WQ0031246_More Information (Received)_20230331

PF-Series Submersible Effluent Pumps:
1-Phase, 60-Hz, 4-inch (100-mm)
Applications
Our PF-Series 4-inch (100-mm) Submersible Effluent Pumps are
designed to transport screened effluent (with low TSS counts) from
septic tanks or dosing tanks. These pumps are constructed of light-
weight, corrosion -resistant stainless steel and engineered plastics, and
are field -serviceable and repairable with common tools. They're also
CSA- and UL-certified to U.S. and Canadian safety standards for efflu-
ent pumps.
PF-Series pumps are used in a variety of applications, including pressur-
ized drainfields, packed -bed filters, mounds, aerobic units, effluent irri-
gation, liquid -only (effluent) sewers, wetlands, lagoons, and more. These
pumps are designed to be used with a Biotube® pump vault or after a
secondary treatment system.
Discharge connection
Franklin liquid
end
— Suction connection
Franklin
Super Stainless
motor
Powered by
s�® Franklin Electric
us v
LR80980
LR2053896
Features/Specifications
To specify this pump for your installation, require the following:
• Minimum 24-hour run -dry capability (liquid end) with no deterioration
in pump life or performance"
• 1/8-inch (3-mm) bypass orifice to ensure flow recirculation for motor
cooling and to prevent air bind
• Liquid -end repair kits available for better long-term cost of ownership
• TRI-SEALT°" floating impeller design on 10, 20, and 30 gpm (0.6,1.3,
and 1.9 Vsec) models; floating stack design on 50 and 75 gpm (3.2
and 4.7 Vsec) models
• Franklin Electric Super Stainless motor, rated for continuous use and
frequent cycling
• Type SCOW 600-V motor cable (model PF751512 uses 14 AWG,
SJOOW, 300-V cord)
"Not applicable for 5-hp (3.73 kM models
Standard Models
See specifications chart on page 2 for a list of standard pumps. For a
complete list of available pumps, call Orenco.
Product Code Diagram
PF ❑
0❑❑-❑-❑
TLK = ClickTightTm compatible
Cord length, ft (m):$
Blank = 10 (3) 20 = 20 (6)
30 = 30 (9) 50 = 50 (15)
Check valve:
Blank = no internal check valve
CV = internal check valves
Voltage, nameplate:
1 = 115` 2 = 230
Frequency:
1 = single-phase 60 Hz
Horsepower (k":
05 = Y2 hp (0.37) 07 = 3/ hp (0.56)
10 = 1 hp (0.75) 15 = 1 h hp (1.11)
20 = 2 hp (1.50) 30 = 3 hp (2.24)
50 = 5 hp (3.73)
Nominal flow, gpm (Usec):
10 = 10 (0.6) 20 = 20 (1.3)
30 = 30 (1.9) 50 = 50 (3.2)
75 = 75 (4.7)
Pump, PF Series
Y2-hp (0.37 kw) only
r Available for 10 gpm (0.6 Usec),1/2 hp (0.37 kw)
= Note: 20-ft cords are available only for pumps through 1 Y2 hp
Second Stage Recirculation
Pump: PF500712
Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com NTD-PU-PF-1
Rev. 10 © 01/21
Page 1 of 4

Specifications
E
G
d
?�
+�+
O
Cn
Q
y •�
NCM 0
:2
U
a� y
W y03
0
ce an
� y
ca
� E
� �
