Loading...
HomeMy WebLinkAboutNC0003425_Draft Permit_20160101 (2)Permit NC0003425 STATE OF NORTH CAROLINA DEPARTMENT OF ENVIRONMENTAL QUALITY DIVISION OF WATER RESOURCES PERMIT TO DISCHARGE WASTEWATER UNDER THE NATIONAL POLLUTANT DISCHARGE ELIMINATION SYSTEM In compliance with the provision of North Carolina General Statute 143-215.1, other lawful standards and regulations promulgated and adopted by the North Carolina Environmental Management Commission, and the Federal Water Pollution Control Act, as amended, Duke Energy Progress, LLC is hereby authorized to discharge wastewater from a facility located at the Roxboro Steam Electric Generating Plant 1700 Dunnaway Road, Semora Person County to receiving waters designated as Hyco Reservoir in the Roanoke River Basin in accordance with effluent limitations, monitoring requirements, and other conditions set forth in Parts I, II, III and IV hereof. This permit shall become effective . This permit and the authorization to discharge shall expire at midnight on. Signed this day . S. Jay Zimmerman, P.G. Division of Water Resources By Authority of the Environmental Management Commission Page 1 of 23 Permit NC0003425 SUPPLEMENT TO PERMIT COVER SHEET All previous NPDES Permits issued to this facility, whether for operation or discharge are hereby revoked. As of this permit issuance, any previously issued permit bearing this number is no longer effective. Therefore, the exclusive authority to operate and discharge from this facility arises under the permit conditions, requirements, terms, and provisions included herein. Duke Energy Progress, LLC is hereby authorized to: Continue to operate the following systems located at Roxboro Steam Electric Generating Plant off NCSR 1377 near Roxboro in Person County: ■ Outfall 001. Continue to discharge stormwater and seeps from the ash landfill and gypsum pile area into Hyco Reservoir. ■ Ash Pond Treatment System (Internal Outfall 002). Continue to discharge ash transport water, low volume wastewater, runoff from the ash landfill, dry fly ash handling system wash water, ash silo wash water, storm water runoff, cooling tower blowdown from unit number 4, emergency overflow of FGD system blowdown, anhydrous ammonia testing waters and emergency flows and domestic sewage treatment plant effluent. Effluent from the ash pond discharges to the heated water discharge canal, and is ultimately released into Hyco Reservoir through Outfall 003. ■ Heated Water Discharge Canal System (Outfall 003). Continue to discharge once -through cooling water, stormwater runoff, flue gas desulfurization treated wastewater, flue gas desulfurization cooling water, seepage from ash pond dam and the effluent from the ash pond (Outfall 002) into Hyco Reservoir. ■ Cooling Tower Blowdown System (Internal Outfall 005). Continue to discharge cooling tower blowdown from unit number 4 into the ash transport system, and ultimately into the ash pond (Outfall 002) or into the discharge canal. ■ Coal Pile Runoff Treatment System (Outfall 006). Continue to discharge runoff from the coal pile and other coal handling areas, including the limestone and gypsum piles and the truck wheel wash water. These waters are routed to a retention pond for treatment by neutralization, sedimentation, and equalization prior to being discharged directly into Hyco Reservoir. ■ Domestic Wastewater Treatment System (Internal Outfall 008). Continue to discharge effluent from the treatment system flows into the ash pond. ■ Chemical Metal Cleaning Treatment System (Internal Outfall 009). Continue to discharge chemical metal cleaning wastes into the ash pond or the low volume waste treatment system. ■ Flue Gas Desulfurization Treatment System (Internal Outfall 010). Continue to operate a FGD wet scrubber treatment system consisting a settling pond and a bioreactor, discharging into the discharge canal. ■ Flue Gas Desulfurization Treatment System (Internal Outfall 011). Upon completion of construction operate a Flue Gas Desulfurization System discharging to the low volume waste treatment system or the discharge canal. ■ Low Volume Wastes Treatment System (Internal Outfall 012). Upon completion of construction of a dual retention ponds treatment system discharge low volume wastes, metal cleaning wastes, dry fly ash handling system wash water, ash silo wash water, emergency overflow of FGD system Page 2 of 23 Permit NC0003425 blowdown, anhydrous ammonia testing waters and emergency flows, domestic sewage treatment plant effluent, and storm water runoff through outfall 012 to the discharge canal. 2. Discharge from said treatment works and/or outfalls at the locations specified on the attached map into the Hyco Reservoir, classified as WS-V 8v B waters in the Roanoke River Basin. Page 3 of 23 Permit NC0003425 Part I A. (1) Effluent Limitations and Monitoring Requirements (Outfall 001) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of this permit and lasting until expiration, the Permittee is authorized to discharge from Outfall 001 (Stormwater and seeps). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample Location Flow, MGD Monthly/Quarterly3 Estimate Effluent H2 Monthly Quarter' 3 Grab Effluent Fluoride, mg/L 1.8 mg/L 1.8 mg/L Monthly/Quarterly3 Grab Effluent Total Arsenic, µg/L 10 µg/L 10 µg/L Monthly/Quarterly3 Grab Effluent Total Copper, µg/L Monthly/Quarterly3 Grab Effluent Total Antimony, µg/1 Monthly/Quarterly3 Grab Effluent Total Lead, µg/L Monthly/Quarterly3 Grab Effluent Total Selenium, µg/L 5 µg/L 56 µg/L Monthly/Quarterly3 Grab Effluent Nitrate as N, mg/L Monthly/ Quarterly3 Grab Effluent Sulfates, mg/L 250 m /L 250 mg/L Monthly/Quarterly3 Grab Effluent TDS, mg/L Monthly/Quarterly3 Grab Effluent Hardness -Total as CaCO3 or (Ca + Mg)] mg/L Monthly/ Quarterly3 Grab Effluent Conductivity, pmho/cm Month/Quarter' 3 Grab Effluent Acute Toxicit 4 Monthly/ Quarter' 3 Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. The pH shall not be less than 6.0 standard units nor greater than 9.0 standard units. 3. The facility shall conduct monthly sampling from the effective date of the permit. After one year from the effective date of the permit the monitoring will be reduced to quarterly 4. Acute Toxicity (Pimephales promelas, 24-hour) monitoring shall be performed in accordance with Special Condition A. (14) of this permit. If the facility is unable to obtain a sample due to the dry or low flow conditions preventing the facility from obtaining a representative sample, then "no flow" should be reported on the DMR. This requirement is established in the Section D of the Standard Conditions and 40 CFR 122.416). There shall be no discharge of floating solids or visible foam in other than trace amounts. Page 4 of 23 Permit NC0003425 A. (2) Effluent Limitations and Monitoring Requirements (Outfall 002 - normal operation - decanting phase) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 002 (Ash Pond Treatment System to the Heated Water Discharge Canal - Decanting of the free water above the settled ash layer that does not involve mechanical disturbance of the ash). