20210709_App_92-13

July 8, 2021
RECEf VED
JUL 0 91011
LAND QUALITY
MINING PROGRAM
■■■
■■■
"'Hanson
HEIDELBERGCEMENTGrou p
Hanson Aggregates Southeast, LLC
South Region
North Carolina Territory Office
3825 Barrett Drive, Suite 300
Morrisville, NC 27560-9626
Tel [phone]
Fax [phone]
w .lehiahhanson.com
RECEIVED
Mr. Adam Parr, Mining Engineer 2021
NC Department of Environmental Quality
Division of Energy, Mineral, and Land Resources LAND QUALITY
512 North Salisbury Street, Archdale Bldg, Room 504 MINING PROGRAM
Raleigh, NC 27604
Subject: Hanson Aggregates Southeast, LLC — Holly Springs Quarry
NC Mine Permit No. 92-13 Mine Modification Application Submittal
Wake Forest, Wake County, North Carolina
Dear Mr. Parr:
Hanson recently acquired four (4) properties totaling about 107 acres, located north
of the existing mine permitted site. The tracts were annexed to the Town of Holly Springs
and ultimately rezoned to accommodate the installation of visual screening berms,
overburden storage piles, corresponding sediment basins and traps, and storage of
construction equipment. Hanson is hereby submitting a mine modification application to
add these tracts to its mine permitted acreage and to install screening berms, overburden
storage piles, and related sediment basins as shown on the M&ECP-2 Mine Map.
Notifications have been mailed via certified mail and receipt request to the adjacent
property owners to the following tracts to be added to the mine permit. Please see the
copies of the notification affidavit and notices w/maps included in the mine application.
Tract
Name
Owner
Nores
PIN #
REID
Address
Kenney
Hanson
Aggregates
SE
LLC
19.60
0637378113
0047596
6200
Rex
Road
Powell
Hanson
Aggregates
SE
LLC
19.20
0637363113
0047692
6120
Rex
Road
Powell
Hanson
Aggregates
SE
LLC
12.66
0637463580
0056 553
6212
Rex
Road
Powell
Hanson
Aggregates
SE
LLC
54.81
0637565912
0056853
6312
Rex
Road
Secondly, Hanson is requesting to expand its existing mine excavation pit into its
southwestern corner of the existing mine permitted property. This expansion will increase
the mine excavation by about 43 acres. Included as a step to take prior the actual
southwestern pit expansion is to slightly expand or widen the pit entrance enough to allow
for either two (2) lanes of traffic or one (one) lane of traffic plus an overland conveyor.
Please see the portion of haul road and area next to the primary to be expanded into the
mine excavation pit acreage and the southwest pit expansion.

`4 _'vcr
„r�.,e
n,
eas
% 1
`
.
FadeyYmi6i•r
,
ti
,y�e,,.
,•eq�t,fe•• e[,,,,.n�m IltSutl�mNl
_Y n„frf
•w •.��
ri ,mr
__ ApAOi
-, QMNI6EMAY
AigIAD FEND
,Fa�w
PgOIKTIDt1 A'
.
�I
-
POtlD 011itEi
_ M/f
EI zq"E CY
Sp WAYW
ourtiiNfO
\e
A
To prepare for the pit expansion, (1) Retention Pond #4 will need to be constructed
so that Retention Ponds 2 & 3 can be drained and become a part of the pit, and (2) the
following wetland and stream features will need to be mitigated with the purchase of
credits: Wetland Area #1 = 0.06 acres, Stream C = 0.02 acres & 171 linear feet, and
Stream E = 0.03 acres & 328 linear feet. The retention ponds 1 & 2 and associated
streams and wetlands were determined to be excusive due the fact that all were permitted
in the original mine permit as water treatment structures. Since there have been numerous
changes in plans, the USACE has requested that S&EC, our contracted agent, prepare a
JD request covering all aspects of the project. Until such a JD is obtained, Hanson is
submitting a finalized map showing the USACE and DWR determinations and email
correspondence from James Lastinger with the USACE.
As a minor part the pit expansion, Hanson is requesting that it be permitted to
extend the northern pit limits to a line parallel and fifty (50) feet from the intermittent stream
high water mark. This will allow for a better pit design with less inward corners. Please see
the below comparison between existing (gray dashed line) and proposed (black dashed
line).
po. is
'�.;wd,r�y Trap u
$$ IE mgl
BYrIY
�{Earsryl
' SDOu
,s 'swer,di4.�
CAvarlFSb
s
�CnrA Qan ^•^- fig _.
aDOXV
% pP
V fiFl
plpo '
RM prt ...
PR WRS
1mm K' tsuttw. uAA
FIITUPE F1T li1rtS
.....t. 1
\ pit
1P

The USACE and DWR made determinations on the newly acquired Powell and
Kinney tracts, and those determinations can be found on the previously mentioned
finalized USACE & DWR map prepared by S&EC; however, there are two (2) features that
Hanson is requesting that the USACE determine exclusive. The features are (1) Feature F
exclusion as an ephemeral channel and (2) WI wetland that is less than 0.10 acres and
could be excluded. Depending on those calls, Hanson will either impact the features with
overburden pile construction or avoid the features by flagging a 50-foot undisturbed buffer
around each feature. Please see the below portion of the M&ECP-2 Mine Map showing the
subject features.
W13 Wetland = 0.08 acres
Due to the north -to -south size of the property, we have shown the pit expansion on
the M&ECP-1 Mine Map and the addition of the Powell and Kenney tracts on the next
page, M&ECP-2 Mine Map. To better locate and identify the overburden piles (OB Piles),
ID Numbers were assigned and placed on the maps. Below is a table identifying the OB
piles, the drainage areas and associated sediment basins. Calculation for the Basins 21
thru 28 can be found in the attached E&SC Modifications packet prepared by Andrew
Mericle with Draper Aden Associates. A table with the sediment basin specifications for
Basins 10 and 21 thru 28 can be found in the top right corner of X-4 Details Mine Map.
Retention Pond specifications can be found on the X-3 Details Map labeled "Retention
Dam".
Overburden
Description
Drainage
Drainage
Sediment Basin(s)
Pile ID No.
Area(s)
Area Acreage
OB-1
Existing OB pile stabilized
S13-10, later Retention Pond #4
years ago
OB-2
Existing OB Pile
SB-10, later Retention Pond #4
OB-3
Appro%ed OB Pile increased
DA-21
13.67
SB-21
due to Powell acquisition
Contains the W13 Wetland
DA-22
9.68
013-4 East
that is <_ 0.10 acres and a
DA-23
8.22
SB-22 and SB-23
part of Feature "F"
0134 West
Contain most of Feature "F,
DA-24
8.49
SB-24 and SB-25
DA-25
4.54
0134 North
North side of the OB-4 Pile
DA-26
22.49
SB-26
Accessed by RC-1; see Xing
013-5
detail on X4 Detail Map
DA-27
3.09
SB-27
OB-6
Accessed by RC-2; see Xing
DA-28
8.81
SB-28
detail on X-4 Detail Map
Another change added to this modification is the lowering of the final mine floor
from EL = 75 feet to EL = -15 feet on the X-2 Details Map so that the final floor shown on
the map will agree with the maximum mining depth stated in previously approved mine
applications. With natural ground elevation at EL = 305 feet and the approved 320 feet of

