item
of personal protective equipment must be selected and used in accordance with Occupational
Safety and Health Administration ("OSHA") dermal protection requirements at 29 CFR
1910.132, 1910.133, and 1910.138.
(2) Specific Dermal Protective Equipment. The dermal personal protective equipment
required by subparagraph (a)(1) of this section must include, but is not limited to, the following
items:
(i) Gloves.
(ii) Full body chemical protective clothing.
(iii) Chemical goggles or equivalent eye protection.
(iv) Clothing which covers any other exposed areas of the arms, legs and torso.
Clothing in this subparagraph (a)(2)(iv) need not be tested or evaluated under the requirements of
subparagraph (a)(3)
(3) Demonstration of Imperviousness. The Company is able to demonstrate that each
item of chemical protective clothing selected, including gloves, provides an impervious barrier to
prevent dermal exposure during normal and expected duration and conditions of exposure within
the work area by any one or a combination of the following:
(i) Permeation Testing. 'Testing the material used to make the chemical protective
clothing and the construction of the clothing to establish that the protective clothing will be
impervious for the expected duration and conditions of exposure. The testing must subject the
DEQ-CFW 00003378

13
chemical protective clothing to the expected conditions of exposure, including the likely
combinations of chemical substances to which the clothing maybe exposed in the work area.
Permeation testing shall be conducted according to the American Society for Testing and
Materials ("ASTM") F739 "Standard Test Method for Resistance of Protective Clothing
materials to Permeation by Liquids or Gases." Results shall be recorded as a cumulative
permeation rate as a function of time (or versus time), and shall be documented in accordance
with AS TM F739 using the format specified in ASTM F1194-99 "Guide for Documenting the
Results of Chemical Permeation Testing on Protective Clothing Materials." Gloves may not be
used for a time period longer than they are actually tested and must be replaced at the end of each
work shift during which they are exposed to the PMN substances.
(ii) Manufacturer's Specifications. Evaluating the specifications from the
manufacturer or supplier of the chemical protective clothing, or of the material used in
construction of the clothing, to establish that the chemical protective clothing will be impervious
to the PMN substances alone and in likely combination with other chemical substances in the
work area.
(4) Respiratory Protection. Each person who is reasonably likely to be exposed by
inhalation in the work area to the PMN substance, P-08-508, in the form listed in subparagraph
(a)(5) of this section, is provided with, and is required to wear, at a minimum, a NIOSH-certified
respirator with an Applied Protection Factor ("APF") of 3000 from the respirators listed in
subparagraph (a)(6) of this section. All respirators must be used in accordance with OSHA and
NIOSH respiratory protection requirements at 29 CFR 1910.134 and 42 CFR Part 84. All
respirators must be issued, used, and maintained according to an appropriate respiratory
DEQ-CFW 00003379

14
protection program under the OSHA requirements in 29 CFR 1910.134.
In addition, each person who is reasonably likely to be exposed by inhalation in the work
area to the PMN substance P-08-509 must be provided with and wear an appropriate NIOSH-
approved respirator.
(5) Physical States. The following physical states of airborne chemical substances are
listed for subparagraphs (a)(1) and (4) of this section:
(i) Particulate (including solids or liquid droplets),
(ii) Gas/vapor_(all substances in the gas form), or
(iii) Combination GasNapor and Particulate (gas and liquid/solid physical states
are both present; a good example is paint spray mist, which contains both liquid droplets and
vapor).
(6) Authorized Respirators. The following NIOSH-certified respirators meet the
minimum requirements for P-08-508 in subparagraph (a)(4) of this section:
—a NIOSH-certified supplied -air respirator operated in pressure demand or other positive
pressure mode and equipped with a tight -fitting full face piece.
NEW CIIEIIMICAL EXPOSURE LEMT
(a) Alternative to Requirements of Respirator Section.
(1) EPA recommends and encourages the use of pollution prevention, source reduction,
engineering controls and work practices, rather than respirators, as a means of controlling
inhalation exposures whenever practicable.
(2) Whenever a person is reasonably likely to be exposed to the PMN substances by
DEQ-CFW 00003380

15
inhalation, as an alternative to compliance with the respirator requirements in the Protection in
the Workplace section of this Order, the Company may comply with the requirements of this
New Chemical Exposure Limit section. However, before the Company may deviate from the
respirator requirements in the Protection in the Workplace section of this Order, the Company
must:
(i) submit to EPA a copy of the Company's sampling and analytical method for
the PMN substances, verified in accordance with subsection (c)(3) of this New Chemical
Exposure Limit section;
(ii) obtain exposure monitoring results in accordance with this New Chemical
Exposure Limit section; and
(iii) based on those exposure :monitoring results, select, provide, and ensure use if
necessary of the appropriate respiratory protection specified in paragraph (e)(2) of this New
Chemical Exposure Limit section by persons who are reasonably likely to be exposed to the
PMN substances by inhalation.
(3) After appropriate respiratory protection has been selected at a workplace based on the
results of actual exposure monitoring conducted in accordance with this New Chemical Exposure
Limit section, the Company shall not, at that workplace, use the respiratory protection required in
the Protection in the Workplace section of this Oder (unless it is the same as required by this
New Chemical Exposure Limit section).
(b) Exposure Limit.
(1) General. The following new chemical exposure limit ("NCEU) for the PMN
DEQ-CFW 00003381

M
substances is an interim level determined by EPA based on the limited information available to
the Agency at the time of development of this Order. The NCEL for the PMN substances is as
follows:
(i) Time -Wei ted Average "TWA" Limit. The Company shall ensure that no
person is exposed to an- airborne concentration of both PMN substances combined in excess of
0.01 mg/m3 (the NCEL) as an 8-hour time -weighted average, without using a respirator in
accordance with subsection (e) of this New Chemical Exposure Limit section.
(ii) Non-8-Hour Work -shifts. For non-8-hour work -shifts, the NCEL for that
work -shift ("NCELn") shall be determined by the following equation: NCELn = NCEL x (8/n) x
[(24-n)/l6], where n = the number of hours in the actual work -shift.
(2) Automatic Sunset. If, subsequent to the effective date of this Order, OSHA
promulgates, pursuant to §6 of the Occupational Safety and Health Act, 29 U.S.C. 655, a final
chemical -specific permissible exposure limit ("PEL') specifically applicable to these PMN
substances and the OSHA PEL is not challenged in court within 60 days of its promulgation, then
any respirator requirements in the Protection in the Workplace section of this Order and any
requirements of this New Chemical Exposure Limit section applicable to workers and situations
subject to the OSHA PEL sball automatically become null and void. However, the requirements
of this Consent Order are not negated by any pre-existing OSHA PEL applicable to the PMN
substances.
(c) Performance -Criteria for Sampling and Analytical Method.
(1) Applicability. For initial .development and validation of the sampling and analytical
DEQ-CFW 00003382

