AQ_F_0400047_20160512_CMPL_InspRpt

NORTH CAROLINA DIVISION OF Fayetteville Regional Office
AIR QUALITY B.V. Hedrick Gravel and Sand Company
NC Facility ID 0400047
Inspection Report County/FIPS:Anson/007
Date: 05/24/2016
Facility Data Permit Data
B.V.Hedrick Gravel and Sand Company Permit 09572/R04
403 Gravel Plant Rd. Issued 6/10/2015
Lilesville,NC 28091 Expires 5/31/2023
Lat: 34d 56.7302m Long: 79d 55.8806m Classification Synthetic Minor
SIC: 1442/Construction Sand And Gravel Permit Status Active
NAICS: 212321 /Construction Sand and Gravel Mining Current Permit Application(s)None
Contact Data Program Applicability
Facility Contact Authorized Contact Technical Contact SIP
Timothy Jones Danny Settle Jason Conner MACT Part 63: Subpart ZZZZ
Superintendent President-Eastern Environmental Director NSPS: Subpart IIII,Subpart 000
[phone] Division [phone]
[phone]
Compliance Data
Comments:
Inspection Date 05/12/2016
Inspector's Name Mike Thomas
J Inspector's pgna ure: � Operating Status Operating
j ( Compliance Code Compliance-inspection
7-K7 Action Code FCE
Date of Signature: On-Site Inspection Result Compliance
r ZY--&
Total Actual emissions in TONS/YEAR:
TSP S02 NOX VOC CO PM10 *HAP
2014 --- --- --- --
2009 0.0400 0.0200 0.3100 0.0300 0.0700 0.0300 0.1670
' *Highest HAP Emitted(in ounds)
Five Year Violation History:None
Date Letter Tyne Rule Violated Violation Resolution Date
Performed Stack Tests since last FCE:None
Date Test Results Test Method(s) Source(s)Tested
I
1) Location/Directions
B.V.Hedrick Gravel and Sand is located at 403 B.V. Hedrick Gravel Plant Road, off Hwy 74 East near
Lilesville,NC, in Anson County. From Rockingham,take HWY 74 west. B.V. Hedrick is approximately 3.5
miles past where HWY 74 crosses the Pee Dee River. Proceed down the dirt road. The office/scale house is
the light colored building on the right. Be mindful of truck traffic.
I
i

2) Safety Considerations
Standard DAQ safety equipment, as well as safety vest. Watch for trains at the railroad tracks just before
entering property, as well as large trucks and loaders while on site.
3) Facility and General Description
B.V.Hedrick Sand and Gravel is a granite mining operation. This facility is permitted under Air Permit No.
09572R04,effective 10 June 2015 until 31 May 2023.Mike Thomas conducted the last inspection on 3
June 2015.
B.V. Hedrick Gravel and Sand Company is a mining facility that primarily produces sand for
commercial use and is permitted for crushing gravel. This facility is a quarry which extracts mainly
granite from the earth.The granite and crushed stone products are loosened by drilling and blasting,
and then are loaded by power shovel or front-end loader into large haul trucks that transport the
material to the processing operations. Primary operations include a jaw,which is used for initial
crusher reduction,and a series of conveyors. This crusher product is next fed through a grizzly feeder
for undersize material, and then is discharged onto a conveyor,where it goes through more screening
processes, until it is conveyed to a surge pile for temporary storage or sold as coarse aggregate. The
finest product is sold to customers,who then bag and sell the"sand,"which is used mainly in small
aquariums. Crushers, conveyors and power screens are all electric,with generators powered by diesel
engines. There are no emergency generators.
The bulk of activity at the site is related to B.V.Hedrick's sand mining operation. The sand mining
operation does not require an Air Permit. All sand operations are water-suppressed.
This facility has not conducted any operations or operated any of the permitted sources since the very end of i
2012.
4) Permitted Emission Sources
Crushing and Feeding Operations Wet suppression water
Crushers(NSPS) -... VJ9
Not Operating spray system
WS Screens(NSPS) Screening Operations Wet suppression water
Not Operating spray system
Conveying Operations Wet suppression water
Conveyors(NSPS) WS
Not Operating spray system
_ — I
Aztec G 1 125 HP John Deere diesel generator
(NSPS,NESHAP) (manufactured in 2008)
Not Operating
C50 G4 350 HP Tier II Caterpillar diesel generator I
(NSPS,NESHAP) (manufactured in 2009) N/A N/A
Not Operating
365 HP Caterpillar diesel generator
T-GIO F (NESHAP) (manufactured in 2002)
Not Operating
M 60 l00 HP Caterpillar diesel generator