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS I MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample Location2 Flow Daily Continuous Effluent Total Selenium Monthly Grab Effluent Oil and Grease 15.0 m L 20.0 m L 2/Month Grab Effluent Total Suspended Solids3 30.0 m L 100 m L 2/Month Grab Effluent Turbidity4, NTU Monthly Grab Effluent pH5 Between 6.0 and 9.0 Standard Units Monthly Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Samples taken in compliance with the monitoring requirements listed above shall be taken at the ash pond discharge prior to mixing with other sources of wastewater. 3. The facility shall continuously monitor TSS concentration when the decanting process commences and the dewatering pump shall be shutoff automatically when the one half of the Daily Maximum limit (15 minutes average) is exceeded. Pumping will be allowed to continue if interruption might result in a dam failure or damage. The continuous TSS monitoring only required when the pumps are employed for decanting. 4. The net turbidity shall not exceed 50 NTU using a grab sample and measured by the difference between the effluent turbidity and the background turbidity. The sample for the background turbidity shall be taken at point in the receiving waterbody upstream of the discharge location, and the background turbidity and the effluent turbidity samples shall be taken within the same 24 hour period. NTU - Nephelometric Turbidity Unit. 5. The facility shall continuously monitor pH when the decanting process commences and the decanting pump shall be shutoff automatically when 15 minutes running average pH falls below 6.1 standard unis or rises above 8.9 standard units. Pumping will be allowed to continue if interruption might result in a dam failure or damage. The low volume waste shall be discharged to the ash pond treatment system until new treatment system is in operation. By November 1, 2018 there shall be no discharge of pollutants in fly ash transport waters. This requirement only applies to fly ash ash transport water generated after November 1, 2018. By April 30, 2021 there shall be no discharge of pollutants in bottom ash transport waters. This requirement only applies to bottom ash transport water generated after November 1, 2018. The facility is allowed to drawdown the wastewater in the ash pond to no less than three feet above the ash. The level of water in the ash pond should not be lowered more than 1 ft/week, unless approved by the DEQ Dam Safety Program. Page 5 of 23 Permit NC0003425 The facility shall use a floating pump station with free water skimmed from the basin surface using an adjustable weir. The limits and conditions in Section A. (3) of the permit apply when water in the ash settling basin is lowered below the three feet trigger mark. The facility shall notify DWR Complex NPDES Permitting Unit and DWR Raleigh Regional Office seven calendar days prior to the commencement of the decanting. Page 6 of 23 Permit NC0003425 A. (3) Effluent Limitations and Monitoring Requirements (Outfall 002 - dewatering phase) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 002 (Ash Pond Treatment System Dewatering - removing the interstitial water). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample Location2 Flow 1 MGD Weekly Continuous Effluent Total Selenium Weekly Grab Effluent Total Arsenic Weekly Grab Effluent Total Mercury Weekly Grab Effluent Total Molybdenum Weekly Grab Effluent Total Antimony Weekly Grab Effluent Total Copper Weekly Grab Effluent Oil and Grease 15.0 m L 20.0 m L Weekly Grab Effluent Total Suspended Solids 30.0 m L 100 m L Weekly Grab Effluent Turbidity3, NTU Monthly Grab Effluent pH4 Between 6.0 and 9.0 Standard Units Monthly Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Effluent sampling shall be conducted at the discharge from the ash settling pond prior to mixing with any other waste stream. 3. The net turbidity shall not exceed 50 NTU using a grab sample and measured by the difference between the effluent turbidity and the background turbidity. The sample for the background turbidity shall be taken at point in the receiving waterbody upstream of the discharge location, and the background turbidity and the effluent turbidity samples shall be taken within the same 24 hour period. NTU - Nephelometric Turbidity Unit. 4. The facility shall continuously monitor pH when the decanting process commences and the decanting pump shall be shutoff automatically when 15 minutes running average pH falls below 6.1 standard unis or rises above 8.9 standard units. Pumping will be allowed to continue if interruption might result in a dam failure or damage. There shall be no discharge of floating solids or visible foam in other than trace amounts. By November 1, 2018 there shall be no discharge of pollutants in fly ash transport waters. This requirement only applies to fly ash transport water generated after November 1, 2018. By April 30, 2021 there shall be no discharge of pollutants in bottom ash transport waters. This requirement only applies to fly ash transport water generated after November 1, 2018. The level of water in the ash pond should not be lowered more than 1 ft/week, unless approved by the DEQ Dam Safety Program. The facility shall use a floating pump station with free water skimmed from the basin surface using an adjustable weir. Page 7 of 23 Permit NC0003425 A. (4) Effluent Limitations and Monitoring Requirements (Outfall 003) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Outfall 003 (Heated Water Discharge Canal System to the Hyco Reservoir). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample a Sample Locationz Flow Daily Calculation Effluent Total Residual Chlorine3 28 µg/L 2/Month Grab Effluent Total Phosphorus Monthly Grab Effluent Total Nitrogen Monthly Grab Effluent Temperature 4 Continuous Recorder Effluent, 4C4, 4D4 Total Arsenic Quarterly Grab Effluent Total Selenium Quarterly Grab Effluent Chloride Quarterly Grab Effluent Total Thallium Quarterly Grab Effluent H5 Weekly Grab Effluent Ammonia6 1.0 mg/1 5 mg/1 Daily Grab Effluent Acute Toxicit 7 Quarterly Composite Effluent Hardness -Total as CaCO3 or Ca + M Quarterly Grab 4C, 4D Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Effluent sampling shall be performed in the discharge canal at the point of discharge into Hyco Reservoir. Stations 4C and 4D are shown on the Hyco Reservoir Sampling Map (attached). 