� �
� �
"a �
Y
c�
a
Pump Model
c
= a
z >
¢ >
o
c
_
._
=
PH 00511 s
10(0.6)
0.50 (0.37) 1
115
120
12.7
12.7
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00511 CV 9
10(0.6)
0.50 (0.37) 1
115
120
12.7
12.7
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00512 1
10(0.6)
0.50 (0.37) 1
230
240
6.3
6.3
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00712 4, 5, 9
10(0.6)
0.75 (0.56) 1
230
240
8.3
8.3
1 '/4 in. GFP
25.9 (658)
17 (432)
30 (14)
300
PH 01012 5, 8.9
10(0.6)
1.00 (0.75) 1
230
240
9.6
9.6
1 '/4 in. GFP
27.9 (709)
18 (457)
33 (15)
100
PF200511 1
20(1.3)
0.50 (0.37) 1
115
120
12.3
12.5
1 '/4 in. GFP
22.3 (566)
18 (457)
25 (11)
300
PF200512 8
20(1.3)
0.50 (0.37) 1
230
240
6.4
6.5
1 '/4 in. GFP
22.5 (572)
18 (457)
26 (12)
300
PF201012 4,5.1
20(1.3)
1.00 (0.75) 1
230
240
10.5
10.5
1 '/4 in. GFP
28.4 (721)
20 (508)
33 (15)
100
PF201512 4,5
20(1.3)
1.50 (1.11) 1
230
240
12.4
12.6
1 '/4 in. GFP
34.0 (864)
24 (610)
41 (19)
100
PF300511 9
30(1,9)
0.50 (0.37) 1
115
120
11.8
11.8
1 '/4 in. GFP
21.3 (541)
20 (508)
28 (13)
300
PF300512 1
30(1.9)
0.50 (0.37) 1
230
240
6.2
6.2
1 '/4 in. GFP
21.3 (541)
20 (508)
25 (11)
300
PF300712 8
30(1.9)
0.75 (0.56) 1
230
240
8.5
8.5
1 '/4 in. GFP
24.8 (630)
21 (533)
29 (13)
300
PF301012 4,1
30(1.9)
1.00 (0.75) 1
230
240
10.4
10.4
1 '/4 in. GFP
27.0 (686)
22 (559)
32 (15)
100
PF301512 4,5
30(1.9)
1.50 (1.11) 1
230
240
12.6
12.6
1 '/4 in. GFP
32.8 (833)
24 (610)
40 (18)
100
PF302012 5, 6.'
30(1,9)
2.00 (1.49) 1
230
240
11.0
11.0
1 '/4 in. SS
35.5 (902)
26 (660)
44 (20)
100
PF303012 5, 6, 7, 8
30(1.9)
3.00 (2.23) 1
230
240
16.8
16.8
1 '/4 in. SS
44.5 (1130)
33 (838)
54 (24)
100
PF305012 5, 1.7, 8
30(1.9)
5.00 (3.73) 1
230
240
25.6
25.8
1 '/4 in. SS
66.5 (1689)
53 (1346)
82 (37)
100
PF500511 s
50(3.2)
0.50 (0.37) 1
115
120
12.1
12.1
2 in. SS
20.3 (516)
24 (610)
27 (12)
300
PF500512 s
50(3.2)
0.50 (0.37) 1
230
240
6.2
6.2
2 in. SS
20.3 (516)
24 (610)
27 (12)
300
PF500711k
50(3.2)
0.75 (0.56) 1
a
a
a
!.5
2 in. SS
23.7 (602)
25 (635)
31 (14)
300
PF501012 9
50(3.2)
1.00 (0.75) 1
230
240
10.1
10.1
2 in. SS
27.0 (686)
26 (660)
35 (16)
100
PF501512 4
50(3.2)
1.50 (1.11) 1
230
240
12.5
12.6
2 in. SS
32.5 (826)
30 (762)
41 (19)
100
PF503012 4,1.7, 8
50(3.2)
3.00 (2.23) 1
230
240
17.7
17.7
2 in. SS
43.0 (1092)
37 (940)
55 (25)
100
PF505012 5, 6,', 8
50(3.2)
5.00 (3.73) 1
230
240
26.2
26.4
2 in. SS
65.4 (1661)
55 (1397)
64 (29)
100
PF751012 s
75(4.7)
1.00 (0.75) 1
230
240
9.9
10.0
2 in. SS
27.0 (686)
27 (686)
34 (15)
100
PF751512
75(4.7)
1.50 (1.11) 1
230
240
12.1
12.3
2 in. SS
33.4 (848)
30 (762)
44 (20)
100
1 GFP = glass -filled polypropylene; SS = stainless steel. The 1 Y4-in. NPT GFP discharge is 2 718 in. octagonal across flats; the 1 Y4-in. NPT SS discharge is 2 118 in. octagonal across flats, -and the 2-in.