17
method for the PMN substances, all the -requirements of this subsection (c) apply. For
subsequent exposure monitoring conducted pursuant to subsection (d) of this New Chemical
Exposure Limit section, only the following requirements apply: (c)(4)(i), (4)(h), (4)(iv)(11),
(4)(v)(H), (8), (9), and (10). Any deviation from the requirements of this subsection (c) must be
approved in writing by EPA.
(2) Submission of Verified Method and Certification Statement. The Company shall
submit to EPA a copy of a validated sampling and analytical method for the PMN substances
which satisfies the criteria specified in this subsection (c). The method description shall
expressly state how the method compares with each quantitative requirement specified in this
subsection (c). The submission must include a written statement, signed by authorized officials
of both the Company and the Laboratory, certifying the truth and accuracy of the independent
laboratory verification conducted pursuant to subsection (c)(3). To assist EPA in identifying the
document, it shall state in a conspicuous, underlined subject -line at the top of the first page:
"NCEL Samnl nng and Analytical Method for PMN # ," after -which the correct PMN
number for this chemical substance shall be stated.
(3) Verification of Analytical Method by independent Third -Party Laboratory.
(i) Verification. The Company shall have an independent reference laboratory
("Laboratory") verify the validity of the analytical method for the PMN substances, in accordance
with the other requirements in this subsection (c)(3). 1t is the Company's responsibility to ensure
that the Laboratory complies with all the requirements specified in this subsection (c)(3).
(ii) independent Reference LaboxatoiY. The independent reference laboratory
must be a separate and distinct person (as defined at 40 CFR 720.3 (x)) from the Company and
DEQ-CFW 00003383

from any other person who may have developed the method for the Company.
(iii) Accreditation. The Laboratory must be accredited by a formally recognized
government or private laboratory accreditation program for chemical testing and/or analysis.
(iv) Good Laboratory Practice Standards. The Laboratory verification of the
analytical method for the PMN substances must comply with TSCA Good Laboratory Practice
Standards ("GLPS") at 40 CFR Part 792. (Certain provisions of the TSCA GLPS applicable to
toxicity testing in laboratory animals, such as 40 CFR 792.43 ("Test system care facilities"),
792.45 ("Test system supply facilities") and 792.90 ("Animal and other test system care"), are
clearly inapplicable to the NCEL requirements.) However, compliance with TSCA GLPS is not
required under this New Chemical Exposure Limit section where the analytical method is
verified by a laboratory accredited by either: (A) the American Industrial Hygiene Association
("AIHA") Industrial Hygiene Laboratory Accreditation Program ("IHLAP"); or (B) another
comparable program approved in advance in writing by EPA.
(v) Analysis of Duplicate Samples. The Company shall collect six duplicate
samples (a total of 12) at the TWA coincentration. The samples shall be taken either from a
controlled environment (e.g., a sealed chamber or "glove box") which closely resembles the
actual workplace conditions or, for solids and liquids with very low vapor pressure, by injecting
the PMN substances onto a sample collection device. The duplicate samples shall be collected
on identical collection media, at the same time, and under the same conditions. One set of six
samples shall immediately be analyzed by the Company, the other set of six samples shall be
analyzed by the Laboratory using the method developed by or for the Company.
(vi) Sample Storage Study., If the results of the analysis of duplicate samples
DEQ-CFW 00003384

19
pursuant to paragraph (c)(3)(v) do not satisfy the requirements in paragraph (c)(3)(vii), the
Company must perform a sample storage study as follows:
(1) Triplicate Samples. The Company shall collect six triplicate samples
(a total of 18) at the TWA concentration. The samples shall be taken either from a controlled
environment (e.g., a sealed chamber or "glove box") which closely resembles the actual
workplace conditions or, for solids and liquids with very low vapor pressure, by injecting the
PMN substances onto a sample collection device. The triplicate samples shall be collected on
identical collection media, at the same time, and under the same conditions. One set of six
samples shall immediately be analyzed by the Company.
(B) Analysis After &nple Storage. A sample storage evaluation shall be
performed with the two remaining sets of six samples. One set of six samples shall be analyzed
by the Laboratory using the method developed by or for the Company, and the other shall be
analyzed by the Company on the same day as the Laboratory analyzes its six samples..
Specialized storage conditions for the samples including extraction conditions, time from
sampling to extraction, time from collection or extraction (if applicable) to analysis and storage
conditions must be specified in the method description.
(vii) Comparison of Results. The difference between the results of the two sets of
six samples analyzed by the Laboratory and the Company as required in either paragraph
(c)(3)(v) or (c)(3)(vi)(11) shall be evaluated using a two -sample t-test with unequal variances, and
the two sides of the critical regions shall not exceed a 5% significance level. (See Attachment B
- Statistical Analysis of NCELs Analytical Method Verification Results.) The arithmetic mean of
each set of six samples must be within 10% of the overall arithmetic mean of the two sets of
DEQ-CFW 00003385

20
sample measurements. If the arithmetic mean of each set of six samples is not within 10% of the
overall arithmetic mean, then the sample storage time between collection and analysis must be
reduced until the average of each set of six samples is within 10% of the overall arithmetic mean.
(4) Accuracy. The sampling and analytical method must clearly demonstrate the
following:
(i) General. The sampling and analytical method, and all exposure monitoring
data relied on by the Company, shall be accurate to within +25% at a 95% confidence level for
concentrations of the PMN substances ranging from one half the NCEL to twice the NCEL.
(ii) NCEL Quantitation Limits. The analytical method should be capable of
reliably quantifying the PMN substances across the full range of reasonably likely exposures. At
a minimum, the analytical method must be capable of reliably quantifying from a lower
quantitation limit ("LQL") of one half the NCEL to an upper quantitation limit ("UQL") of at
least twice the NCEL. If the Company obtains an exposure monitoring sample that is more than
10% above the actual UQL of the analytical method, the Company must comply -with paragraph
(e)(4)(i).
(iii) Lower Quantitation Limit Signal -To -Noise Ratio. The analytical method
shall be capable of quantifying the PMN to a concentration of one half the NCEL with a signal
that is at least five times the baseline noise level. Baseline noise must be amplified to a
measurable level when possible, even if the required amplification is beyond that used in routine
analysis of samples. (If baseline noise cannot be obtained, another reference must be selected.
This may be a peak considered to be noise caused by the reagent matrix.) The sampling
preparation method must be specified and the detection limit for the analytical procedure must be
DEQ-CFW 00003386

21
reported as mass per injection for chromatographic techniques.
(iv) Instrument Calibration.
(1) Initial Calibration. For method development and validation (but not
subsequent exposure monitoring), the initial calibration shall at a minimum consist of five (5)
calibration standards with a linear correlation of 0.95 -- these five (5) calibration standards must
consist of one standard at each of the following concentrations: one half the NCEL (0.5 x
NOEL); between one half and one times the NCEL (0.5 x NCEL < > 1 x NCEL); one times the
NCEL (1 x NOEL); between one and two times the NCEL (1 x NCEL < > 2 x NOEL), and twice
the NCEL (2 x NCEL).
(11) Continuing Calibration. During each week of both method
development/validation and subsequent exposure monitoring, the Company shall conduct both an
initial instrument calibration and a continuing calibration. The Company shall perform at least
one continuing calibration sample at the NCEL concentration, and at least one additional
calibration sample per every 10 samples analyzed. The continuing calibration sample shall fall
within + 25% of the initial calibration value. If not, then the initial calibration must be repeated,
and any samples associated with that outlying calibration check must be re -analyzed.
(v) Calculated Percent Recavery.
(1) Initial Calculation. For method development and validation, the
Company must calculate the percent of the PMN substances recovered by the analytical method
from a sample containing a known quantity of the PMN substances. The sample shall be taken
either from a controlled environment (e.g., a sealed chamber or "glove box") which closely
resembles the actual workplace conditions or, for solids and liquids with very low vapor
DEQ-CFW 00003387

