AQ_F_0200083_20240208_PRMT_CmbPrmtFile_R05

ROY COOPER
Governor
ELIZABETH S. BISER
Secretary
MICilAEL A. ABRACZINSKAS
Director
■f^STATg
1Wi
NORTH CAROLINA
Environmental Quality
February 8, 2024
Mr. Joseph Edwards
Director Home Furnishing Ops
Hickory Springs Hiddenite
P.O. Box 128
Hickory, NC 28603
Subject: Air Permit No. 08502R05
Hickory Springs Hiddenite
Hiddenite, Alexander County, North Carolina
Permit Class: Small
Facility ID# 0200083
Dear Mr. Edwards: .
In accordance with your completed application received December 18, 2023, we are
forwarding herewith Permit No. 08502R05 to Hickory Springs Hiddenite, Hiddenite, AlexanderCounty, North Carc^lina for the construction and operation of air emissions sources or air cleaning
devices-and appurtenances.
If any parts, requirements, or limitations contained in this permit are unacceptable to you,
you have the right to file a petition for contested case hearing in the North Carolina Office of
Administrative Hearings. Information regarding the right, procedure, and time limit for permittees
and other persons aggrieved to file such a petition is contained in the attached "Notice Regarding
the Right to Contest a Division of Air Quality Permit Decision."
Unless exempted by a condition of this permit or the regulations, construction of new
air pollution sources or air cleaning devices, or modifications to the sources or air cleaning
devices described in this permit must he covered under a permit issued by the Division of Air
Quality prior to construction. Failure to do so is a violation of G.S. 143-215.108 and may
subject the Permittee to civil or criminal penalties as described in G.S. 143-215.114A and 143-
215.114B.
This permit shall be effective from February 8, 2024 until January 31,2032, is
nontransferable to future owners and operators, and shall be subject to the conditions and limitations
as specified therein.
m North Carolina Department of Environmental Quality | Division of Air Quality
Moonesvllle Regional Office j 610 East Center Avenue, Suite 301 | Mooresvllle, NC 28115
704.663.1699 T I 704.663.6040 F
Joseph Edwards
February 8, 2024
Page 2
Changes have been made to the permit stipulations. The Permittee is responsible for
carefully reading the entire permit and evaluating the requirements of each permit
stipulation. The Permittee shall comply with all terms, conditions, requirements, limitations
and restrictions set forth in this permit. Noncompliance with any permit condition is grounds
for enforcement action, for permit termination, revocation and reissuance, or modification, or
for denial of a permit renewal application. Specific changes and additions are summarized
below (note: this list may not include all changes and additions):
• A rule change that became effective November 1, 2016, removed the "state-wide"
applicability of 2D .0958, and it now only applies to the counties/townships listed in the
regulation. This facility is not located in one of the areas still subject to this regulation;
therefore, the condition for 2D .0958 is being removed from the permit.
Should you have any questions concerning this matter, please contact Jennifer Manning at 704-235-
2224 [e-mail].
Sincerely,
Melinda Wolanin, Regional Supervisor
Division of Air Quality, NC DEQ
JAM
Enclosures
c: Laserfiche
https://ncconnect.sharepoint.eom/sites/DAQ-MRO/Counties/ALEXANDER/00083/R05_PERMIT.docx
NOTICE REGARDING THE RIGHT TO CONTEST A DIVISION OF AIR QUALITY
PERMIT DECISION
Riglit of the Permit Applicant or Permittee to File a Contested Case: Pursuant to NCOS 143-
215.108(e), a permit applicant or permittee who is dissatisfied with the Division of Air Quality's
decision on a permit application may commence a contested case by filing a petition under
NCOS 150B-23 in the Office of Administrative Hearings within 30 days after the Division
notifies the applicant or permittee of its decision. If the applicant or permittee does not file a
petition within the required time, the Division's decision on the application is final and is not
subject to review. The filing of a petition will stay the Division's decision until resolution of the
contested case.
Right of Other Persons Aggrieved to File a Contested Case: Pursuant to NCOS 143-
215.108(el), a person other than an applicant or permittee who is a person aggrieved by the
Division's decision on a permit application may commence a contested case by filing a petition
under NCOS 150B-23 within 30 days after the Division provides notice of its decision on a
permit application, as provided in NCOS 150B-23(f), or by posting the decision on a publicly
available Web site. The filing of a petition under this subsection does not stay the Division's
decision except as ordered by the administrative law judge under NCOS 150B-33(b).
General Filing Instructions: A petition for contested ease hearing must be in the form of a
written petition, conforming to NCGS 150B-23, and filed with the Office of Administrative
Hearings, 1711 New Hope Church Road, Raleigh NC, 27609, along with a fee in an amount
provided in NCGS 150B-23.2. A petition for contested case hearing form may be obtained upon
request from the Office of Administrative Hearings or on its website at
https://www.oah.nc.gov/hearings-division/filing/hearing-forms. Additional specific instructions
for filing a petition are set forth at 26 NCAC Chapter 03.