NPT SS discharge is 2 718 in. hexagonal across flats. Discharge is female NPT threaded, U.S. nominal size, to accommodate OrencO discharge hose and valve assemblies. Consult your Orenco Distributor
about fittings to connect hose and valve assemblies to metric -sized piping.
2 Minimum liquid level is for single pumps when installed in an Orenco Biotube® Pump Vault or Universal Flow Inducer. In other applications, minimum liquid level should be top of pump. Consult Orenco for
more information.
3 Weight includes carton and 10-tt (3-m) cord.
4 High-pressure discharge assembly required.
5 Do not use cam -lock option (0) on discharge assembly.
6 Custom discharge assembly required for these pumps. Contact Orenco.
7 Capacitor pack (sold separately or installed in a custom control panel) required for this pump. Contact Orenco.
8 Torque locks are available for all pumps and are supplied with 3-hp and 5-hp pumps.
9 ClickTightrm compatible.
NTD-PU-PF-1 Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com
Rev. 10 © 01 /21
Page 2 of 4

Materials of Construction
Discharge Glass -filled polypropylene or stainless steel
Discharge bearing Engineered thermoplastic (PEEK)
Diffusers Glass -filled PPO (Noryl GFN3)
Impellers Celcon® acetal copolymer on 10-, 20-, and 30-gpm models; 50-gpm impellers are Noryl GFN3
Intake screen Polypropylene
Suction connection Stainless steel
Drive shaft 7/16-in. hexagonal stainless steel, 300 series
Coupling Sintered stainless steel, 300 series
Shell Stainless steel, 300 series
Motor Franklin motor exterior constructed of stainless steel. Motor filled with deionized water and propylene glycol for constant lubrication. Hermetically
sealed motor housing ensures moisture -free windings. All thrust absorbed by Kingsbury -type thrust bearing. Rated for continuous duty. Single-
phase motors are equipped with surge arrestors for added security. Single-phase motors through 1.5 hp (1.11 k" have built-in thermal over-
load protection, which trips at 203-221° F (95-105' Q.
Using a Pump Curve
A pump curve helps you determine the best pump for your system. Pump curves show the relationship between flow and pressure (total dynamic
head or "TDH"), providing a graphical representation of a pump's optimal performance range. Pumps perform best at their nominal flow rate. These
graphs show optimal pump operation ranges with a solid line and show flow rates outside of these ranges with a dashed line. For the most accurate
pump specification, use Orenco's PumpSelecf" software.
Pump Curves
500 1 400
PF10 Series, 60 Hz, 0.5 -1.0 hp PF20 Series, 60 Hz, 0.5 1.5 h
400I _ 350 PF2015
PF1010 —
350
= e 300 --
C300
250
250 PF1007 = PF2010
� ......
'a P�1005
a -- 'a
200 cui "f ate+
200 \\ PF20051 �\
150
= 150
100 \ 100 \
50 y' . '` 50
01
0 2 4 6 8 10 12 14 16 18 0 5 10 15 20 25 30 35
Flow in gallons per minute (gpm) Flow in gallons per minute (gpm)
40
Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com NTD-PU-PF-1
Rev. 10 0 01/21
Page 3 of 4

Pump Curves, Cont.
900
800
as
700
C 600
F.
500
a�
t
400
E
300
4 200
100
0
0
100
90
80
c
70
0
60
c,s
50
40
cQ
� 30
c 20
10�
0
0
■■■L__
,
■
�MENEM
MEMEEME
MIMMMMM
M
M
�®
MMMME
MM\�
MMMMM
5 10 15 20 25 30 35 40 45
Flow in gallons per minute (gpm)
PF7515
I
[F75'O
PF75 Series, 60 Hz,1.0 -1.5 hp
I I I I I I I
I I I I I I I
I
I
I •f''••l.
I
I
I
I
I
I
I
I
I
I
I
I'•i
10 20 30 40 50 60 70 80 90 100
Flow in gallons per minute (gpm)
450
400
as
350
c
C 300
PF50;
250
m
200
= 150 PF50.
