WI0700035_Other Correspondence_20000128

Peerless Metal Powders & A�.4aives-i`ERIAL SAFETY
124 South Military
Detroit, Michigan 48209
313-841-5400
SECTION I IDENTIFICATION
Product Name: CAST IRON ArGRFGATE
Common Name: _see at a h d product list
CAS No: 65997.19-5
DATA SHEET
Chemical Family: _
Formula: _NLA
Date: ra"� ',-=tyL2R2000
SECTION II INGREDIENTS AND RECOMMENDED OCCUPATIONAL EXPOSURE LIMITS
Material CAS No. Weight % ACGIH TLV Mg/cu in
Iron
Carbon
Manganese
Silicon
Chromium
1309-37-1
90+
5
744044-0
<4.00
3.5
7439-96.5
0.3 - 1.0
5
7440-21-3
<3.0
10
7440-47-3
0.0 - 0.2
0.5
c means ceiling limit.
not be exceeded.
SECTION III PHYSICAL DATA
Melting Point Specific Density Appearance and Odor
base metal - 2750 degrees F 6.7 gm / cc grey particles - no odor
SECTION IV FIRE AND EXPLOSION HAZARD DATA
'Airborne finely dispersed dust will ignite.
These are limits which shall
Extinguishing Media Special Fire Fighting Procedures : Use water only in mist / fog Dry
Dry chemical, dry sand, graphite to smother application-to.avoid.spreading
fire powder or accumulated dust.
Use self-contained breathing
apparatus and protective
SECTION V REACTIVITY.DATA
Stable under normal conditions of storage and transport. Will react with strong oxidizers.
r
SECTION VI HEAL'M HAZARD DATA
r
No potential health hazards other than
X Inhalation
those listed are known Major Exposure Hazard
Skin Contact
X Eye Contact
Indigestion
,Effects of Overexposure
Inhalation - bronchitis, siderosis
Eye Contact. - mechanical irritation
Emergency and First Aid Procedures
inhalation - remove to fresh air
Eye Contact - irrigate eyes to remove dust particles

IECTION VII SPILL OR LEAK PROCEDU 3
avoid generation of airborne dust during clean-up process
Dispose of in accordance with local, state and federal regulations
iECTION Vill SPECIAL PROTECTION INFORMATION
As needed, use approved dust respirator and approved safety goggles ( OSHA 29 CFR 1910.94). Do not use contact lenses.
Ventilation recommended.
bECTION DC SPECIAL PRECAUTIONS
Keep in closed containers. Do not store near strong oxidizers. Use good housekeeping procedures to avoid creating dust.
The in contained herein has been compiled from sources considered reliable and accurate to the best of our
knowledge and belief, but is not guaranteed to be so. it relates only to the product listed.and does not relate to use of the product
in combination with any other material or materials or in a particular processes. Since the use of the MSDS information, the
conditions of use of our product and the environment in which that product is placed are not within the control of Peerless Metal
Powders & Abrasive, it is the user's obligation and duty to determine the conditions of safe use of the products used as well as the
manner in which these products may be affected by the environment in which they may used.
We urge you to review each MSDS to ensure that your uses of the product take into account the current information available on its
potential hazards. It is your responsibility to convey this information to your employees, customers or anyone who may be exposed
to this product. Please check your riles and discard any previous versions as may be applicable. If you have any questions or
:quire additional copies, pleasecontact our Sales Department.