Service Instructions: A party filing a contested case is required to serve a copy of the petition,
by any means authorized under 26 NCAC 03 .0102, on the process agent for the Department of
Environmental Quality: -
William F. Lane, General Coimsel
North Carolina Department of Environmental Quality
1601 Mail Service Center
Raleigh, North Carolina 27699-1601
If the party filing the petition is a person aggrieved other than the permittee or permit applicant,
the party must also serve the permittee in accordance with NCGS 150B-23(a).
Additional information is available at https://www.oah.nc.gov/hearings-division/hearing-
process/filing-contested-case. Please contact the OAH at 984-236-1850 or
[e-mail] with all questions regarding the filing fee and/or the details of the
filing process.
NORTH CAROLINA ENVIRONMENTAL MANAGEMENT COMMISSION
DEPARTMENT OF ENVIRONMENTAL QUALITY
DIVISION OF AIR QUALITY
AIR PERMIT NO. 08502R05
Issue Date: February 8, 2024 Effective Date: February 8, 2024
Expiration Date: January 31, 2032 Replaces Permit: 08502R04
To construct and operate air emission source(s) and/or air cleaning device(s), and for the
discharge of the associated air contaminants into the atmosphere in accordance with the provisions
of Article 21B of Chapter 143, General Statutes of North Carolina (NCGS) as amended, and other
applicable Laws, Rules and Regulations,
Hickory Springs Hiddenite
161 Sharpe Lane
Hiddenite, Alexander County, North Carolina
Permit Class: Small
Facility ID# 0200083
(the Permittee) is hereby authorized to construct and operate the air emissions sources and/or air
cleaning devices and appurtenances described below:
Emission
Source ID
Emission Source
Description
Control
System ID
Control System
Description
ES-F-01 (NESHAP)flexible polyurethane foam
gluing operation N/A i N/A
in accordance with the completed application 0200083.23A received December 18, 2023 including
any plans, specifications, previous applications, and other supporting data, all of which are filed
with the Department of Environmental Quality, Division of Air Quality (DAQ) and are incorporated
as part of this permit.
This permit is subject to the following specified conditions and limitations including any
TESTING. REPORTING. OR MONITORING REQUIREMENTS:
A. SPECIFIC CONDITIONS AND LIMITATIONS
I. Any air emission sources or control devices authorized to construct and operate above must
be operated and maintained in accordance with the provisions contained herein. The
Permittee shall comply with applicable Environmental Management Commission
Regulations, including Title 15A North Carolina Administrative Code (NCAC), Subchapter
2D .0202, 2D .0521, 2D .0535, 2D .0540, 2D .1111 and 2D .1806.
Permit No. 08502R05
Page 2
2. PERMIT RENEWAL AND EMISSION INVENTORY REQUIREMENT - The Permittee,
at least 90 days prior to the expiration date of this permit, shall request permit renewal by
letter in accordance with 15A NCAC 2Q .0304(d) and (f). Pursuant to ISA NCAC 2Q
.0203(i), no permit application fee is required for renewal of an existing air permit (without
a modification request). The renewal request (with application Form A) should be submitted
to the Regional Supervisor, DAQ. Also, at least 90 days prior to the expiration date of this
permit, the Permittee shall submit the air pollution emission inventory report (with
Certification Sheet) in accordance with ISA NCAC 2D .0202, pursuant to N.C. General
Statute 143 2IS.6S. The report shall be submitted to the Regional Supervisor, DAQ and shall
document air pollutants emitted for the 2030 calendar year.
3. VISIBLE EMISSIONS CONTROL REQUIREMENT - As required by 1SA NCAC 2D
.0S21 "Control of Visible Emissions," visible emissions fi:om the. emission sources,
manufactured after July 1,1971, shall not be more than 20 percent opacity when averaged
over a six-minute period, except that six-minute periods averaging not more than 87 percent
opacity may occur not more than once in any hour nor more than four times in any 24-hour
period. However, sources which must comply with a visible emissions standard in ISA
NCAC 2D .0524 "New Source Performance Standards" or .1110 "National Emission
Standards for Hazardous Air Pollutants" shall meet that standard linstead of the 2D .0521
visible emissions standard.
4. NOTIFICATION REQUIREMENT - As required by ISA NCAC 2D .0535, the Permittee of
a source of excess emissions that last for more than four hours and that results from a
malfunction, a breakdovra of process or control equipment or any other abnormal
. conditions, shall:
a. Notify the Director or his designee of any such occurrence by 9:00 a.m. Eastern time
of the Division's next business day of becoming aware of the occurrence and
describe:
i. the name and location of the facility,
ii. the nature and cause of the malfunction or breakdown,
iii. the time when the malfunction or breakdown is first observed,
iv. the expected duration, and
V. an estimated rate of emissions.
b. Notify the Director or his designee immediately when the corrective measures have
been accomplished.
