AQ_F_0400058_20220429_PRMT_Permit_R04

ROY COOPER
Governor 1!
ELIZABETH S.BISER
Secretary a2
MICHAEL A.ABRACZINSKAS NORTH CAROLINA
Director Environmental Quality
April 29, 2022
Mr. Chris Harrington
Director of EH&S
Edwards Wood Products, Inc. -Peachland
2215 Old Lawyers Road
Marshville,NC 28103
Subject: Air Permit No. 10146R04
Edwards Wood Products,Inc. -Peachland
Peachland,Anson County,North Carolina
Permit Class: Small
Facility ID#0400058
Dear Mr. Harrington:
In accordance with your completed application received March 28,2022, we are forwarding
herewith Permit No. 10146R04 to Edwards Wood Products, Inc. - Peachland, Peachland,Anson
County,North Carolina for the construction and operation of air emissions sources or air cleaning
devices and appurtenances. Additionally, any emissions activities determined from your air permit
application as meeting the exemption requirements contained in 15A NCAC 2Q .0102 have been
listed for information purposes as an"ATTACHMENT" to the enclosed air permit. Please note the
records retention requirements are contained in General Condition 2 of the General Conditions and
Limitations.
The Permittee shall only operate either the Natural gas-fired boiler(16.739 mmBtu/hr
maximum heat input) (ID No. ES-5) or the Stoker type wood-fired boiler(10.54 mmBtu/hr
maximum heat input (300 BHP)) (ID No. ES-1),not both simultaneously,to ensure emissions
do not exceed Toxic Permit Emission Rates (TPERs).
If any parts,requirements, or limitations contained in this permit are unacceptable to you,
you have the right to request a formal adjudicatory hearing within 30 days following receipt of this
permit, identifying the specific issues to be contested. Such a request will stay the effectiveness of
the entire permit. This hearing request must be in the form of a written petition, conforming to G.S.
150B-23 of the North Carolina General Statutes,and filed with the Office of Administrative
Hearings, 6714 Mail Service Center,Raleigh,NC 27699-6714. The form for requesting a formal
adjudicatory hearing may be obtained upon request from the Office of Administrative Hearings.
Unless a request for a hearing is made pursuant to G.S. 15013-23,this air permit shall be final and
binding.
North Carolina Department of Environmental Quality I Division of Air Quality
e:�'1-_'_' Q_E Fayetteville Regional Office 1 225 Green Street,Suite 714 1 Fayetteville,NC 28301-5094
ueoartmaret at enren�ma nuar /M��''� 910.433.3300 T 1 910.485.7467 F

Chris Harrington
April 29, 2022
Page 2
You may request modification of your air permit through informal means pursuant to G.S.
15013-22. This request must be submitted in writing to the Director and must identify the specific
provisions or issues for which the modification is sought. Please note that the permit will become
final and binding regardless of a request for informal modification unless a request for a hearing is
also made under G.S. 15013-23.
Unless exempted by a condition of this permit or the regulations, construction of new
air pollution sources or air cleaning devices, or modifications to the sources or air cleaning
devices described in this permit must be covered under a permit issued by the Division of Air
Quality prior to construction. Failure to do so is a violation of G.S. 143-215.108 and may
subject the Permittee to civil or criminal penalties as described in G.S. 143-215.114A and 143-
215.114B.
This permit shall be effective from April 29, 2022 until May 31, 2024, is nontransferable to
future owners and operators, and shall be subject to the conditions and limitations as specified
therein.
Changes have been made to the permit stipulations. The Permittee is responsible for
carefully reading the entire permit and evaluating the requirements of each permit
stipulation. The Permittee shall comply with all terms, conditions, requirements, limitations
and restrictions set forth in this permit. Noncompliance with any permit condition is grounds
for enforcement action, for permit termination, revocation and reissuance, or modification, or
for denial of a permit renewal application. Should you have any questions concerning this matter,
please contact Evangelyn Lowery-Jacobs at 910-433-3300.