009,0 of Rantec Natural Pviymers
- Galactomannan polymer (guar gum) is a complex carbohydrate derived from the seed of specially
grown bean plants (cyamopsis tetragonoloba). Guar gum carbohydrate is a long chain linear
molecule with a molecular weight of approximately 1,500,000 or greater. The general structure is
shown in Figure 1. Guar gum polymer chains attract and weakly capture water, producing vol-
umes of influence. They also physically tangle with one another in the solution. These phenome-
non produce viscosity of guar gum solutions.
Guar beans are grown primarily in Pakistan and India. The bean plants are harvested and dried
following the growing season. The beans are shelled from the pods, the germ and hull removed.
The resulting splits are wet -milled into powder; granulation and quality grade the powder. Prod-
ucts are re -blended according to specification, bagged and marked.
Rantec purchases a wide range of polymers for use in many industries throughout the world. All
shipments of polymer are given rigorous quality testing and assurance prior to shipment to the end
user. Stocks of polymer are maintained throughout the world.
Rantec markets a number of products based on natural guar gum polymers for mining, explosive,
hydromulching, construction and feedapplication. These include KP4000, KP3000, G150, UFF-
SP and DI. Rantec also supplies a wide range of synthetic polymers.
CHp OH
0
OH
aALACTOSE
OH 0
CH20H CHZ
0 I OIH
MANNOSE _ MANNOSE
Figure 1: Chemical Structure G150 guar gum
G150 Cataiog
5

Rantec G150 TE,`_'Inical Data Sheet
DESCRIPTION
G150 is Rantec's guar -based natural polymer for biopolymer liquid shoring fluids (BLSF) and drill-
ing muds. G150 BLSF is used extensively for geo-technical construction and drilling fluid for oil
- and gas, water well and caissons. Geotechnical applications. include french drain and extraction
trenches, as well as permeable reactive barriers (PRB).t G150 is biodegradable and can be bro-
ken down completely maintaining the permeability granular fill, soils and producing formations.
Rantec has more than 15 years of experience in supplying G150 for use in liquid shoring and drill-
ing applications. As part of Rantec's continued -improvement program G150 is now easier to mix;
less dusty and produces more viscosity per pound.
Viscosity with Concentration VISCOSITY
' r
no
70
E
E 80
so
a40
Z 00
2 20
10
0; i i
20 25 50
05 . .40 45 50 55 80
to0
90
80 x
70 �
80 r
S
So :
40
30
85
Figure 2: Viscosity with Concentration Typi-
cal 2hr
Viscosity, as measured by the Baroid
Rheometer or a Marsh -funnel, is the
most common measure of polymer qual-
ity and the ability of the fluid to stabilize
excavations. Figure 2: Viscosity with
Concentration shows fresh water vis-
cosity for a range of concentrations of
Rantec G150 biopolymer.
RHEOLOGY
igure
kantec 1 BLSF is a non -Newtonian
- • fluid. At lowshear�����.•u
�_��unn.� e�enm��soow
��■��IIII�\■g 1111��■��IIIIvis-
cosity•w. Figure 3 Rhoology
strates these rheological characteristics of
■■11111MEN IG ■1111111 the fluid.
t 10 t00 INN
High viscosity in the gel state or low shear
condition is important for prevention of soil or
water movement, while low viscosity is im-
portant under higher shear conditions such
as mixing and pumping.
G150 fluids immediately recover original viscosity as soon as shear is relieved. High shear will not
destroy the G150 polymer molecule as can occur with many synthetic polymers.
I
Day, D'Hannesin, Marsden, "Geotechnical techniques for the construction of reactive barriers", Journal of Hazardous Materials, B67 (1999),
285-297.
�� . G150 Catalog'::.
6