maximum mining depth, the final mine floor should be EL = 15 feet below sea level; not EL
= 75 feet as indicated on the previously approved mine maps. Hanson has been working
with DELMR to get the mine maps from all our sites to agree with the approved mine
applications during subsequent mine modification submittals. The X-2 Mine Map has been
revised to reflect the previously approved 320 feet of maximum mining depth from the
application by showing the final mine floor at EL = -15 feet.
A complete set of mine maps has been included to reflect the attached mine permit
modification application. Enclosed please find the following:
- 1 (one) original mine application cover letter and 5 (five) copies
- 1 (one) original mine application, project description, and 5 (five) copies
- 1 (one) original set of mine and reclamation plans and 5 (five) copies
- 1 (one) original set of erosion control modification calculations and 5 (five) copies
- 6 copies of the post USACE & DWR determination map of the Powell / Kinney tracts
- 6 copies of the CFRRO #17-264 DWR determination dated 9/27/2017
- 6 copies of the CFRRO #19-342 DWR determination dated 11/13/2019
- 6 copies of Yr-2018 USACE/S&EC/Hanson email correspondence: certain exclusions
- 6 copies of Yr-2021 USACE/S&EC/Hanson email correspondence: certain exclusions
- 1 (one) Check No. 100086 for $1,000.00 mine permit modification processing fee
Should you have any questions or need additional information, please contact me at our
Raleigh office: [phone], Jack. GarvevCa)lehiohhanson.com , and you may also
contact our contracted engineer, Andrew Mericle: [phone], americle aodaa.com .
Sincerely,
Jack Garvey, Environmental Manager
Enclosures:
cc: Daren McMorris, NC Operations Manager
Nathan Duryea, Plant Manager
Bob Zarzecki, S&EC
Andrew Mericle, Draper Aden Associates

NORTH CAROLINA
MINING PERMIT APPLICATION
State of North Carolina
Department of Environment Quality
Division of Energy, Mineral, and Land Resources
1612 Mail Service Center
Raleigh, North Carolina 27699-1612
[phone]
Revised: 2017
Mine Permit Modification Application
Hanson Aggregates Southeast LLC
Holly Springs Quarry, NC Mine Permit No. 9243
Holly Springs, Wake County
NORTH CAROLINA DEPARTMENT OF ENVIRONMENTAL QUALITY
July 2021
ME

(PLEASE PRINT OR TYPE)
1. Name of Mine Holly Springs Quarry County Wake
River Basin Cape Fear
Latitude (decimal degrees to four places) 35.60260
Longitude (decimal degrees to four places)-78.8776'
2. Name of Applicant* Hanson Aggregates Southeast LLC.
3. Permanent address for receipt of official mail** 3825 Barrett Drive, Suite 300
Raleigh, NC 27609
Telephone [phone] Alternate No. [phone]
4. Mine Office Address 7000 Cass Holt Road
Holly Springs, NC 27540 Telephone [phone]
Mine Manager Nathan Duryea Plant Manager
6. E-mail Address Nathan.Durve Alehighbanson.com
We hereby certify that all details contained in this Permit Application are true and correct to the best of our
knowledge. We fully understand that any willful misrepresentation of facts will be cause for permit
revocation.
* * * S ignatureQ�-z� QDate July 1, 2021
Print Name Daren McMorris
Title NC Operations Manager
This will be the name that the mining permit will be issued to and the name that must be indicated on the
reclamation bond (security) that corresponds to this site.
** The Division of Energy, Mineral, and Land Resources must be notified of any changes in the permanent
address or telephone number.
*** Signature of company officer required.
G.S. 74-51 provides that the Department shall grant or deny an application for a permit within 60 days of receipt of
a complete application or, if a public hearing is held, within 30 days following the hearing and the filing of any
supplemental information required by the Department. All questions must be addressed and all required maps
provided before this application can be considered complete. Attach additional sheets as needed.
-1-

APPLICATION FOR A MINING PERMIT
■ NOTE: All of the following questions must be thoroughly answered with regards to your mining
operation for the intended life of the mine. All responses must be clearly conveyed on a corresponding,
detailed mine map.
A. GENERAL CHARACTERISTICS OF THE MINE
Answer all of the following that apply:
A. GENERAL CHARACTERISTICS OF THE MINE
1. Answer all of the following that apply:
❑ If this is an application for a NEW permit, indicate the total acreage at the site to be covered by the
permit (this is the acreage that the "new permit" fee will be based upon):
Of this acreage, how much is owned and how much is leased? Acres owned:
Acres leased: Property owner if leased:
❑ If this is an application for RENEWAL of a mining permit, indicate the mining permit number and
the total (overall) acreage covered by the existing permit: Mining Permit No.:
Total permitted acreage (this is the acreage that the "renewal" fee will be based upon):
X If this is an application for a MODIFICATION to a mining permit, indicate the mining permit
number and the total (overall) acreage covered by the existing permit.
Mining Permit No.: 92-13 Total permitted acreage: 286.32
Does the modification involve acreage within the previously approved permitted boundary?
Yes X. No ❑. If yes, indicate the acreage to be covered by this modification (this is the acreage
that the "major modification" fee will be based upon): 43.00
Does the modification involve acreage outside the previously approved permitted boundary?
Yes X. No F. If yes, indicate the additional acreage to be covered by this
modification: 107.90 . (NOTE: you must complete all of Section F. of this application form
entitled Notification of Adjoining Landowners).
Of this acreage to be added to the permit, will any portion of this acreage be affected (i.e.: disturbed, ground cover removed) by the mining operation? Yes X. No ❑ (If no, a "minor modification" fee
of $ ] 00.00 is required, despite the "undisturbed" aaeage to be added). If yes, indicate the acreage to
be affected within the acreage to be added to the permit (the total acreage to be added to the permit is
the acreage that the "major modification" fee will be based upon):_80 acres for overburden storage
❑ If this is an application for TRANSFER of a mining permit, indicate the mining permit number and
the total (overall) acreage covered y the existing permit.
Mining Permit No.: Total permitted acreage:
SEE THE FEE SCHEDULE AT THE END OF THIS FORM FOR THE PROPER FEE AMOUNT TO BE
PAID FOR THE REQUESTED PERMIT ACTION(S) AND CORRESPONDING ACREAGE NOTED
ABOVE
2. Name of all materials mined: Granite
3. Mining method:
BHydraulic Dredge X Front-end Loader & Truck X Shovel & Truck
Dragline & Truck ❑ Self -loading Scraper
Other (explain):
4. a. Expected maximum depth of mine (feet) _
Depth is relative to what benchmark? (e.g.,
Nahrcal ormind level FT = V19' ahnve c
2
mean sea

APPLICATION FOR A MINING PERMIT
b. Expected average depth of mine (feet)
5. Has any area(s) at this site been mined in the past? Yes X No ❑
If yes, when and by whom was this activity conducted? 1988, Nello Teer, Benchmark Carolina
Aggregates, Hanson Aggregates Southeast LLC
6. Number of years for which the permit is requested (Life of the Mining Operation or Life of Lease from
Public Entity): Life of the Mining Operation
B. MAPS
Clearly mark and label the location of your mining operation on six 6 copies of a 7.5-minute quadrangle
and a county highway map. These maps, in addition to six (6) copies of all mine maps and reclamation
maps, must be submitted with each permit application.
7.5-minute quadrangles may be obtained from the N.C. Geological Survey:
Mailing Address:
1612 Mail Service Center OR
Raleigh, North Carolina 27699-1612
[phone]
www.geology.enr.state.nc.us/
Physical Address:
512 North Salisbury Street, 5te Floor
Raleigh, North Carolina 27604
County highway maps may be obtained from the N.C. Department of Transportation:
North Carolina Department of Transportation — Geographic Information Systems (GIS)
Mailing Address:
NCDOT GIS Unit
1587 Mail Service Center
Raleigh, North Carolina 27699-1587
Physical Address:
NCDOT GIS Unit
3401 Carl Sandburg Court
Raleigh, North Carolina 27610
[phone]
www.ncdot.org/it/gisContact/default.htmi
2. Mine maps must be accurate and appropriately scaled drawings, aerial photographs or enlarged
topographic maps of the entire mine site. All aspects of the mine site must be clearly labeled on the
maps along with their corresponding (approximate) acreage. As a reminder, mining permits can
only be issued for up to 10 years; thus, all mine and reclamation maps must only denote those
activities that are intended to be conducted during the life of the mining permit. All maps must be
of a scale sufficient (see minimum requirements listed below) to clearly illustrate the following, at a
minimum:
a. Property lines of the tract or tracts of land on which the proposed mining activity is to be located
including easements and rights -of -way.
b. Existing or proposed permit boundaries.
c. Initial and ultimate limits of clearing and grading.
d. Outline and width of all buffer zones (both undisturbed and unexcavated).
e. Outline and acreage of all pits/excavations.
f. Outline and acreage of all stockpile areas.
g. Outline and acreage of all temporary and/or permanent overburden disposal areas.
h. Location and acreage of all processing plants (processing plants may be described as to location and
distance from mine if sufficiently far removed).
i. Locations and names of all streams, rivers and lakes.
j. Outline and acreage of all settling and/or processing wastewater ponds.
k. Location and acreage of all planned and existing access roads and on -site haul roads.
1. Location of planned and existing on -site buildings.
in. Location and dimensions of all proposed sediment and erosion control measures.
n. Location of 100-year floodplain limits and wetland boundaries.
3

