NC0003468_Other Correspondence_20181015

S V
MC*
�`
thrt DUKE �0! ►�
Dan River Combined Cycle
ENERGY® Duke Energy Carolinas
864 S Edgewood Road
Eden, NC 27288
October 15, 2018
Mr.Jeffrey 0.Poupart
North Carolina Department of Environmental Quality
1617 Mail Service Center
Raleigh. NC 27699-1617
Subject: Duke Energy Carolinas, LLC
Dan River Combined Cycle Station
NPDES Permit: NC0003468
Rockingham County
Dear Mr. Poupart:
On June 18th, 2018, Duke Energy Carolinas, LLC (Duke Energy) provided notification that
discharge of interstitial water was commencing at the subject facility. This notification was
submitted in accordance with the terms of the facility's NPDES permit. Duke Energy hereby
submits notice that a new treatment system is being installed to treat interstitial water for release.
We anticipate that the new system will produce effluent similar to the previous supplemental
treatment system described in the June 18th letter. The new system will also allow for a higher flow
volume to be treated. The new system will be capable of treating 750 gpm (1.08 MGD if used
continuous for a 24 hour day). This flow volume is significantly less than the 1.5 MGD used by the
Division in permitting and Reasonable Potential Analysis calculations.
The purpose of this letter is to provide notification of the planned temporary changes and a
description of this additional treatment process for your information and files. Duke Energy plans
to begin release of this water on November 1, 2018. This letter serves as both our submittal of
plans describing the treatment technologies but also our required notification at least one week
prior to commencement of the discharge found in Section A.(4) on page 8 of 22 of our NPDES
permit.
As you are aware, the historic wastewater treatment system for wastewater flows from Dan River's
former coal generating facility consist of sedimentation and neutralization process provided by
the two site ash basins. That wastewater treatment system will be temporarily supplemented to
include the following additional treatment:
• Reaction tank for chemical addition and equalization (oxidation & pH adjustment)
• RapidsandTM ballasted flocculating clarifier
• Horizontal pressure filter
The treated effluent from the expanded wastewater treatment system will be routed to Dan
River through temporary piping to the permitted outfall 002 location. Any process wastes flows
(such backwash processes) resulting from this additional treatment will be recycled to the ash basin.
Sludge will be collected and properly disposed of in the onsite landfill. The vendor selected to
provide the temporary units will be providing additional operational support staff for the

R
:4 °.1.1t,;
treatment equipment. SDS sheets for chemicals proposed to be used in the process are attached to this
submittal along with a simplified process flow diagram.
In accordance with NCGS 143-215(a6) and because all activity is authorized under the facility's
existing NPDES permit, no authorization to construct is required to be issued before the
temporary systems can be utilized and no NPDES permit modification is necessary.
Duke Energy remains committed to safely closing ash basins at all of our North Carolina sites.
We look forward to continuing to work with your agency i n a collaborative manner to facilitate
this work. If there are any questions, please feel free to contact Joyce Dishmon at
[e-mail] or [phone].`
I certify under penalty of law that this document and all attachments were prepared under my
direction or supervision in accordance with a system designed to assure that qualified personnel
properly gather and evaluate the information submitted. Based on my inquiry of the person or persons
who manage the system. or those persons directly responsible for gathering the information, the
information submitted is, to the best of my knowledge and belief true, accurate, and complete I am
aware that there are significant penalties for submitting false information, including the possibility of
fines and imprisonmentfor knowing violations.
Sincerely,
el /
,7 7p744.
Michael Lanning
GM II-Regulated Stations
Dan River Combined Cycle
Power Generating Carolinas East
Attachments
Cc: Julie Gryzb - w/attachments
NC DWR
1617 Mail Service Center
Raleigh, NC 27699-1617
Sherri Knight- w/attachments
WSRO
450 West Hanes Mill Road
Winston-Salem.NC 27105
Richard Baker-w/attachments-via email
Shannon Langley - w/attachments -via email
Dana Newcomb - w/attachments,ORC
Joyce Dishmon/Filenet- w/attachments

Duke Energy Carolinas, LLC NPDES Permit NC0003468
Dan River Combined Cycle Station Interstitial Water Treatment Flow Chart
Mobile
SECONDARY Interstitial Water
— Reaction/Feed
BASIN
tank
0
-0
opt�o�a� Undertow--- Ballasted
PRIMARY }nterst�t�a}Water
Blo�,down Flocculating
Clarifier
BASIN
eac
kH'ash
Pressure Filter
Outfall 002 to Dan River