This reporting requirement does not allow the operation of the facility in excess of
Environmental Management Commission Regulations.
Permit No. 08502R05
Page 3
5. FUGITIVE DUST CONTROL REQUIREMENT - As required by 15A NCAC 2D .0540
"Particulates from Fugitive Dust Emission Sources," the Permittee shall not cause or allow
fugitive dust emissions to cause or contribute to substantive complaints or excess visible
emissions beyond the property boundary. If substantive complaints are received or excessive
fugitive dust emissions from the facility are observed beyond the property boundaries for six
minutes in any one hour (using Reference Method 22 in 40 CFR, Appendix A), the owner or
operator may be required to submit a fugitive dust plan as described in 2D .0540(f).
"Fugitive dust emissions" means particulate matter that does not pass through a process
stack or vent and that is generated within plant property boundaries from activities such as:
unloading and loading areas, process areas stockpiles, stock pile working, plant parking lots,
and plant roads (including access roads and haul roads).
6. GENERALLY AVAILABLE CONTROL TECHNOLOGY IGACTl - For the Flexible
polyurethane foam fabrication operations, foam gluing operation (ID No. ES-F-01), the
Permittee shall comply with all applicable provisions of 40 CFR 63, Subpart 000000
"National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam
Production and Fabrication Area Sources", including Subpart A "General Provisions."
a. Standards and Compliance - Pursuant to 40 CFR 63.11416 the following standards
shall apply:
i. The Permittee shall not use any adhesive containing methylene chloride in a
flexible polyurethane foam fabrication process.
b: Recordkeeping Requirements - Pursuant to 40 CFR 63.11417 the following
recordkeeping requirements shall apply:
i. For foam fabrication operations with loop slitters, the Permittee shall retain
on site a statement signed and dated by a responsible official stating that the
facility does not use any adhesive containing methylene chloride in a flexible
polyurethane foam fabrication process.
ii. The Permittee shall demonstrate compliance with the requirements of
paragraph a.i. of this condition using adhesive usage records. Material Safety
Data Sheets or engineering calculations.
iii. The Permittee shall retain the records used to demonstrate compliance for
five years with the last two years of data retained on site. The remaining three
years of data may be retained off site.
iv. The Permittee shall make the records available for inspection upon request of
DAQ personnel.
Permit No. 08502R05
Page 4 '
7. CONTROL AND PROHIBITION OF ODOROUS EMISSIONS,- As required by 15A
NCAC 2D .1806 "Control and Prohibition of Odorous Emissions" the Permittee shall not
operate the facility without implementing management practices or installing and operating
odor control equipment sufficient to prevent odorous emissions from the facility from
causing or contributing to objectionable odors beyond the facility's boundary.
B. GENERAL CONDITIONS AND LIMITATIONS
1. In accordance with G.S. 143-215.108feXlL TWO COPIES OF ALL DOCUMENTS,
REPORTS. TEST DATA. MONITORING DATA. NOTIFICATIONS. REQUESTS FOR
RENEWAL. AND ANY OTHER INFORMATION REQUIRED BY THIS PERMIT shall
be submitted to the:
j
Regional Supervisor
North Carolina Division of Air Quality
Mooresville Regional Office
610 East Center Avenue, Suite 301
Mooresville, NC 28115
704-663-1699
For identification purposes, each submittal should include the facility name as listed on the
permit, the facility identification number, and the permit number.
2. RECORDS RETENTION REQUIREMENT - In accordance with 15A NCAC 2D .0605,
any records required by the conditions of this permit shall be kept on site and made available
to DAQ personnel for inspection upon request. These records shall be maintained in a form
suitable and readily available for expeditious inspection and review. These records must be
kept on site for a minimum of 2 years, unless another time period is otherwise specified.
3. ANNUAL FEE PAYMENT - Pursuant to 15A NCAC 2Q .0203(a), the Permittee shall psy
the annual permit fee within 30 days of being billed by the DAQ, Failure to pay the fee in a
timely manner will cause the DAQ to initiate action to revoke the permit.
4. EQUIPMENT RELOCATION - In accordance with 15A NCAC 2Q .0301, a new air permit
shall be obtained by the Permittee prior to establishing, building, erecting, using, or
operating the emission sources or air cleaning equipment at a site or location not specified in
this permit. i
5. REPORTING REQUIREMENT - In accordance with 15 A NCAC 2Q .0309, any of the
following that would result in previously unpermitted, new, or increased emissions must be
reported to the Regional Supervisor, DAQ:
a. changes in the information submitted in the application regarding facility emissions;
b. changes that modify equipment or processes of existing permitted facilities; or
c. changes in the quantity or quality of materials processed.