22
pressure, by injecting the PMN substances onto a sample collection device. (Such a sample is
referred to as a "matrix spike"). The calculated percent recovery for each matrix spike shall be
greater than or equal to 75% and less than or equal to 125°%. Spike concentrations for the PMN
substances must be included in the sampling and analytical method submitted to EPA.
(1) Subsequent Calculation. During each subsequent exposure monitoring
episode or campaign, at least 1 matrix spike, prepared by injecting the PMN substances onto a
sample collection device, shall be analyzed. (This matrix spike must be prepared at the NCEL
concentration.)
(vi) Sampling Device Capacity. The capacity of the sampling device must be
tested and results reported to show under a known and well-defined set of conditions that the
device is capable of collecting the new chemical in solid, liquid or vapor phase with minimal
loss. The sampling device's capacity (air volume and collected analyte mass) must be specified.
For, methods that use adsorbent tubes as the collection medium, evidence of the capacity must be
provided in the form of breakthrough testing. This testing must be done at a concentration twice
the NCEL and under conditions similar to those expected in the workplace. Breakthrough is
defined to have occurred when the concentration of the PMN substances in the effluent stream is
equal to 5% of the concentration of the influent stream, or when 20% of the PMN substances is
detected in the backup section of the sampler.
(vii) Sampling Device Desorption Efficiency. Where applicable, the desorption
efficiency must be evaluated for the air sampling device. A minimum of six air samples spiked
with the PMN substances at least the NCEL concentration must be prepared. A recovery of at
least 75% must be obtained for each of the six samples.
DEQ-CFW 00003388

23
(5) Precision. The estimate of the coefficient of variation of each set of six samples from
the controlled atmosphere test (spiked at 1.0 NCEL, per paragraphs (c)(3)(v) or (vi)) must be less
than 0.105, including allowance of 0.05 for error due to sampling.
(6) Intemretation of Accuracy and Precision Data.
(i) If a single matrix spike recovery is less than 75% recovery or greater than
125% or the estimated coefficient of variation is greater than 0.105, then the Company must re -
prepare the matrix spike, re -sample, and re -analyze all samples associated with such matrix spike
or triplicate samples.
(ii)- For percent recoveries less than 90% but greater than 75%, correction for low
recovery is required. Correct for recovery first by dividing the observed amount by the
proportion recovered before determining if measurements fall below the NCEL. For example, if
the observed level is 30 mg/m3 and the percent recovery is 75%, use the value 30 mg&/(0.75)
40 mg& when determining whether the levels are below the exposure limit.
- (7) Representativeness. All sample conditions used to develop the methodology shall
mimic the actual workplace environment expected to be monitored. Conditions such as the
temperature, humidity, lighting, and presence of other chemicals, etc. must mimic the conditions
in the workplace to be monitored.
(8) Changes Affecting Validity. If the workplace environment changes from the initial
conditions described in the verified sampling and analytical method in a way reasonably likely to
invalidate the accuracy of the method, then the Company must comply with the respirator
requirements in the Protection in the Workplace section of this Order, unless the Company re-
validates the method to confirm that the requirements for accuracy and precision in paragraphs
DEQ-CFW 00003389

24
(c)(4) and (5) are met. ExaY aples of possible changes include but are not limited to: introduction
of a new chemical substance to- the workplace which may interfere with the analysis of the new
chemical; introduction of light to the workplace which may interfere with light-sensitive PMN
substances; or introduction of water/increased humidity to the workplace which could react with
the PMN substances and cause difficulties in collection and analysis.
(9) Comparability. All data and results shall be reported in the same units of
measurement as the NOEL.
(10) Responsibility for Method Validity. The independent laboratory verification and
EPA receipt of the sampling and analytical method pursuant to this subsection (c) do not ensure
that the method will produce valid exposure monitoring data. The Company is ultimately
responsible for ensuring the validity of its exposure monitoring data.
.(d) Monitoring Potential Ex osure.
(1) General.
(i) Action Level. The "action level" is defined as an airborne concentration of the
PMN substances, calculated as an 8-hour time -weighted average, equal to one half the NCEL
TWA specified in subparagraph (b)(1). For non-8-hour work shifts, the action level is equal to
one half the NCELn. (The NCELn is described in subparagraph (b)(1)(ii).) The Company may
exceed the action level without penalty. The purpose of the action level is solely to determine the
requisite monitoring frequency.
(ii) Representative Exposure Groups. Whenever exposure monitoring is required
by this New Chemical Exposure Limit section, the Company shall take representative samples of
DEQ-CFW 00003390

25
what the potential exposure of each person who is reasonably likely to be exposed to airborne
concentrations of the PMN substances would be if respirators were not worn. The Company
shall do so by sampling the breathing zone air'of at least one person that represents, and does not
underestimate, the potential exposure of every person performing the same or substantially
similar operations in each work shift, in each job classification, in each work area (hereinafter
identified as an "exposure group") where inhalation exposure to the PMN substances is
reasonably likely to occur. The exposure of each person need not be itself directly sampled if
that exposure is represented by sampling the exposure of another person in the same exposure
group.
(iii) Good Laboratory Practice Standards. Determinations ofpotential inhalation
exposure shall be made according to TSCA Good Laboratory Practice Standards at 40 CFR Part
792 and the sampling and analytical method developed pursuant to subsection (c) of this New
Chemical Exposure Limit section. [Certain provisions of the TSCA GLPS applicable to toxicity
testing in laboratory animals, such as 40 CFR 792.43 ("Test system care facilities"), 792.45
('Test system supply facilities") and 792.90 ("Animal and other test system care"), are clearly
inapplicable. to,the.NCTL requirements,.] However, co npliance,with TSCA GLPS is not
required where exposure monitoring samples are analyzed by a laboratory accredited by either:
(A) the American Industrial Hygiene Association ("AIHA") Industrial Hygiene Laboratory
Accreditation Program ("IHLAP"); or (B) another comparable program approved in advance in
writing by EPA.
(iv) Full Shift Exposure Samples. Representative 8-hourTWAairborne
concentrations shall be determined on.the basis -!of samples representing the full shift exposure for
DEQ-CFW 00003391

26
each exposure group.
(2) Initial Monitoring. Before the Company may deviate from the respirator
requirements of the Protection in the Workplace section, the Company shall conduct initial
exposure monitoring to accurately determine the airborne concentration of the PMN substances
for each exposure group in which persons are reasonably likely to be exposed to the PMN
substances.
(3) Periodic Monitoring.
(i) If any representative samples taken during the initial exposure monitoring
reveal an airborne concentration at or above the action level but at or below the TWA, the
Company shall repeat the exposure monitoring for that exposure group at least every 6 months. .
If the PMN substances are not manufactured, processed, or used at all during a given 6 month
calendar period, the Company is not required to conduct exposure monitoring until manufacture,
processing, or use of the PMN substances is resumed. However, cessation of manufacturing,
processing and use of the PMN substances for less than the 6 month period does not constitute
grounds for postponement of the 6 month deadline to conduct exposure monitoring.
(ii) If any representative samples taken during the initial exposure monitoring
reveal an airborne concentration above the TWA, the Company shall repeat the exposure
monitoring for that exposure group at least every 3 months. If the PMN substances are not
manufactured, processed, or used at all during a given 3 month calendar period, the Company is
not required to conduct exposure monitoring until manufacture, processing, or use of the PMN
substances is resumed. However, cessation of manufacturing, processing and use -of the PMN,
substances for less than the 3 month period does not constitute .grounds for p©s"nement of the>•
DEQ-CFW 00003392

27
3 month deadline to conduct exposure monitoring.
(iii) The Company may alter the exposure monitoring schedule from every 3
months to every 6 months for any exposure group for whom two consecutive measurements
taken at least 7 days apart indicate that the potential exposure has decreased to the TWA or
below, but is at or above the action level. Where the PMN substances are manufactured,
processed, or used in batches of duration less than 7 days, the 2 consecutive measurements may
be taken at least 24 hours apart, provided that the measurements accurately reflect the highest
peak exposures and variability in exposure.
(4) Termination of Monitoring.
(i) If representative samples taken during the initial exposure monitoring reveal
an airborne concentration below the action level, the Company may discontinue monitoring for
that exposure group, except when additional exposure monitoring is required by paragraph (d)(5)
of this New Chemical Exposure Limit section.
(ii) If representative samples taken during the periodic monitoring reveal that an
airborne concentration, as indicated by at least 2 consecutive measurements taken at least 7 days
apart, are below the action level, the Company may discontinue the monitoring for that exposure
group, except when additional monitoring is required by paragraph (d)(5) of this New Chemical
Exposure Limit section. Where the PMN substances are manufactured, processed, or used in
batches of duration less than 7 days, the 2 consecutive measurements maybe taken at least 24
hours apart, provided that the measurements accurately reflect the highest peak exposures and
variability in exposure.
(5) Additional Monitorini4.
DEQ-CFW 00003393