� PF50'
100
50
i I i I i
PF50 Series, 60 Hz, 0.5 - 5.0 hp
I I I I I
0
0 10 20 30 40 50 60 70 80 90
Flow in gallons per minute (gpm)
Operating Point:
24GPM @ 55 TDH
NTD-PU-PF-1 Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com
Rev. 10 © 01 /21
Page 4 of 4

PF-Series Submersible Effluent Pumps:
1-Phase, 60-Hz, 4-inch (100-mm)
Applications
Our PF-Series 4-inch (100-mm) Submersible Effluent Pumps are
designed to transport screened effluent (with low TSS counts) from
septic tanks or dosing tanks. These pumps are constructed of light-
weight, corrosion -resistant stainless steel and engineered plastics, and
are field -serviceable and repairable with common tools. They're also
CSA- and UL-certified to U.S. and Canadian safety standards for efflu-
ent pumps.
PF-Series pumps are used in a variety of applications, including pressur-
ized drainfields, packed -bed filters, mounds, aerobic units, effluent irri-
gation, liquid -only (effluent) sewers, wetlands, lagoons, and more. These
pumps are designed to be used with a Biotube® pump vault or after a
secondary treatment system.
Discharge connection
Franklin liquid
end
— Suction connection
Franklin
Super Stainless
motor
Powered by
s�® Franklin Electric
c us v
LR80980
LR2053896
Features/Specifications
To specify this pump for your installation, require the following:
• Minimum 24-hour run -dry capability (liquid end) with no deterioration
in pump life or performance"
• 1/8-inch (3-mm) bypass orifice to ensure flow recirculation for motor
cooling and to prevent air bind
• Liquid -end repair kits available for better long-term cost of ownership
• TRI-SEALT°" floating impeller design on 10, 20, and 30 gpm (0.6,1.3,
and 1.9 Vsec) models; floating stack design on 50 and 75 gpm (3.2
and 4.7 Vsec) models
• Franklin Electric Super Stainless motor, rated for continuous use and
frequent cycling
• Type SCOW 600-V motor cable (model PF751512 uses 14 AWG,
SJOOW, 300-V cord)
"Not applicable for 5-hp (3.73 kM models
Standard Models
See specifications chart on page 2 for a list of standard pumps. For a
complete list of available pumps, call Orenco.
Product Code Diagram
PF ❑
0❑❑-❑-❑
TLK = ClickTightT" compatible
Cord length, ft (m):$
Blank = 10 (3) 20 = 20 (6)
30 = 30 (9) 50 = 50 (15)
Check valve:
Blank = no internal check valve
CV = internal check valves
Voltage, nameplate:
1 = 115` 2 = 230
Frequency:
1 = single-phase 60 Hz
Horsepower (k":
05 = Y2 hp (0.37) 07 = 3/ hp (0.56)
10 = 1 hp (0.75) 15 = 1 h hp (1.11)
20 = 2 hp (1.50) 30 = 3 hp (2.24)
50 = 5 hp (3.73)
Nominal flow, gpm (Usec):
10 = 10 (0.6) 20 = 20 (1.3)
30 = 30 (1.9) 50 = 50 (3.2)
75 = 75 (4.7)
Pump, PF Series
Y2-hp (0.37 kw) only
r Available for 10 gpm (0.6 Usec),1/2 hp (0.37 kw)
= Note: 20-ft cords are available only for pumps through 1 Y2 hp
First Stage Recirculation
Pump: PF751512
Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com NTD-PU-PF-1