Sincerely,
e
C all%
Heather Carter, Regional Supervisor
Division of Air Quality,NC DEQ
ELJ
Enclosures
c: Fayetteville Regional Office

NORTH CAROLINA ENVIRONMENTAL MANAGEMENT COMMISSION
DEPARTMENT OF ENVIRONMENTAL QUALITY
DIVISION OF AIR QUALITY
AIR PERMIT NO. 101461104
Issue Date: April 29,2022 Effective Date: April 29, 2022
Expiration Date: May 31, 2024 Replaces Permit: 10146R03
To construct and operate air emission source(s) and/or air cleaning device(s), and for the
discharge of the associated air contaminants into the atmosphere in accordance with the provisions
of Article 21B of Chapter 143, General Statutes of North Carolina(NCGS) as amended, and other
applicable Laws,Rules and Regulations,
a
Edwards Wood Products,Inc. -Peachland
160 Pulpwood Yard Road
Peachland,Anson County,North Carolina
Permit Class: Small
Facility ID#0400058
(the Permittee) is hereby authorized to construct and operate the air emissions sources and/or air
cleaning devices and appurtenances described below:
mi n Source ­j Control System
Description e x Systeu ID Description
�. E
_ _
Stoker rype wood-fired Boiler
ES-1 (10.54 mmBtu/hr CD-MCI Multiclone with 8
(NSPS,NESHAP) 1 nine inch diameter tubes
i maximum heat input(300 BHP))
ES-2 Four(4)steam-heated lumber drying kilns
(62,000 board feet capacity each)
----ES-3 Two(2)steam-heated lumber drying kilns N/A
j (28,000 board feet capacity each)
ES-5 Natural gas-fired boiler
(NSPS) (16.739 mmBtu/hr maximum heat input)
in accordance with the completed application 0400058.22A received March 28, 2022 including any
plans, specifications,previous applications, and other supporting data, all of which are filed with the
Department of Environmental Quality, Division of Air Quality (DAQ) and are incorporated as part
of this permit.

Permit No. 10146R04
Page 2
This permit is subject to the following specified conditions and limitations including any
TESTING, REPORTING, OR MONITORING REQUIREMENTS:
A. SPECIFIC CONDITIONS AND LIMITATIONS
1. Any air emission sources or control devices authorized to construct and operate above must
be operated and maintained in accordance with the provisions contained herein. The
Permittee shall comply with applicable Environmental Management Commission
Regulations, including Title 15A North Carolina Administrative Code (NCAC), Subchapter
2D .0202, 2D .0504, 2D .0515, 2D .0516, 2D .0521, 2D .0524 (40 CFR 60, Subpart Dc), 2D
.0535, 2D .0540,2D .1100, 2D .1111 (40 CFR 63, Subpart JJJJJJ), 2D .1806 and 2Q .0711.
2. PERMIT RENEWAL AND EMISSION INVENTORY REQUIREMENT - The Permittee,
at least 90 days prior to the expiration date of this permit, shall request permit renewal by
letter in accordance with 15A NCAC 2Q .0304(d) and(f). Pursuant to 15A NCAC 2Q
.0203(i), no permit application fee is required for renewal of an existing air permit(without
a modification request). The renewal request(with application Form A) should be submitted
to the Regional Supervisor, DAQ. Also, at least 90 days prior to the expiration date of this
permit,the Permittee shall submit the air pollution emission inventory report(with
Certification Sheet) in accordance with 15A NCAC 2D .0202,pursuant to N.C. General
Statute 143 215.65. The report shall be submitted to the Regional Supervisor, DAQ and shall
document air pollutants emitted for the 2022 calendar year.
3. PARTICULATE CONTROL REQUIREMENT - As required by 15A NCAC 2D .0504
"Particulates from Wood Burning Indirect Heat Exchangers," particulate matter emissions
from the wood burning indirect heat exchangers shall not exceed the allowable emission
rates listed below:
. Source
E�mLsslan L1mt
I
ES-1
(Ibs/milIi B )
tu
Stoker type wood-fired Boiler 0.41
(10.54 million Btu per hour maximum heat input) ,
4. PARTICULATE CONTROL REQUIREMENT- As required by 15A NCAC 2D .0515
"Particulates from Miscellaneous Industrial Processes," particulate matter emissions from
the emission sources shall not exceed allowable emission rates. The allowable emission rates
are, as defined in 15A NCAC 2D .0515, a function of the process weight rate and shall be
determined by the following equation(s),where P is the process throughput rate in tons per
hour(tons/hr) and E is the allowable emission rate in pounds per hour(lbs/hr).
