FA-3270_29451_CA_WR_20240509_MWs Abandonment

1044 Washington Street
Raleigh, NC 27605
[phone]

www.CatlinUSA.com
Wilmington, NC | Raleigh, NC | Washington, NC | Atlanta, GA

E N V I RO N M E N TA L | C I V I L | G E O T E C H N I C A L

Wilmington, NC | Raleigh, NC | Washington, NC | Atlanta, GA | Charleston, SC

May 9, 2024

North Carolina Department of Environmental Quality
Division of Waste Management
UST Section
Attn: Mr. Hassan Osman
1646 Mail Service Center
Raleigh, NC 27699-1646

Re: Letter Report – Well Abandonment
Community Stop #2
150 West Doctor Martin Luther King Junior Drive
Maxton, North Carolina 28364
Incident Number: 29451
Risk Classification: I170A
CATLIN Project No. 223228.03

Dear Mr. Osman,

CATLIN Engineers and Scientists (CATLIN) is pleased to provide you with this letter
report documenting well abandonment field activities performed in general accordance
with CATLIN proposal number 223228.03P, prepared March 13, 2024. Services were
authorized by the North Carolina Department of Environmental Quality (NCDEQ) Task
Authorization (TA) #03, accepted March 19, 2024, and Contract Number N70522-A. The
approved scope of services for this Task Authorization included:

• Abandon seventeen (17) monitoring wells (MW-1 through MW-16, and TW-1); and
• Prepare a letter report documenting the site activities.

Monitoring Well Abandonment

On April 17, 2024, CATLIN personnel mobilized to the site and abandoned monitoring
wells MW-1 through MW-9, MW-11 through MW-16, and TW-1. CATLIN searched for
monitoring well MW-10 using a ground probe and a metal detector; however, this well
could not be located. Well construction information for the abandoned wells is provided
in the following table:

May 9, 2023
Page 2 of 3
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

Well ID Well Type Well Depth
(feet)
Well Diameter
(inches)
Abandonment
Procedure
MW-1 Shallow 20.0 2.0 All well materials left in
place
MW-2 Shallow 16.0 2.0 All well materials left in
place
MW-3 Shallow 16.0 2.0 All well materials left in
place
MW-4 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-5 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-6 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-7 Shallow 15.0 2.0 All well materials left in
place
MW-8 Shallow 15.0 2.0 All well materials left in
place
MW-9 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-11 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-12 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-13 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-14 Shallow 15.0 2.0 Concrete and well
shield removed.
MW-15 Shallow 15.0 2.0 All well materials left in
place
MW-16 Shallow 22.0 2.0 All well materials left in
place
TW-1 Deep 50.0 2.0 All well materials left in
place

Monitoring wells MW-1 through MW-9, MW-11 though MW-16, and TW-1 were
abandoned by a North Carolina Certified Well Contractor (CWC) according to guidance
provided in the North Carolina Administrative Code (NCAC) Title 15A 02C .0113
(Abandonment of Wells). All well materials were abandoned in place and packed with
bentonite chips to within six inches of the surface while simultaneously pouring water to
facilitate hydration. The remaining space was filled with concrete (MW-1, MW-2, MW-3
MW-7, MW-8, MW-15, MW-16 and TW-1) or topsoil (MW-4, MW-5, MW-6, MW-9,
MW-11, MW-12, MW-13, and MW-14) to the existing grade.

May 9, 2023
Page 3 of 3
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024
The site vicinity and well locations are shown on Figures 1 and 2, respectively
(Attachment A). The well abandonment records were previously submitted to the NCDEQ
Division of Water Quality under separate cover, and a copy is provided in Attachment B.
Photographs of the abandoned wells are included in Attachment C.

CATLIN Engineers and Scientists appreciates this opportunity to be of service. Should
you have any questions or require additional information, please contact us at (919) 838-
2875.