M.
(i) For a previously monitored exposure group, the Company shall, within 7 days
of any of the events listed below in this paragraph (d)(5)(i), conduct the initial exposure
monitoring followed by any periodic or additional exposure monitoring required by subsection
(d) of this New Chemical Exposure Limit section:
(1) change in the production volume, process, control equipment,
personnel or work practices that may reasonably cause new or additional exposures to the PMN
substances;
(11) spills, leaks, ruptures or other breakdowns occur that may reasonably
cause new or additional exposures to the PMN substances; and
(III) whenever else the Company has any reason to suspect a change that
may reasonably result in new or additional exposures to the PMN substances.
(ii) In no event is the additional exposure monitoring requirement in paragraph
(d)(5)(i) intended to delay implementation of any necessary cleanup or other remedial action.
During any cleanup or remedial operations that may occur before commencing additional
exposure monitoring, the Company shall ensure that potentially exposed persons use at least the
respiratory protection specified in subsection (e) for the measured airborne concentration, or
more protective respiratory equipment deemed appropriate by the best professional judgment of a
qualified expert.
(6) Notification of Monitoring Results.
(i) Within 15 working days after receipt of the results of any exposure monitoring
required by this Order, the Company shall notify each person whose exposure is represented by
that monitoring. The notice shall identify the NOEL, the exposure monitoring results, and any
DEQ-CFW 00003394

29
corresponding respiratory protection required by subsection (e). Affected persons shall be
notified in writing either individually or by posting the information in an appropriate and
accessible location.
(ii) Whenever the NCEL is exceeded, the written notification required by the
preceding paragraph shall describe the action being taken by the Company to reduce inhalation
exposure to or below the NOEL, or shall refer to a document available to the person which states
the actions to be taken to reduce exposure.
(7) Exemption based on Objective Data. Where the Company has documented and
reliable objective data demonstrating that, even under worst -case conditions, employee exposure
to the PMN substances will not exceed the action level (defined in paragraph (d)(1)(i)) under the
expected handling procedures and conditions for a specific "exposure group" (defined in
paragraph (d)(1)(ii)), then that exposure group is exempt from this New Chemical Exposure
Limit section (except paragraph (d)(5) "Additional Monitoring" and subsection (f) "NCEL
Record -keeping") and the respirator requirements in the Protection in the Workplace section of
this Order. Any such objective data must accurately characterize actual employee exposures to
the PMN substances and must be obtained under conditions closely resembling the types of
materials, processes, control methods, work practices, and environmental conditions in the
Company's current workplace operations with the PMN substances. Examples of objective data
that may be used to demonstrate that employee exposure will not exceed the action level, even
under worst case conditions, include information on the physical and chemical properties of the
PMN substances, industry -wide studies, and/or laboratory test results.
DEQ-CFW 00003395

M
(e) Respiiratojy Protection.
(1) General. Whenever the Company has conducted exposure monitoring at a workplace
in accordance with subsection (d) of this New Chemical Exposure Limit section and the
measured airborne concentration of the PMN substances for any person who is reasonably likely
to be exposed to the PMN substances by inhalation exceeds the NCEL, the Company shall
provide those persons the respirators specified in this subsection (e) (rather than the respirator(s)
identified in the Protection in the Workplace section of this Order), and shall ensure that the
respirators are used (including training, fit testing, and maintenance) in accordance with OSHA
and NIOSH respiratory protection requirements at 29 CPR 1910.134 and 42 CPR Part 84. When
the Company has not yet measured the airborne concentration of the PMN substances at a
workplace in accordance with this New Chemical Exposure Limit section, the Company shall
comply with the respirator requirements in the Protection in the Workplace section of this Order
at that workplace.
(2) Selection of Appropriate Respiratory Protection. After the Company has conducted
exposure monitoring in accordance with subsection (d) of this New Chemical Exposure Limit
section, the Company shall select, provide, and ensure that persons who are reasonably likely to
be exposed to the PMN substances by inhalation use, at a minimum, the respiratory protection
which corresponds in the following table to the measured airborne concentration (or a more
protective respirator which corresponds to a concentration higher than measured)
Measured Required Respiratory Protection
Concentration
of PMN Substance
DEQ-CFW 00003396

31
< NCEL -- No respiratory protection is required.
< 10 x NCEL LED on Cartridge Service Life Testing has been Reviewed and
Approved by EPA:
— NIOSH-certified air -purifying, tight -fitting full -face respirator equipped
with the appropriate gas/vapor cartridges (organic vapor, acid gas, or
substance -specific).
-- NIOSH-certified powered air -purifying respirator equipped with a loose
fitting hood or helmet and equipped with the appropriate gas/vapor
cartridges (organic vapor, acid gas, or substance -specific).
< 25 x NCEL Data on Cartridge Service Life Testing has been Reviewed and
Approved by EPA:
-- NIOSH certified air -purifying, tight -fitting full -face respirator equipped
with the appropriate gas/vapor cartridges (organic vapor, acid gas, or
substance -specific).
-- NIOSH-certified powered air -purifying respirator equipped with a loose -
fitting hood or helmet and the appropriate gas/vapor cartridges (organic
vapor, acid gas, or substance -specific).
< 50 x NCEL Data on Cartridge Service Li e Testing has been Reviewed and
Approved by EPA:
-- NIOSH-certified air -purifying, tight -fitting full -face respirator equipped
with the appropriate gas/vapor cartridges (organic vapor, acid gas, or
substance -specific).
&No Cartridge Service Life Testing Available:
" NIOSH-certified supplied -air respirator operated in pressure demand or
continuous flow mode and equipped with a tight -fitting full. facepiece.
< 2000 x NCEL -- NIOSH-certified supplied -air respirator operated in pressure demand or
DEQ-CFW 00003397

32
other positive pressure mode and equipped with a tight -fitting full
facepiece.
> 2000 x NCEL -- Any self-contained respirator equipped with a full facepiece and
operated in apressure demand or other positive pressure mode.
-- Any supplied -air respirator equipped with a full facepiece operated in a
pressure demand or other positive pressure mode in combination with an
auxiliary self-contained breathing apparatus operated in a pressure demand
or other positive pressure mode.
(3) Reductions in Respiratory Protection. After appropriate respiratory protection has
been selected based on the results of actual exposure monitoring conducted at a workplace in
accordance with subsection (d) of this New Chemical Exposure Limit section, the Company shall
not, at that workplace, use the respiratory protection required by the Protection in the Workplace
section of this Order (unless it is the same as required by this New Chemical Exposure Limit
section). Before the Company may make any reduction in any respiratory protection selected
pursuant to this New Chemical Exposure Limit section, the Company must verify, by 2
consecutive measurements taken at least 7 days apart, that the new respiratory protection is
appropriate in accordance with paragraph (e)(2). Where the PMN substances is manufactured,
processed, or used in batches of duration less than 7 days, the 2 consecutive measurements may
be taken at least 24 hours apart, provided that the measurements accurately reflect the highest
peak exposures and variability in exposure.
(4) Special Situations.
(i) Measurements Outside Quantitation Limits. When a value less than the lower
quantitation limit ("LQL") of the analytical method (as described in paragraph (c)(4)(ii)) is
DEQ-CFW 00003398