3. Total Residual Chlorine compliance is required only if chlorine or chlorine derivative is added to the cooling water. The Division shall consider all effluent TRC values reported below 50 µg/L to be in compliance with the permit. However, the permittee shall continue to record and submit all values reported by a North Carolina certified laboratory (including field certified), even if these values fall below 50 µg/L. 4. The Permittee shall operate so as to remain in compliance with the conditions outlined in the mixing zone defined in Special Condition A. (17) of this permit. The temperature of Hyco Reservoir at no time shall exceed the thermal water quality standard outside the mixing zone defined in Special Condition A. (17). Continuous monitoring in the mixing zone shall be at a point between Stations 4C and 4D as shown on the Hyco Reservoir Sampling Map (attached). These thermal limitations may be deleted or revised, as appropriate, based upon evaluation of the results of the thermal studies. 5. The pH shall not be less than 6.0 standard units nor greater than 9.0 standard units. 6. Ammonia limit and monitoring is only applicable in the event of an emergency release of anhydrous ammonia during the time the released waters are discharged through outfall 003. 7. Acute Toxicity (Pimephales promelas) P/F @ 90%, March, June, September and December. See Special Condition A. (14) of this permit. Composite samples for this effluent characteristic shall consist of 24 or more grab samples of equal volumes collected at equal intervals over a 24-hour period. The Permittee is allowed to operate Unit 3 in a once -through cooling mode from October 15 through April 30. Page 8 of 23 Permit NC0003425 There shall be no discharge of floating solids or visible foam in other than trace amounts outside a distance five (5) meters from the discharge pipe. A. (5) Effluent Limitations and Monitoring Requirements (Internal Outfall 005) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 005 (Cooling Tower Blowdown to the ash pond). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT LIMITS MONITORING REQUIREMENTS Monthly Daily. Measurement Type Sample CHARACTERISTICS Average Maximum FrequencySample Location2 Flow Continuous pump Logs Effluent during discharge Free Available Chlorine3 200 µg/L 500 µg/L 2/month Multiple Grabs Effluent Total Residual Chlorine3 Monthly Multiple Grabs Effluent Total Chromium4 200 µ /L 200 µ /L 2/Month Composite Effluent Total Zinc4 1.0 m /L 1 1.0 m L 2/Month Composite Effluent The 126 Priority Pollutants (40 CFR Part 423, Appendix No Detectable Amount Annual Grab Effluent A) Exclusive of Zinc and Chromium4 Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Effluent sampling shall be conducted at the discharge from the cooling tower prior to mixing with other waste streams. Samples taken in compliance with the monitoring requirements listed above shall be taken prior to mixing with other sources of wastewater 3. Neither free available chlorine nor total residual chorine may be discharged from any single generating unit for more than two hours per day, unless the Permittee demonstrates to the Division that discharge for more than two hours is required for macroinvertebrate control. The 500 µg/L is a daily maximum limitation and is to be measured during the chlorine release period. The 200 µg/L limitation is an average during the chlorine release period. Monitoring is required only when chlorine is added to the cooling water system. 4. These limitations and monitoring requirements apply if these substances are added by the Permittee for cooling tower maintenance. There shall be no detectable amounts of the 126 priority pollutants (40 CFR 423 Appendix A) contained in chemicals added for cooling tower except for total chromium and total zinc. Compliance with the limitations for the 126 priority pollutants in 40 CFR Section 423.13(d)(1) may be determined by engineering calculations which demonstrate that the regulated pollutants are not detectable in the final discharge by the analytical methods in 40 CFR Part 136. Discharge of blowdown from the cooling tower is defined as the minimum discharge of recirculation water necessary for the purpose of discharging materials contained in the process, the further build-up of which would cause concentration in amounts exceeding limitations established by best engineering practice. The Permittee is authorized to discharge Maintenance Drain wastewater from the Cooling Tower for Unit 4 directly to the discharge canal. Grab samples of the following parameters are to be collected prior to mixing with other waste streams and the results shall be submitted to DWR: pH (SU), flow (MGD) and total residual chlorine (mg/L). The Permittee shall notify the Division Page 9 of 23 Permit NC0003425 of Water Resources, Raleigh Regional Office, prior to draining the cooling tower, except during non -office hour emergencies when notification must be made the next working day. Total residual chlorine monitoring is required prior to a maintenance drain of the Unit 4 Cooling Tower only if chlorine is added to the system. A. (6) Effluent Limitations and Monitoring Requirements (Outfall 006) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Outfall 006 (Coal Pile Runoff Treatment System to the Hyco Reservoir). Such discharges shall be limited and monitored' by the Permittee as specified below: LIMITS MONITORING REQUIREMENTS EFFLUENT Monthly Instantaneous Measurement Sample Type Sample CHARACTERISTICS Average Maximum Frequency Location2 Flow 2/Month Estimate Effluent Total Suspended 30 mg/L 50 mg/L 2/Month Grab Effluent Solids Total Selenium Quarterly Grab Effluent pH3 Weekly Grab Effluent Acute Toxicit 4 Annually Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Effluent sampling shall be conducted at the point of discharge into Hyco Reservoir. Samples taken in compliance with the monitoring requirements listed above shall be taken prior to mixing with other sources of wastewater. 3. The pH shall not be less than 6.0 standard units nor greater than 9.0 standard units. 