Permit No. 08502R05
Page 5
If appropriate, modifications to the permit may then be made by the D AQ to reflect any
necessary changes in the permit conditions. In no case are any new or increased emissions
allowed that will cause a violation of the emission limitations specified herein.
6. In accordance with 15A NCAC 2Q .0309, this permit is subject to revocation or
modification by the DAQ upon a determination that information contained in the application
or presented in the support thereof is incorrect, conditions under which this permit was
granted have changed, or violations of conditions contained in this permit have occurred. In
accordance with G.S. 143-215.108(c)(1), the facility shall be properly operated and
maintained at all times in a manner that vrill effectuate an overall reduction in air pollution.
Unless otherwise specified by this permit, no emission source may be operated without the
concurrent operation of its associated air cleaning device(s) and appurtenances.
7. CHANGES NOT REQUIRING PERMIT REVISIONS - Pursuant to 15A NCAC 02Q
.0318, changes to the facility that are not exempt pursuant to 15A NCAC 02Q .0102 may be
allowed without first modifying an applicable air permit if the change(s) meet(s) the
requirements of ISA NCAC 02Q .0318(b)(1) through (b)(5) and the owner or operator
notifies the Director in writing, using forms provided by the Division, seven calendar days
before the change is made.. Within 10 business days of receipt of the notice, the Division
shall notify the ovmer or operator of its determination of whether the change(s) meet(s) the
requirements of ISA NCAC 02Q .0318(b)(1) through (b)(5).
8. In accordance with G.S. 143-215.108(c)(1), this permit is nontransferable by the Permittee.
Future owners and operators must obtain a new air permit from the DAQ.
9. In accordance with G.S. 143-215.108(c)(1), this issuance of this permit in no way absolves
the Permittee of liability for any potential civil penalties which may be assessed for
violations of State law which have occurred prior to the effective date of this permit.
10. In accordance with G.S. 143-215.108(c)(1), this permit does not relieve the Permittee of the
responsibility of complying with all applicable requirements of any Federal,- State, or Local
water quality or land quality control authority.
11. In accordance with ISA NCAC 2D .0605, reports on the operation and maintenance of the
facility shall be submitted by the Permittee to the Regional Supervisor, DAQ at such
intervals and in such form and detail as may be required by the DAQ. Information required
in such reports may include, but is not limited to, process weight rates, firing rates, hours of
operation, and preventive maintenance schedules.
12. A violation of any term or condition of this permit shall subject the Permittee to enforcement
pursuant to G.S. 143-215.114A, 143-215.114B, and 143-215.114C, including assessment of
civil and/or criminal penalties.
13. Pursuant to North Carolina General Statute 143-215.3(a)(2), no person shall refuse entry or
access to any authorized representative of the DAQ who requests entry or access for
purposes of inspection, and who presents appropriate credentials, nor shall any person
obstruct, hamper, or interfere with any such representative while in the process of carrying
Permit No. 08502R05
Page 6
out his official duties. Refusal of entry or access may constitute grounds for permit
revocation and assessment of civil penalties.
14. In accordance with G.S. 143-215.108(c)(1), this permit does not relieve the Permittee of the
responsibility of complying with any applicable Federal, State, or Local requirements
governing the handling, disposal, or incineration of hazardous, solid, or medical wastes,
including the Resource Conservation and Recovery Act (RCRA) administered by the
Division of Waste Management.
15. PERMIT RETENTION REQUIREMENT - In accordance with 15A NCAC 2Q .0110, the
Permittee shall retain a current copy of the air permit at the site. The Permittee must make
available to personnel of the DAQ, upon request, the current copy of the air permit for the
site.
16. CLEAN AIR ACT SECTION 112(r) REQUIREMENTS - Pursuant to 15A NCAC 2D .2100
"Risk Management Program," if the Permittee is required to develop and register a risk
management plan pursuant to Section 112(r) of the Federal Clean Air Act, then the
Permittee is required to register this plan with the USEPA in accordance with 40 CFR Part
68.
17. GENERAL EMISSIONS TESTING AND REPORTING REQUIREMENTS - If emissions
testing is required by this permit, or the DAQ, or if the Permittee submits emissions testing
to the DAQ in support of a permit application or to demonstrate compliance, the Permittee
shall perform such testing in accordance with I5A NCAC 2D .2600 and follow all DAQ
procedures including protocol approval, regional notification, report submittal, and test
results approval. Additionally, in accordance with 15ANCAC 2D .0605, the Permittee shall
follow the procedures for obtaining any required audit sample and reporting those results. ,
Permit issued this the 8"^ of February, 2024.