33
measured, the Company shall estimate potential exposure using generally established and
accepted statistical methods. If the Company obtains an exposure monitoring sample that is
more than 10% above the actual upper quantitation limit C UQU') of the analytical method, the
Company must ensure that its workers wear at least a NIOSH-certified supplied -air respirator
operated in pressure demand or other positive pressure mode and equipped with a tight -fitting
full facepiece. Any reductions in this respiratory protection must comply with paragraph (e)(3).
The, _Cgmpapymay submit an improved analytical method provided that it complies fully with
subsection (c) of this New Chemical Exposure Limit section, including the verification required
by subsection (c)(3).
(ii) Cleanup and Remedial Actions. During any special cleanup or other remedial
actions that may occur before commencing additional exposure monitoring (as discussed in
paragraph (d)(5)(ii)), the Company shall ensure that potentially exposed persons use at least the
respiratory protection specified above in this subsection (e) for the measured airborne
concentration, or more protective respiratory equipment deemed appropriate by the best
professional judgment of a qualified expert.
(f) NCEL RecordkeMing.
(1) Whenever the Company elects to comply with this New Chemical Exposure Limit
section rather than the respirator requirements in the Protection in the Workplace section of this
Order, the Company shall maintain the following records until 30 years aver the date they are
created, and shall make them available for inspection and copying by EPA in accordance with
section 11 of TSCA:
(i) A copy of the sampling and analytical methods used and continuing evidence
DEQ-CFW 00003399

34
of their accuracy over time as required by section (c);
(ii) Records documenting compliance with the analytical method verification
requirements of subsection (c)(3), including copies of the signed certification statement and the
verification results obtained by both laboratories;
(iii) Records documenting either compliance with the Good Laboratory Practice
Standards at 40 CFR Part 792, or use of a laboratory accredited by the American Industrial
Hygiene Association ("AIHA") or another comparable program approved inadvance in writing., -
by EPA. Where the Company elects to not comply with TSCA GLPS, such records shall include
the written accreditation from the AlHA or the written approval from EPA.
(iv) Records documenting all exposure monitoring dates, duration, and results of
each sample taken;
(v) Records documenting the name, address, work shift, job classification, and
work area of the person monitored and of all other persons whose exposures the monitoring is
intended to represent;
(vi) Any conditions that might have affected the monitoring results;
(vii) Notification of exposure monitoring results required by paragraph (d)(6);
(viii) Records documenting any changes in the production, process, control
equipment, personnel or work practices that may reasonably cause new or additional exposures to
the PMN substances;
(ix) Records documenting any spills, leaks, ruptures or other breakdowns that
may cause new or additional exposure;
any;
(x) The type of respiratory protective devices worn by the monitored person, if
DEQ-CFW 00003400

substances;
35
(xi) Records documenting any actions taken to mitigate exposures to the PMN
(xii) Records documenting reliance on the objective data exemption in paragraph
(d)(7), including: (A) the source of the data, (B) protocols and results of any relevant testing or
analysis, (C) a description of the operation exempted and how the -data demonstrate that
employee exposures will not exceed the action level, (D) other data relevant to the operations,
materials and employee exposures covered by the exemption.
MANUFAC A ING
(a) (1) Prohibition. The Company shall not cause, encourage, or suggest the manufacture or
import of the PMN substances by any other person.
(2) Sunset Following SNUR. Subparagraph (a)(1) shall expire 75 days after
final significant new use rule ("SNUB") governing the PMN substances under
promulgation of a
section 5(a)(2) of TSCA unless the Company is notified on or.before that day of an action in a
Federal Court seeking judicial review of the SNUR. If the Company is so notified, subparagraph
(a)(1) shall not expire until EPA notifies the Company in writing that all Federal Court actions
involving the SNUR have been resolved and the validity of the SNUR affirmed.
(3) Notice of SNUR. When EPA promulgates a final SNUR for the PMN substances and
subparagraph (a)(1) expires in accordance with subparagraph (a)(2), the Company shall notify
each person whom it causes, encourages or suggests to manufacture or import the PMN
substances of the existence of the SNUR.
DEQ-CFW 00003401

36
CONTROL OF EFFLUENT & EMISSIONS
(a) The Company shall recover and capture (destroy) or recycle the PMN substances at an
overall efficiency of 99% from all the effluent process streams and the air emissions (point
source and fugitive).
DISTRIBUTION
(a) Distribution Requirements. Except as provided in paragraph (b), the Company shall
distribute the PMN substances outside the Company, only to a person who has agreed in writing
prior to the date of distribution, to:
(1) Comply with the same requirements and restrictions, if any, required of the Company
in the Protection in the Workplace and the New Chemical Exposure Limit sections of this Order;
(2) Distribute the PMN substances only to a person who will either recover and capture
(destroy) or recycle the PMN substances from all effluent process streams and air emissions
(point source and fugitive) at an overall efficiency of 99%; and
(3) Distribute the PMN substance P-08-509 in an aqueous dispersion of the polymer
product or on a heat treated solid product such that the contents polymer residual P-08-508/509
cumulative total [ ] are below 200 ppb level using the ASE method developed by
Larsen et al' with the level of quantification (LOQ) for the standard solution at 0.5 ppb. If non -
heat treated solid polymer is distributed by the Company, such person shall not further distribute
until heat treatment is performed at temperature and residence time sufficient to produce a
product with P08-508/509 cumulative residual levels equivalent to the heat treated
'Larsen et. al, "Efficient "total" extraction of
perfluorooctanoate from polytetrafluoroethylene fluoropolymer",
.Analyst:, 2006, 131, 1105-1108.
DEQ-CFW 00003402

37
polymer distributed by the Company, (i.e., below 200 ppb).
(b) Temporary Transport and Storm Notwithstanding paragraph (a), the Company may
distribute the PMN substances outside the Company for temporary transport and storage in sealed
containers provided the following two conditions are met:
(1) Subsequent to any such exempt temporary transport or storage of sealed containers, the
PMN substances may be distributed only to the Company or a person who has given the Company
the written agreement required by paragraph (a).
(2) Any human exposure or environmental release resulting from opening the sealed
containers and removing or washing out the PMN substances may occur only while the PMN
substances is in the possession and control of the Company or a person who has given the
Company the written agreement required by paragraph (a).
(c) Recipient Nan -Compliance. lf, at any time after commencing distribution in commerce of the
PMN substances, the Company obtains knowledge that a recipient of the substance has failed to
comply with any of the conditions specified in paragraph (a) of this Distribution section or, after
paragraph (a)(1) expires in accordance with subparagraph (d)(1), has engaged in a significant new
use of the PMN substances (as defined in 40 CFR Part 721, Subpart E) without submitting a
significant new use notice to EPA, the Company shall cease supplying the substance to that
recipient, unless the Company is able to document each of the following:
(1) That the Company has, within 5 working days, notified the recipient in writing that the
recipient has failed to comply with any of the conditions specified in paragraph (a) of this
Distribution section, or has engaged in a significant new use of the PMN substances without
DEQ-CFW 00003403