E� Sl�i;use y
t
(NESHAP) (manufacturedNot Operating 01)
5) Inspection Conference
On 12 May 2016 I, Mike Thomas, of FRO DAQ conducted a compliance inspection of the B.V.
Hedrick Gravel and Sand Company. I met with Tim Jones, Plant Superintendent and Facility
Contact. We discussed the following:
i
a) Verified the FACFINDER. No changes are necessary.
I
b) I discussed plant operations with Mr. Jones. He stated again that the facility intends to keep
their air permit active but the company has no intention of re-starting gravel mining
operations in the foreseeable future.
c) Production
Year Crushed Stone T/ r
2015 0
2014 0
2013 0
2012 31,320
6) Inspection Summary
Mr.Jones led me on a tour of the facility which consisted of driving down to the mine and observing
that no mining operations are taking place. We then drove around to see that the generators are still
in storage in the same areas that they were being housed during the last inspection.
Mr.Jones also took me for a quick tour of the sand mining operation. There continues to be no
screens or crushers being utilized in that operation. Wet suppression is being used for the sand
mining operation and I observed no issues with dust coming from the mine or the travel ways.
7) Permit Stipulations
a) A.2 2Q.0304 PERMIT RENEWAL AND EMISSION INVENTOR Y REQUIREMENT—Entire
facility subject. Submit permit renewal application and EI at least 90 days prior to permit expiration.
Appeared to be in compliance—The facility was due to submit their EI and Permit Renewal by 2 July
i 2015. The facility submitted the EI on 30 March 2015 and permit renewal was received on 1 April
2015.
b) A.3 2D .050l(c)PRODUCTIONRATE LIMITATION—Production shall not exceed the Maximum
Allowable Production Rate of 12,000 tons/day and 4,250,000 tons/year,with a boundary distance b/t
300 and 450 feet; records shall be kept indicating so (indicating daily and monthly quantity).
Appeared to be in compliance—I viewed the logbooks and the total production of crushed stone in 2015
was 0 tons. The facility has not operated since 2012.
c) A.4 2D .0501(c) OUT-OF-PIT DIESEL ENGINE CAPACITYLIMITATION- The cumulative
power output capacity from diesel or fuel oil-fired engines located outside of the quarry pit shall not
exceed the applicable Maximum Power Output Capacity OF 220 horsepower, based on the facility's
boundary distance of between 300 and 450 feet.
Appeared to be in compliance—The facility has not operated since the end of 2012. All generators
onsite are no longer in use and are being housed in storage areas.
i

i
d) A.5 2D .0501(c)EQUIPMENT REPORTING—An equipment list shall be kept on site, showing
compliance with all permitted requirements. The Permittee must notify FRO if equipment changes are
made.
Appeared to be in compliance—A diagram of the permitted equipment list is kept on site in a DAQ
binder, showing the rated capacities,ID numbers, size,and dates. I viewed this list, and it meets all
requirements of this facility's permit.
e) A.6 2D .0510 PARTICULATE CONTROL REQUIREMENT—As required by"Particulates from
Sand, Gravel,or Crushed Stone Operations",this operation shall take measures to reduce particulate
matter from becoming airborne so as to prevent exceeding the ambient air quality standards beyond the
property line for PM; emissions from all operating equipment shall be controlled.
Appeared to be in compliance—Facility has not operated since 2012.
I) A.7 2D .0521 VISIBLE EMISSIONS CONTROL REQUIREMENT-Visible emissions from sources
post 1 July 1971 shall not be more than 20%opacity. r
Appeared to be in compliance—Facility has not operated since 2012.
g) A.8 2D .0524 NEW SOURCE PERFORMANCE STANDARDS(for the processing equipment)-
The Permittee shall comply with all NSPS reporting,testing, and recordkeeping requirements as
promulgated in 40 CFR 60, Subpart 000.
Appeared to be in compliance—DAQ FRO received notification of initial start up of its equipment on 3
December 2009(start-up date was 18 November 2009,but facility did not achieve maximum production
rate until September 2010);the facility has not operated since the end of 2012.
C
h) A.9 2D .0524 NEW SOURCE PERFORMANCE STANDARDS,Subpart Ills(for the Compression
Ignition Internal Combustion Engines Generators(Aztec G-I and C50-G41)—The Permittee shall
comply with all NSPS reporting,testing, and requirements as promulgated in 40 CFR 60 Subpart IIII;
applicable sources are the generators constructed after 1 April 2006; compliance includes: (1)purchase
of a 2007 model or later CI ICE and ensuring that it is emissions-compliant and keeping records of all
manufacturing data(indicating compliance);(2) diesel fuel used shall be< .05% S through 1 October
2010 and< .0015% S thereafter; (3) installation of a non-resettable hour meter;(4)record hours of
engine operation; (5) submit a semi-annual report that includes monthly and 12-month operation hours.
Appeared to be in compliance-Generators have not been operated since the end of 2012. I verified that
each generator on site has a non-resettable hour meter. Logbook showed entries for hours of use when the
generators were last operated, and the facility submitted its semi-annual report on time and in compliance.
i) A.10 2D .0535 NOTIFICATION REQUIREMENT- The facility is required to notify DAQ if excess
emissions occur for more than a 4-hour period caused by a breakdown or other abnormal condition.
Appeared to be in compliance—The facility has not operated since the end of 2012.
j) A.11 2D .0540(e)(1) FUGITIVE DUST CONTROL PLAN—The Permittee shall have a DAQ
approved written fugitive dust control plan to minimize dust emissions from fugitive sources.
Appeared to be in compliance—Facility submitted a fugitive dust control plan that was approved by DAQ
on 16 October 2009. The facility has not operated since the end of 2012. I observed no fugitive dust from the
adjacent sand mining operation during my inspection.
k) A.12 2D .0540 FUGITIVE DUST CONTROL REQUIREMENT—The Permittee shall not cause or
allow fugitive dust emissions to contribute to complaints or excess visible emissions beyond the
Property
Appeared to be in compliance—The facility has not operated since the end of 2012.