NORTH CAROLINA ENVIRONMENTAL MANAGEMENT COMMISSION
Melinda Wolanin
Regional Supervisor
By Authority of the Environmental Management Commission
Air Permit No. 08502R05
https://ncconnect.sharepomt.eom/sites/DAQ-MRO/Counties/ALEXANDER/00083/R05 REVIEW.docx
NORTH CAROLINA DIVISION OF
AIR QUALITY
Application Review
Issue Date: 2/8/24
Region: Mooresville Regional Office
County: Alexander
NC Facility ID: 0200083
Inspector's Name: Emily Supple
Date of Last Inspection: 08/18/2021
Compliance Code: 3 / Compliance - inspection
Facility Data
Applicant (Facility's Name): Hickory Springs Hiddenite
Facility Address:
Hickory Springs Hiddenite
161 Sharpe Lane
Hiddenite, NC 28636
SIC: 3086 / Plastics Foam Products
NAICS: 32614 / Polystyrene Foam Product Manufacturing
Facility Classification: Before: Small After: Small
Fee Classification: Before: Small After: Small
Permit Applicability (this application only)
SIP: N
NSPS: N
NESHAP: N
PSD: N
PSD Avoidance: N
NC Toxics: N
112(r): N
Other: N
Contact Data Application Data
Application Number: 0200083.23A
Date Received: 12/18/2023
Application Type: Renewal 1
Application Schedule: State 1
Existing Permit Data 1
Existing Permit Number: 08502/R04
Existing Permit Issue Date: 04/13/2016
Existing Permit Expiration Date: 03/31/2024
Facility Contact
Mark Sigmon
Plant Superintendent
[phone]
161 Sharpe Lane
Hiddenite, NC 28636
Authorized Contact
Joseph Edwards
Director Home
Fumishing Ops
[phone]
P.O. Box 128
Hickory, NC 28603
Technical Contact
Zenaida Camacho
EHS Manager
[phone]
P. O. Box 128
Hickory, NC 28603
Review Engineer: Jennifer Manning
Review Enzfheer's Signature: A ^ Date: J^l if / j
Comments / Recommendations:
Issue 08502/R05
Permit Issue Date: 2/8/24
Permit Expiration Date: 1/31/32
1. PURPOSE OF APPLICATION:
Application is made for renewal of the air permit.
2. CHRONOLOGY;
DaM;Event
December 18, 2023 The application was received.
December 21, 2023 jThe acknowledgment letter was sent.
Permit Review
Page 2
3. EMISSION SOURCE CHANGES;
a. Permitted Emission Sources
There are no changes to the equipment from this application.
b. Insignificant/Exempt Activities
There are no changes to the equipment from this application.
4. REVIEW OF REGULATIONS:
The Permittee shall comply with the following Environmental Management Commission
Regulations, including Title 15A North Carolina Administrative Code (NCAC). These existing
regulations have been reviewed in previous reviews and/or inspection reports and it was
determined that the facility was in compliance with all regulations at that time. There are no
changes expected to continued compliance.
« 2D .0202 - Registration of Air Pollution Sources
• 2D .0521 - Control of Visible Emissions
• 2D .0535 - Excess Emissions Reporting and Malfunctions
• 2D .0540 - Particulates from Fugitive Dust Emission Sources
• 2D . 1111 - NESHAP Subpart OOOOOO
• 2D . 1806 - Control and Prohibition of Odorous Emissions
5. APPLICIBILITY TO THE FOLLOWING:
a. NSPS-
There are no NSPS regulations that apply.
b. NESHAP-
The facility is subject to Subpart OOOOOO - "National Emission Standards for Hazardous
Air Pollutants for Polyurethane Foam Production and Fabrication Area Sources."
c. PSD INCREMENT TRACKING-
This renewal does not affect PSD increment tracking.
d. ATTAINMENT STATUS-
This facility is located in an area that is either in attainment or unclassifiable for all
pollutants.
Permit Review
Page 3
e. 112(r)-
This facility is not subject to RMP requirements of the 112(r) program since it does not
use or store any of the regulated chemicals in quantities above the threshold levels in the
rule.'
f. TOXICS-
This facility is NOT subject to toxics. This application does not trigger a toxics review.
6. FACILITY-WIDE EMISSIONS:
The VOC emissions are taken from the previous air permit review since there are no changes
expected from this renewal. However, the SDS showed hexane as a component in the glue at a
maximum of 1%. Therefore, hexane will be shown ks the highest and total HAP at a rate of 1% of
the VOCs.
The VOCs could have been recalculated based on the lower usage in the previous inventoiy;
however, it is reasonable to keep the higher emissions for the potential emissions since it
represents worst case.