38
submitting a significant new use notice to EPA.
(2) That, within 15 working days of notifying the recipient of the noncompliance, the
Company received from the recipient, in writing, a statement of assurance that the recipient is
aware of the terms of paragraph (a) of this Distribution section and will comply with those terms,
or is aware of the terms of the significant new use rule for the PMN substances and will not engage
in a significant new use without submitting a significant new use notice to EPA.
(3) If, after receiving a statement of assurance from a recipient under subparagraph (c)(2)
of this Distribution section, the Company obtains knowledge that the recipient has failed to comply
with any of the conditions specified in paragraph (a) of this Distribution section, or has engaged -in
a significant new use of the PMN substances without submitting a significant new use notice to
EPA, the Company shall cease supplying. the PMN substances to that recipient, shall notify EPA of
the failure to comply, and shall resume supplying the PMN substances to that recipient only upon
written notification from the Agency.
(d) Sunset Following SNLJR. (1) Paragraph (a)(1) of this Distribution section shall expire 75 days
after promulgation of a final SNUR for the PMN substances under section 5(a)(2) of TSCA, unless
the Company is notified on or before that day of an action in a Federal Court seeking judicial
review of the SNUB. If the Company is so notified, paragraph (a)(1) of this Distribution section
shall not expire until EPA notifies the Company in writing that all Federal Court actions involving
the SNUR have been resolved and the validity of the SNUB. affirmed.
(2) When EPA promulgates a final SNUR for the PMN substances and paragraph (a)(1) of
this Distribution section expires in accordance with subparagraph (d)(1), the Company shall notify
each person to wham it distributes the PMN substances of the existence of the SNUB Such
DEQ-CFW 00003404

39
notification must be in writing and must specifically include all limitations contained in the SNUR
which are defined as significant new uses, and which would invoke significant new use notification
to EPA for the PMN substances. Such notice must also reference the publication of the SNUR for
this PMN substances in either the Federal Rexster or the Code of Federal Regulations. After
promulgation of a SNUR and expiration of subparagraph (a)(1); such notice may substitute for the
written agreement required in the introductory clause of paragraph (a); so that, if the Company
provides such notice to the persons to whom it distributes the PMN substances, then the Company
is not irequired to obtain from such persons the written agreement specified in paragraph (a).
III. RFCORDKEEPJING
(a) Records. The Company shall maintain the following records until 5 years after the date they
are created and shall make them available for inspection and copying by EPA in accordance with
section 11 of TSCA:
(1) Exemptions. Records documenting that the PMN substances did in fact qualify for any
one or more of the exemptions described in Section I, Paragraph (b) of this Order. Such records
must satisfy all the statutory and regulatory recordkeeping requirements applicable to the
exemption being claimed by the Company. Any amounts or batches of the PMN substances
eligible for the Export exemption in Section I, Paragraph (b)(3) of this Order, are exempt from all
the requirements in this Recordkeeping section, if the Company maintains, for 5 years from the
date of their creation, copies of the export label and export notice to EPA, required by TSCA
sections 12(a)(1)(B) and 12(b), respectively. Any amounts or batches of the PMN substances
eligible for the Research and Development exemption in Section I, Paragraph (b)(2) of this Order,
are exempt from all the requirements in this Recordkeeping section, if the Company maintains, for
DEQ-CFW 00003405

40
5 years from the date of their creation, the records required by 40 CFR 720.78(b). For any amounts
or batches of the PMN substances claimed to be eligible for any other exemption described in
section -I, Paragraph (b) of- 's:0fderj the Company shall keep records demonstrating qualification
for that exemption as well as the records specified in paragraphs (2) and (3) below, but is exempt
from the other recordkeeping requirements in this Recordkeeping section;
(2) Records documenting the manufacture and importation volume of the PMN substances
and the corresponding dates of manufacture and import;
(3) Records documenting the names and addresses (including shipment destination
address, if different) of all persons outside the site of manufacture or importto whom the Company
directly sells or transfers the PMN substances, the date of each sale or transfer, and the quantity of
the substance sold or transferred on such date;
use;
(4) Records documenting the address of all sites of manufacture, import, processing, and
(5) Records documenting establishment and implementation of a program for the use of
any applicable personal protective equipment required pursuant to the Protection in the Workplace
section of this Order;
(6) Records documenting the determinations required by the Protection in the Workplace
section of this Order that chemical protective clothing is impervious to the PMN substances;
(7) Records required by paragraph (f). of the New Chemical Exposure Limits section of
this Order, if applicable;
(8) Records documenting compliance with any applicable manufacturing, processing, use,
and distribution restrictions in the Manufacturing and Distribution sections of this Order, including
distributees' written agreement to comply with the Distribution section of this Order;
DEQ-CFW 00003406

41
(9) Records documenting compliance with the Control of Effluent & Emissions section of
this Order;
(10) Copies of any Transfer Documents and notices required by the Successor Liability
section of this Order, if applicable; and
(11) The Company shall keep a copy of this Order at each of its sites where the PMN
substances are manufactured or imported.
(b) Applic_ ability. The provisions of this Recordkeeping Section are applicable only to activities of
the Company and its Contract Manufacturer, if applicable, and not to activities of the Company's
customers.
(c) OMB Control Number. Under the Paperwork Reduction Act and its regulations at 5 CFR Part
1320, particularly 5 CFR 1320.5(b), the Company is not required to respond to this "collection of
information" unless this Order displays a currently valid control number from the Office of
Management and Budget (OMB), and EPA so informs the Company. The "collection of
information" required in this TSCA §5(e) Consent Orders has been approved under currently valid
OMB Control Number 2070-0012.
IV REQUESTS FOR PRE -INSPECTION INFORMATION
(a) EPA's Request for Information. Pursuant to section 11 of TSCA and 40 CFR 720.122, EPA
may ocassionally conduct on -site compliance inspections of Company facilities and conveyances
associated with the PMN substances. To facilitate such inspections, EPA personnel may contact
the Company in advance to request information pertinent to the scheduling and conduct of such
DEQ-CFW 00003407

42
inspections. Such requests may be written or oral. The types of information that EPA may request
may include, but are not limited to, the following:
(i) Expected dates and times when the PMN substances will be in production within the
subsequent 12 months;
(ii) Current workshift schedules for workers who are involved in activities associated with
the PMN substances and may reasonably be exposed to the PMN substances;
(iii) Current job titles or categories for workers who are involved in activities associated
with the PMN substances and may reasonably be exposed to the PMN substances;
(iv) Existing exposure monitoring data for workers who are involved in activities
associated with the PMN substances and may reasonably be exposed to the PNIN substances;
(v) Records required by the Recordkeeping section of this Order; and/or
(vi) Any other information reasonably related to determining compliance with this Order or
conducting an inspection for that purpose.
(b) CpMppy s Response. The Company shall respond to such requests within a reasonable period
of time, but in no event later than 30 days after receiving EPA's request. When requested in
writing by EPA, the Company's response shall be in writing. To the extent the information is
known to or reasonably ascertainable to the Company at the time of the request, the Company's
response shall demonstrate a good faith effort to provide reasonably accurate and detailed answers
to all of EPA's requests..
(c) Confidential Business Information. Any Confidential Business Information ("CBI ,) that the
Company submits to EPA pursuant to paragraph (b) shall be protected in accordance with § 14 of
DEQ-CFW 00003408