YIELD AND MIXING
G150.HydraUan Rate
0.00 025 0.50 0.75 1.00 123 im 1.75 2o0
Fl.
ru�,H�s
ability to produce viscosity.
Figure 4: Viscosity Development
Rantec G150 is designed to provide easy
mixing and good yield of viscosity: G150
yields workable viscosity in about 1 hour
and is well yielded in about 4 hours. Figure
4: ,Viscosity Development demonstrates
the development of viscosity through a pe-
riod of 24 hours. In 1 hour G150 has
yielded 90% of its viscosity. G150 responds
well to high shear mixing. Additional shear
will accelerate the rate of viscosity yield and
does not adversely affect the molecule or its
Rantec will provide assistance in choosing equipment suited for good mixing of 43150 fluid. Sys-
tems can be engineered for a wide range of capabilities from manual addition to fully automated
systems. .
PACKAAGJI�LG
Rantec G150 is available in packaging from 20-Ib pails to 2000-Ib super sacks. The most common
packaging is 50-lb multi -wall paper bags. All packages are loaded on pallets and stretch wrapped
to protect the product. For outside storage pallet covers can be provided on request.
SAFETY
G150 is a natural organic polymer often used in food ingredients as well as industrial applications.
It is non-polluting and non -toxic. It is totally biodegradable, so disposal problems are reduced.
Preservative can be used for long term applications: G150 is non -mineral: therefore, it does not
contaminate trenches, surroundings or assays.
File: F:\Iwm\advertis\tds\G150btds.doc
G150 Catalog_
7'
Rantec G150 is available in packaging from 20-Ib pails to 2000-Ib super sacks. The most common
packaging is 50-lb multi -wall paper bags. All packages are loaded on pallets and stretch wrapped
to protect the product. For outside storage pallet covers can be provided on request.
SAFETY
G150 is a natural organic polymer often used in food ingredients as well as industrial applications.
It is non-polluting and non -toxic. It is totally biodegradable, so disposal problems are reduced.
Preservative can be used for long term applications: G150 is non -mineral: therefore, it does not
contaminate trenches, surroundings or assays.
File: F:\Iwm\advertis\tds\G150btds.doc
G150 Catalog_
7'

H 4 M T E C
\•/n
Rantec G150 Specifications
82016
Rantec G150 is a coarse granulation medium viscosity product designed for use in
drilling fluids and liquid shoring slurry for trenching,'as well as flocculent and depres-
sant applications in the mining industry. G150 is generally characterized as a 100
mesh powder that typically yields a cold water viscosity of 3800-4500 cps after hy-
drating for 2 hours. Minimum product specifications insured by Rantec are listed be-
low.
Product Specifications Analysis Method
Moisture 12% Maximum B-M-2.01
Protein 5.8% Maximum B-P-2.01
pH 5.2 to 6.5 Typical C-P-2.01
, Granulation
-T-hrough-80-mesh
90%Minimum 44—.03
Through 100 mesh
75% Minimum
Through 200 mesh
40% Maximum
Through 325 mesh
15% Maximum
Viscosity
minimums
15 Minutes
1500 cps 134-1.036
30 Minutes
2800
1 Hour
3400
2 Hours
3800
24 Hours
90% Minimum of 2 Hour Value
Table 1: G150 Specifications
Rev. 1 Dec. 1997 ©Rantec Corporation 1997
G1511 datalog

RarILdc G150 Blopolymera ASDS
11
1. Product and Company Information
Product Name: Rantec® /Procol® / Viscol® Guar Gum
Manufacturer/Supplier: Rantec Corporation
Address: 17 Kukuchka Lane
Ranchester, WY 82839
Phone Number: [phone]
Fax Number: [phone]
e-mail: rantecalranteccorp.com
2. Composition / Information on Ingredlents
Ingredient CAS % Exposure
Number Weight Limits
Guar Gum 9000-30-0 100 5 mg/m3 (respirable) PEL-TWA
3 mg/m'Irespirable) TLV-TWA
10 mg/m (inhalable dust) TLV-TWA
OSHA Hazardous Material: Yes
OSHA Hazard Categories: Irritant, Sensitizer, Combustible Dust
3. Hazards Identification.
Emergency Overview:
Concentrations of dust suspended in the air present a fire and explosion hazard. Inhalation of dust may cause respi-
ratory irritation and possible lung injury with symptoms of shortness of breath and reduced lung function. Guar gum is
very slippery when wet.
Acute Health Effects:
Eye Contact: Contact may cause irritation based on studies with laboratory animals.
Skin Contact: Contact may cause dryness.
Inhalation: Inhalation of dust may cause irritation of the nose, throat and respiratory passages. Symptoms include
coughing, sore throat, nasal congestion, sneezing wheezing and shortness of breath. May cause life -threatening aller-
gic reaction in susceptible individuals.
Ingestion: DO NOT INGEST. While this product is not toxic by ingestion, swallowing small amounts could cause
complete blockage of the mouth, pharynx, trachea, esophagus and/or gastrointestinal system which may cause chok-
ing, suffocation and/or other life threatening medical conditions. Get medical attention immediately.
Chronic Health Effects: Overexposure to any nuisance dust may cause lung injury. Symptoms include cough, short-
ness of breath and reduced pulmonary function
Carcinogenicity: None of the components of this product are listed as carcinogens or suspected carcinogens by
OSHA, IARC or NTP.
Medical Conditions Aggravated by Exposure: Persons with pre-existing skin and respiratory disorders may be at an
increased risk from exposure.
G150 Catalog,
13