Polhit.int Potential Emis^ion^
.After C ontrols/Limitations,(tpy)„
Pote^htial Emissions
Before Gdntrols/LirfaitationsTtPv)
TSP 0 0
PMIO 0 0
SO2 0 0
NOx 0 0
VOC 49.82 49.82
CO 0 0
Highest HAP
(hexane)0.50 0.50
Total HAP 0.50 0.50
7. TEXT FOR "CHANGES" PARAGRAPH IN PERMIT COVER LETTER:
• A rule change that became effective November 1, 2016, removed the "state-wide"
applicability of 2D .0958, and it now only applies to the counties/townships listed in the
regulation. This facility is not located in one of the areas still subject to this regulation;
therefore, the condition for 2D .0958 is being removed from the permit.
Permit Review
Page 4
8. RECOMMENDATION:
It is recommended that permit 08502R05 be issued.
JAM
ROY COOPER
Governor
ELIZABETH S. BISER
Secretary
MICHAEL A. ABRACZINSKAS
Director
1
S»w,
quw
NORTH CAROLINA
Environmental Quality
December 21,2023
Mr. Joseph Edwards
Director Home Furnishing Ops
Hickory Springs Hiddenite
P.O. Box 128
Hickory, NC 28603
SUBJECT: Receipt of Permit Application
Renewal of Permit No. 08502R04
Appilication No. 0200083.23A
Hickory Springs Hiddenite
Facility ID: 0200083, Hiddenite, Alexander County
Dear Mr. Edwards:
Your air permit application (0200083.23A) for Hickory Springs Hiddenite, located in Alexander
County, North Carolina was received by this division on December 18, 2023. This application
submittal did contain all the required elements and has been accepted for processing. Your
application will be considered complete as of December 18, 2023, unless informed otherwise by this
office within 45 days. Should you have any questions concerning this matter, please contact
Jennifer Manning at 704-235-2224 or by email [e-mail].
Sincerely,
Melinda Wolanin, Regional Supervisor
Division of Air Quality, NCDEQ
JAM
c: Laserfiche ^
https://ncconnect.sharepoint.eom/sites/DAQ-MRO/Counties/ALEXANDER/00083/R05_ACK_20231221.docx
OMitlf'
.^1 North Carolina Department of Environmental Quality | Division of Air Quality
Moore.sville Regional Office | 610 East Center Avenue, Suite 301 | Mooresville, NC 28115
704.663.1699 TI 704.663.6040 F
jjgyi SCAIMNC
VIA CERTIFIED MAIL
7Dn 112D □□□! 3S7T 2b7T ^^^'RONMENTAfo!,?''RecS?eo
December 5, 2023 DfC I 8 2023
Ms. Melinda WolaninRegional Supervisor '^Ooresv/lle region
North Carolina Division of Air Quality °'^'SiONMooresville Regional Office Quality
610 East Center Avenue, Suite 301
Mooresville, NC 28115
RE: Air Permit Renewal Application
Hickory Springs Manufacturing Company - Hiddenite Facility
Facility ID No. 0200083
Dear Ms. Wolanin:
Please find enclosed two (2) copies of the Air Permit renewal application for the Hickory Springs
Manufacturing (HSM) facility in Hiddenite, Alexander County, North Carolina (Hiddenite facility). The
Hiddenite facility is currently operating in accordance with Air Permit No. 08502R04, issued by the North
Carolina Department of Environmental Quality (NC DEQ) on April 13, 2016. The expiration date of Permit
No. 08502R04 is March 31, 2024.
In accordance with Condition A.2 of Permit No. 08502R04, HSM must submit a complete renewal
application at least 90 days in advance of the expiration date (i.e., by December 31, 2023). HSM is
requesting renewal of the Permit for the Hiddenite facility without modification. NC DEQ Forms A, A2
and A3 are included in Attachment 1 to this submittal.
Per Condition A.2 and ISA NCAC 02D .0202, HSM must submit an emissions inventory for calendar year
2022 (CY2022) with the renewal application. The CY2022 emissions inventory was submitted through
the NC DEQ Air Emissions Reporting On-Line (AERO) system on December 5, 2023. The signed AERQ
certification and supporting documentation for the CY2022 emissions inventory is included in
Attachment 2.
If you have any questions regarding the information in this renewal application, please contact Zenaida
Camacho at [phone] extension 3125 or via email at zcamacho(Shsmsolutions.com.