4 �
•
ATS
Y ,:..
ALPINE TECHNICAL SERVICES
Yk,PSk':':iY
Material Safety Data Sheet
ATS-AE-150
1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY
Product name. ATS-AE-150
Company: Alpine Technical Services
601 Nest 6825 South
Midvale. UT 84047
Telephone: [phone]
Telefax: 801-255-0486
Emergency telephone number. Chem-1 el 800-255-3924
Product Use Processing aid for industrial applications
2 HAZARDS IDENTIFICATION
Appearance and Odor
I orm: Viscous liquid
Color: Milky
Odor: Aliphatic
Emeraencv Overview.
Spills produce extremely slippery surfaces
3 COMPOSITIONIINFORMATION ON INGREDIENTS
Identification Anionic water-soluble polymer in emulsion
4 FIRST AID MEASURES
Inhalation:No hazards which require special first aid measures.
Skin contact: Nash off immediately with soap and plenty of water. In case of persistent skin irritation,consult a physician
Eye contact- Rinse thoroughly with plenty of water. also under the eyelids. In case of persistent eye irritation.consult a physician
Ingestion. The product is not considered toxic based on studies on laboratory animals.
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

•
a
6
sEivi
5 FIRE-FIGHTING MEASURES
Suitable extinguishing media. Water Water spray Foam.Carbon dioxide(CO2). Dry powder.
Precautions: Spills produce extremely slippery surfaces.
Special protective equipment for firelighters: No special protective equipment required
Flash point• Does not flash.
Autoignition temperature: Does not ignite
6.ACCIDENTAL RELEASE MEASURES
Personal precautions. No special precautions required.
knvnonmental precautions: Do not contaminate water.
Methods for cleaning up • Do not Ilush with water Dam up Soak up with inert absorbent material. IF liquid has been spilt in laige
quantities clean up promptly by scoop or ti acuum. Keep in suitable and closed containers for disposal After cleaning.flush away traces
with water.
7.HANDLING AND STORAGE
I kindling
Safe handling advice: Avoid contact with skin and eyes. When prepanng the woiking solution ensuie there is adequate
ventilation When using do not smoke.
Storage
Keep in a dry cool place(0-30°C). Freciing will affect the physical condition and may damage the material
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
I:ngincering measures
Use local exhaust if misting occurs.Natural ventilation is adequate in absence of mists.
Personal protective equipment:
Respiratory protection: In case of insufficient ventilation wear suitable respiratory equipment.
I land protection. Rubber gloves.
Eye protection: Safety glasses with side-shields. Do not wear contact lenses where this product is used.
Skin and body protection. Chemical resistant apron or protective suit if splashing or repeated contact with solution is
likely.
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

ATS
ALPINE
Hygiene measures
Wash hands and face before breaks and immediately after handling the product Handle in accordance with good industrial
hygiene and safety pi actice
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

NIC SERVICES
v
9.PHYSICAL AND CHEMICAL PROPERTIES
Poria Viscous liquid
Color. Milky
Odor. Aliphatic
p11 : 6- 8@5c/I
Melting point/range Not applicable
Flash point: Does not flash
Autoignition tempeiature Does not ignite
Appiox bulk density• 1.05
Wates solubility: Sec"Technical Bulletin
I 0 STABILITY AND REACTIVITY
Stability: Stable l laiaidons polymerisation docs not occur.
Materials to avoid. Oxidizing agents may cause exothermic reactions.
11a/ill-thus decomposition products. [hernial decomposition may produce Carbon oxides(COx). Nitrogen oxides(NOx)
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

