18015_ Craighead Rd VMP-Approval 20170524

State of North Carolina | Environmental Quality | Waste Management
1646 Mail Service Center | 217 West Jones Street | Raleigh, NC 27699-1646
919 707 8200 T

May 24, 2017

Sent Via Email [e-mail]

Mr. Trinh DeSa, PE
Hart & Hickman
2923 South Tryon Street, Suite 100
Charlotte, NC 28203

Subject: Approval of Vapor Mitigation System
Craighead Rd (Abernathy Lumber)
Charlotte, Mecklenburg County
Brownfields Project Number 18015-14-60

Dear Mr. DeSa:

The North Carolina Department of Environmental Quality (DEQ) Brownfields Program
received an electronic submittal of the revised Vapor Mitigation Plan dated May 23, 2017 for the
above referenced Brownfields Property. This plan was submitted in accordance with the
recorded Notice of Brownfields Property Land Use Restriction Number 4. DEQ approves the
vapor mitigation plan of a vapor liner and active mitigation system for the redevelopment.

Be advised that this approval from the Brownfields Program does not waive any
applicable requirement to obtain any necessary permits, licenses or certifications for the above
listed activities nor does it waive any requirement to comply with applicable law for such
activities. If you have questions about this correspondence or require additional information,
please contact me by phone at 704/661-0330, or by e-mail at [e-mail].

Sincerely,

Carolyn Minnich
Carolyn Minnich
Brownfields Project Manager
Division of Waste Management

ec: [e-mail]
[e-mail]
[e-mail]

1

S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\VMP - Noda
Village_revision 1.doc
Vapor Mitigation Plan – Revision 1
Craighead Road (Abernethy Lumber)
E. Craighead Road & Philemon Avenue
Charlotte, North Carolina
Brownfields Project Number: 18015-40-060
H&H Job No. SHR-001

H&H has prepared this vapor mitigation plan (VMP) for installation of a vapor liner and active
vapor mitigation system (hereafter referred to as the mitigation system) as part of a multi-unit
residential development at the NoDa Village Apartment Community known as the Craighead
Road (Abernethy Lumber) Brownfields site (Brownfields Project # 18015-40-060) located at the
intersection of East Craighead Road and Philemon Avenue in Charlotte, Mecklenburg County,
North Carolina. VMP specifications for Building 1 and Building 2, and section details are
included herein as Sheet VMP-1, VMP-2, VMP-3, respectively, and will be used to guide
construction of the mitigation system. The VMP includes installation of a vapor liner and active
sub-slab depressurization to reduce the potential for vapor intrusion into occupied portions of the
development under both Building 1 and Building 2. Vapor liner characteristics are specified to
meet the commonly accepted criteria for a liner to be termed a “vapor barrier”. The mitigation
system specifications on Sheet VMP-3 includes an example (Stego ® Wrap Vapor Barrier) of a
15-mil liner which meet these criteria, and specifications sheets for the example vapor barrier is
included herein.

Sub-slab depressurization will be accomplished using electric vacuum fans and poly-vinyl
chloride (PVC) vapor collection/conveyance piping which will collect vapor from the sub-slab
aggregate and discharge the vapor through exhaust stacks above the building roof. The sub-slab
aggregate will consist of high permeability stone (such as #57 or #67 stone) placed around the
slotted PVC pipe in order to enhance sub-slab vapor transmission and collection effectiveness.
The mitigation system includes RadonAway® Model RP145 vacuum fans installed on the
building roof. A fan specification/sales sheet and installation instructions for the RP Series fans
obtained from RadonAway® are included herein. Please note that an equivalent electric vacuum
fan approved by the engineer may also be used by the installation contractor. The fans must be
continuously operated while the building is utilized for residential purposes.
2

S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\VMP - Noda
Village_revision 1.doc
H&H shall perform inspections of the mitigation system installation including, but not limited to,
horizontal collection pipe placement, vapor barrier installation, and vacuum fan hook-up to
vertical risers, during various phases of construction by or under supervision of the engineer
certifying the report. The inspections will include photographs of the mitigation system
construction which will be submitted to the North Carolina Department of Environmental
Quality (DEQ) Brownfields Program in summary reports. The general construction contractor
shall notify H&H of the construction status related to the mitigation system in a timely manner in
order for H&H to perform the required inspections.

Further, H&H will perform pilot tests of the installed mitigation system after the building
concrete slab is in-place and prior to above grade construction. The pilot tests will be performed
to test the effectiveness of the mitigation system design prior to completion of the building.
H&H will use a similar vapor fan (Model RP145, or similar) to extract vapors from the existing
vertical riser pipes and will measure vacuum influence from below the concrete slab using
existing vapor monitoring points and, if needed, will install temporary vapor monitoring points
which will be abandoned following the pilot tests.

Following completion of the mitigation system, on a quarterly basis for the first year, and on an
annual basis thereafter, unless otherwise approved by the DEQ, sub-slab pressure will be
measured relative to indoor air at sub-slab pressure measuring points using a manometer to
demonstrate that the mitigation system is effectively depressurizing the sub-slab. The
approximate locations of the sub-slab pressure measuring points are shown on Sheet VMP-1 and
Sheet VMP-2, and a cut sheet for the floor cleanout, which will be installed at each measuring
point, is included herein. Please note that an air-tight pressure measurement adaptor with hose
barb will be fit into the cleanout by personnel collecting the measurements.

Following completion of the building and during occupancy, the building staff shall perform a
monthly operational and maintenance (O&M) check on the vapor fans to ensure proper operation
and function. Inoperable or damaged fans, or other deficiencies related to the mitigation system
discovered during the O&M visits shall be immediately reported to H&H. The O&M checks
3

S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\VMP - Noda
Village_revision 1.doc
will be recorded on the Vapor Mitigation Monthly Fan O&M Form which is included herein.
These forms shall be submitted to the DEQ on an annual basis. After the first year of operation,
an evaluation of the system operation may be conducted to reduce the frequency of O&M
checks. Any changes to the O&M procedures will need approval from the engineer and the DEQ
Brownfields Program.

Following confirmation that the mitigation system is installed and operating properly, a North
Carolina Professional Engineer (PE)-certified report documenting installation of the mitigation
system, including the results of the inspections and pilot tests, will be submitted to the DEQ
Brownfields Program.
2" x 2" SCH 40 PVC 90DEGREE ELBOW (TYPICAL)SOLID TO SLOTTED 2" SCH 40 PVCPIPE TRANSITION (TYPICAL)
2
"

x

2
"

x

2
"

S
C
H

4
0

P
V
C

T
E
E
(
T
Y
P
I
C
A
L
)
2" PVC VENT PIPE PROTECTION SCREEN(TYPICAL AT ENDS OF SLOTTED PIPE)
2
"

P
V
C

V
E
N
T

P
I
P
E

P
R
O
T
E
C
T
I
O
N

S
C
R
E
E
N
(
T
Y
P
I
C
A
L

A
T

E
N
D
S

O
F

S
L
O
T
T
E
D

P
I
P
E
)
P
O
S
I
T
I
O
N

V
E
R
T
I
C
A
L

R
I
S
E
R

F
1
-
3

W
I
T
H
I
N
T
O
I
L
E
T

W
A
L
L

O
F

M
E
N
S

B
A
T
H
R
O
O
M

O
N
G
R
O
U
N
D

F
L
O
O
R
.

P
O
S
I
T
I
O
N

V
E
R
T
I
C
A
L
R
I
S
E
R

T
O

E
X
T
E
N
D

T
H
R
O
U
G
H

B
A
T
H
R
O
O
M
O
R

T
E
N
A
N
T

S
E
P
A
R
A
T
I
O
N

W
A
L
L

F
O
R
U
P
P
E
R

F
L
O
O
R
S
.
P
O
S
I
T
I
O
N

V
E
R
T
I
C
A
L

R
I
S
E
R

F
1
-
1
W
I
T
H
I
N

B
A
T
H
R
O
O
M

W
A
L
L
.

P
O
S
I
T
I
O
N
V
E
R
T
I
C
A
L

R
I
S
E
R

T
O

E
X
T
E
N
D
T
H
R
O
U
G
H

B
A
T
H
R
O
O
M

O
R

T
E
N
A
N
T
S
E
P
A
R
A
T
I
O
N

W
A
L
L

F
O
R

U
P
P
E
R
F
L
O
O
R
S
.
3
"

T
O

2
"

S
C
H

4
0

P
V
C
R
E
D
U
C
E
R

(
T
Y
P
I
C
A
L
)
F
1
-
2
1
F
1
-
2
0
F
1
-
1
9
F
1
-
1
8
F
1
-
1
7
F
1
-
1
6
F
1
-
1
5
F
1
-
1
3
F
1
-
1
2
F
1
-
1
4
F
1
-
1
1
F
1
-
1
0
F
1
-
9
F
1
-
8
F
1
-
7
F1-5
F
1
-
6
F1-4 F1-2 F1-1F1-32" PVC VENT PIPE PROTECTIONSCREEN (TYPICAL AT ENDS OFSOLID PIPE CONNECTORS)
2
"

x

2
"

x

2
"

S
C
H

4
0

C
R
O
S
S
T
E
E

(
T
Y
P
I
C
A
L
)
2
"

P
V
C

V
E
N
T

P
I
P
E

P
R
O
T
E
C
T
I
O
N
S
C
R
E
E
N

(
T
Y
P
I
C
A
L

A
T

E
N
D
S

O
F
S
O
L
I
D

P
I
P
E

C
O
N
N
E
C
T
O
R
S
)
3"3"3"3"3"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
L
O
C
A
T
E