4. Acute Toxicity (Pimephales promelas, 24-hour) monitoring shall be performed in accordance with Special Condition A. (15) of this permit. There shall be no discharge of floating solids or visible foam in other than trace amounts outside a distance five (5) meters from the discharge pipe. Material storage runoff shall include rainfall to navigable waters through any discernable, confined and/or discrete conveyance from, or through, coal. Page 10 of 23 Permit NC0003425 A. (7) Effluent Limitations and Monitoring Requirements (Internal Outfall 008) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expansion to 0.025 MGD or expiration, the Permittee is authorized to discharge from Internal Outfall 008 (Domestic Wastewater Treatment System). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS DAILY MAXIMUM MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample Location2 Flow 0.015 MGD Annual Pump Los Effluent Biochemical Oxygen Demand 5-day20°C 30.0 mg/L 45.0 mg/L Annual Grab Effluent Total Suspended Solids 30.0 m L 45.0 m L Annual Grab Effluent Total Ammonia as N Annual Grab Effluent H3 Annual Grab Effluent Fecal Coliform 200 100 ml 400 100 ml Annual Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after treatment and prior to mixing with other sources of wastewater. 3. The pH shall not be less than 6.0 standard units, nor greater than 9.0 standard units. See Special Condition A (22). A. (8) Effluent Limitations and Monitoring Requirements (Internal Outfall 008) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning upon expansion to 0.025 MGD and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 008 (Domestic Wastewater Treatment System). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS DAILY MAXIMUM MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample Location2 Flow 0.025 MGD Annual Pump Los Effluent Biochemical Oxygen Demand 5- ay @ 20°C 30.0 mg/ L 45.0 mg/ L Annual Grab Effluent Total Suspended Solids 30.0 m / L 45.0 m / L Annual Grab Effluent Total Ammonia (as N) Annual Grab Effluent PH3 Annual Grab Effluent Fecal Coliform 200/ 100 ml 400/ 100 ml Annual Grab Effluent Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after treatment and prior to mixing with other sources of wastewater. 3. The pH shall not be less than 6.0 standard units, nor greater than 9.0 standard units. Page 11 of 23 Permit NC0003425 See Special Condition A (22). A. (9) Effluent Limitations and Monitoring Requirements (Internal Outfall 009) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 009 (Metal Cleaning Wastes). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily Maximum Measurement Frequency Sample Type Sample z Location Flow Once per Discharge Event Pump Logs or similar reading Outfall 002 Total Suspended Solids 30.0 mg/L 100 mg/L Once per Discharge Event Grab Outfall 002 Oil and Grease 15.0 mg/L 20.0 mg/L Once per Discharge Event Grab Outfall 002 Total Copper 1.0 mg/L 1.0 mg/L Once per Discharge Event Grab Outfall 002 Total Iron 1.0 m /L 1.0 m /L Once per Discharge Event Grab Outfall 002 Notes: 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after ash pond treatment and prior to mixing with other sources of wastewater. For the purposes of this permit, the term "Once per Discharge Event" shall mean the discharge from Outfall 002 that occurs within 30 minutes from the time the fly ash containing metal cleaning waste is discharged into the ash pond plus the calculated detention time of the ash pond. A. (10) Effluent Limitations and Monitoring Requirements (Internal Outfall 010) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning on the effective date of the permit and lasting until the existing treatment system is decommissioned, the Permittee is authorized to discharge from Internal Outfall 010 (FGD blowdown). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily [Maximum Measurement Frequency Sample Type Sample Location2 Flow Monthly Pump Logs or similar reading Effluent Total Suspended Solids 30 m /l 100 m /l Quarterly Grab Effluent Oil and grease 15 m /l 20 m /l Quarterly Grab Effluent Total Arsenic 3 8 µ /l 11 µ /l Quarterly Garb Effluent Total Mercury 3 356 n 1 788 n 1 Quarterly Grab Effluent Total Selenium 3 12 1 23 1 Quarterly Grab Effluent Nitrate Nitrite as N 3 4.4 mg/1 17 mg/1 Quarterly Grab Effluent Notes 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). Page 12 of 23 Permit NC0003425 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after bioreactor treatment and prior to mixing with other sources of wastewater. 3. The limits shall become effective December 23, 2023. 4. The pH shall not be less than 6.0 standard units, nor greater than 9.0 standard units. A. (11) Effluent Limitations and Monitoring Requirements (Internal Outfall 011) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning upon the commencement of operations of the new FGD system and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 011 (FGD blowdown). Such discharges shall be limited and monitored' by the Permittee as specified below: EFFLUENT CHARACTERISTICS LIMITS MONITORING REQUIREMENTS Monthly Average Daily [Maximum Measurement Frequency Sample Type Sample Location2 Flow Monthly Pump Logs or similar reading Effluent Total Suspended Solids 30 mg/l 100 mg/1 Quarterly Grab Effluent Oil and grease 15 mg/l 20 mg/1 Quarterly Grab Effluent Total Arsenic 3 8 µ 1 11 µ l Quarterly Garb Effluent Total Mercury 3 356 n 1 788 n 1 Quarterly Grab Effluent Total Selenium 3 1 12 µ 1 1 23 µ 1 I Quarterly I Grab I Effluent Nitrate/Nitrite as N 3 1 4.4 mg/1 1 17 mg/1 I Quarterly I Grab I Effluent Notes•. 1.Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after bioreactor treatment and prior to mixing with other sources of wastewater. 3. The limits shall become effective December 23, 2023. A. (12) Effluent Limitations and Monitoring Requirements (Internal Outfall 012) [15A NCAC 02B .0400 et seq., 02B .0500 et seq.] During the period beginning upon the start of operation of the retention basin and lasting until expiration, the Permittee is authorized to discharge from Internal Outfall 012 (Low volume wastes Retention Ponds). Such discharges shall be limited and monitored' by the Permittee as specified below: LIMITS MONITORING REQUIREMENTS EFFLUENT Monthly Daily [Maximum Measurement Sample Type Sample CHARACTERISTICS Average Frequency Location2 Flow Monthly Pump Logs or Effluent similar reading Total Suspended Solids 30 mg/1 100 mg/1 Quarterly Grab Effluent Oil and grease 15 mg/l 20 mg/l Quarterly Grab Effluent Notes 1. Starting on December 21, 2016, begin submitting Discharge Monitoring Reports electronically using NC DWR's eDMR application system. Please See Special Condition A. (29). Page 13 of 23 Permit NC0003425 2. Samples taken in compliance with the monitoring requirements listed above shall be taken after retention pond and prior to mixing with other sources of wastewater. A.