APPLICATION FOR A MINING PERMIT
o. Names of owners of record, both public and private, of all tracts of land that are adjoining the mining
permit boundary; if an adjoining tract is owned or leased by the applicant or is owned by the lessor
of the mine tract, names of owners of record of tracts adjoining these tracts, that are within 1,000 feet
of the mining permit boundary, must be provided on the mine map.p. Names of owners of
record, both public and private, of all tracts of land that are adjoining the mining permit boundary
which lie directly across and are contiguous to any highway, creek, stream, river, or other
watercourse, railroad track, or utility or other public right-of-way. If an adjoining tract is owned or
leased by the applicant or is owned by the lessor of the mine tract, names of owners of record of
tracts adjoining these tracts, that are within 1,000 feet of the mining permit boundary, must be
provided on the mine map(s). NOTE: "Highway" means a road that has four lanes of travel or less
and is not designated as an Interstate Highway.
q. Map legend:
1. Name of applicant
2. Name of mine
3. North arrow
4. County
5. Scale
6. Symbols used and corresponding names
7. Date prepared and revised
8. Name and title of person preparing map
Map scales should meet the following guidelines:
PERMITTED ACREAGE
MAP SCALE
0-49 Acres
1 inch = 50 feet
50-199 Acres
1 inch =100 feet
200+ Acres
1 inch = 200 feet
(NOTE: Smaller scaled maps may be acceptable if they clearly illustrate the above items)

APPLICATION FOR A MINING PERMIT
A table/chart must be provided on the mine map that clearly lists the approximate acreage of tailings/sediment
ponds, stockpiles, watepiles, processing arealhaul roads, mine excavation and any other major aspect of the
mining operation that is proposed to be affected/disturbed during the life of the mining permit. A table/chart
similar to the following will be acceptable:
CATEGORY
Permitted to be Affected
PERMITTED &
AFFECTED
ACREAGE
2016
Modification
2021
Modification
Total
Tailings/Sediment Ponds
32.8
-4.0
32.4
Stockpiles
34.3
17.5
51.8
Wastepiles
26.0
64.1
90.1
Processing Area/Haul Roads
17.2
0.8
18.0
Mine Excavation
56.3
42.6
99.4
Other Areas Permitted for
Disturbance: Asphalt Plant, etc.
11.5
0.0
11.5
Total Acres to be Affected
178.6
124.6
303.1
Other: Buffers, Wetlands, etc.
21.6
69.4
91.1
Total Mine Permitted
286.32
107.90
394.22
NOTE:
IN ADDITION TO THE ABOVE, THE MAPS MUST ALSO INCLUDE ANY SITE -SPECIFIC
INFORMATION THAT IS PROVIDED IN THE ANSWERS TO THE FOLLOWING QUESTIONS IN
THIS APPLICATION FORM (PLEASE NOTE THE ITALICIZED QUESTIONS/STATEMENTS
THROUGHOUT THE FORM). THIS APPLICATION WILL NOT BE CONSIDERED COMPLETE
WITHOUT ALL RELEVANT ITEMS BEING ADEQUATELY ADDRESSED ON THE MINE MAPS.

APPLICATION FOR A MINING PERMIT
C. PROTECTION OF NATURAL RESOURCES
Describe in detail the sequence of events for the development and operation ofthe mine and reference the
sequence to the mine map(s). Attach additional sheets as needed.
The pit is developed in the normal fashion for a mature granite operation. Areas adjacent to the existing
pit are stripped to rock by dirt haulers or our contractors. This disturbed area is made to drain back to the
pit or to approved erosion control structures. The sequence of existing pit, stripped areas and future pit
areas is shown on the submitted Mine Map.
For this modification, Hanson plans to expand its active pit limits to the southwest. At first, the expansion
will only involve enough area to widen the existing one lane haul road to a wider one lane with a
conveyor line or a two-lane haul road into the pit. In the future, to expand the pit into the southwest
comer of the property, both Retention Ponds #2 and #3 will be taken out and wastewater re-routed
through a single proposed Retention Pond #4, and then, routed around the proposed pit and discharged
out the existing NPDES -001 discharge outfall.
Also, for this modification, Hanson has acquired properties north of the existing permitted quarry mainly
for the purpose of constructing berms and wastepiles followed by stabilization. Sediment basins and other
erosion control measures have been designed for the construction of these berms and are shown on the
attached mine maps. Calculations have been included with the mine modification application.
2. Describe specific erosion control measures to be installed prior to land disturbing activities and during
mining to prevent offsite sedimentation (include specific plansforsediment and erosion control for mine
excavation(s), waste piles, access/mine roads and process areas), and give a detailed sequence of
installation and schedule for maintenance of the measures. Locate and label all sediment and erosion
control measures on the mine maps) and provide typical cross-sections/construction details of each
measure. Engineering designs and calculations are required to justify the adequacy of any proposed
measures.
Erosion control measures are noted in the attached Mine Map. These structures are all designed according
to the specifications shown in the Surface Mining Manual distributed by the Land Quality Section.
Details for all existing structures have been submitted and approved through past submittals. Any new
erosion control structures as part of this renewal are detailed in the supporting documents
3. a. Will the operation involve washing the material mined, recycling process water, or other waste water
handling? Yes X No ❑. If yes, briefly describe all such processes including any chemicals to be used.
The crushed stone production process requires water for washing the sized stone products at the wash
screen to remove dust and fines for the eventual use in asphalt and ready mix concrete. The water is
recycled through a closed circuit process water settling pond system. Wash water from the plant is
collected and delivered to one of two primary ponds, where most of the fines are removed by simply
settling out of suspension. These ponds operate in sequence, with one being out of service at any one time
for dipping out of the collected fines using a drag line or long reach excavator. The water then flows to
the secondary pond where settling of additional finer particles takes place. The secondary pond also
serves as a fresh water pond, and the clean water is pumped back to the plant for re -use in the stone
washing process. Due to loss to evaporation from the ponds and loss into the stone products, the water
balance is periodically restored by supplementing with groundwater pumped from the quarry as part of
the dewatering process.
Water is also used for dust control at the facility. Water is used at the processing plants by introduction
through sprays at crushers and at conveyor transfer points to control dust emissions. It is also used in the

