1812_DukeMarshall_Phase4_Piezo_DrillerAbandonmentReport_FID1997631_20250404

March 31, 2025
Duke Energy Marshall Steam Station
8320 NC Hwy 150 E
Terrell, North Carolina 28673
Attention: Ms. Ashley Healy, P.G.
EHS Waste and Groundwater Programs, Duke Energy
Reference: Completion Report for Monitoring Well Abandonments
Duke Energy Marshall Steam Station
Catawba County, North Carolina
S&ME Project No. 21410007, Ph. 02
Dear Ms. Healy:
S&ME, Inc. (S&ME) is pleased to present this Completion Report (hereafter, Report) for the abandonment of four
(4) monitoring wells in support of the ash basin excavation and landfill construction at Duke Energy's Marshall Steam
Station (hereafter, Site), located at 8320 NC Hwy 150 E, in Catawba County, North Carolina. This Report summarizes
the well abandonment activities performed by S&ME at the Site on March 4, 2025 and March 20, 2025, as well as a
certification statement signed by a North Carolina licensed geologist, Skyler Schmal, P.G, certifying that each
monitoring well was abandoned in compliance with the applicable standards and guidance as discussed in this
Report.
Background and Summary
The four (4) monitoring wells addressed in this Report were abandoned by a North Carolina registered well driller
on March 41", 2025 and March 201", 2025. Each of these monitoring wells was abandoned in accordance with the
75A NCAC 02C Section .07 73 Standards for the Abandonment of Wells (hereafter, 02C Standards). S&ME personnel
provided support and oversight during the abandonment process for each monitoring well to ensure compliance
with the 02C Standards as mentioned above.
The four (4) monitoring wells included in this Report (shown on Figure 1 in Attachment 1) were abandoned due to
their location within, or adjacent to, the grading and earthwork limits on Site supporting the excavation of ash, as
well as other various earthwork operations supporting the construction of the Industrial Landfill Future Phases. In
accordance with the 02C Standards, a well must be permanently abandoned if it acts as a source or channel of
contamination. Each of these wells were abandoned prior to earthwork and grading operations to reduce the
likelihood that the wells would act as a channel for contaminants to reach groundwater once the well was removed
during excavation and earthwork activities.
A summary of pertinent monitoring well information for each of the wells abandoned is located in Table 1 in
Attachment 11. As required by the 02C Standards, a Well Abandonment Record (GW-30 Form) was completed and
signed for each of the four (4) wells abandoned. S&ME submitted these GW-30 Forms to the North Carolina
S&ME, Inc. 12016 Ayrsley Town Blvd., Suite 2-A I Charlotte, NC 282731 p 704.523.4726 1 www.smeinc.com

Completion Report for Monitoring Well Abandonments
Duke Energy Marshall Steam Station
S&ME Project Number 21410007, Ph. 02
March 31, 2025
Page 2
Department of Environmental Quality (NCDEQ) — Information Processing Unit, and they are included in Attachment
III as reference.
Each of the monitoring wells was abandoned following the general steps listed below:
If present, any dedicated tubing, pumps, or transducers were removed from the well and left on -Site with Duke
Energy personnel.
Depth of water from the ground surface was measured using an electronic water level meter. The bottom of
each well was also tagged to ensure no discrepancies between recorded and actual well depth data exist.
The volume of water in the well was calculated based on the measured water level.
Each well was abandoned using coated bentonite pellets (rather than Quik-Grout) in accordance with the
general requirements of 02C Standards, as access to these wells was very limited at the time of abandonment.
This method was chosen to ensure that bentonite materials made it to the bottom of each well and that no
bridging off would occur.
S&ME understands that the general earthwork contractor on Site will remove the protective well covers and concrete
pads from each of the four (4) abandoned well locations.
Monitoring Well Abandonment Certification
Each of the four (4) monitoring wells discussed in this Report was abandoned in general accordance with the
requirements of the 02C Standards by certified well -drillers licensed in the State of North Carolina. Under the
supervision of an S&ME licensed geologist, an S&ME professional was on site to observe each well abandonment.
Closure
S&ME appreciates each and every opportunity to be of service to Duke Energy. Please contact us if you have any
questions regarding this report.
Sincerely,
5&ME, Inc.
Jasmine Tayouga, E.I.
Project Manager/Team Lead
[e-mail]
Attachments:
I — Figures
II — Tables
III — Well Abandonment Records/GW-30 Forms
V
Skyler Schmal, P.G.
Project Geologist
[e-mail]
�N CgRO •.
• SEAL =
N 2974 -�:
S&ME, Inc.