(13) Seeps If new seeps to waters of the state are identified, the facility shall follow the procedures outlined below. The deadlines for new seeps shall be calculated from the date of the seep discovery. The new identified seep is not permitted until the permit is modified and the new seep included in the permit and the new outfall established for the seep. For all new water seeps to waters of the state, the facility shall determine within 90 days from the seep discovery if a seep meets the state water quality standards established in 15A NCAC 2B .0200 and submit the results of this determination to the Division. If the standards are not contravened, the facility shall conduct monitoring for the parameters specified in A. (1). If any of the water quality standards are exceeded, the facility shall be considered in violation of the Clean Water Act until one of the options below is fully implemented. The facility shall: 1) Submit a complete application for 404 Permit (within 30 days after determining that a water quality standards is exceeded) to pump the seep discharge to one of the existing outfalls, install a pipe to discharge the seep to the Catawba River, or install an in -situ treatment system. After the 404 Permit is obtained, the facility shall complete the installation of the pump, pipe, or treatment system within 180 days from the date of the 404 permit receipt and begin pumping/discharging or treatment. 2) Demonstrate through modeling that the decanting and dewatering of the ash basin will result in the elimination of the seep and submit the modeling results to the Division within 120 days from the seep discovery. Within 180 days from the completion of the dewatering the facility shall confirm that the seep flow ceased. If the seep flow continues, the facility shall choose one of the other options in this Special Condition. 3) Demonstrate that the seep is discharging through the designated "Effluent Channel' or permitted outfall and the water quality standards in the receiving stream are not contravened. This demonstration should be submitted to the Division no later than 180 days from the seep discovery. The "Effluent Channel' designation should be established by the DEQ Regional Office personnel prior to the issuance of the permit and appropriate 404 permit shall be obtained. All effluent limits, including water quality -based effluent limits, remain applicable notwithstanding any action by the Permittee to address the violation through one of the identified options, so that any discharge in exceedance of an applicable effluent limit is a violation of the Permit as long as the seep remains flowing. Page 14 of 23 Permit NC0003425 A. (14) Acute Toxicity Testing PASS/ FAIL Permit Limit Outfalls 001 and 003 [15A NCAC 02B .0200 et seq.] The Permittee shall conduct acute toxicity tests on a quarterly basis using protocols defined in the North Carolina Procedure Document entitled "Pass/Fail Methodology For Determining Acute Toxicity In A Single Effluent Concentration" (Revised -December 2010 or subsequent versions). The monitoring shall be performed as a Fathead Minnow (Pimephales promelas) 24 hour static test. The effluent concentration at which there may be at no time significant acute mortality is 90% (defined as treatment two in the procedure document). The tests will be performed during the months of. These months signify the first month of each three month toxicity testing quarter assigned to the facility. Effluent sampling for this testing must be obtained during representative effluent discharge and shall be performed at the NPDES permitted final effluent discharge below all treatment processes. The Permittee shall conduct acute toxicity tests on a _quarterly basis using protocols defined in the North Carolina Procedure Document entitled "Pass/Fail Methodology For Determining Acute Toxicity In A Single Effluent Concentration" (Revised -December 2010 or subsequent versions). The monitoring shall be performed as a Fathead Minnow (Pimephales promelas) 24 hour static test. The effluent concentration at which there may be at no time significant acute mortality is 90% (defined as treatment two in the procedure document). The tests will be performed during the months of March, June, September and December. These months signify the first month of each three month toxicity testing quarter assigned to the facility. Effluent sampling for this testing must be obtained during representative effluent discharge and shall be performed at the NPDES permitted final effluent discharge below all treatment processes. The parameter code for Pimephales promelas is TGE6C. All toxicity testing results required as part of this permit condition will be entered on the Effluent Discharge Form (MR-1) for the month in which it was performed, using the appropriate parameter code. Additionally, DWR Form AT-2 (original) is to be sent to the following address: Attention: North Carolina Division of Water Resources Water Sciences Section/Aquatic Toxicology Branch 1623 Mail Service Center Raleigh, North Carolina 27699-1623 Completed Aquatic Toxicity Test Forms shall be filed with the Water Sciences Section no later than 30 days after the end of the reporting period for which the report is made. Test data shall be complete and accurate and include all supporting chemical/physical measurements performed in association with the toxicity tests, as well as all dose/response data. Total residual chlorine of the effluent toxicity sample must be measured and reported if chlorine is employed for disinfection of the waste stream. Should there be no discharge of flow from the facility during any month, the Permittee will complete the information located at the top of the aquatic toxicity (AT) test form indicating the facility name, permit number, pipe number, county, and the month/year of the report with the notation of "No Flow" in the comment area of the form. The report shall be submitted to the Water Sciences Section at the address cited above. Should the Permittee fail to monitor during a month in which toxicity monitoring is required, then monthly monitoring will begin immediately. Upon submission of a valid test, this monthly test requirement will revert to quarterly in the months specified above Should any test data from either these monitoring requirements or tests performed by the North Carolina Division of Water Resources indicate potential impacts to the receiving stream, this