APPLICATION FOR A MINING PERMIT
water truck to control dust emanating from haul roads, stockpiles, and the shot rock pile in the pit. Water
used in dust suppression is usually pulled either from the quarry dewatering or from the secondary
settling/fresh water pond.
At the present time, no chemicals are used in any of these processes; however, there are times it is
necessary to use DWQ approved flocculants in the recycle system to help achieve a cleaner source of
water for the plant washing and dust control. It may also become necessary to use chemicals such as
calcium chloride or organic surfactants on the haul roads and crusting agents on the stone product
stockpiles.
b. Will the operation involve discharging fresh or waste water from the mine or plant as a point discharge to
the waters of the State? Yes X No ❑. Ifyes, briefly describe the nature of the discharge and locate
all proposed discharge points (along with their method of stabilization) on your mine map(s).
We currently operate under the NPDES COC No. NCG020087 General Permit that covers the discharge
of excess groundwater and stormwater from the quarry dewatering process, as well as any excess water
from our closed circuit settling pond system. The discharge water passes through a separate settling pond
prior to being discharged into intermittent conveyances reaching Jim Branch Creek. The NPDES Permit
also covers stormwater from the mine sites through multiple point source discharge points.
c. Will any part of the proposed mine excavation(s) extend below the water table? Yes X NoEl.
If yes, do you intend to dewater the excavation(s)? Yes X No ❑.
If yes, what impact, if any, will mine dewatering have on neighboring wells? Estimated withdrawal rate
in gallons per day: 2020 average was recorded as 420,000 alg s/day. Locate all existing wells on the
mine map(s) that lie within 500 feet of the proposed excavation area. Provide data to support any
conclusions or statements made, including any monitoring well data, well construction data and current
water withdrawal rates. Indicate whether the proposed mine locale is served by a public water system
or private wells.
Granite mines do not typically cause a problem with wells on adjacent properties. This site does not have
a history of such problems. The amount of groundwater contained in the pit discharge is unknown. A
large amount of water discharged is stormwater collected in the pit sump. No wells are located within
500 feet of the existing excavation area, and there are no wells located within 500 feet of the proposed
southwest pit expansion. Dwellings around the quarry are served by water supply wells or public water
supply.
Removal of the overburden has very little effect on shallow wells in the area since the pits, for the most
part, sit on a topographic high and very little recharge area for shallow wells will be disturbed. The
overburden materials in the pit areas are silts, clays, and sand which inhibit groundwater migration.
No impact to wells within 500 feet of the quarries have been reported.
d. If you answered yes to any of the above questions, provide evidence that you have applied for or
obtained the appropriate water quality permit(s) (i.e., non -discharge, NPDES, Stormwater, etc.) from the
Stormwater Program. In addition, the applicant is required to register water use with the Division of
Water Resources, Ground Water Management Branch, if the operation withdraws more than 10,000
gallons per day and needs a capacity use permit from the Division of Water Resources, Ground Water
Management Branch, if the operation lies in a capacity use area and withdraws more than 100,000
gallons per day.
The Holly Springs Quarry operates under NPDES COC No. NCG020087 General Permit. Water
withdrawals are reported annually by April I" to the Division of Water Resources under Facility ID No.
0340-0010.
4. a. Will the operation involve crushing or any other air contaminant emissions? Yes X NoEl.
If yes, indicate evidence that you have applied for or obtained an air quality permit issued by the
Division of Air Quality or local governing body.

APPLICATION FOR A MINING PERMIT
NC Air Permit No. 06313R 16, issued by NCDENR DAQ is in place for quarrying. A complete system
of water sprays and/or water carry-over strategies are in place for all crushers and conveyor transfer
points to control particulate emissions from these sources.
b. How will dust from stockpiles, haul roads, etc., be controlled?
A water truck is used to wet the haul roads and stockpiles as needed to control fugitive emissions from
these sources.
a. A buffer will be required between any mining activity and any mining permit boundary or right-of-
way. It may be an unexcavated buffer (no excavation, but roadways, berms and erosion &
sedimentation control measures may be installed within it), an undisturbed buffer (no disturbance
within the buffer whatsoever), or a combination of the two, depending upon the site conditions. Note
that all buffers must be located within the mining permit boundaries.
How wide a buffer will be maintained between any mining activity and any mining permit boundary or
right-of-way at this site? A minimum buffer of 25 feet is recommended, although a wider buffer may
be needed depending on site conditions. Show all buffer locations and widths on the mine map(s).
It is anticipated that a minimum 50 foot undisturbed buffer will be maintained between any mining
activity and existing property line or highway right of way. An additional 50 foot unexcavated buffer
will be maintained and may include visual screening via visual berm or tree plantings. Buffer locations
and widths can be viewed on the attached mine maps.
The buffer locations and widths are shown on the Mine Map and Details Map
b. A minimum 50 foot wide undisturbed buffer will be required between any land disturbing activities
within the mining permit boundaries and any natural watercourses and wetlands unless smaller
undisturbed buffers can be justified. Depending on site conditions, a buffer wider than 50 feet maybe
needed.
How wide an undisturbed buffer will be maintained between any land disturbing activities within the
mining permit boundaries and any natural watercourses and wetlands at this site? Show all buffer
locations and widths on the mine map(s).
A minimum 50-11 undisturbed buffer will be maintained between any land disturbing activities and any
natural watercourses and wetlands on this site. The attached plans have been previously approved and
show specific details relevant to buffers at each location.
6. a. Describe methods to prevent landslide or slope instability adjacent to adjoining permit boundaries
during mining. Minimum 2 horizontal to 1 vertical slopes or flatter for clayey material and minimum 3
horizontal to 1 vertical slopes or flatter for sandy material are generally required, unless technical
justification can be provided to allow steeper slopes.
To prevent landslides and/or slope failure adjacent to adjoining properties, cut slopes will be graded no
steeper than 1-1/2 to 1, and fill slopes will be graded no steeper than 2:1, and proper compaction
procedures will be utilized on fill slopes. All slopes will be stabilized by seeding as soon as possible
after grading has been completed. Necessary erosion controls will be used to prevent slope failure by
concentrated stormwater runoff. Excavation or fill will not generally occur within 100' or 50'
respectively of any adjoining property boundary or right of way except for the installation of visual
screen berms.
For this submittal, plans have been included for the installation of visual screen berms and overburden
piles on the recently acquired Powell and Kinney tracts.
Regarding the southwest pit expansion, perimeter visual screening berms were installed more than 30
years ago along Cass Holt Road, and the trees are fully grown, vegetation is well established, and the
berms are stable.
0

APPLICATION FOR A MINING PERMIT
b. Provide a cross-section on the mine map(s) for all fill slopes (berms, wastepiles, overburden disposal
areas, etc.), clearly indicating the intended side slope gradient, installation of any benches and/or
slope drains (with supporting design information) if needed, and the method of final stabilization.
See attached previously approved mine plans for generalized locations and specific details.
For this submittal, for the newly acquired properties to the north, cross sections have been included for
the planned perimeter visual screening berms and proposed overburden piles with diversion berms
directing run-off to corresponding sediment basins.
Cross sections AA and BB been revised to reflect the southwestern pit expansion. See X-2 Mine Map.
c. In excavation(s) of unconsolidated (non -rock) materials, specify the angle of all cut slopes including
specifications for benching and sloping. Cross -sections for all cut slopes must be provided on the
mine map(s).
The maximum slope within the pit excavation will be 1-1/2:1 in unconsolidated overburden interface.
See attached drawings as well as previously approved mine plans for detailed sections.
d. In hardrock excavations, specify proposed bench widths and heights in feet. Provide cross -sections
of the mine excavation clearly noting the angles of the cut slopes, widths of all safety benches and
mine benches, and the expected maximum depth of the excavation.
At the Holly Springs Quarry, all benches are mined on a % to 1 slope with bench heights of 40 to 45
feet and catch benching widths of at least 20 feet. See attached drawings as well as previously approved
plans for detail sections.
7. Describe other methods to be taken during mining to prevent physical hazard to any neighboring
dwelling house, public road, public, commercial or industrial building from any mine excavation.
Locate all such structures on the mine map if they are within 300 feet of any proposed excavation.
Hanson has always used the most modem and up-to-date mining methods in existence to insure the
safety of its employees and neighbors. Sufficient buffers and proper berm construction are left to
minimize the impact of excavations on adjoining properties and structures.
8. Describe what kind of barricade will be used to prevent inadvertent public access along any high
wall area and when it will be implemented. Vegetated earthen berms, appropriate fencing and adequate
boulder barriers may be acceptable high wall barricades. A construction detail/cross-section and
location of each type of barricade to be used must be indicated on the mine map(s).
Sufficient buffers and proper berm construction ensure minimum impact to adjoining property owners.
All quarry shots are designed to prevent excessive vibrations. Additionally, during each shot event, a
seismograph recording will be taken from the closest off -site occupied structure, if access is allowed, in
relation to the shot location. Depending upon production requirements, the event occurs one to three
times a week. Structures within 300 feet are noted on the mine map.
9. Are acid producing minerals or soils present? Yes ❑ No X.
If yes, how will acid water pollution from the excavation, stockpiles and waste areas be controlled?
Mine dewatering analytical testing has shown no signs of acid water pollution.
10. a. Describe specific plans (including a schedule of implementation) for screening the operation from public
view such as maintaining or planting trees, bushes or other vegetation, building berms or other measures.
Show the location of all visual screening on the mine map(s) and provide cross -sections through all
proposed berms or proposed spacing, sizes and species for tree plantings.
Existing trees, terrain and berms effectively screen our operations from nearby roads and homes.
Trees and/or vegetation have been planted on the berms and in such areas as to promote future
long-term screening and soil stability.
0