' �4: FirslAid'•Measures� � -
Eye: Flush immediately with large amounts of water. Eyelids should be held away from the eyeball to ensure thorough
rinsing. If irritation persists get medical attention.
•
Skin: First aid is not normally needed. Wash exposed skin with soap and water after use. If irritation or rash develops
get medical attention. Use skin lotion if dryness occurs.
I
Inhalation: If symptoms of irritation or allergy develop, remove person from source of exposure to fresh air. If symp-
toms persist get medical attention.
Ingestion: Swallowing even small amounts may have serious, life -threatening effects. Get immediate medical atten-
tion.
I 5: Firefighting Measures
Flashpoint: Not Applicable Lower Explosion Limit: 0.040 ortcf
Autoignition Temperature: Not Determined Upper Explosion Limit: Not determined
" Extinguishing Media: Use water fog, dry chemical, carbon dioxide or foam. Do not use streams of water as dust dis-
persed by water streams can explode.
Special Fire Fighting Procedures: Wear positive pressure, self-contained breathing apparatus and full protective
clothing.
Unusual Fire and Explosion Hazards: Powder has the potential to form explosive mixtures with air. Avoid creating
dust. Keep away from heat, sparks and open flames. As with all dusty materials, use preventative measures including
spark proof motors and ventilation to control dust.
Combustion Products: Oxides of carbon and'nitrogen.
6: Accidental Release Measures
_.
Wear appropriate protective clothing and equipment. Caution: Guar gum is very slippery when wet. Sweep up or vac-
uum, avoiding the creation of airborne dust, and collect into a suitable container for disposal. Keep spilled product
away from flammable and combustible materials. Wash residual traces with hot water after sweep -up is complete.
Test area for residual slippery conditions.
- 4'HandIffig and storage
Handling: Avoid generating and breathing dust. Avoid eye contact: Use with adequate local exhaust ventilation and
dust collection to maintain the concentration of airbome dust below the exposure limits. If clothing becomes contami-
nated, remove and launder before re -use. Wash.thoroughly after handling.
Storage: Keep product dry. Store in a cool, dry area. Keep containers closed to avoid moisture absorption.
I 6:,Exposure Controls I Personal Protection
Engineering Controls: Use explosion proof local exhaust ventilation as needed to maintain exposure concentrations
below the recommended limits.
Personal Protective Equipment (PPE): Eye Protection: Safety glasses or goggles recommended.
Skin Protection:- Rubber, plastic or leather gloves recommended.
del G150 Catalog