permit may be re -opened and modified to include alternate monitoring requirements or limits. Page 15 of 23 Permit NC0003425 NOTE: Failure to achieve test conditions as specified in the cited document, such as minimum control organism survival and appropriate environmental controls, shall constitute an invalid test and will require immediate follow-up testing to be completed no later than the last day of the month following the month of the initial monitoring. A. (15) Acute Toxicity Monitoring (ANNUAL) Outfall 006 [15A NCAC 02B .0200 et seq.] The permittee shall conduct annual acute toxicity tests using protocols defined as definitive in EPA Document EPA-82 1 -R-02-012 entitled "Methods for Measuring the Acute Toxicity of Effluents and Receiving Waters to Freshwater and Marine Organisms." The monitoring shall be performed as a Fathead Minnow (Pimephales promelas) 48 hour static test. Effluent samples for self -monitoring purposes must be obtained during representative effluent discharge and shall be performed at the NPDES permitted final effluent discharge below all waste treatment processes. The parameter code for Pimephales promelas is TAA6C. All toxicity testing results required as part of this permit condition will be entered on the Effluent Discharge Form (MR-1) for the month in which it was performed, using the appropriate parameter code. Additionally, DWR Form AT-1 (original) is to be sent to the following address: Attention: North Carolina Division of Water Resources Water Sciences Section/Aquatic Toxicology Branch 1623 Mail Service Center Raleigh, North Carolina 27699-1623 Completed Aquatic Toxicity Test Forms shall be filed with the Water Sciences Section no later than 30 days after the end of the reporting period for which the report is made. Test data shall be complete and accurate and include all supporting chemical/physical measurements performed in association with the toxicity tests, as well as all dose/response data. Total residual chlorine of the effluent toxicity sample must be measured and reported if chlorine is employed for disinfection of the waste stream. Should there be no discharge of flow from the facility during any month, the permittee will complete the information located at the top of the aquatic toxicity (AT) test form indicating the facility name, permit number, pipe number, county, and the month/year of the report with the notation of "No Flow" in the comment area of the form. The report shall be submitted to the Water Sciences Section at the address cited above. Should any test data from either these monitoring requirements or tests performed by the North Carolina Division of Water Resources indicate potential impacts to the receiving stream, this permit may be re -opened and modified to include alternate monitoring requirements or limits. NOTE: Failure to achieve test conditions as specified in the cited document, such as minimum control organism survival and appropriate environmental controls, shall constitute an invalid test and will require immediate follow-up testing to be completed no later than the last day of the month following the month of the initial monitoring. A. (16) Intake Screen Backwash Condition Continued intake screen backwash discharge is permitted without limitations or monitoring requirements. Page 16 of 23 Permit NC0003425 A. (17) Temperature Requirements (Outfall 003 Mixing Zone) a. Water quality standards for temperature for lower piedmont waters (32' C) will not apply within a mixing zone, which shall include the North Hyco arm downstream of NC Highway 57, the main body of Hyco Reservoir downstream of the confluence of the Cobbs Creek Arm and the North Hyco Arm, and the entire afterbay lake. The area described does not include the South Hyco Arm or the first finger arms on the west side of the reservoir lying upstream of the dam. Water within the main lake and the afterbay lake to Hyco River shall comply with water quality standards except the temperature standards in the areas of the lake defined herein as a mixing zone. Water discharged from the afterbay shall comply with the temperature standard. b. Temperature measurements made to monitor compliance with this provision shall be made at least six inches, but not more than one foot, below the surface of the lake. A monthly average temperature shall consist of at least five determinations conducted on five separate days. c. Temperature increases shall be determined as the increase in temperature above the temperature measured at the confluence of the two southern finger arms on the north side of the lake (Lat. 36.5111, Long 79.06629). d. A summary of the temperature monitoring results pursuant to A. (16) a. through c. shall be submitted to the Division with the annual Biological Monitoring Report due by July 31 of the following year. A. (18) Biological and Instream Monitoring In accordance with the previously submitted biological monitoring program (as approved by the Director of the Division, and as it may be amended), the Permittee shall submit results of biological studies and monitoring programs by July 31 of the following year. The following parameters shall be included in the surface water sampling protocol: total arsenic, total selenium, total mercury (method 1631E), total chromium, total lead, total cadmium, total copper, total hardness, and total zinc. For fish tissue sampling the following parameters shall be included: arsenic, selenium and mercury. Copies of all the study plans, study results, and any other applicable materials should be submitted to: 1) Electronic Version Only (PDF and CD) Division of Water Resources WQ Permitting Section - NPDES 1617 Mail Service Center Raleigh, NC 27699-1617 2) Electronic Version (PDF and CD) and Hard Copy Division of Water Resources Water Sciences Section 1621 Mail Service Center Raleigh, NC 27699-1623 A. (19) Applicable State Law This facility shall meet the requirements of Senate Bill 729 (Coal Ash Management Act). This permit may be reopened to include new requirements imposed by Bill 729. A. (20) PCB Prohibition There shall be no discharge of polychlorinated biphenyl compounds such as those commonly used for transformer fluid. Page 17 of 23 Permit NC0003425 A. (21) Limitations Reopener The permit shall be modified, or revoked and reissued, to comply with any applicable effluent guideline or water quality standard issued or approved under sections 302(b)(2)(c) and (d), 304(b)(2) and 307(a) of the Clean Water Act, if the effluent guideline or water quality standard so issued or approved: a. Contains different conditions or is