E= 4.10 * (P)0 67 for P <= 30 tons/hr, or
E= 55 * (P) o.ii_ 40 for P >30 tons/hr
5. SULFUR DIOXIDE CONTROL REQUIREMENT-As required by 15A NCAC 2D .0516
"Sulfur Dioxide Emissions from Combustion Sources," sulfur dioxide emissions from
Stoker type wood-fired Boiler, 10.54 million Btu per hour maximum heat input(300 BHP)
(ID No. ES-1) shall not exceed 2.3 pounds per million Btu heat input.

Permit No. 10146R04
Page 3
6. VISIBLE EMISSIONS CONTROL REQUIREMENT -As required by 15A NCAC 2D
.0521 "Control of Visible Emissions," visible emissions from the emission sources,
manufactured after July 1, 1971, shall not be more than 20 percent opacity when averaged
over a six-minute period, except that six-minute periods averaging not more than 87 percent
opacity may occur not more than once in any hour nor more than four times in any 24-hour
period. However, sources which must comply with a visible emissions standard in 15A
NCAC 2D .0524 "New Source Performance Standards" or .1110 "National Emission
Standards for Hazardous Air Pollutants" shall meet that standard instead of the 2D .0521
visible emissions standard.
7. 15A NCAC 2D .0524 "NEW SOURCE PERFORMANCE STANDARDS" - For Stoker
type wood-fired Boiler, 10.54 mmBtu/hr maximum heat input(300 BHP) (ID No. ES-1) and
Natural gas-fired boiler(16.739 mmBtu/hr maximum heat input) (ID No. ES-5), the
Permittee shall comply with all applicable provisions, including the notification,testing,
reporting, recordkeeping, and monitoring requirements contained in Environmental
Management Commission Standard 15A NCAC 2D .0524 "New Source Performance
Standards" (NSPS) as promulgated in 40 CFR 60, Subpart Dc, including Subpart A "General
Provisions."
a. NSPS Recordkeeping Requirements - In addition to any other recordkeeping
requirements of the EPA,the Permittee is required to maintain records as follows:
i. The amounts of each fuel combusted during each month; and
ii. All records required under this section shall be maintained for a period of two
years following the date of such record.
8. NOTIFICATION REQUIREMENT - As required by 15A NCAC 2D .0535,the Permittee of
a source of excess emissions that last for more than four hours and that results from a
malfunction, a breakdown of process or control equipment or any other abnormal
conditions, shall:
a. Notify the Director or his designee of any such occurrence by 9:00 a.m. Eastern time
of the Division's next business day of becoming aware of the occurrence and
describe:
i. the name and location of the facility,
ii. the nature and cause of the malfunction or breakdown,
iii. the time when the malfunction or breakdown is first observed,
iv. the expected duration, and
V. an estimated rate of emissions.
b. Notify the Director or his designee immediately when the corrective measures have
been accomplished.

Permit No. 10146R04
Page 4
This reporting requirement does not allow the operation of the facility in excess of
Environmental Management Commission Regulations.
9. FUGITIVE DUST CONTROL REQUIREMENT -As required by 15A NCAC 2D .0540
"Particulates from Fugitive Dust Emission Sources," the Permittee shall not cause or allow
fugitive dust emissions to cause or contribute to substantive complaints or excess visible
emissions beyond the property boundary. If substantive complaints are received or excessive
fugitive dust emissions from the facility are observed beyond the property boundaries for six
minutes in any one hour(using Reference Method 22 in 40 CFR,Appendix A)',the owner or
operator may be required to submit a fugitive dust plan as described in 2D .0540(f).