Attachments

Attachment I — Figures

Drawing Path: T:\Asheville-1410\Projects\2021\21410007 Duke Marshall CCP Closure On -Call Services Terrell NC\02_WelI Abandon ments\March2025\GIS\Draft_Marc h25_Ana ndos.mxd plotted by SkylerRay 03-26-2025
N
�' - � ■ CLF=401 -� CLF=407
1LF, 406
�- � ,.� •� � `.�,}� / � . ' `ono,
• k4 i 400,
`'` � �� CLF-405 ' � ` 3 ' • f Gov, r/ � /� �
t. f
LEGEND
300 600 MONITORING WELLS ABANDONED ON 3/4/2025
(FEET) MONITORING WELL ABANDONED ON 3/20/2025
■r► - a �:. ill. sty..
REFERENCE: R p rtc ■ ■ ■� APPROXIMATE INDUSTRIAL LANDFILL (ILF) PHASE BOUNDARIES (PERMIT NO. 1812)
THIS MAP IS FOR INFORMATIONAL PURPOSES ONLY. PREVIOUSLY ABANDONED ��
AND/OR REMOVED MONITORING WELLS ARE NOT SHOWN ON THIS MAP AERIAL APPROXIMATE 1804 PH. II LANDFILL BOUNDARY (PERMIT NO. 1804)
IMAGERY DATE: 02-25-2025. ALL FEATURE LOCATIONS DISPLAYED ARE ' 19 �
spa APPROXIMATE ASBESTOS LANDFILL BOUNDARY (PERMIT NO. 1804)
APPROXIMATED. THEY ARE NOT BASED ON CIVIL SURVEY INFORMATION, UNLESS
STATED OTHERWISE. �:'j= .— APPROXIMATE ASH BASIN BOUNDARY
rss -
SCALE: FIGURE NO.
MONITORING WELL ABANDONMENTS (MARCH 2O25) 1 " = 300 '
DATE:
III E DUKE ENERGY - MARSHALL STEAM STATION 3-31-2025
CATAWBA COUNTY, NORTH CAROLINA PROJECT NUMBER
21410007. PH.

Attachment II — Tables

Table 1: Summary of Monitoring Well Abandonments in March 202S
Duke Energy - Marshall Steam Station
S&ME Project No. 27470007, Ph. 02
Depth to Water
Total Well
Casing Stick -Up
Total Well Depth
Screened Interval 3
Northing 4
Easting 4
Date
Prior to
Well ID'
Depth Z
Height
(ft-bgs)
(ft-bgs)
(ft-NAD83)
(ft-NAD83)
Abandoned
Abandonment
(ft-toc)
(ft-ags)
(ft-toc)
CLF-401
42.0
3.0
39.0
29.0 to 39.0
685797.3
1412775.8
3/4/2025
32.7
CLF-405
45.0
3.0
42.0
32.0 to 42.0
684921.6
1413021.2
3/20/2025
35.6
CLF-406
46.2
3.2
43.0
33.0 to 43.0
685491.8
1412724.0
3/4/2025
21.1
CLF-4075
46.0
0.6
45.4
33.0 to 43.0
685798.5
1413229.2
3/4/2025
DRY
Notes:
1 Each monitoring well consisted of 2-inch inner diameter inner polyvinyl chloride (PVC) casing
z Total Well Depth - prior to abandonment, the depth to the bottom of the screened interval was measured on each well
3 Screened intervals were recorded from information on the well tag at each location
4 Northing and Easting coordinates provided by Duke Energy
5CLF-407 total well depth may vary due to changing site conditions and continued earthwork within the Ash Basin at Marshall Steam Station
ft: feet
ags: above ground surface
bgs: below ground surface
NAD83: North American Datum 1983
toc: top of casing