otherwise more stringent than any effluent limitation in the permit; or b. Controls a pollutant not limited in the permit. The permit as modified or reissued under this paragraph shall also contain any other requirements in the Act then applicable. A. (22) Domestic Wastewater Treatment Plant The permittee shall at all times properly operate and maintain the domestic wastewater treatment plant to meet secondary standards as specified for internal outfall 008. A. (23) Bioreactor Condition An operation and maintenance plan, including a monitoring regimen for the bioreactor units and an emergency response plan in the event of an upset, shall be maintained and available for inspection by Division personnel. A. (24) Ash Pond Closure The facility shall prepare an Ash Ponds Closure Plan. This Plan shall be submitted to the Division one month prior to the closure of ash ponds. A. (25) Groundwater Monitoring Well Construction And Sampling The permittee shall conduct groundwater monitoring to determine the compliance of this NPDES permitted facility with the current groundwater Standards found under 15A NCAC 2L .0200. The monitoring shall be conducted in accordance with the Sampling Plan approved by the Division. See Attachment 1. A. (26) Clean Water Act Section 316(b) The permittee shall comply with the Cooling Water Intake Structure Rule per 40 CFR 125.95. The permittee shall submit all the materials required by the Rule with the next renewal application. Copies of all the study plans, study results, and any other applicable materials should be submitted to: 1) Electronic Version Only (PDF and CD) Division of Water Resources WQ Permitting Section - NPDES 1617 Mail Service Center Raleigh, NC 27699-1617 2) Electronic Version (PDF and CD) and Hard Copy Division of Water Resources Water Sciences Section 1623 Mail Service Center Raleigh, NC 27699-1623 Page 18 of 23 Permit NCO003425 A. (27) Structural Integrity Inspections of Ash Pond Dam The facility shall meet the dam design and dam safety requirements per 15A NCAC 2K as amended by statute. A. (28) Biocide Condition The permittee shall not use any biocides except those approved in conjunction with the permit application. The permittee shall notify the Director in writing not later than ninety (90) days prior to instituting use of any additional biocide used in cooling systems which may be toxic to aquatic life other than those previously reported to the Division of Water Resources. Such notification shall include completion of Biocide Worksheet Form 101 and a map locating the discharge point and receiving stream. Completion of Biocide Worksheet Form 101 is not necessary for those outfalls containing toxicity testing. Division approval is not necessary for the introduction of new biocides into outfalls currently tested for whole effluent toxicity. A. (29) Electronic Reporting of Discharge Monitoring Reports [G.S. 143-215.1(b)] Federal regulations require electronic submittal of all discharge monitoring reports (DMRs) and program reports and specify that, if a state does not establish a system to receive such submittals, then permittees must submit monitoring data and reports electronically to the Environmental Protection Agency (EPA). The final NPDES Electronic Reporting Rule was adopted and became effective on December 21, 2015. NOTE: This special condition supplements or supersedes the following sections within Part II of this permit (Standard Conditions for NPDES Permits): • Section B. (11.) Signatory Requirements • Section D. (2.) • Section D. (6.) • Section E. (5.) Reporting Records Retention Monitoring Reports 1. Reporting Requirements [Supersedes Section D. (2.) and Section E. (5.) (a)] Effective December 21, 2016, the permittee shall report discharge monitoring data electronically using the NC DWR's Electronic Discharge Monitoring Report (eDMR) internet application. Monitoring results obtained during the previous month(s) shall be summarized for each month and submitted electronically using eDMR. The eDMR system allows permitted facilities to enter monitoring data and submit DMRs electronically using the internet. Until such time that the state's eDMR application is compliant with EPA's Cross -Media Electronic Reporting Regulation (CROMERR), permittees will be required to submit all discharge monitoring data to the state electronically using eDMR and will be required to complete the eDMR submission by printing, signing, and submitting one signed original and a copy of the computer printed eDMR to the following address: NC DENR / Division of Water Resources / Water Quality Permitting Section ATTENTION: Central Files 1617 Mail Service Center Raleigh, North Carolina 27699-1617 If a permittee is unable to use the eDMR system due to a demonstrated hardship or due to the facility being physically located in an area where less than 10 percent of the households have broadband access, then a temporary waiver from the NPDES electronic reporting requirements may be granted and discharge monitoring data may be submitted on paper DMR forms (MR 1, 1. 1, 2, 3) or alternative forms approved by the Director. Duplicate signed Page 19 of 23 Permit NC0003425 copies shall be submitted to the mailing address above. See "How to Request a Waiver from Electronic Reporting" section below. Regardless of the submission method, the first DMR is due on the last day of the month following the issuance of the permit or in the case of a new facility, on the last day of the month following the commencement of discharge. Starting on December 21, 2020, the permittee must electronically report the following compliance monitoring data and reports, when applicable: • Sewer Overflow/Bypass Event Reports; • Pretreatment Program Annual Reports; and • Clean Water Act (CWA) Section 316(b) Annual Reports. The permittee may seek an electronic reporting waiver from the Division (see "How to Request a Waiver from Electronic Reporting" section below). 2. Electronic Submissions In accordance with 40 CFR 122.41(1)(9), the permittee must identify the initial recipient at the time of each electronic submission. The permittee should use the EPA's website resources to identify the initial recipient for the electronic submission. Initial recipient of electronic NPDES information from NPDES-regulated facilities means the entity (EPA or the state authorized by EPA to implement the NPDES program) that is the designated entity for receiving electronic NPDES data [see 40 CFR 127.2(b)]. EPA plans to establish a website that will also link to the appropriate electronic reporting tool for each type of electronic submission and for each state. Instructions on how to access and use the appropriate electronic reporting tool will be available as well. Information on EPA's NPDES Electronic Reporting Rule is found at: http: / / www2. epa. gov / compliance / final-national-pollutant-discharge-elimination-system- npdes-electronic-reporting-rule. Electronic submissions must start by the dates listed in the "Reporting Requirements" section above. 