8. Exposure Controls / Personal Protection continued
Respiratory Protection: If the concentrations exceed the Threshold Value Limit (TLV), a NIOSH approved dust respi-
rator, supplied air respirator or self-contained breathing apparatus is recommended. Select appropriate respiratory
protection for respirable particulates based on consideration of the airborne workplace concentrations and duration of
�l exposure. Select and use respirators in accordance with 29 CFR 1910.134 bttn://www.access.apo.gov/nara/cfr/cfr-
retrieve.htn0yaeel , ANSI Z88.2 http://www.ansi.ore/, the NIOSH Respirator Decision Logic and good industrial hygiene
practice h"://www.cdc.gov/niosh/homet)ajze.
9. Physical and Chemical Properties
Boiling Point: Not Applicable Specific Gravity: Not applicable
- Melting Point: Decomposes % Volatile: Not applicable
Vapor Pressure: Not Applicable Evaporation Rate (Butyl Acetate=11): Not Applicable
Vapor Density (Aimll): Not Applicable pH: 5-8
% Solubility In Water: Complete OctanollWater Partition Coefficient: Not Applicable
Odor/Appearance: Creamy white powder with a bean -like odor.-
10. Stability and Reactivity
Stability: Material is stable.
Incompatibility: Avoid high temperatures, sparks, open flames and moisture. Avoid contact with strong oxidizing
agents.
Hazardous Reactions -Decomposition Products: Combustion may produce carbon dioxide, carbon monoxide and
oxides of nitrogen.
Hazardous Polymerization: Will not occur.
11. Toxicological Information
Guar Gum: Oral rat LD50: 9.4g/kg
Guargum-is-a-natural-food-additive,-although-direct-use-in-pawderzT pilt-form-19-ba�d—y the-FDXdue-to the risk of
respiratory or gastrointestinal blockage
No ecotoxicity, data -is available at this time.
12. Ecoloctical Information
13. Disposal Considerations
Dispose in compliance with all applicable federal, state and local regulations. Do not dump down sewers or drains as
F this may cause blockage.
14. Transport Information
U.S. Department of Transportation (DOT)
Proper Shipping Name: Not Regulated
Hazard Class: N/A
UN/NA Code: N/A
Packing Group: N/A
Labels Required: N/A
--I
�I G150 Catalog
15

14. Transport Information (continued)
IMDG CODE
Proper Shipping Name: NOT REGULATED
Hazard Class: N/A
UN/NA Code: N/A
Packaging Group: N/A
Labels Required: N/A
15. Regulatory Information
Regulatory Information
-, The_United States Food and Drug Administration, the European Economic Community and the World Health
Organization accept guar gum as a food additive/ingredient providing it meets specified purity standards and
-_ dosage limitations. Maximum usage levels permitted may vary from country to country. Guar gum has been
affirmed as GRAS by the United States Food & Drug Administration under title 21, CFR, part 184.1339; it is
listed as item G.3 of Table IV, Division 16, of the Canadian Food and Drug Regulations and is referenced E-412
under the EEC Council Directives.
Comprehensive Environmental Response and Liability Act of 1980 (CERCLA) Reportable Quantity:
This product is not subject to CERCLA reporting requirements as it is sold.
OSHA Hazard Categories: Irritant,, Sensitizer, Combustible Dust
Superfund Amendments and Reauthorization Act (SARA) Title III Information:
SARA Section 311/312 Hazard Categories: Fire Hazard, Acute Health
This product contains the following toxic chemical(s) subject to reporting requirements of SARA
l Section 313: None
California Proposition 65: This product is not known to contain chemical regulated under California Prop. 65.
Toxic Substances Control Act (TSCA): All components of this product are listed on the TSCA inventory or exempt
from notification requirements.
Canadian Environmental Protection Act: All of the components of this products are listed on the Canadian
Domestic Substances List or exempt from notification requirements.
European Inventory of Existing Commercial Chemical Substances (EINECS): All of the components of this
product are listed on the EINECS Inventory or exempt from notification requirements.
Japan MITI: All of the components of this product are existing chemical substances as defined in the Chemical
Substance Control Law.
Australian Inventory of Chemical Substances: All of the components of this product are listed on the AICS
Inventory or exempt from notification requirements.
Canadian WHMIS Classification: Class B, Division 4 (Flammable Solid)
NFPA Hazard Ratings:
Health: 1
HMIS Hazard Ratings:
Flammability: 1
16. Other Information
Reactivity: 0
G1'50 CatAl
1G ",.