APPLICATION FOR A MINING PERMIT
b. Could the operation have a significantly adverse effect on the purposes of a publicly owned park, forest
or recreation area? If so, how will such effects (i.e., noise, visibility, etc.) be mitigated?
There are no publicly owned parks, forest or recreation areas adjacent to the quarry mine excavation area
(the pit); however, as shown on the map, the Trinity Soccer Academy owns and operated a soccer facility
west of and adjacent to the newly acquired Kenney tract. The acquired Powell and Kenney tracts were
rezoned in 2019 to construct visual screening berms, overburden piles, corresponding sediment basins, and
storage of miscellaneous construction equipment; and no mining excavation is allowed. Screening berms
and overburden piles will be stabilized following their construction. There should be no issues with noise,
visibility, etc.
There is also a tract adjacent to the acquired Powell and Kenney tracts that is owned by the Town of Holly
Springs and a tract owned by the Wake County Board of Education, but there is no disturbance on either
property to date.
11. Will explosives be used? Yes X No ❑.
If yes, specify the types of explosive(s) and describe what precaution(s) will be used to prevent physical
hazard to persons or neighboring property from flying rocks or excessive air blasts or ground vibrations.
Depending on the mine's location to nearby structures, more detailed technical information may be
required on the blasting program (such as a third -party blasting study). Locate the nearest offsite occupied
structures) to the proposed excavation(s) on the mine map and indicate its approximate distance to the
proposed excavation
Ensign Bickford or comparable none] blast initiation system is used to inadvertent blast initiation especially
during possible thunderstorms. An electronic initiation system may be substituted for the nonel system if it
is deemed a better overall system. Weather conditions are monitored continuously before, during, and after
loading of each shot to insure that the shot will not be initiated under adverse weather conditions that might
cause blast emissions to drift in an unacceptable direction or might prevent proper venting of the blast wave
away from adjoining properties. ANFO premixed powder is used in dry holes. A cap -sensitive high
explosive emulsion is used for wet holes and initiation of the ANFO.
Since blasting is an integral part of this operation, each blast is monitored with a seismograph to insure that
peak particle velocities and peak over pressures are within the limits established by local, state, and federal
authorities. Hanson works closely with consultants (often Vibratech) to monitor and review each blast and
seismographic recording. Along with the seismograph results, fragmentation and flyrock conditions are
constantly monitored, and the blasting program, including direction of blasting, hole size and pattern,
stemming, etc. are adjusted as needed to insure best and safest results.
12. Will fuel tanks, solvents, or other chemical reagents be stored on -site? Yes X No ❑.
Ifyes, describe these materials, how they will be stored and method of containment in case ofspill. Indicate
the location(s) of all storage facilities on the mine map(s).
Onsite storage of diesel fuel, gasoline, and various oils and greases is necessary to facilitate the operation of
various equipment needed to mine and process crushed stone aggregates. The bulk storage tanks for diesel
fuel, gasoline, and oils are approved aboveground storage tanks having concrete secondary containment.
Any major spill or leak from these tanks would be contained within the concrete containment structures.
Greases and other oils are stored in aboveground storage tanks and 55-gallon drums and are stored in a
concrete containment structure. Used oil is collected from equipment and picked up for offsite recycling by
properly certified contractors. Empty oil and grease barrels are returned to the supplier or cleaned and placed
into the metal scrap bin for offsite recycling. The Holly Springs facility has a Spill Prevention Control &
Countermeasures (SPCC) Plan that requires monthly inspections of all bulk fuel and lube storage units. All
employees are trained on a regular basis in the proper handling of petroleum products, managing and
cleaning of spills, and proper disposal of rags, absorbent materials, and any contaminated soils.
10

APPLICATION FOR A MINING PERMIT
D. RECLAMATION PLAN
1. Describe your intended plan for the final reclamation and subsequent use of all affected lands and indicate
the sequence and general methods to be used in reclaiming this land. This must include the method of
reclamation of settling ponds and/or sediment control basins and the method of restoration or establishment
of any permanent drainage channels to a condition minimizing erosion, siltation and other pollution. This
information must be illustrated on a reclamation map and must correspond directly with the information
provided on the mine map(s). In addition, design information, including typical cross -sections, of any
permanent channels to be constructed as part of the reclamation plan and the location(s) of all permanent
channels must be indicated on the reclamation map.
The mine excavations will be allowed to fill to a normal level by groundwater and stormwater runoff from
adjoining areas whenever the mining operations are completed. The resulting deep water lake may be used
for recreation, and potentially as a fresh water supply. The plant sites, stockpile areas, and overburden
disposal areas will be graded and seeded with grasses suitable for establishment of grasslands and wildlife
areas. Process and pit water settling ponds will be filled and similarly reclaimed to grasslands unless they are
a part of the overall site drainage and reclamation plan.
See attached reclamation drawings for specific details
2. Is an excavated or impounded body of water to be left as a part of the reclamation? Yes X No ❑.
If yes, illustrate the location of the body(s) of water on the reclamation map and provide a scaled
cross-section(s) through the proposed body(s) of water. The minimum water depth must be at least 4 feet,
measured from the normal low water table elevation, unless information is provided to indicate that a more
shallow water body will be productive and beneficial at this site.
Will the body(s) of water be stocked with fish? Yes ❑ No X.
If yes, specify species.
It is Hanson's intent to convert the quarry into a fresh water lake upon cessation of mining activities. In
addition, the fresh water pond , as shown on the attached drawings, will remain. A large percentage of the
mining area will be left as impounded water. In some areas, overburden will be backfilled to an elevation
several feet above the water table, and seeded according to schedule.
See attached drawings for specific details and cross sections.
3. Describe provisions for safety to persons and to adjoining property in all completed excavations in rock
including what kind of permanent barricade will be left. Acceptable permanent barricades are appropriate
fencing, large boulders placed end -to -end, etc. Construction details and locations of all permanent
barricades must be shown on the reclamation map.
As a safety precaution, a 20-foot wide safety bench will be left at the rock/unconsolidated soil interface. A
permanent fence will be erected around the completed quarries to prevent unauthorized entry, and danger
signs will be posted at regular intervals along the fence to warn folks of the open pits. Large boulders placed
end -to -end may be placed around all excavations in lieu of fencing.
4. Indicate the method(s) of reclamation of overburden, refuse, spoil banks or other such on -site mine waste
areas, including specifications for benching and sloping. Final cross -sections and locations for such areas
must be provided on the reclamation map.
As overburden is placed in designated areas, it is spread and compacted by dozer and haul units. Slopes in
waste areas will be graded 2:1 or flatter and vegetated as soon as possible to prevent erosion. Erosion control
measures and runoff conveyances will be established as the wastepile develops and then maintained
throughout the process until final reclamation is achieved. Drainage on top of the waste areas will be
established to prevent pooling and stagnation of water and to control runoff. Final reclamation of waste areas
will include final top and slope dressing as required followed by seeding in accordance with the attached
revegetation plan. See attached drawings for specific detail.
11