"Fugitive dust emissions" means particulate matter that does not pass through a process
stack or vent and that is generated within plant property boundaries from activities such as:
unloading and loading areas,process areas stockpiles, stock pile working,plant parking lots,
and plant roads (including access roads and haul roads).
10. TOXIC AIR POLLUTANT EMISSIONS LIMITATION AND REPORTING
REQUIREMENT-Pursuant to 15A NCAC 2D .1100 "Control of Toxic Air Pollutants," and
in accordance with the approved application for an air toxic compliance demonstration,the
permit limits in the table below shall not be exceeded. The Permittee has submitted a toxic
air pollutant dispersion modeling analysis dated May 5,2016 for the facility's toxic air
pollutant emissions as listed in the below table. The modeling analysis was reviewed and
approved by the DAQ Air Quality Analysis Branch(AQAB) on June 2, 2016. Placement of
the emission sources, configuration of the emission points, and operation of the sources shall
be in accordance with the submitted dispersion modeling analysis and should reflect any
changes from the original analysis submittal as outlined in the AQAB review memo.
Affected Source(s) Toxic Air Pollutant Emission Limit
Arsenic & Compounds (total mass of
elemental AS, arsine and all inorganic 8.00 lbs/yr
compounds) (ASC (7778394))
ES-1 Benzene (71-43-2) 1551.20 lbs/yr
Stoker type wood-fired Boiler Chromium (VI)Non-Specific Compounds,
(10.54 million Btu per hour as Chrom(VI) (Component CRC) 1.28 lbs/yr
maximum heat input(300 BHP)) (NSCR6)
Formaldehyde (50-00-0) 0.1856 lbs/hr
Hydrogen chloride (hydrochloric acid) 8.001bs/hr
(7647-01-0)
_F
a. Restrictions - To ensure compliance with the above limits, the following restrictions
shall apply:
i. The amount of wood combusted in the boiler(ID No. ES-1) shall not exceed
4.68 tons per hour.
ii. The amount of wood combusted in the boiler(ID No. ES-1) shall not exceed
41,000 tons per consecutive 12-month period.

Permit No. 10146R04
Page 5
b. Recordkeeping Requirements - The following recordkeeping requirements apply:
i. The Permittee shall record the total amount of wood, in tons, combusted each day in
the boiler(ID No. ES-1).
ii. The Permittee shall record monthly and total annually the amount of wood
combusted in the boiler(ID No. ES-1)for each of the previous consecutive 12-
month periods.
11. OPERATIONAL RESTRICTION - The Permittee shall only operate either the Natural gas-fired
boiler(16.739 mmBtu/hr maximum heat input) (ID No. ES-5) or the Stoker type wood-fired Boiler
(10.54 mmBtu/hr maximum heat input(300 BHP))(ID No. ES-1),not both simultaneously, to
ensure emissions do not exceed Toxic Permit Emission Rates (TPERs).
12. GENERALLY AVAILABLE CONTROL TECHNOLOGY-For the Stoker type wood-fired
Boiler, 10.54 million Btu per hour maximum heat input(300 BHP) (ID No. ES-1),the Permittee
shall comply with all applicable provisions, including the notification,testing, and monitoring
requirements contained in Environmental Management Commission Standard 15A NCAC 2D
.1111, as promulgated in 40 CFR 63, Subpart JJJJJJ, "National Emission Standards for Hazardous
Air Pollutants for Area Sources: Industrial, Commercial, and Institutional Boilers", including
Subpart A "General Provisions."
a. Compliance Requirements -As required by 15A NCAC 2D .1111,the Permittee shall
comply with the following requirements:
i. General Duty Clause (40 CFR 63.11205(a)) -At all times the Permittee shall operate
and maintain any affected source, including associated air pollution control
equipment and monitoring equipment, in a manner consistent with safety and good
air pollution control practices for minimizing emissions.
ii. Boiler Tune-up (40 CFR 63.11223) -An initial boiler tune-up is required by March
21,2014. If the unit is not operating on the required date for a tune-up,the tune-up
must be conducted within thirty days of startup. The Permittee shall comply with the
following with respect to the tune-up:
A. Periodic tune-ups: A biennial tune-up is required and shall be conducted no
more than 25 months after the previous tune-up. The following units are only
required to conduct a tune-up every five years: seasonal boilers (shutdown for
7 consecutive months or 210 consecutive days each 12-month period due to
seasonal conditions; only biomass or oil), limited-use boilers, and units with
oxygen trim systems, as defined in 40 CFR 63.11237. Each five-year tune-up
must be conducted within 61 months of the previous tune-up.