V
E
R
T
I
C
A
L

R
I
S
E
R
F
1
-
1
7

W
I
T
H
I
N

T
O
I
L
E
T

O
R
S
H
O
W
E
R

W
A
L
L
L
O
C
A
T
E

V
E
R
T
I
C
A
L

R
I
S
E
R
F
1
-
1
2

I
N

K
I
T
C
H
E
N

B
U
I
L
D
-
O
U
T
B
E
H
I
N
D

P
A
N
T
R
Y
POSITION PRESSURE MEASURINGPOINT WITHIN HALLWAY
P
O
S
I
T
I
O
N

P
R
E
S
S
U
R
E

M
E
A
S
U
R
I
N
G
P
O
I
N
T

W
I
T
H
I
N

H
A
L
L

(
O
P
E
N
)

A
R
E
A
O
F

S
T
A
I
R
W
E
L
L
POSITION P
R
E
S
S
U
R
E

M
E
A
S
U
R
I
N
G
POINT WITHI
N

H
A
L
L

(
O
P
E
N
)

A
R
E
A
OF

S
T
A
I
R
W
E
L
L
V
A
P
O
R

M
I
T
I
G
A
T
I
O
N

S
Y
S
T
E
M
D
E
T
A
I
L
S

&

S
P
E
C
I
F
I
C
A
T
I
O
N
S
R
E
V
I
S
I
O
N

1
M
A
Y

1
9
,

2
0
1
7
3
7
3
6

W
i
n
t
e
r
f
i
e
l
d

R
o
a
d
,

S
u
i
t
e

1
0
2
M
i
d
l
o
t
h
i
a
n
,

V
i
r
g
i
n
i
a

2
3
1
1
3
T
e
l
e
p
h
o
n
e

8
0
4
.
2
2
5
.
0
2
1
5
w
w
w
.
2
p
a
.
n
e
t
N
C

F
I
R
M

#
5
1
9
7
2
©

2
0
1
6

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
D
r
a
w
i
n
g
s

a
n
d

s
p
e
c
i
f
i
c
a
t
i
o
n
s

a
r
e

a
n
d

s
h
a
l
l

r
e
m
a
i
n

t
h
e
p
r
o
p
e
r
t
y

o
f

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C

a
n
d

s
h
a
l
l

n
o
t
b
e

u
s
e
d

o
r

r
e
p
r
o
d
u
c
e
d

i
n

w
h
o
l
e

o
r

p
a
r
t

i
n

a
n
y

f
o
r
m
w
i
t
h
o
u
t

p
r
i
o
r

w
r
i
t
t
e
n

c
o
n
s
e
n
t

o
f

P
o
o
l
e

&

P
o
o
l
e
A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
.
D
r
a
w
i
n
g

T
i
t
l
e
:
V
M
P
-
1
2
9
2
3

S
o
u
t
h

T
r
y
o
n

S
t
r
e
e
t
-
S
u
i
t
e

1
0
0
C
h
a
r
l
o
t
t
e
,

N
o
r
t
h

C
a
r
o
l
i
n
a

2
8
2
0
3
7
0
4
-
5
8
6
-
0
0
0
7
(
p
)

7
0
4
-
5
8
6
-
0
3
7
3
(
f
)
L
i
c
e
n
s
e

#

C
-
1
2
6
9

/

#
C
-
2
4
5

G
e
o
l
o
g
y
V
a
p
o
r

M
i
t
i
g
a
t
i
o
n

P
l
a
n

P
r
e
p
a
r
e
d

B
y
:
P
R
O
F
E
S
S
I
O
N
A
L

A
P
P
R
O
V
A
L
NODA VILLAGE
an Apartment Community by
PHILEMON NODA PARTMERS, LLC
at 327 EAST CRAIGHEAD, Charlotte, North Carolina 28206
LEGENDLOCATION OF VERTICAL RISER AND APPROXI
M
A
T
E

L
O
C
A
T
I
O
N

O
F

V
A
C
U
U
M

F
A
N

O
N
BUILDING ROOF (SEE SPECIFICATION #3 AND
D
E
T
A
I
L

1
1

O
N

S
H
E
E
T

V
M
P
-
3
)

A
N
D

F
A
N
NUMBER2" DIA SOLID SCH 40 PVC PIPE (UNLESS SPECIFI
E
D

A
S

3
"

D
I
A
)
2" DIA SLOTTED SCH 4O PVC PIPE (SEE SPECIFI
C
A
T
I
O
N

2

O
N

S
H
E
E
T

V
M
P
-
3
)
SUB-SLAB PRESSURE MEASURING POINT (SOLID

B
L
U
E

L
I
N
E

I
N
D
I
C
A
T
E
S

E
X
T
E
N
D
E
D

I
N
T
A
K
E

L
I
N
E
;
REFER TO DETAILS 8 AND 9 ON SHEET VMP-3)GROUND FLOOR SLAB STEP (HEIGHT VARIES)NOTES:1.FOR DETAIL CALL-OUTS 5 AND 6, ALSO REFER TO DETAIL 11 AND

S
P
E
C
I
F
I
C
A
T
I
O
N

3
ON SHEET VMP-32.GROUND FLOOD SLAB DESIGN INCLUDES POST-TENSION CABLE
S
.
3.FOUNDATION PLAN AND DETAILS PROVIDED BY POOLE & POOL
E

A
R
C
H
I
T
E
C
T
U
R
E

O
F
MIDLOTHIAN, VA AND DAVIS & CHURCH STRUCTURAL ENGINEE
R
S

O
F

A
P
L
H
A
R
E
T
T
A
,
GA AND ARE SUBJECT TO COPYRIGHT PROTECTION.F1-1S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\Revised - 03202017\Figures\NDS1.1_H&H_rev051917.dwg, S1.1a Building 1 - Partial Foundation Plan, 5/23/2017 2:55:44 PM, TDeSa
F
2
-
1
2
F
2
-
1
1
F
2
-
1
0
F
2
-
9
F
2
-
8
3
"
F
2
-
7
F
2
-
6
F
2
-
5
F
2
-
4
F
2
-
3
F2-2 F2-12" x 2" SCH 40 PVC 90DEGREE ELBOW (TYPICAL)SOLID TO SLOTTED 2" SCH 40 PVCPIPE TRANSITION (TYPICAL)
2
"

x

2
"

x

2
"

S
C
H

4
0

P
V
C

T
E
E
(
T
Y
P
I
C
A
L
)
2" PVC VENT PIPE PROTECTION SCREEN(TYPICAL AT ENDS OF SLOTTED PIPE)
3
"

T
O

2
"

S
C
H

4
0

P
V
C
R
E
D
U
C
E
R

(
T
Y
P
I
C
A
L
)
2
"

P
V
C

V
E
N
T

P
I
P
E

P
R
O
T
E
C
T
I
O
N
S
C
R
E
E
N

(
T
Y
P
I
C
A
L

A
T

E
N
D
S

O
F
S
O
L
I
D

P
I
P
E

C
O
N
N
E
C
T
O
R
S
)
2
"

x

2
"

x

2
"

S
C
H

4
0

C
R
O
S
S
T
E
E

(
T
Y
P
I
C
A
L
)
3"3"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
3
"
P
O
S
I
T
I
O
N

V
E
R
T
I
C
A
L

R
I
S
E
R

F
2
-
8
W
I
T
H
I
N

T
O
I
L
E
T

O
R

S
H
O
W
E
R

W
A
L
L
P
O
S
I
T
I
O
N

V
E
R
T
I
C
A
L

R
I
S
E
R

F
2
-
1
2

I
N
T
E
N
A
N
T

W
A
L
L
,

N
O
T

I
N

S
T
A
I
R
W
E
L
L
C
O
O
R
D
I
N
A
T
E

V
E
R
T
I
C
A
L

R
I
S
E
R

F
2
-
5
P
O
S
I
T
I
O
N

I
N

S
I
N
K

W
A
L
L

O
F

U
N
I
T

B
3

F
O
R
U
P
P
E
R

F
L
O
O
R
S

(
R
I
S
E
R

L
O
C
A
T
I
O
N

M
A
Y
B
E

A
D
J
U
S
T
E
D

I
N

F
I
E
L
D
)
POSITION VERTICAL RISER F2-2WITHIN BATHROOM WALL
V
A
P
O
R

M
I
T
I
G
A
T
I
O
N

S
Y
S
T
E
M
D
E
T
A
I
L
S

&

S
P
E
C
I
F
I
C
A
T
I
O
N
S
R
E
V
I
S
I
O
N

1
M
A
Y

1
9
,

2
0
1
7
3
7
3
6

W
i
n
t
e
r
f
i
e
l
d

R
o
a
d
,

S
u
i
t
e

1
0
2
M
i
d
l
o
t
h
i
a
n
,

V
i
r
g
i
n
i
a

2
3
1
1
3
T
e
l
e
p
h
o
n
e

8
0
4
.
2
2
5
.
0
2
1
5
w
w
w
.
2
p
a
.
n
e
t
N
C

F
I
R
M

#
5
1
9
7
2
©

2
0
1
6

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
D
r
a
w
i
n
g
s

a
n
d

s
p
e
c
i
f
i
c
a
t
i
o
n
s

a
r
e

a
n
d

s
h
a
l
l

r
e
m
a
i
n

t
h
e
p
r
o
p
e
r
t
y

o
f

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C

a
n
d

s
h
a
l
l

n
o
t
b
e

u
s
e
d

o
r

r
e
p
r
o
d
u
c
e
d

i
n

w
h
o
l
e

o
r

p
a
r
t

i
n

a
n
y

f
o
r
m
w
i
t
h
o
u
t

p
r
i
o
r

w
r
i
t
t
e
n

c
o
n
s
e
n
t

o
f

P
o
o
l
e

&

P
o
o
l
e
A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
.
D
r
a
w
i
n
g

T
i
t
l
e
:
V
M
P
-
2
2
9
2
3

S
o
u
t
h

T
r
y
o
n

S
t
r
e
e
t
-
S
u
i
t
e

1
0
0
C
h
a
r
l
o
t
t
e
,

N
o
r
t
h

C
a
r
o
l
i
n
a

2
8
2
0
3
7
0
4
-
5
8
6
-
0
0
0
7
(
p
)