•
ATS
ALPINE TECHNICAL SERVICES
11 TOXICOLOGICAL INFORMATION
Acute toxicit),
Skin: The product is not expected to he toxic.
Oral: LD50/oral/rat>5000 mg/kg.
Inhalation. The product is not expected to be toxic by inhalation.
Irritation
Skin. May cause skin irritation with susceptible persons
Eyes: May cause eye in itation with susceptible pet sons
Sensitization- The product is not expected to be
sensitizing.
Chronic toxicity: Prolonged skin contact may deiat the skin and produce dermatitis.
12 ECOLOGICAL INFORMATION
Aquatic toxicity
1oxicity to fish: LC50/96 hours> 100 mg/I (OECD 203).Toxicity
to daphnia. EC50/48 hours> 100 mg/1(OECD 202).
Toxicity to algae 1C50/Scenedesmus subspicatus/72 hours> 100 mpg/I (OECD 201)
Environmental fate
Persistence and degradability : Not readily biodegradable
Hydrolysis- Does not hydrolyse.
13 DISPOSAL CONSIDERATIONS
Disposal: In accordance with local, state and federal regulations.
Container Rinse empty containers with water and use the rinse water to prepare the working solution.Can he landfilled or
incineiated. when in compliance with local, state and federal regulations.
14 TRANSPORT INFORMATION
DOT
Dot status: Not classified as dangerous in the meaning of DOT regulations
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

KIS
1MDG/l MO
Remarks:Not classrlied as dangerous in the meaning of IMO/1MDG regulations.
ICAO/IATA
Remarks. Not classified as dangerous in the meaning of1CAO/IATA regulations
15 REGULATORY INFORMATION
International Inventor res
Futopean Union(EINECS/ELINCS) : All components of this product arc eithei listed on the inventory or are exempt from
listing
USA('TSCA) : All components of this product are eithei listed on the inventory or arc exempt from listing.
Canada(DSL) . All components of this product are either listed on the inventory or are exempt from listing.
Austialia(AICS) : All components of this product are either listed on the inventory or are exempt from listing.
China(IECSC) :All components of this product arc either listed on the inventory or arc exempt from listing
Japan (ENCS) All components of this product are either li-zfe�d on the inventory or are exempt from listing
Korea(ECL) : All components of this product are either listed on the inventory or are exempt Irum listing
Philippines(PICCS) • All components of this product are either listed on the inventory or are exempt from listing
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

-- - - - - - - - --- - - - - - - - - ---- -- -- - - -
ATS
Pftisio ALPINE TECHNICAL SERVICES
0040.0
16.OTHER INFORMATION
NEPA and HMIS Ratints.
NFPA
I-lealth : 1
1'Ianimabil,t .
Instabillt\ • 0
HMIS:
I lealth • I
Flat nabilit\ • I
Ph\sical I lazard. 0
I lie dat t in this\fatenal Data Sheet relates onl} to the speulic matzo tl desr_nated heten,and doe,not',late to use III Combination iS rth an:,other mate:.tl ut in art.ptoses, "I ht,information is
based upon technical mlbnnattoa belies ed to he reliable It"subject to tes"ron a,additional Icnov.I dge and.spertenee is seamed "Ilii,mtotmattonba-ed up, t technical information belies ed
to be It is subject to tr„,con as additional l.nms ledge and e\penence t,cam:d
Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047
April 18,2011

Alpine Technical Services, 601 West 6825 South, Midvale, Utah 84047-1047

Product#: 138874 From. BRENNTAG MID-SOUTH INC. To: Thursday,October 11,2018
BRENNTAGMM-: SAFETY DATA SHEET
1. Identification
Product identifier BRENNFLOC CP 98116
Other means of identification None
Recommended use ALL PROPER AND LEGAL PURPOSES
Recommended restrictions None known
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name Brenntag Mid-South, Inc
Address 1405 Highway 136,West
Henderson, KY 42420
Telephone [phone]
E-mail Not available.
Emergency phone number 800-424-9300 CHEMTREC
2. Hazard(s) identification
Physical hazards Not classified.
Health hazards Sensitization,skin Category 1
Germ cell mutagenicity Category 1
Carcinogenicity Category 1
Reproductive toxicity Category 1
Aspiration hazard Category 1
Environmental hazards Not classified
OSHA defined hazards Not classified.
Label elements
Signal word Danger
Hazard statement May be fatal if swallowed and enters airways. May cause an allergic skin reaction May cause
genetic defects May cause cancer. May damage fertility or the unborn child
Precautionary statement
Prevention Obtain special instructions before use Do not handle until all safety precautions have been read
and understood,Avoid breathing mist or vapor Contaminated work clothing must not be allowed
out of the workplace Wear protective gloves/protective clothing/eye protection/face protection.
Response If swallowed. Immediately call a poison center/doctor Do NOT induce vomiting If on skin. Wash
with plenty of water If exposed or concerned. Get medical advice/attention If skin irritation or rash
occurs' Get medical advice/attention Wash contaminated clothing before reuse
Storage Store locked up
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations
Hazard(s)not otherwise Combustible
classified (HNOC)
Supplemental information 64 8%of the mixture consists of component(s)of unknown acute oral toxicity 64 8%of the
mixture consists of component(s)of unknown acute dermal toxicity, 99.9%of the mixture consists
of component(s)of unknown acute inhalation toxicity.
3. Composition/information on ingredients
Mixtures
Chemical name Common name and synonyms CAS number
TRADE SECRET' Proprietary* 25
Material name BRENNFLOC CP 98116 sos us
138874 Version#.02 Revision date'10-11-2018 Issue date-02-22-2018 1 /8