B. Fuel required for the tune-up: The permittee shall conduct the tune-up while
burning the type of fuel (or fuels in the case of boilers that routinely burn two
types of fuels at the same time)that provided the majority of the heat input to
the boiler over the 12 months prior to the tune-up.
C. As applicable, inspect the burner, and clean or replace any components of the
burner as necessary. The Permittee may delay the burner inspection until the

Permit No. 10146R04
Page 6
next scheduled unit shutdown,but must inspect each burner at least once
every 36 months (72 months for 5-year tune-ups).
D. Inspect the flame pattern, as applicable, and adjust the burner as necessary to
optimize the flame pattern. The adjustment should be consistent with the
manufacturer's specifications, if available.
E. Inspect the system controlling the air-to-fuel ratio, as applicable, and ensure
that it is correctly calibrated and functioning properly. The Permittee may
delay the air to fuel ratio inspection until the next scheduled unit shutdown,
but must conduct the inspection at least once every 36 months (72 months for
5-year tune-ups).
F. Optimize total emissions of carbon monoxide. This optimization should be
consistent with the manufacturer's specifications, if available, and with any
nitrogen oxide requirement to which the unit is subject.
G. Measure the concentrations in the effluent stream of carbon monoxide in
parts per million,by volume, and oxygen in volume percent,before and after
the adjustments are made (measurements may be either on a dry or wet basis,
as long as it is the same basis before and after the adjustments are made).
Measurements may be taken with a portable CO analyzer.
b. Notification and Reporting Requirements - In addition to the notification and reporting
requirements of the Environmental Protection Agency (EPA),the Permittee is required to
NOTIFY the Regional Supervisor,DAQ, in WRITING, of the following:
i. Compliance Report must be prepared by March 1 of every other year(or
every five years depending on the frequency of the tune-up requirements)
starting March 1 the year following the first periodic tune-up, and submitted
upon request. The report must meet the requirements of 40 CFR
63.11225(b)(1-2).
c. Recordkeeping Requirements - In addition to any other recordkeeping requirements of the
EPA,the Permittee shall maintain the following records as defined under 40 CFR
63.11225(c):
i. Copies of all required notifications.
ii. Maintain the following records to document conformance with the work practices,
emission reduction measures, and management practices:
A. Tune-up records -records must identify each boiler,the date of tune-up,the
procedures followed for tune-up,the manufacturer's specifications to which
the boiler was tuned, and the following:
I. The concentrations of CO in the effluent stream in parts per million,
by volume, and oxygen in volume percent, measured at high fire or
typical operating load, before and after the tune-up of the boiler.

Permit No. 10146R04
Page 7
II. A description of any corrective actions taken as a part of the tune-up
of the boiler.
III. The type and amount of fuel used over the 12 months prior to the
tune-up of the boiler but only if the unit was physically and legally
capable of using more than one type of fuel during that period. Units
sharing a fuel meter may estimate the fuel use by each unit.
B. A copy the Energy Assessment required by 40 CFR 63.11214(c).
C. Seasonal boilers -For each boiler that meets the definition of seasonal boiler,
you must keep records of days of operation per year.
D. Records of non-waste determinations per 40 CFR 63.11225(c)(2)(ii).
iii. Malfunction Records -Records of the occurrence and duration of each malfunction
of the boiler, or of the associated air pollution control and monitoring equipment.
Records of actions taken during periods of malfunction to minimize emissions in
accordance with the general duty to minimize emissions in 40 CFR 63.11205(a),
including corrective actions to restore the malfunctioning boiler, air pollution
control, or monitoring equipment to its normal or usual manner of operation.
iv. Record Retention-You must keep each record for 5 years following the date of each
recorded action.