7
0
4
-
5
8
6
-
0
3
7
3
(
f
)
L
i
c
e
n
s
e

#

C
-
1
2
6
9

/

#
C
-
2
4
5

G
e
o
l
o
g
y
V
a
p
o
r

M
i
t
i
g
a
t
i
o
n

P
l
a
n

P
r
e
p
a
r
e
d

B
y
:
P
R
O
F
E
S
S
I
O
N
A
L

A
P
P
R
O
V
A
L
NODA VILLAGE
an Apartment Community by
PHILEMON NODA PARTMERS, LLC
at 327 EAST CRAIGHEAD, Charlotte, North Carolina 28206
LEGENDLOCATION OF VERTICAL RISER AND APPROXIMATE LOCATION OF VACUUM FA
N

O
N
BUILDING ROOF (SEE SPECIFICATION #3 AND DETAIL 11 ON SHEET VMP-3) AND
F
A
N
NUMBER2" DIA SOLID SCH 40 PVC PIPE (UNLESS SPECIFIED AS 3" DIA)2" DIA SLOTTED SCH 4O PVC PIPE (SEE SPECIFICATION 2 ON SHEET VMP-3)SUB-SLAB PRESSURE MEASURING POINT (SOLID BLUE LINE INDICATES EXTENDED I
N
T
A
K
E

L
I
N
E
.
REFER TO DETAILS 8 AND 9 ON SHEET VMP-3)GROUND FLOOR SLAB STEP (HEIGHT VARIES)F2-1NOTES:1.FOR DETAIL CALL-OUTS 5 AND 6, ALSO REFER TO DETAIL 11 AND SPECIFICATION 3ON SHEET VMP-3.2.GROUND FLOOD SLAB DESIGN INCLUDES POST-TENSION CABLES.3.FOUNDATION PLAN AND DETAILS PROVIDED BY POOLE & POOLE ARCHITECTURE OFMIDLOTHIAN, VA AND DAVIS & CHURCH STRUCTURAL ENGINEERS OF APLHARETTA,GA AND ARE SUBJECT TO COPYRIGHT PROTECTION.S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\Revised - 03202017\Figures\NDS1.2_H&H_rev051917.dwg, S1.2 Building 2 - Foundation Plan, 5/23/2017 2:58:46 PM, TDeSa
VMS VAPOR LINER AND BASE COURSE (TYP)1VMS SLOTTED COLLECTION PIPE (TYP)2 BASE COARSE - CLEAN #57 OR #67 STONE,MIN 4" THICK BENEATH VMS VAPOR LINER VAPOR LINER (SEE SPECIFICATION #1)2" SCH 40 THREADED FLUSH JOINTSLOTTED PVC PIPE (0.020" SLOT WIDTH,1/8" SLOT SPACING) WITH FILTER SOCKSET WITHIN MIN 4" BASE COURSE
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
P
I
P
E

P
E
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
VAPOR LINER (SEE SPECIFICATION #1)
T
O
P

O
F

T
H
I
C
K
E
N
E
D
S
L
A
B

T
U
R
N
D
O
W
N
S
O
L
I
D

P
I
P
E

C
O
N
N
E
C
T
O
R

T
H
R
O
U
G
H

T
H
I
C
K
E
N
E
D

S
L
A
B
CONCRETE FLOOR SLABSUBBASESUBBASE
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D
T
O

P
I
P
E

P
E
R

M
A
N
U
F
A
C
T
U
R
E
R
I
N
S
T
R
U
C
T
I
O
N
S
S
O
L
I
D

T
O

S
L
O
T
T
E
D

2
"

S
C
H

4
0
P
V
C

P
I
P
E

T
R
A
N
S
I
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
S
T
U
D

W
A
L
L
(
N
O
T

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
)
V
A
P
O
R

L
I
N
E
R
B
E
N
E
A
T
H

T
H
I
C
K
E
N
E
D

S
L
A
B
H
O
R
I
Z
O
N
T
A
L

P
I
P
E

T
H
R
O
U
G
H

T
H
I
C
K
E
N
E
D

S
L
A
B
3
V
M
P
-
3
T
O
P

O
F

T
H
I
C
K
E
N
E
D
S
L
A
B

T
U
R
N
D
O
W
N
F
I
R
E

W
A
L
L

(
N
O
T

P
R
E
S
E
N
T
I
N

A
L
L

L
O
C
A
T
I
O
N
S
)
F
L
O
O
R

C
L
E
A
N
O
U
T
,

A
D
J
U
S
T
A
B
L
E
,
2
"

D
I
A

Z
U
R
N

I
N
D
U
S
T
R
I
E
S
M
O
D
E
L

#
C
O
2
4
5
0
-
P
V
2
(
O
R

E
Q
U
I
V
A
L
E
N
T
)
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
P
I
P
E

P
E
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
2
"

S
C
H

4
0

P
V
C

9
0

D
E
G
R
E
E

E
L
B
O
W
2
"

V
E
N
T

P
I
P
E
P
R
O
T
E
C
T
I
O
N

S
C
R
E
E
N

P
R
E
S
S
U
R
E

M
E
A
S
U
R
I
N
G

P
O
I
N
T

V
E
N
T

P
I
P
E
P
R
O
T
E
C
T
I
O
N

S
C
R
E
E
N
NTSNTS
N
T
S
N
T
S
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
N
T
S
H
O
R
I
Z
O
N
T
A
L

P
I
P
E

A
T

S
L
A
B

S
T
E
P
4
N
T
S
V
M
S

V
A
C
U
U
M

F
A
N

A
N
D

E
X
H
A
U
S
T

D
I
S
C
H
A
R
G
E

O
N

R
O
O
F
T
O
P
V
A
R
M
I
N
T

S
C
R
E
E
N
W
E
A
T
H
E
R

P
R
O
O
F

B
O
X
(
H
A
R
D
W
I
R
E

F
A
N
)
3
"

P
V
C

D
U
C
T

P
I
P
E
T
H
R
O
U
G
H

R
O
O
F
R
O
O
F

T
O
P
F
L
E
X
I
B
L
E

C
O
U
P
L
I
N
G
F
L
E
X
I
B
L
E

C
O
U
P
L
I
N
G
V
A
C
U
U
M

F
A
N
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
3
)
3
"

P
V
C

E
X
H
A
U
S
T

D
U
C
T

P
I
P
E
3
"

P
V
C

9
0

D
E
G
R
E
E

E
L
B
O
W
V
M
P
-
3
VMP-3VMP-3
V
E
R
T
I
C
A
L

R
I
S
E
R

A
T

S
L
A
B

P
E
N
E
T
R
A
T
I
O
N

W
I
T
H

T
E
E
5
N
T
S
VA
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
PIPE
P
E
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
3
"

S
C
H

4
0

P
V
C

9
0

D
E
G
R
E
E

T
E
E
S
T
U
D

W
A
L
L
3
"

S
C
H

4
0

P
V
C

R
I
S
E
R

D
U
C
T

P
I
P
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
2
)
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
V
M
P
-
3
N
T
S
V
E
R
T
I
C
A
L

R
I
S
E
R

A
T

I
N
T
E
R
I
O
R

S
L
A
B

S
T
E
P

D
E
T
A
I
L
N
T
S
S
T
U
D

W
A
L
L
(
N
O
T

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
)
1
1
V
M
P
-
3
1
0
V
M
P
-
3
8
V
M
P
-
3
6
V
M
P
-
3
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
3
"

S
C
H

4
0

P
V
C

R
I
S
E
R

D
U
C
T

P
I
P
E
.

P
O
S
I
T
I
O
N
V
E
R
T
I
C
A
L

R
I
S
E
R

P
I
P
E

O
N

H
I
G
H

S
I
D
E

O
F
S
T
E
P
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
2
)
F
I
R
E

W
A
L
L

P
R
E
S
E
N
T

I
N
S
O
M
E

A
R
E
A
S
SOLID TO SLO
T
T
E
D

2
"

S
C
H

4
0

P
V
C
PIPE TRANSITI
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
S
T
U
D

W
A
L
L
VAPO
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
PIPE PE
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
S
O
L
I
D

T
O

S
L
O
T
T
E
D

2
"

S
C
H

4
0

P
V
C
P
I
P
E

T
R
A
N
S
I
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
3
"

S
C
H

4
0

P
V
C

T
E
E
S
O
L
I
D

T
O

S
L
O
T
T
E
D

2
"

S
C
H

4
0
PVC PIPE

T
R
A
N
S
I
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
3
"

T
O

2
"

S
C
H

4
0
P
V
C

R
E
D
U
C
E
R
3
"

T
O

2
"

S
C
H

4
0
P
V
C

R
E
D
U
C
E
R
3
"

T
O

2
"

S
C
H

4
0
P
V
C

R
E
D
U
C
E
R
3
"

T
O

2
"

S
C
H

4
0
P
V
C

R
E
D
U
C
E
R
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
F
I
R
E

W
A
L
L

P
R
E
S
E
N
T

I
N
S
O
M
E

A
R
E
A
S
SOLID TO SL
O
T
T
E
D

2
"

S
C
H

4
0

P
V
C
PIPE TRANSI
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
S
T
U
D

W
A
L
L
VAPO
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
PIPE PE
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
S
O
L
I
D

T
O

S
L
O
T
T
E
D

2
"

S
C
H

4
0

P
V
C
P
I
P
E

T
R
A
N
S
I
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
2
"

S
C
H

4
0

P
V
C

4
5

D
E
G
R
E
E

E
L
B
O
W
S
L
A
B

S
T
E
P

H
E
I
G
H
T

V
A
R
I
E
S
T
H
I
C
K
E
N
E
D

S
L
A
B

M
A
Y

N
O
T

B
E

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
E
L
E
V
A
T
O
R

S
U
M
P

D
E
T
A
I
L
N
T
S
1
2
V
M
P
-
3
S
U
B
B
A
S
E
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
S
L
A
B