Rev. 10 © 01/21
Page 1 of 4

Specifications
E
G
d
?�
+�+
O
Cn
Q
y •�
NCM 0
:2
U
a� y
W
y03
0
ce an
� y
ca
� E
� �
� �
� �
"a �
Y
c�
a
Pump Model
c
=
a
z >
¢ >
o
c
_
._
=
PH 00511 s
10(0.6)
0.50 (0.37)
1
115
120
12.7
12.7
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00511 CV 9
10(0.6)
0.50 (0.37)
1
115
120
12.7
12.7
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00512 1
10(0.6)
0.50 (0.37)
1
230
240
6.3
6.3
1 '/4 in. GFP
23.0 (660)
16 (406)
26 (12)
300
PH 00712 4, 5, 9
10(0.6)
0.75 (0.56)
1
230
240
8.3
8.3
1 '/4 in. GFP
25.9 (658)
17 (432)
30 (14)
300
PH 01012 5, 8.9
10(0.6)
1.00 (0.75)
1
230
240
9.6
9.6
1 '/4 in. GFP
27.9 (709)
18 (457)
33 (15)
100
PF200511 1
20(1.3)
0.50 (0.37)
1
115
120
12.3
12.5
1 '/4 in. GFP
22.3 (566)
18 (457)
25 (11)
300
PF200512 8
20(1.3)
0.50 (0.37)
1
230
240
6.4
6.5
1 '/4 in. GFP
22.5 (572)
18 (457)
26 (12)
300
PF201012 4,5.1
20(1.3)
1.00 (0.75)
1
230
240
10.5
10.5
1 '/4 in. GFP
28.4 (721)
20 (508)
33 (15)
100
PF201512 4,5
20(1.3)
1.50 (1.11)
1
230
240
12.4
12.6
1 '/4 in. GFP
34.0 (864)
24 (610)
41 (19)
100
PF300511 9
30(1,9)
0.50 (0.37)
1
115
120
11.8
11.8
1 '/4 in. GFP
21.3 (541)
20 (508)
28 (13)
300
PF300512 1
30(1.9)
0.50 (0.37)
1
230
240
6.2
6.2
1 '/4 in. GFP
21.3 (541)
20 (508)
25 (11)
300
PF300712 8
30(1.9)
0.75 (0.56)
1
230
240
8.5
8.5
1 '/4 in. GFP
24.8 (630)
21 (533)
29 (13)
300
PF301012 4,1
30(1.9)
1.00 (0.75)
1
230
240
10.4
10.4
1 '/4 in. GFP
27.0 (686)
22 (559)
32 (15)
100
PF301512 4,5
30(1.9)
1.50 (1.11)
1
230
240
12.6
12.6
1 '/4 in. GFP
32.8 (833)
24 (610)
40 (18)
100
PF302012 5, 6.'
30(1,9)
2.00 (1.49)
1
230
240
11.0
11.0
1 '/4 in. SS
35.5 (902)
26 (660)
44 (20)
100
PF303012 5, 6, 7, 8
30(1.9)
3.00 (2.23)
1
230
240
16.8
16.8
1 '/4 in. SS
44.5 (1130)
33 (838)
54 (24)
100
PF305012 5, 1.7, 8
30(1.9)
5.00 (3.73)
1
230
240
25.6
25.8
1 '/4 in. SS
66.5 (1689)
53 (1346)
82 (37)
100
PF500511 s
50(3.2)
0.50 (0.37)
1
115
120
12.1
12.1
2 in. SS
20.3 (516)
24 (610)
27 (12)
300
PF500512 s
50(3.2)
0.50 (0.37)
1
230
240
6.2
6.2
2 in. SS
20.3 (516)
24 (610)
27 (12)
300
PF500712 9
50(3.2)
0.75 (0.56)
1
230
240
8.5
8.5
2 in. SS
23.7 (602)
25 (635)
31 (14)
300
PF501012 9
50(3.2)
1.00 (0.75)
1
230
240
10.1
10.1
2 in. SS
27.0 (686)
26 (660)
35 (16)
100
PF501512 4
50(3.2)
1.50 (1.11)
1
230
240
12.5
12.6
2 in. SS
32.5 (826)
30 (762)
41 (19)
100
PF503012 4,1.7, 8
50(3.2)
3.00 (2.23)
1
230
240
17.7
17.7
2 in. SS
43.0 (1092)
37 (940)
55 (25)
100
PF505012 5, 6,', 8
50(3.2)
5.00 (3.73)
1
230
240
26.2
26.4
2 in. SS
65.4 (1661)
55 (139�
64 (29)
100
PF751012 s
75(4.7)
1.00 (0.75)
1
230
240
9.9
10.0
2 in. SS
27.0 (686)
27 (686)
34 (15)
100
-
E4.7)
1.50 (1.11)
@
a
a
W
W
j in. SS
33.4 M
30 (762)
1 GFP = glass -filled polypropylene; SS = stainless steel. The 1 Y4-in. NPT GFP discharge is 2 718 in. octagonal across flats; the 1 Y4-in. NPT SS discharge is 2 118 in. octagonal across flats, -and the 2-in.