12. CONTROL AND PROHIBITION OF ODOROUS EMISSIONS -As required by 15A NCAC 2D
.1806 "Control and Prohibition of Odorous Emissions" the Permittee shall not operate the facility
without implementing management practices or installing and operating odor control equipment
sufficient to prevent odorous emissions from the facility from causing or contributing to
objectionable odors beyond the facility's boundary.
13. TOXIC AIR POLLUTANT EMISSIONS LIMITATION REQUIREMENT-Pursuant to 15A
NCAC 2Q .0711 "Emission Rates Requiring a Permit," for each of the below listed toxic air
pollutants (TAPs),the Permittee has made a demonstration that facility-wide actual emissions,
where one or more emission release points are obstructed or non-vertically oriented, do not exceed
the Toxic Permit Emission Rates (TPERs) listed in 15A NCAC 2Q .0711(a). The facility shall be
operated and maintained in such a manner that emissions of any listed TAPS from the facility,
including fugitive emissions,will not exceed TPERs listed in 15A NCAC 2Q .0711(a).
a. A permit to emit any of the below listed TAPs shall be required for this facility if actual
emissions from all sources will become greater than the corresponding TPERs.
b. PRIOR to exceeding any of these listed TPERs,the Permittee shall be responsible for
obtaining a permit to emit TAPs and for demonstrating compliance with the requirements of
15A NCAC 2D .1100 "Control of Toxic Air Pollutants".

Permit No. 10146R04
Page 8
c. In accordance with the approved application,the Permittee shall maintain records of
operational information demonstrating that the TAP emissions do not exceed the TPERs as
listed below:
YD
zt
C1PC1IlOg8IIS �Uhr `ySteItlie s
s�'oxicants I� t
(Ib/yr} (lb/day} 77
Taxi+cants yIt
Acetaldehyde (75-07-0) .1 r F 6.8
Acrolein(107-02-8) � 0.02
Ammonia(as NH3) (7664-41-7) ( F0.68
1lBenzo(a)pyrene (Component of 83329/POMTV & 2.2
56553/7PAH) (50-32-8)
Beryllium Metal (unreacted) � --+-"—_
0.28
(Component of BEC) (7440-41-7) (
Cadmium Metal, elemental,unreacted !
;(Component of CDC) (7440-43-9) 0.37
lCarbon tetrachloride (56-23-5) j 460
Chlorine (7782-50-5) F 0.79 0.23
€Chlorobenzene (108-90-7) i 46
jChloroform (67-66-3) 290 ( �_
Chromium(VI) Soluble Chromate Compounds
0.013
I(Component of CRC) (So1CR6) I
IEthylene dichloride (1,2-dichloroethane) (107-06-2) 260
Hexachlorodibenzo-p-dioxin 1,2,3,6,7,8 (57653-85-7) 0.0051
MEK(methyl ethyl ketone, 2-butanone) (78-93-3) j 78 22.4
Methylene chloride (75-0972) 1,600 0.39
Nickel metal (Component of NIC) (7440-02-0) � i 0.13 1F—
jPentachlorophenol (87-86-5) 0.063 0.0064
Perchloroeth lene tetrachloroeth lene 127-18-4 13,000
Phenol (108-95-2) _ �0.24�� �_
FTetrachlorodibenzo-p-dioxin, 2,3,7,8- (Component of& 83329/POMTV) (1746-01-6) 0.0002
Toluene (108-88-3) m_ 9 14.4�
Vinyl chloride (75-01-4) 26 IF
Xylene (mixed isomers) (1330-20-7) 57 16.4

Permit No. 10146R04
Page 9
B. GENERAL CONDITIONS AND LIMITATIONS
1. In accordance with G.S. 143-215.108(c)(1), TWO COPIES OF ALL DOCUMENTS,
REPORTS, TEST DATA, MONITORING DATA,NOTIFICATIONS, REQUESTS FOR
RENEWAL, AND ANY OTHER INFORMATION REQUIRED BY THIS PERMIT shall
be submitted.to the:
Regional Supervisor
North Carolina Division of Air Quality
Fayetteville Regional Office
Systel Building
225 Green Street, Suite 714
Fayetteville,NC 28301-5094
910-433-3300
For identification purposes, each submittal should include the facility name as listed on the
permit,the facility identification number, and the permit number.