S
T
E
P

H
E
I
G
H
T
V
A
R
I
E
S
V
E
R
T
I
C
A
L

R
I
S
E
R

A
T

S
L
A
B

P
E
N
E
T
R
A
T
I
O
N

W
I
T
H

9
0

D
E
G
R
E
E

E
L
B
O
W
7
N
T
S
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
P
I
P
E

P
E
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
3
"

S
C
H

4
0

P
V
C

9
0

D
E
G
R
E
E

E
L
B
O
W
S
T
U
D

W
A
L
L
3
"

S
C
H

4
0

P
V
C

R
I
S
E
R

D
U
C
T

P
I
P
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
2
)
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
V
M
P
-
3
S
O
L
I
D

T
O

S
L
O
T
T
E
D

2
"

S
C
H

4
0
PVC PIPE

T
R
A
N
S
I
T
I
O
N

(
S
L
I
P

C
O
U
P
L
I
N
G
O
R

T
H
R
E
A
D
E
D

J
O
I
N
T
)
3
"

T
O

2
"

S
C
H

4
0
P
V
C

R
E
D
U
C
E
R
T
H
I
C
K
E
N
E
D

S
L
A
B

M
A
Y

N
O
T

B
E

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
P
R
E
S
S
U
R
E

M
E
A
S
U
R
I
N
G

P
O
I
N
T

W
I
T
H

E
X
T
E
N
D
E
D

I
N
T
A
K
E

P
I
P
E
N
T
S
9
V
M
P
-
3
T
O
P

O
F

T
H
I
C
K
E
N
E
D
S
L
A
B

T
U
R
N
D
O
W
N

V
E
N
T

P
I
P
E
P
R
O
T
E
C
T
I
O
N

S
C
R
E
E
N
B
A
S
E

C
O
A
R
S
E
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
1
)
S
T
U
D

W
A
L
L
(
N
O
T

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
)
F
L
O
O
R

C
L
E
A
N
O
U
T
,

A
D
J
U
S
T
A
B
L
E
,
2
"

D
I
A

Z
U
R
N

I
N
D
U
S
T
R
I
E
S
M
O
D
E
L

#
C
O
2
4
5
0
-
P
V
2

(
O
R

E
Q
U
I
V
A
L
E
N
T
)
V
A
P
O
R

L
I
N
E
R

P
E
N
E
T
R
A
T
I
O
N

S
E
A
L
E
D

T
O
P
I
P
E

P
E
R

M
A
N
U
F
A
C
T
U
R
E
R

I
N
S
T
R
U
C
T
I
O
N
S
S
T
U
D

W
A
L
L
(
N
O
T

P
R
E
S
E
N
T

I
N

A
L
L

L
O
C
A
T
I
O
N
S
)
2
"

S
O
L
I
D

S
C
H

4
0
P
V
C
2
"

S
O
L
I
D

S
C
H

4
0
P
V
C
2
"

S
C
H

4
0
P
V
C

9
0

D
E
G
R
E
E

E
L
B
O
W
2
"

S
O
L
I
D

S
C
H

4
0

P
V
C
3
"

S
C
H

4
0

P
V
C

9
0
D
E
G
R
E
E

E
L
B
O
W
2
"

S
O
L
I
D

S
C
H

4
0

P
V
C
2
"

S
O
L
I
D

S
C
H

4
0

P
V
C
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
5
)
3
"

S
O
L
I
D

S
C
H

4
0

P
V
C
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
5
)
3
"

S
O
L
I
D

S
C
H

4
0

P
V
C
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
5
)
3
"

S
O
L
I
D

S
C
H

4
0

P
V
C
(
S
E
E

S
P
E
C
I
F
I
C
A
T
I
O
N

#
5
)
P
O
S
I
T
I
O
N

P
I
P
E

M
I
N
I
M
U
M

3
4
"
F
R
O
M

C
O
R
N
E
R

O
F

C
O
N
C
R
E
T
E
P
O
S
I
T
I
O
N

P
I
P
E

M
I
N
I
M
U
M

3
4
"
F
R
O
M

C
O
R
N
E
R

O
F

C
O
N
C
R
E
T
E
V
A
P
O
R

M
I
T
I
G
A
T
I
O
N

S
Y
S
T
E
M
D
E
T
A
I
L
S

&

S
P
E
C
I
F
I
C
A
T
I
O
N
S
R
E
V
I
S
I
O
N

1
M
A
Y

1
9
,

2
0
1
7
VAPOR MITIGATION SYSTEM (VMS) SPECIFICATIONS1. VMS VAPOR LINER SHALL BE STEGO WRAP 15-MIL VAPOR BARRIER MANUFACTURED BY STEGOINDUSTRIES LLC (OR, EQUIVALENT ALTERNATIVE VAPOR LINER APPROVED BY THE ENGINEER).ALTERNATIVE VAPOR LINER (IF USED) SHALL BE A POLYOLEFIN FILM DESIGNED TO PREVENTVAPOR MIGRATION THROUGH CONCRETE SLABS-ON-GRADE AND SHALL HAVE THE FOLLOWINGCHARACTERISTICS:·THICKNESS: 15-MIL MINIMUM·PUNCTURE RESISTANCE: 2,200 GRAMS MINIMUM (PER ASTM D 1709)·TENSILE STRENGTH: 45 lbf/in MINIMUM (PER ASTM D 882)·PERMEANCE: 0.01 PERMS MAXIMUM (PER ASTM F 1249)VAPOR LINER SHALL BE INSTALLED AS SPECIFIED HEREIN AND PER MANUFACTURER INSTALLATIONINSTRUCTIONS TO CREATE A CONTINUOUS LINER BELOW FLOOR SLABS LOCATED IN LOWER LEVELRESIDENTIAL LIVING AND RESIDENTIAL AMENITY BUILDING SPACES. A MINIMUM 4-INCH THICKBASE COURSE CONSISTING OF CLEAN #57 OR #67 STONE SHALL BE INSTALLED BENEATH THEVAPOR MITIGATION SYSTEM (VMS) VAPOR LINER.2. VMS PIPING SHALL NOT BE TRAPPED AND SHALL BE SLOPED A MINIMUM OF 18 UNIT VERTICAL IN12 UNITS HORIZONTAL (1% SLOPE) TO GRAVITY DRAIN. PVC PIPE JOINTS SHALL BE CONNECTEDUSING PVC SOCKET COUPLINGS AND PVC GLUE. SUB-SLAB SLOTTED VAPOR COLLECTION PIPESHALL BE THREADED FLUSH JOINT 2" SCH 40 PVC PIPE WITH 0.020" SLOT WIDTH AND 18" SLOTSPACING. FABRIC FILTER SOCK SHALL BE INSTALLED OVER SLOTTED PIPE SECTIONS.ABOVE-SLAB VERTICAL RISER PIPING SHALL BE PERMANENTLY IDENTIFIED BY MEANS OF A TAG ORSTENCIL WITH "VAPOR MITIGATION SYSTEM" AND FAN NUMBER WITHIN EACH FLOOR LEVEL ANDABOVE THE ROOF LINE. 3" PVC VERTICAL RISER PIPING SHALL BE INSTALLED TO CONNECT EACHSLAB PENETRATION LOCATION TO A ROOFTOP EXHAUST DISCHARGE POINT WITH VACUUM FAN(SEE SPECIFICATION #3). ABOVE-SLAB VERTICAL RISER PIPE RUNS BETWEEN THE SLABPENETRATION AND THE ROOFTOP EXHAUST DISCHARGE SHALL BE INSTALLED PER APPLICABLEBUILDING CODE AND AS SPECIFIED IN THE CONSTRUCTION DOCUMENTS AND DRAWINGS.VERTICAL RISER PIPES ABOVE SLAB STEPS SHALL BE PLACED ON THE HIGH SIDE OF THE SLABSTEP.3. VERTICAL RISER PIPING SHALL EXTEND IN A VERTICAL ORIENTATION THROUGH THE BUILDINGROOF. AN IN-LINE RADONAWAY MODEL RP145 VACUUM FAN (OR ALTERNATE ELECTRIC FANAPPROVED BY THE ENGINEER) SHALL BE INSTALLED ON EACH RISER PIPE ABOVE THE BUILDINGROOF LINE AS DEPICTED IN DETAIL #11, AND IN ACCORDANCE WITH MANUFACTURER INSTALLATIONINSTRUCTIONS AND APPLICABLE BUILDING CODE. EXHAUST DUCT PIPE SHALL BE CONNECTED TOTHE OUTLET OF THE FAN USING A FLEXIBLE COUPLING AND EXTEND TO A MINIMUM OF 4 FT ABOVETHE BUILDING ROOF LINE. A 90 DEGREE PVC ELBOW WITH VARMINT SCREEN SHALL BE INSTALLEDON THE END OF EACH EXHAUST DUCT PIPE. THE EXHAUST OUTLET OF EACH DUCT PIPE SHALL BEA MINIMUM OF 10 FT FROM ANY OPERABLE OPENING OR AIR INTAKE INTO THE BUILDING.4. THIS VAPOR MITIGATION PLAN IS INTENDED TO BE USED FOR DIRECTION OF VMS COMPONENTINSTALLATION ONLY AND IS NOT INTENDED TO GUIDE CONSTRUCTION OF STRUCTURALCOMPONENTS NOT RELATED TO THE VMS. CONSTRUCTION CONTRACTOR SHALL VERIFYCONSISTENCY OF VMS DETAILS WITH APPLICABLE STRUCTURAL PLANS AND RESOLVE ANYINCONSISTENCIES PRIOR TO VMS INSTALLATION.5. HORIZONTAL PIPING LOCATED WITHIN SLAB STEBS AND DEPRESSED FOOTINGS SHALL HAVE AMINIMUM OF 2-INCHES OF CONCRETE ABOVE THE PIPING AND 3-INCHES OF CONCRETE BELOW THEPIPING, OR OTHERWISE APPROVED BY DAVIS & CHURCH STRUCTURAL ENGINEERS. PIPINGARRANGEMENT THROUGH DEPRESSED FOOTINGS AND SLAB STEPS MAY BE MODIFIED UPONAPPROVAL BY ENGINEER.NOTE: FOUNDATION PLAN AND DETAILS PROVIDED BY POOLE & POOLE ARCHITECTURE OFMIDLOTHIAN, VA AND DAVIS & CHURCH STRUCTURAL ENGINEERS OF ALPHARETTA, GA FORREFERENCE AND ARE SUBJECT TO COPYRIGHT PROTECTION.
3
7
3
6