'roduct#: 138874 From BRENNTAG MID-SOUTH INC. To. Thursday, October 11, 2018
Chemical name Common name and synonyms CAS number %
TRADE SECRET' Proprietary* 0 1
Other components below reportable levels 74 9
'Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret
4. First-aid measures
Inhalation Move to fresh air Call a physician if symptoms develop or persist
Skin contact Remove contaminated clothing immediately and wash skin with soap and water In case of
eczema or other skin disorders Seek medical attention and take along these instructions
Eye contact Rinse with water. Get medical attention if irritation develops and persists.
Ingestion Call a physician or poison control center immediately Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Most important Aspiration may cause pulmonary edema and pneumonitis May cause an allergic skin reaction
symptoms/effects,acute and Dermatitis Rash
delayed
Indication of immediate Provide general supportive measures and treat symptomatically. Keep victim under observation
medical attention and special Symptoms may be delayed
treatment needed
General information IF exposed or concerned. Get medical advice/attention If you feel unwell, seek medical advice
(show the label where possible). Ensure that medical personnel are aware of the material(s)
involved, and take precautions to protect themselves Show this safety data sheet to the doctor in
attendance.Wash contaminated clothing before reuse.
5. Fire-fighting measures
Suitable extinguishing media Alcohol resistant foam. Powder. Dry chemicals. Carbon dioxide (CO2)
Unsuitable extinguishing Do not use water jet as an extinguisher,as this will spread the fire.
media
Specific hazards arising from During fire, gases hazardous to health may be formed.
the chemical
Special protective equipment Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
and precautions for firefighters
Fire fighting Cool containers exposed to heat with water spray and remove container, if no risk is involved
equipment/instructions
Specific methods Use standard firefighting procedures and consider the hazards of other involved materials.
General fire hazards Combustible No unusual fire or explosion hazards noted
6. Accidental release measures
Personal precautions, Keep unnecessary personnel away. Keep people away from and upwind of spill/leak Wear
protective equipment and appropriate protective equipment and clothing during clean-up Avoid breathing mist or vapor. Do
emergency procedures not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ensure adequate ventilation Local authorities should be advised if significant spillages cannot be
contained For personal protection, see section 8 of the SDS
Methods and materials for Use water spray to reduce vapors or divert vapor cloud drift. Prevent entry into waterways,sewer,
containment and cleaning up basements or confined areas
Large Spills Stop the flow of material, if this is without risk. Dike the spilled material,where this is
possible Absorb in vermiculite, dry sand or earth and place into containers. Following product
recovery, flush area with water
Small Spills:Wipe up with absorbent material(e.g cloth, fleece) Clean surface thoroughly to
remove residual contamination.
Never return spills to original containers for re-use. Put material in suitable,covered, labeled
containers. For waste disposal, see section 13 of the SDS. For waste disposal, see section 13 of
the SDS
Environmental precautions Avoid discharge into drains,water courses or onto the ground
Material name BRENNFLOC CP 98116 sos us
138874 Version#:02 Revision date 10-11-2018 Issue date:02-22-2018 2/8