2. RECORDS RETENTION REQUIREMENT- In accordance with 15A NCAC 2D .0605,
any records required by the conditions of this permit shall be kept on site and made available
to DAQ personnel for inspection upon request. These records shall be maintained in a form
suitable and readily available for expeditious inspection and review.These records must be
kept on site for a minimum of 2 years, unless another time period is otherwise specified.
3. ANNUAL FEE PAYMENT -Pursuant to 15A NCAC 2Q .0203(a),the Permittee shall pay
the annual permit fee within 30 days of being billed by the DAQ. Failure to pay the fee in a
timely manner will cause the DAQ to initiate action to revoke the permit.
4. EQUIPMENT RELOCATION- In accordance with 15A NCAC 2Q .0301, a new air permit
shall be obtained by the Permittee prior to establishing,building, erecting,using, or
operating the emission sources or air cleaning equipment at a site or location not specified in
this permit.
5. REPORTING REQUIREMENT - In accordance with 15A NCAC 2Q .0309, any of the
following that would result in previously unpermitted,new, or increased emissions must be
reported to the Regional Supervisor, DAQ:
changes in the information submitted in the application regarding facility emissions;
a. changes that modify equipment or processes of existing permitted facilities; or
b. changes in the quantity or quality of materials processed.
If appropriate,modifications to the permit may then be made by the DAQ to reflect any
necessary changes in the permit conditions. In no case are any new or increased emissions
allowed that will cause a violation of the emission limitations specified herein.

Permit No. 10146R04
Page 10
6. In accordance with 15A NCAC 2Q .0309,this permit is subject to revocation or
modification by the DAQ upon a determination that information contained in the application
or presented in the support thereof is incorrect, conditions under which this permit was
granted have changed, or violations of conditions contained in this permit have occurred. In
accordance with G.S. 143-215.108(c)(1), the facility shall be properly operated and
maintained at all times in a manner that will effectuate an overall reduction in air pollution.
Unless otherwise specified by this permit, no emission source may be operated without the
concurrent operation of its associated air cleaning device(s) and appurtenances.
7. CHANGES NOT REQUIRING PERMIT REVISIONS -Pursuant to 15A NCAC 02Q
.0318, changes to the facility that are not exempt pursuant to 15A NCAC 02Q .0102 may be
allowed without first modifying an applicable air permit if the change(s)meet(s)the
requirements of 15A NCAC 02Q .0318(b)(1) through(b)(5) and the owner or operator
notifies the Director in writing,using forms provided by the Division, seven calendar days
before the change is made. Within 10 business days of receipt of the notice,the Division
shall notify the owner or operator of its determination of whether the change(s) meet(s) the
requirements of 15A NCAC 02Q .0318(b)(1) through(b)(5).
8. In accordance with G.S. 143-215.108(c)(1),this permit is nontransferable by the Permittee.
Future owners and operators must obtain a new air permit from the DAQ.
9. In accordance with G.S. 143-215.108(c)(1),this issuance of this permit in no way absolves
the Permittee of liability for any potential civil penalties which may be assessed for
violations of State law which have occurred prior to the effective date of this permit.
10. In accordance with G.S. 143-215.108(c)(1),this permit does not relieve the Permittee of the
responsibility of complying with all applicable requirements of any Federal, State, or Local
water quality or land quality control authority.
11. In accordance with 15A NCAC 2D .0605, reports on the operation and maintenance of the
facility shall be submitted by the Permittee to the Regional Supervisor, DAQ at such
intervals and in such form and detail as may be required by the DAQ. Information required
in such reports may include,but is not limited to,process weight rates, firing rates,hours of
operation, and preventive maintenance schedules.