W
i
n
t
e
r
f
i
e
l
d

R
o
a
d
,

S
u
i
t
e

1
0
2
M
i
d
l
o
t
h
i
a
n
,

V
i
r
g
i
n
i
a

2
3
1
1
3
T
e
l
e
p
h
o
n
e

8
0
4
.
2
2
5
.
0
2
1
5
w
w
w
.
2
p
a
.
n
e
t
N
C

F
I
R
M

#
5
1
9
7
2
©

2
0
1
6

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
D
r
a
w
i
n
g
s

a
n
d

s
p
e
c
i
f
i
c
a
t
i
o
n
s

a
r
e

a
n
d

s
h
a
l
l

r
e
m
a
i
n

t
h
e
p
r
o
p
e
r
t
y

o
f

P
o
o
l
e

&

P
o
o
l
e

A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C

a
n
d

s
h
a
l
l

n
o
t
b
e

u
s
e
d

o
r

r
e
p
r
o
d
u
c
e
d

i
n

w
h
o
l
e

o
r

p
a
r
t

i
n

a
n
y

f
o
r
m
w
i
t
h
o
u
t

p
r
i
o
r

w
r
i
t
t
e
n

c
o
n
s
e
n
t

o
f

P
o
o
l
e

&

P
o
o
l
e
A
r
c
h
i
t
e
c
t
u
r
e
,

L
L
C
.
D
r
a
w
i
n
g

T
i
t
l
e
:
V
M
P
-
3
2
9
2
3

S
o
u
t
h

T
r
y
o
n

S
t
r
e
e
t
-
S
u
i
t
e

1
0
0
C
h
a
r
l
o
t
t
e
,

N
o
r
t
h

C
a
r
o
l
i
n
a

2
8
2
0
3
7
0
4
-
5
8
6
-
0
0
0
7
(
p
)