APPLICATION FOR A MINING PERMIT
a. Describe reclamation of processing facilities, stockpile areas, and on -site roadways.
Reclamation in these areas will occur as follows. First, the product stockpiles will be sold down. Then the
processing plants will be dismantled and removed from the site. Any remaining piles, waste piles, and areas
graded for plant layout and operation (including ramps to the primary stations) will be graded 2:1 maximum
slope but generally 3:1 or flatter. Finally, these areas will be scarified and seeded according to the
revegetation plan. Any site access roads not utilized in the end use development plan will be treated in the
same manner.
Any erosion control structures in these areas to be incorporated into the end use development of the site will
be cleaned out and left in good working condition.
b. Will any on -site roadways be left as part of the reclamation? Yes X No Ifyes,
identify such roadways on the reclamation map and provide details on permanent ditch line stabilization.
Main paved roads into the existing stone processing area will remain for access and future development
purposes. The road through the existing plant site to the former plant area will remain and will be graded,
including side drainage ditches, and stabilized with rock.
6. Describe the method of control of contaminants and disposal of scrap metal, junk machinery, cables, or other
such waste products of mining. (Note definition of refuse in The Mining Act of 1971.)
No off -site venerated waste shall be disposed of on the mine site without prior written approval from
the NC Department of Environmental Quality, Division of Energy, Mineral, and Land Resources and
either the Division of Waste Management (DWM) or local governing body. If a disposal permit has
been issued by DWM for the site, a copy of said permit must be attached to this application. All
temporary and permanent refuse disposal areas must be clearly delineated on the mine map(s) and
reclamation map, along with a list of items to be disposed in said areas.
As previously approved, temporary scrap and used equipment storage areas have been developed at this site.
The scrap material and used equipment which accumulate as a result of mining and processing activities are
stored in these areas until sold to an independent recycling contractor.
A scrap bin is maintained on site for disposal by recycling of small metal scrap. Tires are recycled through
the various tire suppliers.
7. Describe your plan for revegetation or other surface treatment of the affected areas. This plan must
include recommendations for year-round seeding, including the time of seeding and the amount and type of
seed, fertilizer, lime and mulch per acre. The recommendations must include general seeding instructions
for both permanent and temporary revegetation. Revegetation utilizing only tree plantings is not
acceptable. Recommendations can be sought from:
a. Authorized representatives of the local Soil and Water Conservation District;
b. Authorized representatives of the NC Forest Service, Department of Agriculture and Consumer
Services;
c. Authorized county representatives of the North Carolina Cooperative Extension Service, specialists
and research faculty with the Colleges of Agriculture and Life Sciences and Forest Resources at
North Carolina State University;
d. North Carolina licensed landscape architects;
e. Private consulting foresters referred by the NC Forest Service, Department of Agriculture and
Consumer Services;
f. N.C. Erosion and Sedimentation Control Planning and Design Manual;
g. N.C. Surface Mining Manual: A Guide for Permitting, Operation and Reclamation;
h. Others as may be approved by the Department.
12

APPLICATION FOR A MINING PERMIT
LIME - RATE OF APPLICATION (tons/acre):
2000 Ib/ac applied in spring. Application rate to be adjusted based on soil sampling results.
FERTILIZER - ANALYSIS AND RATE OF APPLICATION (pounds/acre):
As required use of 10-10-10 at 500lb/acre. Land application of animal waster (chicken litter) used when
available.
SEED - TYPE (S) AND RATE (S) OF APPLICATION INCLUDING YEAR-ROUND SEEDING
SCHEDULE (pounds/acre): [NOTE: Include Legumes]
Final Cover: Sercea Lespedeza (60%) Bermuda (40%) or Sericea or Bermuda depending on area being
planted. (60-80 lb/acre depending on seed type)
Temporary Cover: Small grain or rye in fall/winter at 15- lb/acre. Millet in spring/summer at 200lb/acre.
MULCH - TYPE AND RATE OF APPLICATION (pounds/acre) AND METHOD OF ANCHORING:
Clean straw or hay @ 2 tons/acre
Tack with rapid setting emulsified asphalt at 10 gal./1000 square foot, or other tacking agent approved by
Owner.
OTHER VEGETATIVE COVERS —TYPE (S) AND RATE (S) OF APPLICATION INCLUDING
SEEDING SCHEDULE (pounds/acre, trees/acre, spacing of trees/shrubs, etc):
Revegetation and/or reforestation plan approved by:
Signature _
Print Name
Title
Agency
Date
E. DETERMINATION OF AFFECTED ACREAGE AND BOND
The following bond calculation worksheet is to be used to establish an appropriate bond (based upon a range
of $500 to $5,000 per affected acre) for each permitted mine site based upon the acreage approved by the
Department to be affected during the life of the mining permit. Please insert the approximate acreage, for each
AFFECTED
RECLAMATION
CATEGORY
ACREAGE
COST/ACRE*
Tailings/Sediment Ponds:
Ac.
X
$
/Ac. _
Stockpiles:
Ac.
X
$
/Ac. _
Wastepiles:
Ac.
X
$
/Ac. _
Processing Area/Haul Roads:
Ac.
X
$
/Ac. _
Mine Excavation:
Ac.
X
$
/Ac. _
Other:
Ac.
X
$
/Ac. _
TOTAL AFFECTED AC.:
Ac.
(TOTAL PERMITTED AC.:
Ac.)
13
RECLAMATION
COST

APPLICATION FOR A MINING PERMIT
Temporary & Permanent Sedimentation & Erosion Control Measures:
Divide the TOTAL AFFECTED AC. above into the following two categories: a) affected acres that drain into
proposed/existing excavation and/orb) affected acres that will be graded for positive drainage where measures will
be needed to prevent offsite sedimentation and sedimentation to onsite watercourses and wetlands.
a) Internal Drainage Ac.
b) Positive Drainage
Inflation Factor:
Ac. X $1,500.00 = $
SUBTOTAL COST: I
0.02 X SUBTOTAL COST: $ X Permit Life (1 to 10 years):
INFLATION COST: $
Total Reclamation Braid Cost: $
round down to the nearest $100.00
TOTAL COST = SUBTOTAL COST + INFLATION COST = $
Note: Hanson Aggregates Southeast, LLC has a maximum bond of $1,000,000.00 in place at this
time pursuant to N.C.G.S. 74-54.
14

F. NOTIFICATION OF ADJOINING LANDOWNERS
The "Notice" form, or a facsimile thereof, attached to this application must be sent certified or registered mail
to:
(1)the chief administrative officer of each county and municipality in which any part of the permitted
area is located as indicated on the mine map(s);
(2)all owners of record, both public and private, of all tracts of land that are adjoining the mining permit
boundary; if an adjoining tract is owned or leased by the applicant or is owned by the lessor of the
mine tract, all owners of record of tracts adjoining these tracts must be notified (that are within
1,000 feet of the mining permit boundary) as indicated on the mine map(s); and
(3)all owners of record, both public and private, of all tracts of land that are adjoining the mining permit
boundary which He directly across and is contiguous to any highway; creek, stream, river, or other
watercourse; railroad track; or utility or other public right-of-way; if an adjoining tract is owned
or leased by the applicant or is owned by the lessor of the mine tract, all owners of record of tracts
adjoining these tracts must be notified (that are within 1,000 feet of the mining permit boundary)
as indicated on the mine map(s). "Highway" means a road that has four lanes of travel or less and
is not designated as an Interstate Highway.
The only exception to the above method of giving notice is if another means of notice is approved in advance
by the Director, Division of Land Resources.
A copy of a tax map (or other alternative acceptable to the Department) must be mailed with the completed
"Notice" form (the proposed overall permit boundaries and the names and locations of all owners of
record of lands adjoining said boundaries must be clearly denoted on the tax map).
The "Affidavit of Notification" attached to this application must be completed, notarized and submitted to the
Department, with the remainder of the completed application form, before the application will be considered
complete.
Please see the following notarized affidavit and copy of notification letters sent to the local Town and
County managers and adjacent property owners.