43
TSCA and 40 CFR Part 2.
V. SUCCESSOR LIABILITY UPON TRANSFER OF CONSENT ORDER
(a) Scope. This section sets forth the procedures by which the Company's rights and obligations
under this Order maybe transferred when the Company transfers its interests in the PMN
substances, including the right to manufacture the PMN substances, to another person outside the
Company (the "Successor in Interest").
(b) Relation of Transfer Date to Notice of Commencement ("NOC").
(1) Before NOC. If the transfer from the Company to the Successor in Interest is effective
before EPA receives a notice of commencement of manufacture or import ("NOC") for the PMN
substances from the Company pursuant to 40 CFR 720.102, the Successor in Interest must submit a
new PMN to EPA and comply fully with Section 5(a)(1) of TSCA and 40 CFR part 720 before
commencing manufacture or import of the PMN substances.
(2) After NOC. If the transfer from the Company to the Successor in Interest is effective
after EPA receives a NOC, the Successor in Interest shall comply with the terms of this Order and
shall not be required to submit a new PMN to EPA.
(c) Definitions. The following definitions apply to this Successor Liability section of the Order:
(1) "Successor in Interest" means a person outside the Company who has acquired the
Company's fall interest in the rights to manufacture the PMN substances, including all ownership
rights and legal liabilities, through a transfer document signed by the Company, as transferor, and
the Successor in Interest, as transferee. The term excludes persons who acquire less than the full
DEQ-CFW 00003409

interest of the Company in the PMN substances, such as a licensee who has acquired a limited
license to the patent or manufacturing rights associated with the PMN substances. A, Successor in
Interest must be incorporated, licensed, or doing business in the United States in accordance with
40 CFR 720.22(a)(3).
(2) "Transfer Document" means the legal instrument(s) used to convey the interests in the
PMN substances, including the right to manufacture the PMN substances, from the Company to the
Successor in Interest.
(d) Notices.
(1) Notice to Successor in Interest. On or before the effective date of the transfer, the
Company shall provide to the Successor in Interest, by registered mail, a copy of the Consent Order
and the "Notice of Transfer" document which is incorporated by reference as Attachment C to this
Order.
(2) Notice to EPA. Within 10 business days of the effective date of the transfer, the
Company shall, by registered mail, submit the fully executed Notice of Transfer document to: U.S.
Environmental Protection Agency, New Chemicals Branch (7405), 1200 Pennsylvania Avenue,
N.W., Washington, D.C. 20460.
(3) Transfer Document. Copies of the Transfer Document must be maintained by the
Successor in Interest at its principal place of business, and at all sites where the PMN substances is
manufactured or imported. Copies of the Transfer Document must also be made available for
inspection pursuant to Section 11 of TSCA, must state the effective date of transfer, and must
contain provisions which expressly transfer liability for the PMN substances under the terms of this
Order from the Company to the Successor in Interest.
DEQ-CFW 00003410

45
(e) Liability-.
(1) The Company shall be liable for compliance with the requirements of this Order until
the effective date of the transfer described above.
(2) The Successor in Interest shall be liable for compliance with the requirements of this
Order effective as of the date of transfer.
(3) Nothing in this section shall be construed to prohibit the Agency from taking
enforcement action against the Company after the effective date of the transfer for actions taken, or
omissions made, during the time in which the Company manufactured, processed, used, distributed
in commerce, or disposed of the PMN substances pursuant to the terms of this Consent Order.
W Obli ations to Submit Test Data under Consent Order. If paragraph (d) of the Testing section
of this Consent Order requires the Company to submit test data to EPA at a specified production
volume ("test trigger"), the aggregate volume of the PMN substances manufactured and imported
by the Company up to the date of transfer shall count towards the test trigger applicable to the
Successor in Interest.
VI. MODIFICATION AND REVOCATION OF CONSENT ORDER
The Company may petition EPA at any time, based upon new information on the health
effects of, or human exposure to, the PMN substances, to modify or revoke substantive provisions
of this Order. The exposures and risks identified by EPA during its review of the PMN substances
and the information EPA determined to be necessary to evaluate those exposures and risks are
described in the preamble to this Order. However, in determining whether to amend or revoke this
Order, EPA will consider all relevant information available at the time the Agency makes that
DEQ-CFW 00003411

46
determination, including, where appropriate, any reassessment of the test data or other information
that supports the findings in this Order, an examination of new test data or other information or
analysis, and any other relevant information.
EPA will issue a modification or revocation if EPA determines that the activities proposed
therein will not present an unreasonable risk of injury to health or the environment and will not
result in significant or substantial human exposure or substantial environmental release in the
absence of data sufficient to permit a reasoned evaluation of the health or environmental effects of
the PMN substances.
In addition, the Company may petition EPA at any time to. make other modifications to the
language of this Order. EPA will issue such a modification if EPA determines that the
modification is useful, appropriate, and consistent with the structure and intent of this Order as
issued.
DEQ-CFW 00003412

47
V L EFFECT OF CONSENT ORDER
By consenting to the entry of this Order, the Company waives its rights to file objections to
this Order pursuant to section 5(e)(1)(C) of TSCA, to receive service of this Order no later than 45
days before the end of the review period pursuant to section 5(e)(1)(B) of TSCA, and to challenge
the validity of this Order in any subsequent action. Consenting to the entry of this Order, and
agreeing to be bound by its terms, do not constitute an admission by the Company as to, the facts
or conclusions underlying the Agency's determinations in this proceeding. This waiver does not
affect any other rights that the Company may have under TSCA.
1/26/09
Date
1/28/09
Date
Jim Willis, Director
Chemical Control Division
Office of Pollution Prevention and Toxics
Name: James R. Hoover
Title: Global Regulatory Manager
Company: DuPont Company
DEQ-CFW 00003413

ATTACH—WNT A
DEFINITIONS
[Note: The attached Order may not contain some of the terms defined below.]
"Chemical name" means the scientific designation of a chemical substance in accordance
with the nomenclature system developed by the International Union of Pure and Applied
Chemistry or the Chemical Abstracts Service's rules of nomenclature, or a name which will clearly
identify a chemical substance for the purpose of conducting a hazard evaluation._
"Chemical protective clothing" means items of clothing that provide a protective barrier to
prevent dermal contact with chemical substances of concern. Examples can include, but are not
limited to: full body protective clothing, boots, coveralls, gloves, jackets, and pants.
"Company" means the person or persons subject to this Order.
"Commercial use" means the use of a chemical substance or any mixture containing the
chemical substance in a commercial enterprise providing saleable goods or a service to consumers
(e.g., a commercial dry cleaning establishment or painting contractor).
"Common name" means any designation or identification such as code name, code number,
trade name, brand name, or generic chemical name used to identify a chemical substance other than
by its chemical name.
"Consumer" means a private individual who uses a chemical substance or any product
containing the chemical substance in or around a permanent or temporary household or residence,
during recreation, or for any personal use or enjoyment.
"Consumer product" means a chemical substance that is directly, or as part of a mixture,
sold or made available to consumers for their use in or around a permanent or temporary household
or residence, in or around a school, or in recreation.
"Container" means any bag, barrel, bottle, box, can, cylinder, drum, reaction vessel, storage
tank, or the like that contains a hazardous chemical. For purposes of this section, pipes or piping
systems, and engines, fuel tanks, or other operating systems in a vehicle, are not considered to be
containers.
"Contract Manufacturer" means a person, outside the Company, who is authorized to
manufacture and import the PMN substance under the conditions specified in Part H. of this
Consent Order and in the Consent Order for Contract Manufacturer.
"Identity" means any chemical or common name used to identify a chemical substance or a
mixture containing that substance.
DEQ-CFW 00003414