Attachment III - Well Abandonment Records/GW-30 Forms

WELL ABANDONMENT RECORD
1. Well Contractor Information:
Jay Little
Well Contractor Name (or well owner personally abandoning well on his/her property)
2717-A
NC Well Contractor Certification Number
SWE
Company Name
2. Well Construction Permit #: Not Applicable
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) ifknown
3. Well use (check well use):
Water Supply Well:
❑Agricultural
❑Municipal/Public
❑Geothermal (Heating/Cooling Supply)
❑Residential Water Supply (single)
❑Industrial/Commercial
❑Residential Water Supply (shared)
❑hri ation
Non -Water Supply Well:
RMonitoring
❑Recovery
Injection Well:
El Aquifer Recharge
[]Groundwater Remediation
❑Aquifer Storage and Recovery
El Salinity Barrier
❑Aquifer Test
❑Stormwater Drainage
❑Experimental Technology
❑Subsidence Control
❑Geothermal (Closed Loop)
[--]Tracer
❑Geothermal (Heating/Cooling Return)
❑Other (explain under 7g)
4. Date well(s) abandoned.
3/4/2025
5a. Well location:
Duke Energy Carolinas Not Applicable
Facility/Owner Name Facility ID# (if applicable)
8320 NC Hwy 150, Terrell, NC 28673
Physical Address, City, and Zip
Catawba 461803426350
County
Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
35.618279 N 80.975991 W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) ifavailable. For multiple injection or non -water supply wells
ONLY with the same constructionlabandonment, you can submit one form.
6a. Well ID#: CLF-401
6b. Total well depth: 39.0 (ft.)
6c. Borehole diameter: 8.0 (in.)
6d. Water level below ground surface: 29.7
6e. Outer casing length (if known): Not applicable
6f. Inner casing/tubing length (if known): 29.0 (ft.)
6g. Screen length (if known): 1 0.0 (ft.)
For Internal Use ONLY:
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed -Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned: Not Applicable
7b. Approximate volume of water remaining in well(s): 1 .53 gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
❑ Neat Cement Grout S Bentonite Chips or Pellets
❑ Sand Cement Grout
❑ Concrete Grout
❑ Specialty Grout
❑ Bentonite Slurry
❑ Dry Clay
❑ Drill Cuttings
❑ Gravel
❑ Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
75 lb
7g. Provide a brief description of the abandonment procedure:
Coated bentonite pellets were gradually added to
the well until top of water column was reached (50 Ibs).
3/8" coarse sodium bentonite chips were gradually added
above the water column to the top of the PVC pipe (25 Ibs).
8. Certification:
3/26/25
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 1 SA NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Iniection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
loc. For Water Supply & Iniection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016

WELL ABANDONMENT RECORD
1. Well Contractor Information:
Jay Little
Well Contractor Name (or well owner personally abandoning well on his/her property)
2717-A
NC Well Contractor Certification Number
SWE
Company Name
2. Well Construction Permit #: Not Applicable
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) ifknown
3. Well use (check well use):
Water Supply Well:
❑Agricultural
❑Geothermal (Heating/Cooling Supply)
❑ Industrial/Commercial
❑ hrigation
Non -Water Supply Well:
El Aquifer Recharge
❑Aquifer Storage and Recovery
❑Aquifer Test
❑Experimental Technology
❑Geothermal (Closed Loop)
❑Geothermal (Heating/Cooling
4. Date well(s) abandoned:
❑Municipal/Public
❑Residential Water Supply (single)
❑Residential Water Supply (shared)
El Groundwater Remediation
El Salinity Barrier
❑ Stormwater Drainage
❑Subsidence Control
[--]Tracer
❑Other (explain under 7g)
3/20/2025
5a. Well location:
Duke Energy Carolinas Not Applicable
Facility/Owner Name Facility ID# (if applicable)
8320 NC Hwy 150, Terrell, NC 28673
Physical Address, City, and Zip
Catawba 461803426350
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
35.6158870 N 080.9751070 W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) ifavailable. For multiple injection or non -water supply wells
ONLY with the same constructionlabandonment, you can submit one form.
6a. Well ID#: CLF-405
6b. Total well depth: 42.0 (ft.)
6c. Borehole diameter: 8.0 (in.)
6d. Water level below ground surface: 35.6
6e. Outer casing length (if known): Not applicable
6f. Inner casing/tubing length (if known): 32.0 (ft.)
6g. Screen length (if known): 1 0.0 (ft.)
For Internal Use ONLY:
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed -Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned: Not Applicable
7b. Approximate volume of water remaining in well(s): 1 .55 gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
❑ Neat Cement Grout S Bentonite Chips or Pellets
❑ Sand Cement Grout ❑ Dry Clay
❑ Concrete Grout ❑ Drill Cuttings
❑ Specialty Grout ❑ Gravel
❑ Bentonite Slurry ❑ Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
88 lb
7g. Provide a brief description of the abandonment procedure:
Coated bentonite pellets were gradually added to
the well until top of water column was reached (50 Ibs).
3/8" coarse sodium bentonite chips were gradually added
above the water column to the top of the PVC pipe (38 Ibs).
8. Certification:
3/26/25
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 1 SA NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Iniection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
loc. For Water Supply & Iniection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016