NPT SS discharge is 2 718 in. hexagonal across flats. Discharge is female NPT threaded, U.S. nominal size, to accommodate OrencO discharge hose and valve assemblies. Consult your Orenco Distributor
about fittings to connect hose and valve assemblies to metric -sized piping.
2 Minimum liquid level is for single pumps when installed in an Orenco Biotube® Pump Vault or Universal Flow Inducer. In other applications, minimum liquid level should be top of pump. Consult Orenco for
more information.
3 Weight includes carton and 10-tt (3-m) cord.
4 High-pressure discharge assembly required.
5 Do not use cam -lock option (0) on discharge assembly.
6 Custom discharge assembly required for these pumps. Contact Orenco.
7 Capacitor pack (sold separately or installed in a custom control panel) required for this pump. Contact Orenco.
8 Torque locks are available for all pumps and are supplied with 3-hp and 5-hp pumps.
9 ClickTightrm compatible.
NTD-PU-PF-1 Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com
Rev. 10 © 01 /21
Page 2 of 4

Materials of Construction
Discharge Glass -filled polypropylene or stainless steel
Discharge bearing Engineered thermoplastic (PEEK)
Diffusers Glass -filled PPO (Noryl GFN3)
Impellers Celcon® acetal copolymer on 10-, 20-, and 30-gpm models; 50-gpm impellers are Noryl GFN3
Intake screen Polypropylene
Suction connection Stainless steel
Drive shaft 7/16-in. hexagonal stainless steel, 300 series
Coupling Sintered stainless steel, 300 series
Shell Stainless steel, 300 series
Motor Franklin motor exterior constructed of stainless steel. Motor filled with deionized water and propylene glycol for constant lubrication. Hermetically
sealed motor housing ensures moisture -free windings. All thrust absorbed by Kingsbury -type thrust bearing. Rated for continuous duty. Single-
phase motors are equipped with surge arrestors for added security. Single-phase motors through 1.5 hp (1.11 k" have built-in thermal over-
load protection, which trips at 203-221° F (95-105' Q.
Using a Pump Curve
A pump curve helps you determine the best pump for your system. Pump curves show the relationship between flow and pressure (total dynamic
head or "TDH"), providing a graphical representation of a pump's optimal performance range. Pumps perform best at their nominal flow rate. These
graphs show optimal pump operation ranges with a solid line and show flow rates outside of these ranges with a dashed line. For the most accurate
pump specification, use Orenco's PumpSelecf" software.
Pump Curves
500 1 400
PF10 Series, 60 Hz, 0.5 -1.0 hp PF20 Series, 60 Hz, 0.5 1.5 h
400I _ 350 PF2015
PF1010 —
350
= e 300 --
C300
250
250 PF1007 = PF2010
� ......
'a P�1005
a -- 'a
200 cui "f ate+
200 \\ PF20051 �\
150
= 150
100 \ 100 \
50 y' . '` 50
01
0 2 4 6 8 10 12 14 16 18 0 5 10 15 20 25 30 35
Flow in gallons per minute (gpm) Flow in gallons per minute (gpm)
40
Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com NTD-PU-PF-1
Rev. 10 0 01/21
Page 3 of 4

Pump Curves, Cont.
900
800
as
700
C 600
F.
500
a�
t
400
E
300
4 200
100
0
0
100
90
as
80
c
70
0
60
c,s
50
40
c�
�.
� 30
c 20
10
0
0
■■■L__
■
�MENEM
MEMEEME
MIMMMMM
M
�®
MMMME
MM
MMMMM
5 10 15 20 25 30 35 40 45
Flow in gallons per minute (gpm)
10 20 30 40 50 60 70 80 90 100
Flow in gallons per minute (gpm)
450
400
as
350
c
C 300
250
m
200
= 150
100
50
0
0
PF5050
PF50 Series, 60 Hz, 0.5 - 5.0 hp
PF5030
PF5015
\
PF5010
PF5007
'
PF5005
10 20 30 40 50 60 70 80 90
Flow in gallons per minute (gpm)
Operating Point:
96GPM @ 47 TDH
NTD-PU-PF-1 Orenco Systems° • 800-348-9843 • [phone] • www.orenco.com
Rev. 10 © 01 /21
Page 4 of 4