Sincerely,
HICKORY SPRINGS MANUFACTURING
Joseph Edwards
Director Home Furnishings Ops
Attachments
FORM A
GENERAL FACILITY INFORMATION
REVISED 03/03/23 NCDEQ/Divislon of Air Quality • Application for Air Permit to Construct/Operate 1 A
NOTE- APPUCATION WILL NOT BE PROCESSED WITHOUT THE FOLLOWING:
Q Local Zoning Constetency Determination
(new or modification only)Q Apjxoixlate Number of O^es of AF^ication Application Fee (please check one option below)
^ Responsible Ofriclaf/Authorized Contact Signature □ P.E. Seal (If required)□ Not Required □ ePayment □ Check Enclosed
GENERAL INFORMATION
Legal Corporate/Owner Name: Hickory Springs Manufacturing Company
Site Name: Hickory Springs Hiddenlte
Site Address (911 Address) Line 1: 161 Sharpe Lane
Site Address Line 2;
City: Hiddenite State; North Carolina
Zip Code: 28636 County: Alexander
CONTACT INPeRMATION
Responsible Official/Authorized Contact Invoice Contact
Name/Title: Joseph Edwards / Director Home Furnishings Ops Name/Title:Zenaida Camacho / EHS Manager
Mailing Address Line 1: P.O. Ek>x 128 Mailing Address Line 1;P.O. Box 128
Mailing Address Line 2:Mailing Address Line 2:
City: Hickory State; NC Zip Code: 28603 City: Hickory State: NC Zip Code:28603
Primary Phone No.: [phone] ext 3122 Fax No.:Primary Phone No.:[phone] ext. 3125 Fax No.:
Secondary Phone No.;Secondary Phone No.:
Email Address: IdedwardsdhsmsolutiQnf.COm Email Address:2camacho®hsmsolutions.com
Facility/Inspection Contact Permitn'echnical Contact
Name/Titie: Mark Sigmon / Plant Superintendent Name/Title:Zenaida Camacho / EHS Manager
Mailing Address Line 1: 161 Sharpe Lane Mailing Address Line 1:P.O. Box 128
Mailing Address Line 2:Mailing Address Line 2:
City: Hiddenite State; NC Zip Code: 28636 City: Hickory State: NC Zip Code;28603
Primary Phone No.: [phone] Fax No.:Primary Phone No.;[phone] ext. 3125 Fax No.:
Secondary Phone No.:Secondary Phone No.:
Email Address: mrslamon®hsmsoIutions.com Email Address:zcamachotShsmsolutions.com
APPLICATION IS BEING MADE FOR
C New Non-permitted Facility/Greenfield □Modification of Facility (permitted)Q Renewal Title V G3 Renewal Non-Title V
O Name Change □ Ownership Change □Administrative Amendment □ Renewal wth ModiHcation
FACILITY CLASSIFICATION AFTER APPLICATION (Check Only One)
□ General S Small □ Prohibitory Small □ Synthetic Minor □Title V
FACILITY INFORMATION
Describe nature of (plant site) operation(s):
Polystyrene foam product manufacturing
Facility ID No. 0200083
Primary SIC/NAICS Code: 3086 / 32614 Current/Previous Air Permit No. 08502R04 Expiration Date: March 31, 2024
FACILITY LOCATION:Latitude: 35d 54.0973m Longitude: 81d 5.3202m
Does this application contain ^
confidential data?YES Q '^if yes, please contact the DAQ Regional Office prior to submitting this application."'*
(See Instructions)
PERSON OR FIRM THAT PREPARED APPUCATION
Person Name: Kim Teofiiak Firm Name:Trinity Consultants, Inc.
Mailing Address Line 1: 325 Arlington Avenue Mailing Address Line 2:Suite 500
City: Charlotte Slate:NC Zip Code:28203 County:Mecklenburg
Phone No.: [phone] Fax No.: [phone] Email Address:kteofiiaktaitrlnitvconsultants.com
SIGNATURE OF RESPONSIBLE OFFICIAL/AUTHORIZED CONTACT
Name (typed); Mr. Joseph Edwards Title: Director Home Furnishings Ops
X Signature (Blue Ink): - -IP la
Ca,'■^/o NO DEPARTMENT OF
r Attach Additional Sheets As Necessary ENvlRONMENTAL|QiiALl|TYr oreceivei5^^^
DEC 1 8 2023
MOORESVILLE REGIONAL OFFICE
DIVISION OF AIR QUALITY
FORM A (continued, page 2 of 2)
GENERAL FACILITY INFORMATION
REVISED 03/03/23 NCDEQ/Divlsion of Air Quality - Application for Air Permit to Construct/Operate
SECTION AA1 - APPUCATION FOR NON-TITLE V PERMIT RENEWAL
Hickory Springs Manufacturing Company (Company Name) hereby formally requests renewal of Air Permit No. 08502R04
There have been no modifications to the originally permitted facility or the operations therein that would require an air permit since the last permit was issued.