1) A.13 2D .0611 NOTIFICATION REQUIREMENT-within 15 days after start-up of any permitted
source at this facility,the Permittee shall NOTIFY, in WRITING,the Regional Supervisor, DAQ, of the
start-up.
Appeared to be in compliance—The facility has not operated since the end of 2012 and they have no
plans to re-start any operations in the foreseeable future according to Mr. Jones.
m)A.14 2D .1111, 40 CFR 63, Subpart ZZZZ NATIONAL EMISSIONSTANDARDS FOR
HAZARDOUS AIR POLL UTANTS FOR STATIONARY RECIPROCATING INTERNAL
COMBUSTIONENGINES—Applicable to new sources(if commenced construction on or after 12
June 2006); installed generators must have manufacturing data showing emissions compliance, and
facility must keep records of maintenance and operating hours;the Permittee shall comply with all
notification,testing, and monitoring requirements; compliance date would be upon start-up.
Appeared to be in compliance—The facility has not operated these generators since the end of 2012.
n) A.15 2D .I I I I MAXIMUMACHIEVABLE CONTROL TECHNOLOGY-for the Generator(ID No.
T-G10),which is considered an existing,non-emergency,non-black start,compression ignition(CI)
reciprocating internal combustion engine(RICE) greater than 300 brake horsepower and less than or
equal to 500 brake horsepower,the Permittee shall comply with all notification,testing, and monitoring
requirements; compliance date would be upon start-up.
Appeared to be in compliance—The facility has not operated this generator since the end of 2012.
o) A.16 2D .1111 MAXIMUMACITIEVABLE CONTROL TECHNOLOGY-For the 125 HP John
Deere diesel generator(ID No. Aztec G-1) and 350 HP Tier 11 Caterpillar generator(ID No. C50 G4),
classified as new stationary RICE located at an area source of HAP emissions,the Permittee shall
comply with all applicable provisions, including the notification,testing, reporting,recordkeeping, and
monitoring requirements contained in Environmental Management Commission Standard 15A NCAC
2D .1111, as promulgated in 40 CFR 63, Subpart ZZZZ- "National Emissions Standards for Hazardous
Air Pollutants for Stationary Reciprocating Internal Combustion Engines," including Subpart A
"General Provisions."
Appeared to be in compliance—The facility has not operated these generators since the end of 2012.
p) A17 2Q .0304 ZONING SPECIFIC REQUIREMENT-Permittee shall comply with all lawfully
adopted local ordinances that apply to the facility at the time of construction or operation of the facility.
The local zoning authority shall have the responsibility of enforcing all lawfully adopted local zoning or
subdivision ordinances.
Appears to be in compliance—A Certificate of Zoning Compliance from Anson County was
submitted with the permit application.
q) A.18 2Q .0315 LIMITATION TO AVOID ISA NCAC 2Q.050I FOR SYNTHETICMINOR
FACILITIES—Facility-wide NOx emissions shall be less than 100 tons per each 12-month period,and
facility shall keep records indicating so.
Appeared to be in compliance—Facility keeps a logbook with monthly NOx emission entries for all
generators when operating. 2015 NOx emissions were 0.
8) 112R Status
This facility neither uses nor stores chemical compounds that require a written risk management plan under the
Clean Air Act, Section 112R.
9) Non-compliance History Since 2010
There have been no prior DAQ violations in this facility's permitted history.

10) Comments and Compliance Statement
The facility has not operated since 2012. B.V. Hedrick has no plans to reopen the mining operation in the
foreseeable future.
B.V.Hedrick Gravel& Sand Company appeared to be in compliance on 12 May 2016.
Pink sheet:No comments.
/mst
r
i
t
i
1