7
0
4
-
5
8
6
-
0
3
7
3
(
f
)
L
i
c
e
n
s
e

#

C
-
1
2
6
9

/

#
C
-
2
4
5

G
e
o
l
o
g
y
V
a
p
o
r

M
i
t
i
g
a
t
i
o
n

P
l
a
n

P
r
e
p
a
r
e
d

B
y
:
P
R
O
F
E
S
S
I
O
N
A
L

A
P
P
R
O
V
A
L
NODA VILLAGE
an Apartment Community by
PHILEMON NODA PARTMERS, LLC
at 327 EAST CRAIGHEAD, Charlotte, North Carolina 28206
S:\AAA-Master Projects\Stonehenge Real Estate Group - SHR\SHR-001 Former Abernethy Lumber\Vapor Mitigation Plan\Revision 1\Revised - 03202017\Figures\VMP 3_rev051917.dwg, V1.1, 5/23/2017 3:00:19 PM, TDeSa
NODA Village
Vapor Mitigation System
Monthly Fan O&M Form
Date___________________Inspector_____________________________
Comments
Yes No Note any damage, malfunctions, repairs needed, etc.
F1-1
F1-2
F1-3
F1-4
F1-5
F1-6
F1-7
F1-8
F1-9
F1-10
F1-11
F1-12
F1-13
F1-14
F1-15
F1-16
F1-17
F1-18
F1-19
F1-20
F1-21
F2-1
F2-2
F2-3
F2-4
F2-5
F2-6
F2-7
F2-8
F2-9
F2-10
F2-11
F2-12
2. If fan is not operating or damage is observed, contact Hart & Hickman at 704-586-0007.
Fan Operating?
Building 1
Building 2
1. Vapor mitigation fans shall be inspected on a monthly basis and these forms shall be submitted to the DEQ Brownfields Program on a
yearly basis.
Fan Number
Stego Industries, LLC ‹San Clemente, CA
Tel: [phone] ‹ Toll Free: 877-464-7834 ‹ Fax: [phone]
www.stegoindustries.com
STEGO ® WRAP VAPOR BARRIER
ASTM E 1745 Class A-B-C Compliant
is made with our proven trade
secret blend of prime virgin resins
and additives. Stego Wrap Vapor
Barrier is an ASTM E 1745 Class A
Vapor Barrier (Below 0.01 perms).
We focus on producing a product
that will maintain its extremely low
permeance for the life of a building.
The protection of Stego Wrap Vapor
Barrier provides the flexibility to
change flooring types and overall
building use without worrying about
below-slab moisture vapor.
STEGO® WRAP
VAPOR BARRIER
FEATURES & BENEFITS
Unsurpassed Permeance
Characteristics
Life of the Building
Protection
Exceptional Tear and Puncture
Resistance
Easy, Reliable Installation
Competitively Priced
Available Nationwide
Local Support
SUPERIOR DEFENSE Against Floor Failures:
Experts say “the need for a vapor barrier (as opposed to a vapor retarder) is becoming
increasingly clear.” Concrete Construction Magazine, August 2003, p.18.
Infiltration of moisture through concrete slabs is a major building defect liability.
Stego Wrap Vapor Barrier has an extremely low permeance preventing water vapor,
soil gases (i.e. Radon), alkaline salts and soil sulfates from compromising the integrity
of the building envelope and leading to serious problems with the concrete slab, floor
coverings and indoor air quality. Stego Wrap Vapor Barrier is the best protection
against these costly failures.
MOLD PREVENTION:
Mold needs three things to survive: moisture, sustained temperature (between 50° and
122° F), and a food source (dust, drywall, etc.). In any given building environment,
contractors can only control one of these variables: moisture. Mold spores are present
in 100% of building interiors. If moisture is allowed into your building environment,
mold can and will grow. Toxic molds like Stachybotyrus can be fatal for nearly 5% of
people (Institute of Medicine 1993), and cause a variety of serious health problems
in others. Several recent well-publicized cases involving toxic mold have resulted
in multimillion-dollar insurance settlements. Many of the nation's leading Insurance
companies have severely limited or removed coverage for mold claims fearing that
these claims will bankrupt their companies. Now more than ever, it is critically
important that extra attention be paid to preventing the intrusion of moisture vapor
from your below-slab environment. Stego Wrap Vapor Barrier offers the level of
protection that many architects are now seeking and is considered to be inexpensive
insurance against these costly failures.
LONGEVITY AND STRENGTH:
Stego Wrap Vapor Barrier is NOT made with recycled materials and will not degrade.
Prime, virgin resins are the key. Molecules within Stego Wrap "interlock" to provide
strength, durability and unprecedented resistance to moisture vapor and radon gas.
Stego Wrap’s puncture resistance is excellent. Stego Wrap will not tear, crack, flake,
snag or puncture, even when 18,000 lb. laser-screed machines are driving directly
across the barrier (see the reverse side for Stego Wrap Vapor Barrier’s specifications).
THE STEGO® ADVANTAGES
INSTALLATION INSTRUCTIONS: (Based on ASTM E 1643)
Unroll Stego Wrap over the area where the slab is to be placed. Stego
Wrap should completely cover the concrete placement area. Overlap
seams 6 inches and tape using Stego Tape. All penetrations and
blockouts should be sealed using a combination of Stego Wrap,
Stego Tape and/or Stego Mastic. If the Stego Wrap is damaged,
cut a piece from the Stego Wrap roll, place over the damaged area,
and tape around all edges. Concrete may be placed directly on Stego
Wrap. For additional information, please refer to Stego's complete
installation instructions.
STEGO ® TAPE:
STEGO WRAP RED POLYETHYLENE TAPE (3.75” x 180’/roll) is specially designed to seal seams and penetrations
on Stego Wrap installations. The acrylic, pressure-sensitive adhesive provides permanent bonding and quick-stick
properties. The area to be bonded should be free of dust, dirt and moisture.
WARRANTY:
STEGO INDUSTRIES, LLC believes, to the best of its knowledge, that specifications and recommendations herein
are accurate and reliable. However, since site conditions and installations are not within our control, STEGO
INDUSTRIES, LLC does not guarantee results from use of the information provided and disclaims all liability from
any loss or damage. NO WARRANTY EXPRESS OR IMPLIED IS GIVEN AS TO THE MERCHANTABILITY, FITNESS FOR PARTICULAR
PURPOSE, OR OTHERWISE WITH RESPECT TO THE PRODUCTS REFERRED TO.
Note: Test results above are for Stego Wrap products made as of March 15, 2013. If you have product made prior to March 15, 2013, please refer to
Stego literature dated 10/12 for representative test results or call your local Stego Representative with questions.
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
Stego Industries, LLC ‹San Clemente, CA
Tel: [phone] ‹ Toll Free: 877-464-7834 ‹ Fax: [phone] ‹ www.stegoindustries.com 04/2013
Note: perm unit = grains/(ft2 *hr* in.Hg) * WVTR = water vapor transmission rate **GTR = Gas Transmission Rate
STEGO ® WRAP VAPOR BARRIER SPECIFICATIONS
PROPERTIES TEST METHOD ASTM E 1745 TEST RESULT EXPLANATION
Class A Requirements Permeance ASTM F 1249 0.1 perms 0.0086 perms Very impermeable * 0.0036 WVTR to water vapor Puncture Resistance ASTM D 1709 2200 grams Method B 2266 grams Resistant to puncturing from construction abuse Tensile Strength ASTM D 882 45.0 lbf./in. 70.6 Ibf./in. Will not tear easily
ASTM E 154 0.1 perms 0.0098 perms Permeance after wetting, drying, Permeance section 8 and soaking ASTM E 154 0.1 perms 0.0091 perms Permeance after heat After section 11 conditioning
ASTM E 154 0.1 perms 0.0097 perms Permeance after low Conditioning section 12 temperature conditioning
(ASTM E 1745 Sections ASTM E 154 0.1 perms 0.0095 perms Permeance after soil 7.1.2 - 7.1.5) section 13 organism exposure
Methane Transmission ASTM D 1434 **GTR = 192.8 Greatly impedes the Rate mL(STP)/m2*day transmission of methane gas
Radon Diffusion 5.5 x 10-14m2/second Greatly impedes the Coefficient transmission of radon gas
Thickness 15 mils Stronger, tougher and less permeable than much thicker membranes Roll Dimensions 14 ft. X 140 ft. 1,960 ft2/roll - allows for a minimum of seams
Roll Weight 140 lbs. Easy to unroll and install
STEGO WRAP VAPOR BARRIER
VAPOR BARRIER
STEGOWRAP
CONCRETE SLAB
Rebar
SUBGR
A
D
E
1. Product Name
Stego Wrap Vapor Barrier
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Wrap Vapor Barrier is used
as a below-slab vapor barrier.
COMPOSITION: Stego Wrap Vapor
Barrier is a multi-layer plastic extrusion
manufactured with only high grade
prime, virgin, polyolefin resins.
ENVIRONMENTAL FACTORS:
Stego Wrap Vapor Barrier can be used
in systems for the control of soil gases
(radon, methane), soil poisons (oil
by-products) and sulfates.
Vapor Retarders
07 26 00, 03 30 00
5. Installation
UNDER SLAB: Unroll Stego Wrap Vapor
Barrier over an aggregate, sand or
tamped earth base. Overlap all seams
a minimum of six inches and tape using
Stego Tape or Crete Claw® Tape. All
penetrations must be sealed using a
combination of Stego Wrap and Stego
accessories.
For additional information, please
refer to Stego's complete installation
instructions.
6. Availability & Cost
Stego Wrap Vapor Barrier is available
nationally via building supply dis-
tributors. For current cost information,
contact your local Stego Wrap dis-
tributor or Stego Industries’ sales
department.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that specifica-
tions and recommendations herein are
accurate and reliable. However, since
site conditions are not within its control,
Stego Industries does not guarantee
results from the use of the information
provided and disclaims all liability
from any loss or damage. No warranty,
express or implied, is given as to the
merchantability, fitness for a particular
purpose, or otherwise with respect to
the products referred to.
8. Maintenance
None required.
9. Technical Services
Technical advice, custom CAD drawings,
and additional information can be
obtained by contacting Stego Industries’
technical assistance department or via
the website.
10. Filing Systems
™HiZ\d>cYjhig^Zh¼lZWh^iZ
™7j^aYh^iZ
™)HeZXh
STEGO INDUSTRIES, LLC
Stego® Wrap Vapor Barrier
04/2013Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
TABLE 1: PHYSICAL PROPERTIES OF STEGO WRAP VAPOR BARRIER
PROPERTY TEST RESULTS
Under Slab Vapor Retarders ASTM E 1745 Class A, B & C – Standard Specification for Water Vapor Retarders Used
in Contact with Soil or Granular Fill under Concrete Slabs Exceeds Class A, B & C
Water Vapor Permeance ASTM F 1249 – Test Method for Water Vapor Transmission Rate Through Plastic Film and 0.0086 perms
Sheeting Using a Modulated Infrared Sensor *0.0036 WVTR
Puncture Resistance ASTM D 1709 – Test Methods for Impact Resistance of Plastic Film by Free-Falling
Dart Method 2266 grams
Tensile Strength ASTM D 882 – Test Method for Tensile Properties of Thin Plastic Sheeting 70.6 lbf/in.
Permeance After Conditioning ASTM E 154 Section 8, F 1249 – Permeance after wetting, drying, and soaking 0.0098 perms
(ASTM E 1745 ASTM E 154 Section 11, F 1249 – Permeance after heat conditioning 0.0091 perms
Sections 7.1.2 - 7.1.5) ASTM E 154 Section 12, F 1249 – Permeance after low temperature conditioning 0.0097 perms
ASTM E 154 Section 13, F 1249 – Permeance after soil organism exposure 0.0095 perms
Methane Transmission Rate ASTM D 1434 – Standard Test Method for Determining Gas Permeability Characteristics **192.8 GTR
of Plastic Film and Sheeting mL(STP)/m2*day
Radon Diffusion Coefficient 5.5 x 10-14m2/second
Thickness ACI 302.1R-04 – Minimum Thickness (10 mils) 15 mils
Roll Dimensions 14 ft. wide x 140 ft. long
or 1,960 ft2
Roll Weight 140 lbs.
Note: perm unit = grains/(ft2 *hr* in.Hg) * WVTR = Water Vapor Transmission Rate ** GTR = Gas Transmission Rate
Note: Test results above are for Stego Wrap products made as of March 15, 2013. If you have product made prior to March 15, 2013 please refer to Stego literature dated
10/12 for representative test results or call your local Stego Representative with questions.
4. Technical Data
1. Product Name
Stego Mastic
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Mastic is designed to be
used as a waterproofing and vapor
retardant membrane for use in
conjunction with Stego Wrap 10-mil and