NOTICE
Pursuant to provisions G.S. 74-50(bI) of The Mining Act of 1971, Notice is hereby given that
has applied on July 1, 2021
(Date)
to the Land Quality Section, Division of Land Resources, North Carolina Department of Environment
and Natural Resources, 1612 Mail Service Center, Raleigh, North Carolina 27699-1612, for (check one):
❑ a new surface mining permit,
X a modification of an existing surface mining permit to add land to the permitted area; or
❑ a modification of an existing surface mining permit to add land to the permitted area with no disturbance
in a area proposed. Please note that future modification(s) ma . be submitted by the applicant to
allow disturbance within this area without re -notification of adjoining landowners.
The applicant proposes to mine, stockpile overburden (clay, topsoil, and fines) on 106.3 acres located 4_5
(Mineral, Ore) (Number) (Miles)
southwest of Holly Springs off/near road 6120, 6200, 6212, & 6312 Rex Road
(Direction) (Nearest Town)
in Wake County.
(Number/Name)
*SEE ATTACHED MAP FOR PROPOSED PERMIT BOUNDARIES AND CORRESPONDING
ADJOINING LANDOWNER NAMES AND LOCATIONS*
In accordance with G.S. 74-50(bI), the mine operator is required to make a reasonable effort, satisfactory to the
Department, to notify all owners of record, both public and private, of all tracts of land that are adjoining the mining
permit boundary; if an adjoining tract is owned or leased by the applicant or is owned by the lessor of the mine tract,
all owners of record of tracts adjoining these tracts must be notified (that are within 1,000 feet of the mining permit
boundary). In addition, the mine operator must also notify the chief administrative officer of the county or
municipality in which any part of the permitted area is located. Any person may file written comment(s) to the
Department at the above address within thirty (30) days of the issuance of this Notice or the filing of the application
for a permit, whichever is later. Should the Department determine that a significant public interest exists relative to
G.S. 74-51, a public hearing will be held within 60 days of the end of the 30-day comment period specified above.
A copy of the permit application materials is on file and available for public review during normal business
hours at the above listed address as well as at the appropriate regional office. For information regarding i
on
19) 707-9220.
Randy Har 'n on. Holly Springs Town Manager
(Addressee/Owner of Record's
Name and Address)
128 S Main Street, P.O. Box 8
Holly Springs, NC 27540
[phone]
(Date of Issuance of this Notice/ July 6, 2021
Mailed to Addressee/Owner of Record)
16
contact
Jack Garvev. Hanson Aggregates Southeast LLC
(Name of Applicant: Include Contact Person
& Company Name, if Applicable)
3825 Barrett Drive, Suite 300
Raleigh, NC 27609
[phone]
(Address of Applicant)

/.y h
19,
/j �. - ��� • III �� � �
♦��1.
9�i _ �°a''♦i! Y�•♦d0290'°i°i°i°♦♦i♦�ii°i°i°i°s°i♦*°i°i0
°i'�"°a°i°i°i°i°'Ji°i'P'i°°i°i°'♦°�°idi°i°'♦
6021 Ten Ten Road, Apex,
NC 27539-830S
°� ° !o • ♦�
•° ©�
©® PO C27 ,
�540-0008
WAKE COUNTY BOARD OF
EDUCATION
ENNIS, JOHN 8 lilyi
TRINITY SOCCER ACADEMY
• • • • HANSON AGGREGATES SOUTHEAST, LLC NOR
.:
SOUTH•
HansonHOLLY SPRINGS QUARRY
HOLLY SPRINGS, NC - WAKE COUNTY
HEIDELBERGCEMENTGr..

NOTICE
Pursuant to provisions G.S. 74-50(bl) of The Mining Act of 1971, Notice is hereby given that
has applied on July 1, 2021
(Date)
to the Land Quality Section, Division of Land Resources, North Carolina Department of Environment
and Natural Resources, 1612 Mail Service Center, Raleigh, North Carolina 27699-1612, for (check one):
❑ a new surface mining permit,
X a modification of an existing surface mining permit to add land to the permitted area; or
❑ a modification of an existing surface mining permit to add land to the permitted area with no disturbance
in the area proposed. Please note that future modification(s) may be submitted by the applicant to
allow disturbance within this area without re -notification of adjoining landowners.
The applicant proposes to mine, stockpile overburden (clay, topsoil, and fines) on 106.3 acres located 4_5
(Mineral, Ore) (Number) (Miles)
southwest of Holly Springs off/near road 6120, 6200, 6212, & 6312 Rex Road
(Direction) (Nearest Town)
in Wake County.
(Number/Name)
*SEE ATTACHED MAP FOR PROPOSED PERMIT BOUNDARIES AND CORRESPONDING
ADJOINING LANDOWNER NAMES AND LOCATIONS*
In accordance with G.S. 74-50(bl), the mine operator is required to make a reasonable effort, satisfactory to the
Department, to notify all owners ofrecord, both public and private, of all tracts of land that are adjoining the mining
permit boundary; if an adjoining tract is owned or leased by the applicant or is owned by the lessor of the mine tract,
all owners ofrecord of tracts adjoining these tracts must be notified (that are within 1,000 feet of the mining permit
boundary). In addition the mine operator must also notify the chief administrative officer of the county or
municipality in which any part of the permitted area is located. Any person may file written comment(s) to the
Department at the above address within thirty (30) days of the issuance of this Notice or the filing of the application
for a permit, whichever is later. Should the Department determine that a significant public interest exists relative to
G.S. 74-51, a public hearing will be held within 60 days of the end of the 30-day comment period specified above.
A copy of the permit application materials is on file and available for public review during normal business
hours at the above listed address as well as at the appropriate regional office. For information regarding i
on me mining
at [phone].
David Ellis. Wake Countv. NC Countv Manager
(Addressee/Owner of Record's
Name and Address)
301 S. McDowell St, 4'" Floor
Raleigh, NC 27601
[phone]
(Date of Issuance of this Notice/ July 6, 2021
Mailed to Addressee/Owner of Record)
17
review
Jack Garvev. Hanson Aggregates Southeast LLC
(Name of Applicant: Include Contact Person
& Company Name, if Applicable)
3825 Barrett Drive, Suite 300
Raleigh, NC 27609
[phone]
(Address of Applicant)