•
Product#: 138874 From: BRENNTAG MED-SOUTH INC To• Thursday, October 11,2018
•
7. Handling and storage
Precautions for safe handling Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood.Avoid breathing mist or vapor.Avoid contact with eyes, skin, and clothing Avoid
prolonged or repeated contact with skin Avoid prolonged exposure Pregnant or breastfeeding
women must not handle this product Should be handled in closed systems,if possible. Use only in
well-ventilated areas Wear appropriate personal protective equipment Wash hands thoroughly
after handling. Observe good industrial hygiene practices
Conditions for safe storage, Store locked up Keep away from heat and sources of ignition. Store in original tightly closed
including any incompatibilities container Store away from incompatible materials(see Section 10 of the SDS). Store away from
incompatible materials(see Section 10 of the SDS)
8. Exposure controls/personal protection
Occupational exposure limits
US.OSHA Table Z-1 Limits for Air Contaminants(29 CFR 1910.1000)
Components Type Value
TRADE SECRET PEL 0.3 mg/m3
US.ACGIH Threshold Limit Values
Components Type Value Form
TRADE SECRET TWA 0.03 mg/m3 Inhalable fraction and
vapor.
US.NIOSH: Pocket Guide to Chemical Hazards
Components Type Value
TRADE SECRET TWA 0.03 mg/m3
Biological limit values No biological exposure limits noted for the ingredient(s)
Exposure guidelines
US-California OELs: Skin designation
TRADE SECRET(CAS Proprietary) Can be absorbed through the skin
US-Minnesota Haz Subs:Skin designation applies
TRADE SECRET(CAS Proprietary) Skin designation applies
US-Tennessee OELs:Skin designation
TRADE SECRET(CAS Proprietary) Can be absorbed through the skin.
US ACGIH Threshold Limit Values:Skin designation
TRADE SECRET(CAS Proprietary) Can be absorbed through the skin
US NIOSH Pocket Guide to Chemical Hazards: Skin designation
TRADE SECRET(CAS Proprietary) Can be absorbed through the skin
US.OSHA Table Z-1 Limits for Air Contaminants(29 CFR 1910.1000)
TRADE SECRET(CAS Proprietary) Can be absorbed through the skin
Appropriate engineering Good general ventilation(typically 10 air changes per hour)should be used.Ventilation rates
controls should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits If
exposure limits have not been established,maintain airborne levels to an acceptable level
Individual protection measures,such as personal protective equipment
The following are recommendations for Personnel Protective Equipment(PPE).The employer/user of this product must perform a
Hazard Assessment of the workplace according to OSHA regulations 29 CFR 1910 132 to determine the appropriate PPE for use
while performing any task involving potential exposure to this product
Eye/face protection Chemical respirator with organic vapor cartridge and full facepiece
Skin protection
Hand protection Wear appropriate chemical resistant gloves Suitable gloves can be recommended by the glove
supplier.
Other Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.
Respiratory protection Chemical respirator with organic vapor cartridge and full facepiece.
Thermal hazards Wear appropriate thermal protective clothing,when necessary.
General hygiene Observe any medical surveillance requirements Always observe good personal hygiene
considerations measures,such as washing after handling the material and before eating, drinking,and/or
smoking Routinely wash work clothing and protective equipment to remove contaminants.
Contaminated work clothing should not be allowed out of the workplace
Material name BRENNFLOC CP 98116 sos us
138874 Version#:02 Revision date:10-11-2018 Issue date.02-22-2018 3/8

'roduct#• 138874 From. BRENNTAG MID-SOUTH INC To Thursday,October 11,2018
9. Physical and chemical properties
Appearance
Physical state Liquid.
Form Liquid.
Color MILKY
Odor ALIPHATIC
Odor threshold Not available
pH Not available
Melting point/freezing point 41 °F (5 °C)
Initial boiling point and boiling 212 47°F (100 26°C)estimated
range
Flash point Not available
Evaporation rate Not available
Flammability(solid,gas) Not applicable.
Upper/lower flammability or explosive limits
Flammability limit-lower Not available
(%)
Flammability limit-upper Not available
(%)
Explosive limit-lower(%) Not available
Explosive limit-upper(%) Not available.
Vapor pressure Not available.
Vapor density Not available.
Relative density Not available.
Solubility(ies)
Solubility(water) Not available
Partition coefficient Not available
(n-octanol/water)
Auto-ignition temperature Not available
Decomposition temperature Not available.
Viscosity Not available
Other information
Density 8 18 lbs/gal
Explosive properties Not explosive
Oxidizing properties Not oxidizing
Percent volatile 35 1 %estimated
Specific gravity 0.98
VOC 0 05 %estimated
10. Stability and reactivity
Reactivity The product is stable and non-reactive under normal conditions of use,storage and transport.
Chemical stability Material is stable under normal conditions
Possibility of hazardous No dangerous reaction known under conditions of normal use.
reactions
Conditions to avoid Contact with incompatible materials
Incompatible materials Strong oxidizing agents
Hazardous decomposition Toxic gas.
products
11. Toxicological information
Information on likely routes of exposure
Inhalation Prolonged inhalation may be harmful.
Material name BRENNFLOC CP 98116 sos us
138874 Version#.02 Revision date-10-11-2018 Issue date_02-22-2018 4/8