15-mil Vapor Retarder/Barrier. Stego
Mastic can be used as an alternate to
boots for pipe penetrations in Stego
Wrap Vapor Barrier.
COMPOSITION: Stego Mastic is a
medium-viscosity, water-based,
polymer-modified anionic bitumin-ous/
asphalt emulsion, which exhibits
bonding, elongation and water-proofing
characteristics.
SIZE: Stego Mastic comes in five-gallon
buckets.
4. Technical Data
APPLICABLE STANDARDS:
American Society for Testing and
Materials (ASTM)
™6HIB 9 )&' HiVcYVgY IZhi BZi]dY
for Vulcanized Rubber and Therm-
oplastic Elastomers - Tension
™6HIB:&*)HiVcYVgYIZhiBZi]dYh
for Water Vapor Retarders Used in
Contact with Earth under Concrete
Slabs, on Walls, or as Ground Cover
™ 6HIB < '( EgVXi^XZ [dg DeZgVi^c\
Light-Exposure Apparatus (Carbon-
Arc Type) With and Without Water for
Exposure of Nonmetallic Materials
(Withdrawn 2000)
™ 6HIB : .+ HiVcYVgY IZhi BZi]dYh
for Water Vapor Transmission of
Materials
™ 6HIB9,*&HiVcYVgYIZhiBZi]dYh
for Coated Fabrics
™ 6HIB9&)()HiVcYVgYIZhiBZi]dY
for Determining Gas Permeability
Characteristics of Plastic Film and
Sheeting
™ 6HIB 8 -(+ HiVcYVgY HeZX^[^XVi^dc
for High Solids Content, Cold Liquid-
Applied Elastomeric Water-proofing
Vapor Retarders
07 26 00, 03 30 00
Membrane for Use with Separate
Wearing Course.
™ 6HIB:&+)(HiVcYVgYEgVXi^XZ[dg
Installation of Water Vapor Retarders
Used in Contact with Earth or
Granular Fill under Concrete Slabs.
5. Installation
PREPARATION:
™  6 iZhi Veea^XVi^dc h^bjaVi^c\ i]Z
project environment should always
be done prior to final usage of Stego
Mastic.
™ 6aaHjg[VXZhh]djaYWZYgnVcY[gZZ
of loose materials, oils and other
contaminants. The surfaces should
be cleaned in the same fashion as
the test surface in order to ensure
proper results.
™ HidgZVWdkZ)%•;
PENETRATIONS:
For small pipe and rebar penetrations in
Stego Wrap Vapor Barrier cut Stego
Wrap just big enough for the pene-
tration. Liberally apply Stego Mastic
around the penetration to keep the
integrity of the membrane intact. Stego
Mastic can be applied by brush, roller, or
sprayer.
NOTES: 1) For larger penetrations or
wide cut-outs of Stego Wrap, use Stego
Wrap and Stego Tape to repair and seal.
2) Solvent-based products should not be
applied over this product. 3)Clean all
tools with kerosene and/or oil-based
cleaners.
STEGO INDUSTRIES, LLC
Stego® Mastic
04/2013
For additional information, please refer
to Stego's complete installation
instructions.
6. Availability & Cost
Stego Mastic is available nationally via
building supply distributors. For current
cost information, contact your local
Stego distributor or Stego Industries’
sales department.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that specifications
and recommendations herein are
accurate and reliable. However, since
site conditions are not within its control,
Stego Industries does not guarantee
results from the use of the information
provided and disclaims all liability from
any loss or damage. No warranty,
express or implied, is given as to the
merchan-tability, fitness for a particular
purpose, or otherwise with respect to
the products referred to.
8. Maintenance
None required.
9. Technical Services
Technical advice, custom CAD drawings,
and additional information can be
obtained by contacting Stego Industries’
technical assistance department or by
visiting the website.
10. Filing Systems
™HiZ\d>cYjhig^Zh¼lZWh^iZ
™7j^aYh^iZ
TABLE 1: PHYSICAL PROPERTIES OF STEGO MASTIC
Property and Test Stego Mastic
Tensile/Elongation, ASTM D 412 32 psi / 3860%
Resistance to Decay, ASTM E 154 9% perm loss
Accelerated Aging, ASTM G 23 No Effect
Permeance, ASTM E 96 0.17 Perms
Hydrostatic Water Pressure, ASTM D 751 28 psi
Methane Transmission Rate, ASTM D 1434 0
Adhesion to Concrete & Masonry, ASTM C 836 7 lbf./in.
Hardness, ASTM C 836 85
Crack Bridging, ASTM C 836 No Cracking
Low Temp Flexibility, ASTM C 836 No Cracking at -20°C
Resistance to Acids:
Acetic 30%
Sulfuric and Hydrochloric 15%
Temperature Effect:
Stable 248°F
Flexible 13°F
Note: perm unit = grains/(ft2 *hr* in.Hg)
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
1. Product Name
Stego Tape
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Tape is a low permeance
tape designed for protective sealing,
hanging, seaming, splicing, and
patching applications where a highly
conformable material is required.
It has been engineered to bond
specifically to Stego Wrap, making it
ideal for sealing Stego Wrap seams
and penetrations.
COMPOSITION: Stego Tape is
composed of polyethylene film
and an acrylic, pressure-sensitive
adhesive.
SIZE: Stego Tape is 3.75” wide and
180’ long. Stego Tape ships 12 rolls
in a case.
4. Technical Data
APPLICABLE STANDARDS:
Pressure Sensitive Tape Council
(PSTC)
™PSTC 101 – International Standard
for Peel Adhesion of Pressure
Sensitive Tape
American Society for Testing &
Materials (ASTM)
™ASTM E 1643 - Standard Practice for
Selection, Design, Installation, and
Inspection of Water Vapor Retarders
Used in Contact with Earth or
Granular Fill under Concrete Slabs
5. Installation
SEAMS:
Overlap Stego Wrap six inches and
seal with Stego Tape. Make sure the
area of adhesion is free from dust,
dirt, moisture and frost to allow
maximum adhesion of the pressure
sensitive tape.
Vapor Retarders
07 26 00, 03 30 00
PIPE PENETRATION SEALING
1) Install Stego Wrap around pipe by
slitting/cutting material
2) If void space around pipe is
minimal, seal around base of
pipe with Stego Tape (Stego
Mastic can be used for additional
coverage)
DETAIL PATCH FOR PIPE PENETRATION
SEALING
1) Cut a piece of Stego Wrap that
creates a six inch overlap around
all edges of the void space
2) Cut an “X” in the center of the
detail patch
3) Slide detail patch over pipe,
secure tightly
4) Tape down all sides of detail
patch with Stego Tape
5) Seal around base of pipe with
Stego Tape (Stego Mastic can be
used for additional coverage)
Stego Tape should be installed above
40°F. In temperatures below 40°F,
take extra care to remove moisture
or frost from the area of adhesion.
For additional information, please
refer to Stego's complete installation
instructions.
6. Availability & Cost
Stego Tape is available nationally
via building supply distributors. For
current cost information, contact
your local Stego distributor or Stego
Industries’ sales department.
7. Warranty
Stego Industries, LLC believes
to the best of its knowledge, that
specifications and recommend-
ations herein are accurate and
reliable. However, since site
conditions are not within its control,
Stego Industries does not guarantee
results from the use of the
information provided and disclaims
all liability from any loss or damage.
No warranty, express or implied,
is given as to the merchantability,
fitness for a particular purpose,
or otherwise with respect to the
products referred to.
8. Maintenance
None required.
9. Technical Services
Technical advice, custom CAD
drawings, and additional infor-
mation can be obtained by
contacting Stego Industries’
technical assistance department or
by visiting the website.
10. Filing Systems
™HiZ\d>cYjhig^Zh¼lZWh^iZ
™7j^aYh^iZ
TABLE 1: PHYSICAL PROPERTIES OF STEGO TAPE
PROPERTY RESULTS
Total Thickness 6 mils
Permeance 0.03 perms
Tensile Strength 17 lbs./in. width
Elongation (at break) MD 1060%
Adhesion (20 min dwell ss, PSTC 101) 95-oz./in. width
Ultraviolet Resistance Excellent
STEGO INDUSTRIES, LLC
Stego® Tape
04/2013Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
STEGO CRETE CLAW® TAPE
Stego Crete Claw® Tape provides an innovative and economical way to secure
plastic film to concrete while the concrete is still wet.
Crete Claw is a multi-layered tape/detail strip that will mechanically lock Stego
Wrap Vapor Barrier to concrete. The patent-pending design allows wet concrete to
cast into the textured surface of Crete Claw. Just stick Crete Claw to Stego Wrap
prior to concrete placement, then place the concrete directly over the system.
Stego Crete Claw can be used in place of Stego Tape to seal joints in Stego Wrap
Vapor Barrier providing a dual purpose and helping to offset costs. ANGLED TOP VIEW
The patent-pending design allows wet concrete to cast into the textured surface of Crete Claw
SETTLING SOIL USE CRETE CLAW TOSEAL JOINTS INSTEGO WRAP
VAPOR BARRIERSTEGO CRETE CLAW® TAPE
BELOW SLAB
STEGO INDUSTRIES, LLC | San Clemente, CA | 949-257-4100 | Toll Free 877-464-7834 | Fax [phone] | www.stegoindustries.com
Contact us to learn more about this innovative product.
TABLE 1: CRETE CLAW TAPE TEST RESULTS
PROPERTY TEST RESULTS
Total Thickness 26 mils
Permeance ASTM F 1249 0.03 perms
180° Adhesion Peel Strength ASTM D 903 17.6 lbf/in.
Sheer Adhesion Strength 1 in.2 shear test using an Instron 3345 Machine >49 lbf/in.2*
Roll Sizes 6” x 180’ and 3” x 180’ **
* Specimens failed by stretching vapor barrier to failure before pulling Crete Claw from concrete.
** 3” wide is for perimeter seal application only.
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.04/2013
MOST COMMON APPLICATIONS FOR CRETE CLAW® 6” Wide 3” Wide
ASTM E 1643 - Forming seal to the slab at perimeter
Securing Stego Wrap to bottom of slab for
expansive/settling soils and carton/void
form applications
Perimeter
Seams
99
9
9
Other more expensive products rely
on chemical reaction or geotextile
to bond with concrete making it all
but impossible to properly install the
vapor barrier. Often in pursuit of the
all-in-one product, the performance
characteristics of the vapor barrier
are compromised. Because Crete
Claw Tape is applied as a separate
accessory to the vapor barrier, it
does not interfere with the ability to
detail around penetrations or repair
damaged areas.
Quick and easy
to install
Saves time
and money
Innovative Solution to
help meet ASTM E 1643
VAPOR BARRIER
SEAL ALL SEAMS
IN STEGO WRAP
USING 6” WIDE CRETE CLAW TAPE
STEGO CRETE CLAW® TAPE
INSTALL 6” WIDE CRETE CLAW TAPE ON EDGE
OF STEGO WRAP WHERE STEGO WRAP
MEETS INTERIOR FOOTING
OR GRADE BEAM
INSTALL CRETE CLAW TAPE
ON THE ENTIRE PERIMETER
EDGE OF STEGO WRAP.
TOP-DOWN VIEWS OF A BUILDING FOOTPRINTTOP-DOWN VIEWS OF A BUILDING FOOTPRINT
STEGO CRETE CLAW® TAPE
INSTALLATION INSTRUCTIONS
SEAL ALL PENETRATIONS WITH STEGO TAPE AND/OR STEGO MASTIC.
CRETE CLAW TAPE IS NOT MEANT FOR REPAIRING PENETRATIONS.
STEGO® MASTICSTEGO® TAPE
OR
VAPOR BARRIER
STEGO CRETE CLAW® TAPE
1. Clean surface of Stego Wrap to ensure that it is free of moisture
and debris prior to the installation of 6” wide Crete Claw Tape.
2. Overlap seams a minimum of 6 inches. Seal all seams in Stego
Wrap using Crete Claw Tape.
3. Install 6“ wide Crete Claw Tape on the entire perimeter of the
Stego Wrap Installation. Crete Claw Tape should be completely on
Stego Wrap.
4. Install additional Crete Claw Tape if required. Lab and simulated
field tests have shown that if 6” wide Crete Claw is installed on all
seams and around the perimeter, then it is more than strong enough
to support Stego Wrap. If determined by the architect or engineer,
additional Crete Claw may be specified.
5. Prior to the placement of concrete, ensure that Crete Claw is free
of dirt or debris to ensure maximum bond to the concrete.
These are general instructions. Installation requirements may change
on a project-by-project basis
IMPORTANT - For the application of securing Stego Wrap to the
bottom of the slab, always use 6” wide Crete Claw Tape.
1. Clean surface of Stego Wrap to ensure that it is free of moisture and
debris prior to the installation of Crete Claw Tape.
2. Install 3” or 6” Crete Claw Tape on the entire perimeter of the Stego
Wrap Installation. Crete Claw Tape should be completely on
Stego Wrap.
SEAL ALL SEAMS
IN STEGO WRAP
USING STEGO TAPE
INSTALL CRETE CLAW TAPE ON EDGE OF