Sincerely,

Sean J. O’Neil, PE
Project Manager

Attachments:
A: Figures
B: Well Abandonment Records
C: Site Photographs

FA-3270_29451_CA_LTRRPT_20240509_Well Abandonment

NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

ATTACHMENT A

FIGURES

FLORENCE ST
W MARTIN LUTHER KING JR DR
SITE LOCATION
Copyright:© 2013 National Geographic Society, i-cubed
2,000 0 2,000 4,0001,000
Feet
³
FIGUREPROJECTTITLE
1
COMMUNITY STOP #2
150 W MARTIN LUTHER KING JR DR
MAXTON, NC
SITE VICINITY MAP
INCIDENT NO.JOB NO.DATE SCALE DRAWN BY/CHECKED BY29451223228MAY 2024 AS SHOWN KMC/SJO
!(
!(
!(
!>!(>
!>
!>
!>
!>
!>!>
!>
!>
!>
!>
!>
!>
!>
!>
!>
FLO
R
E
N
C
E

S
T
W MARTIN

L
U
T
H
E
R

K
I
N
G

J
R

D
R
CURRENT DISPENSERS
FORMERDISPENSERS
12,000-GAL.GASOLINE USTS10,000-GAL.GASOLINE UST10,000-GAL.DIESEL UST 10,000-GAL.KEROSENE UST
MW-6
MW-7
MW-9
MW-8
MW-5
MW-4
MW-3
MW-2
TW-1MW-1
MW-15
MW-10(CNL)
MW-14
MW-13
MW-12
MW-11
MW-16
Source: Esri, Maxar, Earthstar Geographics, and the GIS User Community
60
³
FIGUREPROJECTTITLE
2
INCIDENT NO.JOB NO.DATE SCALE DRAWN BY/CHECKED BY
!>
!(>
LEGEND
!>

NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

ATTACHMENT B

WELL ABANDONMENT RECORDS

WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
35 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-1
20
8.25
5.84
Unknown
5
15
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
30 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-2
16
8.25
4.99
Unknown
6
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
30 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-3
15
8.25
6.04
Unknown
6
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Well was abandoned using hydrated bentonite to
approximately 6 inches below land surface.
Concrete and well shield removed and topsoil used
to bring opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-4
15
8.25
4.89
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Well was abandoned using hydrated bentonite to
~6 inches below land surface. Concrete and well
shield removed. Topsoil used to bring opening to
grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-5
15
8.25
5.34
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to
approximately 6 inches below land surface. Topsoil
used to bring opening to grade after removal of the
concrete and well shield.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-6
15
8.25
4.88
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and the remaining opening brought to
grade using topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-7
15
8.25
4.95
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6 inches
Below land surface. Concrete and well shield removed
and filled the remaining opening to grade using
topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-8
15
8.25
4.84
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and then remaining opening brought to
grade using topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-9
15
8.25
7.53
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and the remaining opening was brought
to grade using topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-11
15
8.25
5.31
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and then opening was brought to grade
using topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-12
15
8.25
4.98
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and the remaining opening brought to
grade using topsoilNic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-13
15
8.25
6.12
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Soil
25 lbs
25 lbs
4/17/2024
Abandoned well using hydrated bentonite to ~6
inches below land surface. Concrete and well shield
removed and the remaining opening brought to
grade using topsoil.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-14
15
8.25
7.04
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
25 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-15
15
8.25
6.05
Unknown
5
10
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
25 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
MW-16
22
8.25
5.56
Unknown
2
20
WELL ABANDONMENT RECORD
Form GW-30 North Carolina Department of Environmental Quality - Division of Water Resources Revised 2-22-2016
1. Well Contractor Information:
Well Contractor Name (or well owner personally abandoning well on his/her property)
NC Well Contractor Certification Number
Company Name
2. Well Construction Permit #:
List all applicable well construction permits (i.e. UIC, County, State, Variance, etc.) if known
3. Well use (check well use):
Water Supply Well:
□Agricultural □Municipal/Public
□Geothermal (Heating/Cooling Supply)□Residential Water Supply (single)
□Industrial/Commercial □Residential Water Supply (shared)
□Irrigation
Non-Water Supply Well:
□Monitoring □Recovery
Injection Well:
□Aquifer Recharge □Groundwater Remediation
□Aquifer Storage and Recovery □Salinity Barrier
□Aquifer Test □Stormwater Drainage
□Experimental Technology □Subsidence Control
□Geothermal (Closed Loop)□Tracer
□Geothermal (Heating/Cooling Return) □Other (explain under 7g)
4. Date well(s) abandoned:
5a. Well location:
Facility/Owner Name Facility ID# (if applicable)
Physical Address, City, and Zip
County Parcel Identification No. (PIN)
5b. Latitude and longitude in degrees/minutes/seconds or decimal degrees:
(if well field, one lat/long is sufficient)
N W
CONSTRUCTION DETAILS OF WELL(S) BEING ABANDONED
Attach well construction record(s) if available. For multiple injection or non-water supply wells
ONLY with the same construction/abandonment, you can submit one form.
6a. Well ID#:
6b. Total well depth: (ft.)
6c. Borehole diameter: (in.)
6d. Water level below ground surface: (ft.)
6e. Outer casing length (if known): (ft.)
6f. Inner casing/tubing length (if known): (ft.)
6g. Screen length (if known): (ft.)
WELL ABANDONMENT DETAILS
7a. For Geoprobe/DPT or Closed-Loop Geothermal Wells having the same
well construction/depth, only 1 GW-30 is needed. Indicate TOTAL NUMBER of
wells abandoned:
7b. Approximate volume of water remaining in well(s): (gal.)
FOR WATER SUPPLY WELLS ONLY:
7c. Type of disinfectant used:
7d. Amount of disinfectant used:
7e. Sealing materials used (check all that apply):
□Neat Cement Grout □Bentonite Chips or Pellets
□Sand Cement Grout □Dry Clay
□Concrete Grout □Drill Cuttings
□Specialty Grout □Gravel
□Bentonite Slurry □Other (explain under 7g)
7f. For each material selected above, provide amount of materials used:
7g. Provide a brief description of the abandonment procedure:
8. Certification:
Signature of Certified Well Contractor or Well Owner Date
By signing this form, I hereby certify that the well(s) was (were) abandoned in
accordance with 15A NCAC 02C .0100 or 2C .0200 Well Construction Standards
and that a copy of this record has been provided to the well owner.
9. Site diagram or additional well details:
You may use the back of this page to provide additional well site details or well
abandonment details. You may also attach additional pages if necessary.
SUBMITTAL INSTRUCTIONS
10a. For All Wells: Submit this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Information Processing Unit,
1617 Mail Service Center, Raleigh, NC 27699-1617
10b. For Injection Wells: In addition to sending the form to the address in 10a
above, also submit one copy of this form within 30 days of completion of well
abandonment to the following:
Division of Water Resources, Underground Injection Control Program,
1636 Mail Service Center, Raleigh, NC 27699-1636
10c. For Water Supply & Injection Wells: In addition to sending the form to the
address(es) above, also submit one copy of this form within 30 days of completion
of well abandonment to the county health department of the county where
abandoned.
4/19/2024
Nathaniel Newman
4630C
CATLIN Engineers and Scientists
Bentonite
Concrete
70 lbs
25 lbs
4/17/2024
All well materials abandoned in place using
hydrated bentonite to approximately six inches
below land surface. Concrete was used to bring
remaining opening to grade.Nic's Properties, Inc.00-0-0000018540
150 West Martin Luther King Jr. Drive
Robeson 839549600700
34.736059 -79.350995
TW-1
50
8.25
13.63
Unknown
45
5

NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

ATTACHMENT C

SITE PHOTOGRAPHS

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-1 after abandonment.

View of MW-2 after abandonment.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-2 finished.

View of MW-3 after abandonment.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-3 finished.

View of MW-4 after abandonment.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-4 finished.

View of MW-5 after abandonment.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-5 finished.

View of MW-6 after abandonment.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-6 finished.

View of MW-7 after abandonment.
ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-7 finished.

View of MW-8 finished.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-9 after abandonment.

View of MW-9 finished.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-11 after abandonment.

View of MW-11 finished.
ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-12 after abandonment.

View of MW-12 finished.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-13 after abandonment.

View of MW-13 finished.
ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-14 after abandonment.

View of MW-14 finished.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-15 after abandonment.

View of MW-15 finished.

ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024

View of MW-16 after abandonment.

View of MW-16 finished.
ATTACHMENT C
SITE PHOTOGRAPHS – MARCH 17, 2024
NCDEQ; 29451_Community Stop #2 CATLIN Engineers and Scientists
CATLIN Project No. 223228 May 2024
View of TW-1 after abandonment.

View of TW-1 finished