Product#. 138874 From: BRENNTAG MID-SOUTH INC To. Thursday, October 11,2018
Skin contact May cause an allergic skin reaction.
Eye contact Direct contact with eyes may cause temporary irritation.
Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious
chemical pneumonia
Symptoms related to the Aspiration may cause pulmonary edema and pneumonitis May cause an allergic skin reaction
physical,chemical and Dermatitis. Rash.
toxicological characteristics
Information on toxicological effects
Acute toxicity May be fatal if swallowed and enters airways.
Skin corrosion/irritation Prolonged skin contact may cause temporary irritation
Serious eye damage/eye Direct contact with eyes may cause temporary irritation
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
Skin sensitization May cause an allergic skin reaction
Germ cell mutagenicity May cause genetic defects
Carcinogenicity May cause cancer.
IARC Monographs.Overall Evaluation of Carcinogenicity
TRADE SECRET(CAS Proprietary) 2A Probably carcinogenic to humans
OSHA Specifically Regulated Substances(29 CFR 1910.1001-1052)
Not regulated,
US.National Toxicology Program(NTP) Report on Carcinogens
TRADE SECRET(CAS Proprietary) Reasonably Anticipated to be a Human Carcinogen.
Reproductive toxicity May damage fertility or the unborn child
Specific target organ toxicity- Not classified
single exposure
Specific target organ toxicity- Not classified.
repeated exposure
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged inhalation may be harmful.
12. Ecological information
Ecotoxicity The product is not classified as environmentally hazardous However,this does not exclude the
possibility that large or frequent spills can have a harmful or damaging effect on the environment.
Components Species Test Results
TRADE SECRET
Aquatic
Fish LC50 Fathead minnow(Pimephales promelas) 77-160 mg/I,96 hours
Rainbow trout,donaldson trout 2.9 mg/I,96 hours
(Oncorhynchus mykiss)
Persistence and degradability No data is available on the degradability of any ingredients in the mixture.
Bioaccumulative potential
Partition coefficient n-octanol/water(log Kow)
TRADE SECRET -0.67
Mobility in soil No data available.
Other adverse effects No other adverse environmental effects(e.g.ozone depletion, photochemical ozone creation
potential,endocrine disruption, global warming potential) are expected from this component
13. Disposal considerations
Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of
contents/container in accordance with local/regional/national/international regulations
Local disposal regulations Dispose in accordance with all applicable regulations
Hazardous waste code The waste code should be assigned in discussion between the user,the producer and the waste
disposal company.
Material name.BRENNFLOC CP 98116 sos us
138874 Version#:02 Revision date.10-11-2018 Issue date.02-22-2018 5/8

rocluct#. 138874 From. BRENNTAG MTD-SOUTH INC. To: Thursday,October 11,2018
•
Waste from residues/unused Dispose of in accordance with local regulations Empty containers or liners may retain some
products product residues This material and its container must be disposed of in a safe manner(see
Disposal instructions).
Contaminated packaging Since emptied containers may retain product residue, follow label warnings even after container is
emptied Empty containers should be taken to an approved waste handling site for recycling or
disposal
14. Transport information
DOT
Not regulated as dangerous goods.
Transport information on packaging may be different from that listed Transportation information on packaging may be different
from that listed.
IATA
Not regulated as dangerous goods.
IMDG
UN number UN3082
UN proper shipping name ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N 0 S (TRADE SECRET), MARINE
POLLUTANT
Transport hazard class(es)
Class 9
Subsidiary risk -
Packing group II I
Environmental hazards
Marine pollutant Yes
EmS F-A, S-F
Special precautions for user Read safety instructions, SDS and emergency procedures before handling
IMDG
\ ,i
Marine pollutant
General information IMDG Regulated Marine Pollutant
15. Regulatory information
US federal regulations This product is a"Hazardous Chemical"as defined by the OSHA Hazard Communication
Standard,29 CFR 1910.1200.
TSCA Section 12(b) Export Notification(40 CFR 707, Subpt.D)
Not regulated
CERCLA Hazardous Substance List(40 CFR 302.4)
TRADE SECRET(CAS Proprietary) Listed
SARA 304 Emergency release notification
TRADE SECRET(CAS Proprietary) 5000 LBS
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
Material name BRENNFLOC CP 98116 sos us
138874 Version#-02 Revision date.10-11-2018 Issue date:02-22-2018 6/8