12. A violation of any term or condition of this permit shall subject the Permittee to enforcement
pursuant to G.S. 143-215.114A, 143-215.114B, and 143-215.114C, including assessment of
civil and/or criminal penalties.
13. Pursuant to North Carolina General Statute 143-215.3(a)(2),no person shall refuse entry or
access to any authorized representative of the DAQ who requests entry or access for
purposes of inspection, and who presents appropriate credentials,nor shall any person
obstruct,hamper, or interfere with any such representative while in the process of carrying
out his official duties. Refusal of entry or access may constitute grounds for permit
revocation and assessment of civil penalties.

Permit No. 10146R04
Page 11
14. In accordance with G.S. 143-215.108(c)(1),this permit does not relieve the Permittee of the
responsibility of complying with any applicable Federal, State, or Local requirements
governing the handling, disposal, or incineration of hazardous, solid, or medical wastes,
including the Resource Conservation and Recovery Act(RCRA) administered by the
Division of Waste Management.
15. PERMIT RETENTION REQUIREMENT - In accordance with 15A NCAC 2Q .0110,the
Permittee shall retain a current copy of the air permit at the site. The Permittee must make
available to personnel of the DAQ, upon request,the current copy of the air permit for the
site.
16. CLEAN AIR ACT SECTION 112(r) REQUIREMENTS -Pursuant to 15A NCAC 2D .2100
"Risk Management Program," if the Permittee is required to develop and register a risk
management plan pursuant to Section 112(r) of the Federal Clean Air Act,then the
Permittee is required to register this plan with the USEPA in accordance with 40 CFR Part
68.
17. PREVENTION OF ACCIDENTAL RELEASES - GENERAL DUTY -Pursuant to Title I
Part A Section 112(r)(1) of the Clean Air Act "Hazardous Air Pollutants - Prevention of
Accidental Releases -Purpose and General Duty," although a risk management plan may not
be required, if the Permittee produces,processes, handles, or stores any amount of a listed
hazardous substance,the Permittee has a general duty to take such steps as are necessary to
prevent the accidental release of such substance and to minimize the consequences of any
release. This condition is federally-enforceable only.
18. GENERAL EMISSIONS TESTING AND REPORTING REQUIREMENTS -If emissions
testing is required by this permit, or the DAQ, or if the Permittee submits emissions testing
to the DAQ in support of a permit application or to demonstrate compliance,the Permittee
shall perform such testing in accordance with 15A NCAC 2D .2600 and follow all DAQ
procedures including protocol approval, regional notification,report submittal, and test
results approval. Additionally, in accordance with 15A NCAC 2D .0605,the Permittee shall
follow the procedures for obtaining any required audit sample and reporting those results.
Permit issued this the 29t'of April, 2022.
NORTH CAROLINA ENVIRONMENTAL MANAGEMENT COMMISSION
AA
a
Heather Carter
Regional Supervisor
By Authority of the Environmental Management Commission
Air Permit No. 10146R04

ATTACHMENT to Permit No. 10146R04, April 29, 2022
Insignificant/Exempt Activities
n'
IES-1
Band saw mill for green lumber 02Q .0102 (h)(5) No Yes
(inside building)
IES-2
Circular saw mill for green lumber 02Q .0102 (h)(5) No Yes
(inside building)
F I-LPGBoiler
LPG-fired boiler, 3 02Q .0102 (h)(1)(B) Yes Yes
(7.53 mmBtu/hr maximum heat input)
1. Because an activity is exempted from being required to have a permit or permit modification
does not mean that the activity is exempted from an applicable requirement or that the owner
or operator of the source is exempted from demonstrating compliance with any applicable
requirement.
2. When applicable, emissions from stationary source activities identified above shall be
included in determining compliance with the permit requirements for toxic air pollutants
under 15A NCAC 2D .1100 "Control of Toxic Air Pollutants" or 2Q .0711 "Emission Rates
Requiring a Permit."
3. Sample permit conditions showing the regulatory requirements for exempt sources subject to
NESHAP,NSPS, and NCAC rules may be found here:
https://deq.nc.gov/qqpermitconditions