a
Health: 1 Flammability:l Reactivity: 0
Abbreviations:
- ACGIH
American Conference Of Governmental Industrial Hygienists
ANSI
American National Standards Institute
CAS
Chemical Abstracts Service
CDC
Centers for Disease Control and Prevention
CFR •
The Code of Federal Regulations
EEC
European Economic Community
EINECS
European Inventory of Existing Commercial Chemical Substances
EPA'
United States Environmental Protection Agency
FDA
United States Food and Drug Administration
HMIS
Hazardous Materials Identification System
IARC
International Agency for Research on Cancer
IMDG
International Maritime Dangerous Goods
LD50
Lethal Dose expected to cause death in 50% of the test animals
MITI
Ministry of International Trade and Industry
NFPA
National Fire Protection Association
NIOSH
CDC - National Institute for Occupational Safety
NTP
National Toxicological Program
OSHA
U.S. Department of Labor, Occupational safety and health administration
PEL
OSHA - permissible exposure limit
TLV
ACGIH -threshold limit value
TWA
Time weighted average.
- UN/NA
United Nations / North America
US
United States
WHMIS
Workplace Hazardous Materials Information System
Rantec, Procol, Viscol and the-Rantec world symbol are registered trademarks rof Rantec
Corporation and Polypro International.

Page 1 of 5
EYTEC MSDS No: 06481
Date: 12/21 /1999
MATERIAL SAFETY DATA Supersedes: 07/0111997
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: SUPERFLOC®A-130 HMW Flocculant
SYNONYMS: None
CHEMICAL FAMILY: Anionic polyacrylamide
MOLECULAR FORMULA: Polymer
MOLECULAR WGT: Polymer
CYTEC INDUSTRIES INC., FIVE GARRET MOUNTAIN PLAZA, WEST PATERSON, NEW JERSEY 07424,
USA
For Product Information call 1-800/652-6013. Outside the USA and Canada call 1-973/357-3193.
EMERGENCY PHONE: For emergency involving spill, leak, fire, exposure or accident call CHEMTREC:
1-800/424-9300. Outside the USA and Canada call 1-703/527-3887.
2. COMPOSITION/INFORMATION ON INGREDIENTS
OSHA REGULATED COMPONENTS
COMPONENT CAS. NO. % TWA/CEILING REFERENCE
No Permissible
Exposure Limits
(PEL/TLV) have
been established
by OSHA or ACGIH.
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
APPEARANCE AND ODOR: Off-white granular solid
STATEMENTS OF HAZARD:
IMPORTANT! SPILLS OF THIS PRODUCT ARE VERY SLIPPERY WHEN WET
POTENTIAL HEALTH EFFECTS
EFFECTS OF OVEREXPOSURE:
Acute oral (rat) and dermal (rabbit) LD50 values are estimated to be greater than 5.0 g/kg amd 2.0 g/kg,
respectively. The 4-hour LC50 (rat) value is estimated to be greater 20 mg/L.
Direct contact with this material may cause minimal eye and skin irritation.
4. FIRST AID MEASURES
Material is not expected to be harmful by ingestion. No specific first aid measures are required.
In case of skin contact, wash affected areas of skin with soap and water.
In case of eye contact, immediately irrigate with plenty of water for 15 minutes.
Material is not expected to be harmful if inhaled. If inhaled, remove to fresh air.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
FLASHPOINT: Notapplicable