- - - - - - - - - - - - -- - - - - - - -- - - - - -
Product# 138874 From BRENNTAG MID-SOUTH INC. To• Thursday, October 11,2018
Superfund Amendments and Reauthorization Act of 1986 (SARA)
SARA 302 Extremely hazardous substance
Chemical name CAS number Reportable Threshold Threshold Threshold
quantity planning quantity planning quantity, planning quantity,
(pounds) (pounds) lower value upper value
(pounds) (pounds)
TRADE SECRET Proprietary 5000 1000 10000
SARA 311/312 Hazardous Yes
chemical
Classified hazard Respiratory or skin sensitization
categories Germ cell mutagenicity
Carcinogenicity
Reproductive toxicity
Aspiration hazard
SARA 313 (TRI reporting)
Chemical name CAS number % by wt.
TRADE SECRET Proprietary 0 1
Other federal regulations
Clean Air Act(CAA)Section 112 Hazardous Air Pollutants(HAPs) List
TRADE SECRET(CAS Proprietary)
Clean Air Act(CAA)Section 112(r)Accidental Release Prevention (40 CFR 68.130)
Not regulated
Safe Drinking Water Act Not regulated
(SDWA)
US state regulations
California Proposition 65
A WARNING: This product can expose you to TRADE SECRET,which is known to the State of California to
cause cancer and birth defects or other reproductive harm. For more information go
to www.P65Warnings ca gov
California Proposition 65 -CRT: Listed date/Carcinogenic substance
TRADE SECRET(CAS Proprietary) Listed. January 1, 1990
California Proposition 65 -CRT: Listed date/Developmental toxin
TRADE SECRET(CAS Proprietary) Listed February 25 2011
California Proposition 65 -CRT: Listed date/Male reproductive toxin
TRADE SECRET(CAS Proprietary) Listed February 25, 2011
US.California.Candidate Chemicals List. Safer Consumer Products Regulations(Cal.Code Regs,tit.22,69502.3,
subd.(a))
TRADE SECRET(CAS Proprietary)
International Inventories
Country(s) or region Inventory name On inventory(yes/no)*
Australia Australian Inventory of Chemical Substances(AICS) Yes
Canada Domestic Substances List(DSL) Yes
Canada Non-Domestic Substances List(NDSL) No
China Inventory of Existing Chemical Substances in China (IECSC) Yes
Europe European Inventory of Existing Commercial Chemical No
Substances(EINECS)
Europe European List of Notified Chemical Substances(ELINCS) No
Japan Inventory of Existing and New Chemical Substances (ENCS) No
Korea Existing Chemicals List(ECL) Yes
New Zealand New Zealand Inventory Yes
Philippines Philippine Inventory of Chemicals and Chemical Substances Yes
(PICCS)
Taiwan Taiwan Toxic Chemical Substances(TCS) Yes
United States& Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
'A"Yes"indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A"No"indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s)
Material name.BRENNFLOC CP 98116 SOS US
138874 Version# 02 Revision date 10-11-2018 Issue date-02-22-2018 7/8

- ------ - -- -----
roduct#. 138874 From BRENNTAG MED-SOUTH INC To. Thursday,October 11, 2018
16. Other information, including date of preparation or last revision
Issue date 02-22-2018
Revision date 10-11-2018
Version# 02
H MIS®ratings Health.3*
Flammability 0
Physical hazard. 0
NFPA ratings Health.0
Flammability' 0
Instability.0
Disclaimer While Brenntag believes the information contained herein to be accurate, Brenntag makes no
representation or warranty,express or implied, regarding, and assumes no liability for,the
accuracy or completeness of the information. The Buyer assumes all responsibility for handling,
using and/or reselling the Product in accordance with applicable federal,state,and local law This
SDS shall not in any way limit or preclude the operation and effect of any of the provisions of
Brenntag's terms and conditions of sale
Revision information This document has undergone significant changes and should be reviewed in its entirety
Material name:BRENNFLOC CP 98116 SOS US
138874 Version#:02 Revision date 10-11-2018 Issue date:02-22-2018 8/8