Is your facility subject to 40 CFR Part 68 "Prevention of Accidental Releases" - Section 112(r) of the Clean Air Act? LI YES (3 NO
if yes, have you already submitted a Risk Management Plan (RMP) to EPA? D YES D NO Date Submitted:
Did you attach a cument emissions inventory? □ YES □ NO
If no. did you submit the inventory via AERO or by mail? q] Via AERO □ Mailed Date Mailed:
SECTION AA2 - APPLICATION FOR TITLE V PERMIT RENEWAL
In accordance with the provisions of Title 15A 20 .0513, the responsible official of (Company Name)
hereby formally requests renewal of Air Permit No. (Air Permit No.) and further certifies that:
(1) The current air quality permit identifies and describes all emissions units at the above subject facility, except where such units are exempted under the North
Carolina Title V regulations at 15A NCAC 20 .0500;
(2) The current air quality permit cites all applicable requirements and provides the method or methods for determining compliance with the applicable requirements:
(3) The facility is currently in compliance, and shall continue to comply, with all applicable requirements. (Note; As provided under ISA NCAC 20 .0512,
compliance with the conditions of the permit shall be deemed compliance with the applicable requirements specifically identified in the permit);
(4) For applicable requirements that become effective during the term of the renewed permit that the facility shall comply on a timely basis;
(5) The facility shall fulfill applicable enhanced monitoring requirements and submit a compliance certification as required by 40 CFR Part 64.
The responsible official (signature on page 1) certifies under the penalty of law that all information and statements provided above, based on information and belief formed after
reasonable inquiry, are true, accurate, and complete.
SECTION AA3 - APPLICATION FOR NAME CHANGE
New Facility Name:
Former Facility Name:
An official facility name change is requested as described above for the air permit mentioned on page 1 of this form. Complete the other sections if there have been
modifications to the originally permitted facility that would require an air quality permit since the last permit was issued and if there has been an ownership change associated
with this name change.
SECTION AA4 - application FOR AN OWNERSHIP CHANGE
By this application we hereby request transfer of Air Quality Permit No. from the former owner to the new owner as described below.
The transfer of permit responsibility, coverage and liability shall be effective Immediately (or insert date). The legal ownership of the
facility described on page 1 of this form has been, or will be. transferred on (date). There have been no modifications to the originally
permitted facility that would require a permit since the last permit was issued
Signature of New (Buyer) Responsible Official/Authorized Contact {as typed on page 1):
X Signature (Blue Ink): Date:
New Facility Name:
Former Facility Name:
Signature of Former (Seiier) Responsible Official/Authorized Contact:
Name (t^ed or print):
Title:
X Signature (Blue Ink): Date:
Former Legal Corporate/Owner Name:
In lieu of the seller's signature on this form, a letter may be submitted with the seller's signature indicating the ownership change
SECTION AA5 - APPLICATION FOR ADMINISTRATIVE AMENDMENT
Describe the requested administrative amendment here (attach additional documents as necessary):
Attach Additional Sheets As Necessary Page 2 of 2
FORMS A2, A3
EMISSION SOURCE LISTING FOR THIS APPLICATION
112r APPLICABILITY INFORMATION- A3
A2
REVISED 09/22/16 NCDEQ/Dlvision of Air Quality - Application for Air Permit to Construct/Operate A2
EMISSION SOURCE LISTING: New, Modified, Previously Uripermitted, Replaced, Deleted
EMiSSiON SOURCE
ID NO.
EMISSION SOURCE
DESCRIPTION
CONTROL DEVICE
ID NO.
CONTROL DEVICE
DESCRIPTION
i.:"' \,_ _:^;iEc|Ui[jm^t To Be ADDED By This Appli(:atibn;(New,:Previously Unpermitted, or RepiacerhenQ '^ y J ;
Existing Permitted Equipment To Be MODIFIED By This Application
Equipment To Be DELETED By This Application
112(r) APPLICABILITY INFORMATION A3
Is your facility subject to 40 CFR Part 68 "Prevention of Accidental Releases" - Sect
If No, please specify in detail how your facility avoided applicability;
regulated materials In quantities exceeding the reguiatory threshold.
Ion 112(r) of the Federal Clean Air Act? □ Yes 0 No
The Hickory Springs Hiddenite faciiity does not store
If yourfacility Is Subject to 1 l2(r), please complete the following:
A. Have you already submitted a Risk Management Plan (RMP) to EPA Pursuant to 40 CFR Part 68.10 or Part 68.150?
n Yes n No Specify required RMP submlttal date: If submitted. RMP submittal date:
B. Are you using administrative controls to subject your facility to a lesser 112(r) program standard?
□ Yes □ No If yes, please specify:
C. List the processes subject to 112(r) at yourfacility: .
PROCESS DESCRIPTION
PROCESS LEVEL
(1,2, or 3)H/\ZARDOUS CHEMICAL
MAXIMUM INTENDED
INVENTORY (LBS)
Attach Additional Sheets As Necessary