3. How to Request a Waiver from Electronic Reporting The permittee may seek a temporary electronic reporting waiver from the Division. To obtain an electronic reporting waiver, a permittee must first submit an electronic reporting waiver request to the Division. Requests for temporary electronic reporting waivers must be submitted in writing to the Division for written approval at least sixty (60) days prior to the date the facility would be required under this permit to begin submitting monitoring data and reports. The duration of a temporary waiver shall not exceed 5 years and shall thereupon expire. At such time, monitoring data and reports shall be submitted electronically to the Division unless the permittee re -applies for and is granted a new temporary electronic reporting waiver by the Division. Approved electronic reporting waivers are not transferrable. Only permittees with an approved reporting waiver request may submit monitoring data and reports on paper to the Division for the period that the approved reporting waiver request is effective. Information on eDMR and the application for a temporary electronic reporting waiver are found on the following web page: http: / / deg. nc.gov/ about / divisions /water -resources / edmr Page 20 of 23 Permit NC0003425 4. Signatory Requirements [Supplements Section B. 111.1 (bland Supersedes Section B. 11. d All eDMRs submitted to the permit issuing authority shall be signed by a person described in Part II, Section B. (11.) (a) or by a duly authorized representative of that person as described in Part II, Section B. (11.)(b). A person, and not a position, must be delegated signatory authority for eDMR reporting purposes. For eDMR submissions, the person signing and submitting the DMR must obtain an eDMR user account and login credentials to access the eDMR system. For more information on North Carolina's eDMR system, registering for eDMR and obtaining an eDMR user account, please visit the following web page: http: / / deg. nc.gov / about / divisions /water -resources / edmr Certification. Any person submitting an electronic DMR using the state's eDMR system shall make the following certification [40 CFR 122.22]. NO OTHER STATEMENTS OF CERTIFICATION WILL BE ACCEPTED: 7 certify, under penalty of law, that this document and all attachments were prepared under my direction or supervision in accordance with a system designed to assure that qualified personnel properly gather and evaluate the information submitted. Based on my inquiry of the person or persons who manage the system, or those persons directly responsible for gathering the information, the information submitted is, to the best of my knowledge and belief, true, accurate, and complete. I am aware that there are significant penalties for submitting false information, including the possibility of fines and imprisonment for knowing violations. " 5. Records Retention [Supplements Section D. (6.11 The permittee shall retain records of all Discharge Monitoring Reports, including eDMR submissions. These records or copies shall be maintained for a period of at least 3 years from the date of the report. This period may be extended by request of the Director at any time [40 CFR 122.411. A. (30) Additional Conditions and Definitions The following special conditions are applicable to all outfalls regulated by this permit: a) Nothing contained in this permit shall be construed as a waiver by the permittee of any right to a hearing it may have pursuant to State or Federal laws or regulations. b) Discharge of any waste resulting from the combustion of toxic or hazardous waste to any waste stream which ultimately discharges to waters of the United States is prohibited, unless specifically authorized in this permit. c) The permittee shall report all visible discharges of floating materials (such as an oil slick) to the Director when submitting DMRs. d) "Upset," means an exceptional incident in which there is an unintentional and temporary non-compliance with technology -based effluent limitations because of factors beyond the reasonable control of the permittee. An upset does not include noncompliance to the extent cause by operational error, improperly designed treatment facilities, inadequate treatment facilities, lack of preventative maintenance, or improper operations. e) All flows shall be reported on monthly DMRs. Should no flow occur during a given month, the words "no flow" should be clearly written on the front of the DMR. fl EPA methods 200.7 or 200.8 (or the most current versions) shall be used for analyses of all metals except for total mercury. g) All effluent samples for all external outfalls shall be taken at the most accessible location after the final treatment but prior to discharge to waters of the U.S. (40 CFR 122.41(j)). Page 21 of 23 Permit NC0003425 h) The term low volume waste sources means wastewater from all sources except those for which specific limitations are otherwise established in this part (40 CFR 423.11 (b)). i) The term chemical metal cleaning waste means any wastewater resulting from cleaning any metal process equipment with chemical compounds, including, but not limited to, boiler tube cleaning (40 CFR 423.11 (c)). j) The term metal cleaning waste means any wastewater resulting from cleaning [with or without chemical cleaning compounds] any metal process equipment including, but not limited to, boiler tube cleaning, boiler fireside cleaning, and air preheater cleaning (40 CFR 423.11 (d)). k) For all outfalls where the flow measurement is to be "estimated" the estimate can be done by using calibrated V-notch weir, stop -watch and graduated cylinder, or other method approved by the Division. Page 22 of 23 Permit NC0003425 Duke Energy Progress — Roxboro Facility Facility Location Person County Receiving Stream: Hyco Reservoir Stream Class: WS-V, B Sub -Basin: 03-02-05 State Grid: B22NE/Olive Hill N Drainage Basin: Roanoke River Basin • Outfall 001: Latitude 36' 29' 10" Longitude 79° 03' 34" Outfall 003: Latitude 36' 28' 48" Longitude 79° 05' 11" Outfall 006: Latitude 36° 19' 13" Longitude 79' 04' 41" NPDES Permit NC0003425 Page 23 of 23