18)
VON
wi
. , ,A -
Z',K
PIanX
Owner
Owner Address
1
IUOPOULOS, EMMIE
6504CASSHOLTRD,HOLLY
�`\
IUOPOULOS, IOHN
SPRINGS,NC27540-9771
2
ROBERTSON, SAMUELJOSEPH
6512 REX RD, HOLLY
ROBERTSON, SHAN AN
SPRINGS, NC 27540-9808
3
TYLER,JOHN D TYLER,
6021 Ten Ten Road, Apex,
^1\
GRAPHIC SCALE... '
THERESAL
NC 27539-8305
4
CHURCHILL, STEPHEN
65M REX RD, HOLLY
CHURCHILL, TANYA S
SPRINGS, NC 27S40MM
TOWN ATTORNEYS OFFICE
•
_ 1
5
TOWN OF HOLLY SPRINGS
PO BOX 8, HOLLY SPRINGS,
' -
INC 27540-OWS
6
POWELL, LA RUE
7036 Rouse Road, Holly
..
S rings, NC 27540-9S39
7
WAKE COUNTY BOARD OF
111 CORNING RD STE 100,
-
- -
EDUCATION
CARY, NC 27518-9299
8
ENNIS, JOHNB
6123 REKRD, HOLLY
SPRINGS, NC 27540-6438
9
TRINITY SOCCER ACADEMY
10528 MARION STONE WAY,
RALEIGH NC 27614-9891
TAX DEPT- DEC41BS50 S.
10
DUKE ENERGY PROGRESS INC
Tryon Street, Charlotte, NC
28202-4200
HOLLY SPRINGS QUARRY NOTIFICATION MAP
OCTOBER2019
SCALE-1^= 1000-
HANSON AGGREGATES SOUTHEAST, LLC
1 �i
SOUTH REGION
`Hanson
HOLLY SPRINGS QUARRY
T
HOLLY SPRINGS, NC • WAKE COUNTY
HEIDELISERGCEMENTGrOup

APPLICATION FOR A MINING PERMIT
Mailed to Addressee/Owner of Record AFFIDAVIT OF NOTIFICATION
I, Jack Garvey , an applicant, or an agent, or employee of an
applicant, for a new Mining Permit, or a modification of an existing Mining Permit to add land to the permitted
area, from the N.C. Department of Environment and Natural Resources, being first duly sworn, do hereby attest
that the following are all known owners of record, both public and private, of all tracts of land that are adjoining
the mining permit boundary (including, where an adjoining tract is owned or leased by the applicant or is owned
by the lessor of the mine tract, all owners of record of tracts adjoining these tracts, that are within 1,000 feet of
the mining permit boundary) and that notice of the pending application has been caused to be mailed, by certified
or registered mail, return receipt requested, to said owners of record at their addresses shown below, such notice
being given on a form provided by the Department:
(Adjoining Landowner Name) Notification Map #
Emmie Iliopoulos & John IliWoulos
Samuel Robertson Joseph Robertson. & Shan Jin
John D. Tyler & Theresa L. Tyler
Stephen Churchill & Tanya S. Churchill
Town of Holly Springs
La Rue Powell
Wake County Board of Education
John B. Ennis
Trinity Soccer Academy
Duke Energy Progress Inc
Mailing Address
1
6504 Cass Holt Road, Holly Springs, NC 27540-9771
2
6512 Rex Road, Holly Shrines, NC 27540-8808
3
6021 Ten Ten Road, Apex, NC 27539-8305
4
6500 Rex Road, Holly Snrings, NC 27540-8808
5
P.O. Box 8. Holly Springs, NC 27540-0008
6
7036 Rouse Road, Holly Springs, NC 27540-9539
7
111 Corning Road, Ste 100, Cary, NC 27518-9299
8
6113 Rex Road, Holly Springs. NC 27540-6438
9
10628 Marion Stone Way, Raleigh, NC 27614-9891
10
550 S. Tryon Street, Charlotte, NC 28202-4200
(Attach additional list if necessary)
I do also attest that the following individuals are the chief administrative officers of the county and/or municipality
in which any part of the permitted area is located and that notice of the pending application has been caused to be
mailed, by certified or registered mail, return receipt requested, to said office at the following address:
(Chief Administrative Officer Name) (Address)
[i.e.: City Manager, County Manager, Mayor, etc.]
Randy Harrington, Holly Springs Town Manager 128 S Main St, P.O. Box 8, Holly Springs, NC 27540-0008
David Ellis, Wake County, NC County Manager 301 S. McDowell St, 4ei Floor, Raleigh, NC 27601
The above attestation was made by me while under oath to provide proof satisfactory to the Department that a
reasonable effort has been made to notify all known owners of record, both public and private, of all tracts of land
that are adjoining the mining permit boundary (including, where an adjoining tract is owned or leased by the
applicant or is owned by the lessor of the mine tract, all owners of record of tracts adjoining these tracts, that are
within 1,000 feet of the mining permit boundary) and the chief administrative officer of the county or municipality
in which any part of the permitted area is located in compliance with N.C.G.S. 74-50(bl) and 15A NCAC 5B
.0004(d). I understand that it is the responsibility of the applicant to retain the receipts of mailing showing that
the above notices were caused to be mailed and to provide them to the Department upon request.
7 J9 j- 0 2
SignA& of Applicant or AgAit Date
If person executing Affidavit is an agent or employee of an applicant, provide the following information:
Name of applicant: Jack Garvey
Title of person executing Affidavit Environmental Manager

APPLICATION FOR A MINING PERMIT
I, 7o4in m 4 S - t-+k 4e-41' a Notary Public of the County of
State of North Carolina, do hereby certify that J�- C �Cxy V -e
appeared before me this day and under oath acknowledged that the above Affidavit was made by him/her.
Witness my hand and notarial seal, this 4*0� day of 20_L.
Notary:S m Commission expires: to - �(9 "

APPLICATION FOR A MINING PERMIT
G. LAND ENTRY AGREEMENT
We hereby grant to the Department or its appointed representatives the right of entry and travel upon our lands
or operation during regular business hours for the purpose of making necessary field inspections or investigations as
may be reasonably required in the administration of the Mining Act of 1971 pursuant to G.S. 74-56.
We further grant to the Department or its appointed representatives the right to make whatever entries on the
land as may be reasonably necessary and to take whatever actions as may be reasonably necessary in order to carry
out reclamation which the operator has failed to complete in the event a bond forfeiture is ordered pursuant to G.S.
74-59.
LANDOWNER:
Signature:
Print Name: Daren McMorris
(Title, if applicable)
Company: Hanson Aggregates Southeast LLC
(If applicable)
Address: 3825 Barrett Drive, Suite 300
Raleigh, NC 27609
Telephone: [phone]
Date Signed: July 1, 2021
APPLICANT:
Signature:*
Print Name: Daren McMorris
Title: NC Operations Manager
Company: Hanson Aggregates Southeast LLC
Mine Name: Hanson Aggregates — Holly prings Quarry
Telephone: [phone]
Date Signed: July 1, 2021
*Signature must be the same as the individual who signed Page 1 of this application.
One original and five (5) copies of the completed application, six (6) copies of all location maps, mine maps
and reclamation maps, and the appropriate processing fee (see next page for fee schedule) in the forma check
or money order payable to the North Carolina Department of Environmental Quality must be sent to the
Raleigh Central Office at the address listed on the front cover of this application form.
Inquiries regarding the status of the review of this application should be directed to the Mining Program staff at
[phone].
31

APPLICATION FOR A MINING PERMIT
MINING FEE SCHEDULE
Hanson Aggregates — Holly Springs Quarry 2021 Mine Permit Modification Application
A nonrefundable permit application processing fee when filing for a new mining permit, a major permit modification or a renewal
permit is required as follows:
0-25 acres 26+acres
New Permit Applications $3,750.00 $5,000.00
Permit Modifications $750.00 $1,000.00
Permit Renewals $750.00 $1,000.00
Transfers/MinorModifications* $100.00 $100.00
- A nonrefundable $100.00 permit application processing fee is required for minor permit modifications. Minor permit modifications include ownership transfers,
name changes, bond substitutions and permit renewals where the mine is inactive and fully stabilized. A minor permit modification also includes lands added to a
permitted area, outside of the minimum permit buffer zone requirements, where no plans for mining related disturbance of the added lands have been approved.
All other changes are considered major permit modifications.
Acres for new permits and renewal permits means the total acreage at the site. Acres for major modification of permits means that area of land affected by the
modification within the permitted mine area, or any additional land that is to be disturbed and added to an existing permitted area, or both.
Make checks payable to: NC Dept. of Environmental Quality
Division of Energy, Mineral, and Land Resources
1620 Mail Service Center
Raleigh, NC 27699-1612
21