2
"Immediate use." A chemical substance is for the "immediate, use" of a person if it is under
the control of, and used only by, the person who transferred it from a labeled container and will
only be used by that person within the work shift in which it is transferred from the labelled
container.
"Impervious." Chemical protective clothing is "impervious" to a chemical substance if the
substance causes no chemical or mechanical degradation, permeation, or penetration of the
chemical protective clothing under the conditions of, and the duration of, exposure.
"Manufacturing stream" means all reasonably anticipated transfer, flow, or disposal of a
chemical substance, regardless of physical state or concentration, through all intended operations
of manufacture, including the cleaning of equipment.
II MSDS" means material safety data sheet, the written listing of data for the chemical
substance.
"NIOSH" means the National Institute for Occupational Safety and Health of the U.S.
Department of Health and Human Services.
"Non -enclosed process" means any equipment system (such as an open -top reactor, storage
tank, or mixing vessel) in which a chemical substance is manufactured, processed, or otherwise .
used where significant direct contact of the bulk chemical substance and the workplace air may
occur.
"Non -industrial use" means use other than at a facility where chemical substances or
mixtures are manufactured, imported, or processed.
"PMN substance" means the chemical substance described in the Promanufacture notice
submitted by the Company relevant to this Order.
"Personal protective equipment" means any chemical protective clothing or device placed
on the body to prevent contact with, and exposure to, an identified chemical substance or
substances in the work area. Examples include, but are not limited to, chemical protective
clothing, aprons, hoods, chemical goggles, face splash shields, or equivalent eye protection, and
various types of respirators. Barrier creams are not included in this definition.
"Process stream" means all reasonably anticipated transfer, flow, or disposal of a chemical
substance, regardless of physical state or concentration, through all intended operations of
processing, including the cleaning of equipment.
"Scientifically invalid" means any significant departure from the EPA -approved protocol or
the Good Laboratory Practice Standards at 40 CFR Part 792 without prior or subsequent Agency
approval that prevents a reasoned evaluation of the health or environmental effects of the PMN
substance.
DEQ-CFW 00003415

3
"Scientifically equivocal data" means data which, although developed in apparent
conformity with the Good Laboratory Practice Standards and EPA -approved protocols, are
inconclusive, internally inconsistent, or otherwise insufficient to permit a reasoned evaluation of
the potential risk of injury to human health or the environment of the PMN substance.
"Sealed container" means a closed container that is physically and chemically suitable for
long-term containment of the PMN substance, and from which there will be no human exposure to,
nor environmental release of, the PMN substance during transport and storage.
"Use stream" means all reasonably anticipated transfer, flow, or disposal of a chemical
substance, regardless of physical state or concentration, through all intended operations of
industrial, commercial, or consumer use.
"Waters of the -United States" has the meaning set forth in 40 CFR 122.2.
"Work area" means a room or defined space in a workplace where the PMN substance is
manufactured, processed, or used and where employees are present.
"Workplace" means an establishment at one geographic location containing one or more
work areas.
DEQ-CFW 00003416

ATTACHMENT B
STATISTICAL ANALYSIS OF NCELs ANALYTICAL METHOD
VERIFICATION RESULTS
This Attachment describes the statistical technique (with examples) for comparing the
analytical results obtained by two laboratories pursuant to paragraph (c)(3)(vii) of the New
Chemical Exposure Limit section of this Order.
STATISTICAL TECHNIQUE
where,
To obtain two -sample t test with unequal variances, perform the following operations:
• Compute means of the data measured by two laboratories.
• Compute mean squares
S�2 = �(X j - X.)z/(n; - 1), i=l, 2
• Form the ratio
T = (Xi - X2)/(Wi + W2)14'
• Compute degrees of freedom
f = (Wj + W2)2/[Wl2/(nl - 1) + W2z/(n2 - 1)]
W, =- Stz/n,, i =1, 2
X, = Average of the results from the company laboratory
X2 = Average of the results from the independent laboratory
nj = Number of samples analyzed by the company laboratory
n2 = Number of samples analyzed by the independent laboratory.
Then compare the absolute value of to the 97.5 percentile point of a t distribution with f
degrees of freedom. If the absolute value exceeds the 97.5 percentile point, the results measured
DEQ-CFW 00003417

2
b by two laboratories are significantly different. at 95% level. Otherwise, they are not significantly
different. In general, f may not be a integer. Use interpolation to obtain the 97.5 percentile point
of a t distribution with f degrees of freedom..
EXAMPLES -- The following examples (based on simulated data) illustrate the method:
Example 1
Data Set 1
80.56
100.01
86.04
52.61
84.85
95.75
Xz = 83.30 nl = 6 X2 = 100.40
Si' = 278.72 W1= 46.25 S22 = 9.26
Absolute value of T = 2.467 f = 5.33
Data Set 2
97.11
102.13
99.83
97.83
105.44
100.04
n2 = 6
W2 =1.54
The t table shows that the 97.5 percentile point is 2.571 and 2.447 for 5 and 6 degrees of
freedom, respectively. For 5.33 degrees of freedom, the 97.5 percentile point will be
approximately 2.530 which is greater than the absolute value of T, 2.467. Hence, the means of
two data sets are not significantly different at the 5% level.
However, if this problem had been treated as an ordinary two -sample t test, the means
would be significantly different at the 5% level because the absolute of T is greater than 2.228, the
97.5 percentile point for the t distribution with 10 degrees. of freedom..
Example 2
Data Set 1
82.87
101.85
87.44
99.68
101.15
99.21
X,=95.37 nF=6 X2=
104.37 n.2=6
Data Set 2
108.05
96.51
100.04
104.33
110.32
107.00
DEQ-CFW 00003418

3
S11= 65.59 W1= 10.93 S 2 2 = 27.25 W2 = 4.54
Absolute value of T = 2.290 f = 8.54
The t table shows that for 8 and 9 degrees of freedom the 97.5 percentile point is 2.306 and
2.262, respectively. For 8.54 degrees of freedom the 97.5 percentile point will be approximately
2.282 which is less than the absolute value of T, 2.290. Hence, the means of two data sets are
.significantly different at the 5% level.
DEQ-CFW 00003419

ATTACHMENT C
NOTICE OF TRANSFER
OF
TOXIC SUBSTANCES CONTROL ACT
SECTION 5(e) CONSENT ORDER
Company (Transferor) PMN Number
1. Transfer of Manufacture Rights. Effective on , the Company did sell or
otherwise transfer to , ("Successor in Interest") the rights
and liabilities associated with manufacture of the above -referenced chemical substance, which was
the subject of a premanufacture notice ("PMN") and is governed by a Consent Order issued by the
U.S. Environmental Protection Agency ("EPA") under the authority of §5(e) of the Toxic
Substances Control Act (TSCA, 15 U.S.C. §2604(e)).
2. Assumption of Liability. The Successor in Interest hereby certifies that, as of the effective date
of transfer, all actions or omissions governed by the applicable Consent Order limiting
manufacture, processing, use, distribution in commerce and disposal of the PMN substance, shall
be the responsibility of the Successor in. Interest. Successor in Interest also certifies that it is
incorporated, licensed, or doing business in the United States in accordance with 40 CFR
720.22(a)(3).
3. Confidential Business Information. The Successor in Interest hereby:
_ reasserts,
relinquishes, or
modifies
all Confidential Business Information ("CBI") claims made by the Company, pursuant to Section
14 of TSCA and 40 CFR part 2, for the PMN substanee(s). Where "reasserts" or "relinquishes" is
indicated, that designation shall be deemed to apply to all such claims. Where "modifies" is
indicated, such modification shall be explained in detail in an attachment to this Notice of
Transfer. Information which has been previously disclosed to the public (e.g., a chemical identity
that was not claimed as CBI by the original submitter) would not subsequently be eligible for
confidential treatment under this Notice of Transfer.
DEQ-CFW 00003420

Company (Transferor)
TOXIC SUBSTANCES CONTROL ACT
SECTION 5(e) CONSENT ORDER
NOTICE OF TRANSFER
(continued)
PMN Number
Signature of Authorized Official Date
Printed Name of Authorized Official
Title of Authorized Official
Successor in Interest
Signature of Authorized Official Date
"Priii'ted Name o£Authorized Official
Title of Authorized Official
Address
City, State, Zip Code
DEQ-CFW 00003421

3
TOXIC SUBSTANCES CONTROL ACT
SECTION 5(e) CONSENT ORDER
NOTICE OF TRANSFER
(continued)
Successor's Technical Contact
Address
City, State, Zip Code
Phone
DEQ-CFW 00003422