WELL ABANDONMENT RECORD
1. Well Contractor Information:
Jay Little
Well Contractor Name (or well owner personally abandoning well on his/her property)
2717-A
NC Well Contractor Certification Number
SWE
Company Name
2. Well Construction Permit #: Not Applicable
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) ifknown
3. Well use (check well use):
Water Supply Well:
❑Agricultural
❑Municipal/Public
❑Geothermal (Heating/Cooling Supply)
❑Residential Water Supply (single)
❑Industrial/Commercial
❑Residential Water Supply (shared)
❑hri ation
Non -Water Supply Well:
RMonitoring
❑Recovery
Injection Well:
El Aquifer Recharge
[]Groundwater Remediation
❑Aquifer Storage and Recovery
El Salinity Barrier
❑Aquifer Test
❑Stormwater Drainage
❑Experimental Technology
❑Subsidence Control
❑Geothermal (Closed Loop)
[--]Tracer
❑Geothermal (Heating/Cooling Return)
❑Other (explain under 7g)
4. Date well(s) abandoned.
3/4/2025
5a. Well location:
Duke Energy Carolinas Not Applicable
Facility/Owner Name Facility ID# (if applicable)
8320 NC Hwy 150, Terrell, NC 28673
Physical Address, City, and Zip
Catawba 461803426350
County
Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
35.617437 N 80.976145 W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) ifavailable. For multiple injection or non -water supply wells
ONLY with the same constructionlabandonment, you can submit one form.
6a. Well ID#: CLF-406
6b. Total well depth: 43.0 (ft.)
6c. Borehole diameter: 8.0 (in.)
6d. Water level below ground surface: 17.85
6e. Outer casing length (if known): Not applicable
6f. Inner casing/tubing length (if known): 33.0 (ft.)
6g. Screen length (if known): 1 0.0 (ft.)
For Internal Use ONLY:
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed -Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned: Not Applicable
7b. Approximate volume of water remaining in well(s): 4.1 2 (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
❑ Neat Cement Grout S Bentonite Chips or Pellets
❑ Sand Cement Grout
❑ Concrete Grout
❑ Specialty Grout
❑ Bentonite Slurry
❑ Dry Clay
❑ Drill Cuttings
❑ Gravel
❑ Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
80 lb
7g. Provide a brief description of the abandonment procedure:
Coated bentonite pellets were gradually added to
the well until top of water column was reached (50 Ibs).
3/8" coarse sodium bentonite chips were gradually added
above the water column to the top of the PVC pipe (30 Ibs).
8. Certification:
3/26/25
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 1 SA NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Iniection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
loc. For Water Supply & Iniection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016

WELL ABANDONMENT RECORD
1. Well Contractor Information:
Jay Little
Well Contractor Name (or well owner personally abandoning well on his/her property)
2717-A
NC Well Contractor Certification Number
SWE
Company Name
2. Well Construction Permit #: Not Applicable
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) ifknown
3. Well use (check well use):
Water Supply Well:
❑Agricultural
❑Geothermal (Heating/Cooling Supply)
❑ Industrial/Commercial
❑ hrigation
Non -Water Supply Well:
El Aquifer Recharge
❑Aquifer Storage and Recovery
❑Aquifer Test
❑Experimental Technology
❑Geothermal (Closed Loop)
❑Geothermal (Heating/Cooling
4. Date well(s) abandoned:
❑Municipal/Public
❑Residential Water Supply (single)
❑Residential Water Supply (shared)
El Groundwater Remediation
El Salinity Barrier
❑ Stormwater Drainage
❑Subsidence Control
[--]Tracer
❑Other (explain under 7g)
3/4/2025
5a. Well location:
Duke Energy Carolinas Not Applicable
Facility/Owner Name Facility ID# (if applicable)
8320 NC Hwy 150, Terrell, NC 28673
Physical Address, City, and Zip
Catawba 461803426350
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
35.618307 N 80.974466 W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) ifavailable. For multiple injection or non -water supply wells
ONLY with the same constructionlabandonment, you can submit one form.
6a. Well ID#: CLF-407
6b. Total well depth: 45.4 (ft.)
6c. Borehole diameter: 8.0 (in.)
6d. Water level below ground surface: DRY (ft.)
6e. Outer casing length (if known): Not applicable (ft.)
6f. Inner casing/tubing length (if known): 35.4 (ft.)
6g. Screen length (if known): 1 0.0 (ft.)
For Internal Use ONLY:
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed -Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned: Not Applicable
7b. Approximate volume of water remaining in well(s): D RY gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
❑ Neat Cement Grout S Bentonite Chips or Pellets
❑ Sand Cement Grout ❑ Dry Clay
❑ Concrete Grout ❑ Drill Cuttings
❑ Specialty Grout ❑ Gravel
❑ Bentonite Slurry ❑ Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
70 lb
7g. Provide a brief description of the abandonment procedure:
3/8" coarse sodium coated bentonite pellets were gradually
added to the well until they reached the top of the PVC casing.
8. Certification:
3/26/25
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 1 SA NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Iniection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
loc. For Water Supply & Iniection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016