SUPERFLOC® A-130 HMW Flocculant MSDS No: 06481
Date: 12/21/1999
Page 2 of 5
FLAMMABLE LIMITS
(% BY VOL): Not applicable
AUTOIGNITION TEMP: <302 F; 150 C
DECOMPOSITION TEMP: <302 F; 150C
EXTINGUISHING MEDIA AND FIRE FIGHTING INSTRUCTIONS
Use water spray, carbon dioxide or dry chemical to extinguish fires. Use water to keep containers cool.
Wear self-contained, positive pressure breathing apparatus.
6. ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Spilled material becomes very slippery when wet. Sweep up spills and place in a waste disposal container.
Flush the area thoroughly with water and scrub to remove residue. If slipperiness remains, apply more
dry -sweeping compound. Do not flush large quantities of the material to sewer.
7. HANDLING AND STORAGE
Spills should be scooped up or wiped up immediately, and the spill area flushed with water.
To avoid product degradation and equipment corrosion, do not use iron, copper or aluminum containers or
equipment.
1
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE)
j Engineering controls are not usually necessary if good hygiene practices are followed. Before eating, drinking,
or smoking, wash face and hands thoroughly with soap and water.Avoid unnecessary skin contact. Impervious
gloves are recommended to prevent prolonged skin contact. For operations where eye or face contact can
9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE AND ODOR: Off-white granular solid
BOILING POINT: Not applicable
MELTING POINT: Not available
VAPOR PRESSURE: Not applicable
SPECIFIC GRAVITY: 0.75-0.95
VAPOR DENSITY: Not applicable
% VOLATILE (BY WT): 10-13; (water)
DH: Not apDlicable
SATURATION IN AIR (% BY VOL): Not available
EVAPORATION RATE: Not applicable
SOLUBILITY IN WATER: Limited by viscosity
VOLATILE ORGANIC CONTENT: Not available
10. STABILITY AND REACTIVITY
STABILITY. Stable
CONDITIONS TO AVOID: None known)
POLYMERIZATION: Will Not Occur

SUPERFLOCO A-130 HMW Flocculant MSDS No: 06481 Date: 12/21/1999 Page 3 of 5
CONDITIONS TO AVOID: None known
INCOMPATIBLE MATERIALS: Strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: carbon dioxide; carbon monoxide; ammonia; oxides of
nitrogen
11. TOXICOLOGICAL INFORMATION
Toxicological information for the product is found under Section 3. HAZARDS IDENTIFICATION. Toxicological
_ information on the OSHA regulated components of this product is as follows:
This product contains, no OSHA regulated (hazardous) components.
_ California Proposition 65 Warning (applicable in California only) - This product contains (a) chemical(s) known to
the State of California to cause cancer.
12. ECOLOGICAL INFORMATION
No aquatic LC50, BOD, or COD data available.
OCTANOL/1-120 PARTITION COEF.: Not applicable
13. DISPOSAL CONSIDERATIONS
The information on RCRA waste classification and disposal methodology provided below applies only to the
Cytec product, as supplied. If the material has been altered or contaminated, or it has exceeded its
recommended shelf life, the guidance may be inapplicable. Hazardous waste classification under federal
regulations (40 CFR Part 261 at seq) is dependent upon whether a material is a RCRA "listed hazardous waste"
or has any of the four RCRA "hazardous waste characteristics." Refer to 40 CFR Part 261.33 to determine if a
given material to be disposed of is a RCRA "listed hazardous waste"; information contained in Section 15 of this
MSDS is not intended to indicate if the product is a "listed hazardous waste." RCRA Hazardous Waste
Characteristics: There are four characteristics defined in 40 CFR Section 261.21-61.24: Ignitability, Corrosivity,
Reactivity, andToxicity. Tc determine lanitabili , see Section 5 of this MSDS (flash point). For Corrosivity, see
Sections 9 and 14 (pH and DOT cormsivity). For Reactivity, see Section 10 (Incompatible materials). t-or
Toxicity, see Section 2 (composition). Federal regulations are subject to change. State and local requirements,
which may differ from or be more stringent than the federal regulations, may also apply to the classification of
the material if it is to be disposed. Cytec encourages the recycle, recovery and reuse of materials, where
permitted, as an alternate to disposal as a waste. Cytec recommends that organic materials classified as RCRA
hazardous wastes be disposed of by thermal treatment or incineration at EPA approved facilities. Cytec has
provided the foregoing for information only; the person generating the waste is responsible for determining the
waste classification and disposal method.
14.TRANSPORT
INFORMATION
SHIPPING
NAME:
This section provides basic shipping classification information. Refer to appropriate
transportation regulations for specific requirements.
D.O.T.
SHIPPING INFORMATION
NOT APPLICABLE/NOT REGULATED
IMO
SHIPPING INFORMATION
NOT APPLICABLE/NOT REGULATED
HAZARD CLASS/
Not Applicable
Not Applicable
PACKING
GROUP:
UN NUMBER:
Not Applicable
Not Applicable
— IMDG PAGE:
Not Applicable
Not Applicable
D.O.T.
(PRODUCT REPOWABLEOUAWIT1)
Not Applicable
HAZARDOUS
Not Applicable
- SUBSTANCES:

SUPERFLOC® A-130 HMW Flocculant MSDS No: 06481 Date: 12/21/1999 Page 4 of 5
TRANSPORT None Required
LABEL
REQUIRED:
None Required
ICAO/IATA TRANSPORT CANADA
SHIPPING NOT APPLICABLE/NOT REGULATED NOT APPLICABLE/NOT REGULATED
NAME:
HAZARD CLASS: Not Applicable Not Applicable
SUBSIDIARY Not Applicable Not Applicable
CLASS:
UN/ID Not Applicable Not Applicable
NUMBER:
PACKING
Not Applicable
Not Applicable
GROUP:
TRANSPORT
None Required
None Required
LABEL
REQUIRED:
PACKING INSTR:
PASSENGER Not Applicable
Not Applicable
CARGO Not. Applicable
MAX.NET QTY:
PASSENGER Not Applicable
Not Applicable
cARGo Not Applicable
ADDITIONAL TRANSPORT INFORMATION
TECHNICAL Not Applicable
NAME (N.O.S.):
15,REGU1r9t0RY__ W0RMATION
INVENTORY INFORMATION
US TSCA: All components of this product are included on the TSCA Inventory in compliance with the
Toxic Substances Control Act, 15 U. S. C. 2601 et. seq.
CANADA DSL: Components of this product have been reported to Environment Canada in accordance
with subsection 25 of the Canadian Environmental Protection Act and are included on the
Domestic Substances List.
EEC EINECS: All components of this product are included in the European Inventory of Existing
Chemical Substances (EINECS) or are polymers of which the components are in
EINECS, in compliance with Council Directive 67/548/EEC and its amendments.
OTHER The following components of this product may be subject to reporting requirements
ENVIRONMENTAL pursuant to Section 313 of CERCL.A (40 CFR 372), Section 12(b) of TSCA, or may
INFORMATION be subject to release reporting requirements (40 CFR 307,-40 CFR 311, etc.) See
Section 13 for information on waste classification and waste disposal of this product.
COMPONENT
This product does
not contain any
components regulated
under these sections
of the EPA
CAS. NO. %
RQ(Ibs) S313 TSCA 12B

SUPERFLOC® A-130 HMW Flocculent MSDS No: 06481 Date: 1212111999 Page 5 of 5
PRODUCT CLASSIFICATION UNDER SECTION 311 OF SARA
Not Applicable under SARA TITLE III
16. OTHER INFORMATION
NFPA HAZARD RATING (National Fire Protection Association)
Fire FIRE: Materials that must be preheated before ignition can occur.
1 HEALTH: Materials which on exposure under fire conditions would offer no hazard
Health 0 0 Reactivity . beyond that of ordinary combustible material.
REACTIVITY: Materials which in themselves are normally stable, even under fire
Special exposure conditions, and which are not reactive with water.
REASON FOR ISSUE:
Revised Section 4,5,9 & 10
Randy Deskin, Ph.D., DABT
This information is given without any warranty or representation. We do not assume any legal responsibility for same, nor do we
give permission, inducement, or recommendation to practice any patented invention without a license. It is offered solely for your
consideration, investigation and verification. Before using any product, read its label.