STEGO WRAP WHERE STEGO WRAP
MEETS INTERIOR FOOTING
OR GRADE BEAM
INSTALL CRETE CLAW TAPE
ON THE ENTIRE PERIMETER
EDGE OF STEGO WRAP.PERIMETER SEAL TO SLAB
SECURING STEGO WRAP TO THE BOTTOM
OF THE SLAB
CRETE CLAW CAN BE USED TO SEAL SEAM AROUND
DETAIL PATCH FOR ADDED PROTECTION.
.)."'*,")&%%™-,,")+)",-()™lll#hiZ\d^cYjhig^Zh#Xdb
NOTE: Stego Industries, LLC’s (“Stego”) installation instructions are based on ASTM E 1643 - Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor
Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs. These instructions are meant to be used as a guide, and do not take into account specific job site
situations. Consult local building codes and regulations along with the building owner or owner’s representative before proceeding. If you have any questions regarding the above
mentioned installation instructions, Stego products, please call us at 877-464-7834 for technical assistance. While Stego employees and representatives may provide technical
assistance regarding the utility of a specific installation practice or Stego product, they are not authorized to make final design decisions.
TABLE 1: PHYSICAL PROPERTIES OF STEGO CRETE CLAW
PROPERTY RESULTS
Dimensions 6" x 180'
Total Thickness 26 mils
Permeance: ASTM F 1249 0.03 perms
180° Adhesion Peel Strength: ASTM D 903 17.6 lbf/in.
Sheer Adhesion Strength:
1 in2 shear test using an Instron 3345 Machine >49 lbf/in2*
* Specimens failed by stretching vapor barrier to failure before pulling Crete Claw from concrete.
1. Product Name
Stego® Crete Claw® Tape
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Crete Claw Tape is
a multi-layered tape that is used
to seal Stego Wrap to concrete
while the concrete is still wet.
Crete Claw allows wet concrete to
cast into the textured top surface
to form a mechanical bond/seal.
COMPOSITION: Stego Crete Claw
is composed of polyethylene film,
aperture film, and an acrylic,
pressure sensitive adhesive.
SIZE: Stego Crete Claw is 6” wide by
180’ long. Stego Crete Claw ships 8
rolls in a case.
4. Technical Data
Vapor Retarders
07 26 00
5. Installation
SECURING STEGO WRAP TO SLAB:
Clean the surface of Stego Wrap to
ensure that it is free of moisture,
frost, dirt, and debris prior to the
installation of Stego Crete Claw.
When ready to apply Crete Claw,
peel back the release liner and
apply to Stego Wrap. Stego Crete
Claw should be completely on Stego
Wrap.
Install Crete Claw Tape on all seams
and around the entire perimeter of
the Stego Wrap installation.
To detail, cut Stego Crete Claw with
a box knife or scissors. Crete Claw
should be installed above 40°F for
maximum adhesion. For additional
information, please refer to Stego’s
complete installation instructions.
TIP: Wrap the release liner back
over the entire roll while unrolling
Crete Claw. This technique will
allow the release liner to pull off
easily and keep it out of the way.
STEGO INDUSTRIES, LLC
Stego® Crete Claw® Tape
04/2013Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
6. Availability & Cost
Stego Crete Claw is available
nationally through our network of
building supply distributors. For
current cost information, contact
your local Stego Wrap distributor
or Stego Industries’ Sales
Representative.
7. Warranty
Stego Industries, LLC believes
to the best of its knowledge, that
specifications and recommend-
ations herein are accurate and
reliable. However, since site
conditions are not within its control,
Stego Industries does not guarantee
results from the use of the
information provided and disclaims
all liability from any loss or damage.
No warranty, express or implied,
is given as to the merchantability,
fitness for a particular purpose,
or otherwise with respect to the
products referred to.
8. Maintenance
Store Stego Crete Claw in a dry and
temperate area.
9. Technical Services
Technical advice, custom CAD
drawings, and additional information
can be obtained by contacting Stego
Industries’ technical department or
via our website.
10. Filing Systems
www.stegoindustries.com
Buildsite
1. Product Name
Stego® Crete Claw® (3" Wide)
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Crete Claw is a multi-
layered tape that is used to seal
Stego Wrap to the perimeter of the
slab while the concrete is placed.
Crete Claw allows wet concrete to
cast into the textured top surface
to form a mechanical bond/seal.
COMPOSITION: Stego Crete Claw
is composed of polyethylene film,
aperture film, and an acrylic,
pressure sensitive adhesive.
SIZE: Stego Crete Claw (3” Wide) is
3” wide and 180’ long. Stego Crete
Claw (3” Wide) ships 16 rolls in a
case.
4. Technical Data
Vapor Retarders
07 26 00
5. Installation
UNDER SLAB: Clean surface of
Stego Wrap to ensure that it is free
of moisture, frost, dirt, and debris
prior to the installation of Stego
Crete Claw. When ready to apply
Crete Claw, peel back the release
liner and apply to Stego Wrap. Stego
Crete Claw should be completely on
Stego Wrap.
To detail, cut Stego Crete Claw with
a box knife or scissors. Crete Claw
should be installed above 40°F for
maximum adhesion. For additional
information please refer to Stego's
complete installation instructions.
TIP: Wrap the release liner back
over the entire roll while unrolling
Crete Claw. This technique will
allow the release liner to pull off
easily and keep it out of the way.
6. Availability & Cost
Stego Crete Claw (3” Wide) is
available nationally through
our network of building supply
distributors. For current cost
information, contact your local Stego
Wrap distributor or Stego Industries’
Sales Representative.
7. Warranty
Stego Industries, LLC believes
to the best of its knowledge, that
specifications and recommend-
ations herein are accurate and
reliable. However, since site
conditions are not within its control,
Stego Industries does not guarantee
results from the use of the
information provided and disclaims
all liability from any loss or damage.
No warranty, express or implied,
is given as to the merchantability,
fitness for a particular purpose,
or otherwise with respect to the
products referred to.
8. Maintenance
Store Stego Crete Claw in a dry and
temperate area.
9. Technical Services
Technical advice, custom CAD
drawings, and additional information
can be obtained by contacting Stego
Industries’ technical department or
via our website.
10. Filing Systems
www.stegoindustries.com
Buildsite
STEGO INDUSTRIES, LLC
Stego® Crete Claw® (3" Wide)
04/2013Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
TABLE 1: PHYSICAL PROPERTIES OF STEGO CRETE CLAW (3" Wide)
PROPERTY RESULTS
Dimensions 3" x 180'
Total Thickness 26 mils
Permeance: ASTM F 1249 0.03 perms
180° Adhesion Peel Strength: ASTM D 903 17.6 lbf/in.
Sheer Adhesion Strength:
1 in2 shear test using an Instron 3345 Machine >49 lbf/in2*
* Specimens failed by stretching vapor barrier to failure before pulling Crete Claw from concrete.
1. Product Name
StegoTack® Tape
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: StegoTack Tape is a double-
sided adhesive strip used to bond
and seal Stego Wrap to concrete,
masonry, wood, metal, and other
surfaces. StegoTack is a flexible
and moldable material to allow
for a variety of applications and
installations.
COMPOSITION: StegoTack Tape
is made from a blend of synthetic
rubber and resins. SIZE: StegoTack
Tape is 2 inches wide and 50 feet
long. StegoTack Tape ships 12 rolls
in a case.
5. Installation
TO WALLS: Make sure the area of
Vapor Retarders
07 26 00, 03 30 00
adhesion is free of dust, dirt, debris,
moisture, and frost to allow maximum
adhesion. Remove release liner on one
side and stick to desired surface. When
ready to apply Stego Wrap, remove the
exposed release liner and press Stego
Wrap firmly against StegoTack Tape to
secure.
TO FOOTINGS: Make sure the area of
adhesion is free of dust, dirt, debris,
moisture, and frost to allow maximum
adhesion. Remove release liner on one
side and stick to desired surface. When
ready to apply Stego Wrap, remove the
exposed release liner and press Stego
Wrap firmly against StegoTack Tape to
secure.
Cut StegoTack Tape using a utility
knife or scissors. Cut StegoTack Tape
before removing the release liner for
easier cutting. Install StegoTack Tape
between 40°F and 110°F. For additional
information please refer to Stego's
complete installation instructions.
6. Availability & Cost
StegoTack Tape is available nationally
through our network of building
supply distributors. For current cost
information, contact your local Stego
STEGO INDUSTRIES, LLC
StegoTack® Tape
04/2013
Wrap distributor or Stego Industries’
Sales Representative.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that specifications
and recommendations herein are
accurate and reliable. However, since
site conditions are not within its control,
Stego Industries does not guarantee
results from the use of the information
provided and disclaims all liability
from any loss or damage. No warranty,
express or implied, is given as to the
merchantability, fitness for a particular
purpose, or otherwise with respect to
the products referred to.
8. Maintenance
For longer adhesive life, store in dry,
temperate area.
9. Technical Services
Technical advice, custom CAD drawings,
and additional information can be
obtained by contacting Stego Industries’
technical assistance department or via
the website. www.stegoindustries.com
10. Filing Systems
www.stegoindustries.com
Buildsite
TABLE 1: PHYSICAL PROPERTIES OF STEGOTACK TAPE
PROPERTY RESULTS
Dimensions 50 feet long,
2 inches wide
Total Thickness 30 Mils
Permeance 0.03 perms (30 mils)
Color Grey
Material Synthetic rubber blend
Adhesion to Steel 10.3 lbs./in. width ASTM C 1000
Installation Temperature 40°F/110°F (4°C/43°C)
In Service Temperature Range -20°F/+140°F (-29°C/60°C)
VOC Content No VOC’s, 100% solids
4. Technical Data
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
1. Product Name
Stego Term Bar
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Term Bar is a semi-
flexible plastic termination bar used for
mechanically securing Stego Wrap or
other materials to concrete, masonry,
or wood.
COMPOSITION: Stego Term Bar is made
from post-industrial recycled PVC.
5. Installation
UNDER SLAB: Nail through Stego Term
Bar and Stego Wrap to secure material
as needed. If the beveled edge is facing
the wall, a pocket/lip is created for
mastic/sealant to be used if required.
Vapor Retarders
07 26 00, 03 30 00
Pre-drilled nail holes are provided every
6 inches for ease of installation.
To cut Stego Term Bar, score with a
utility knife or wire snips. Stego Term
Bar can be bent back and forth and then
broken at desired locations as well.
Stego Term Bar is flexible enough to
bend around corners and contours in the
wall for easy installation.
For additional information, please
refer to Stego's complete installation
instructions.
6. Availability & Cost
Stego Term Bar is available nationally
through our network of building
supply distributors. For current cost
information, contact your local Stego
Wrap distributor or Stego Industries’
Sales Representative.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that specifications
and recommendations herein are
STEGO INDUSTRIES, LLC
Stego® Term Bar
04/2013
TABLE 1: PHYSICAL PROPERTIES OF STEGO TERM BAR
PROPERTY RESULTS
Dimensions 4 feet long,
1 1/8 inches wide
Color Red
Material Recycled PVC
Weight 4.7 oz. (132 grams)
4. Technical Data
accurate and reliable. However, since
site conditions are not within its control,
Stego Industries does not guarantee
results from the use of the information
provided and disclaims all liability
from any loss or damage. No warranty,
express or implied, is given as to the
merchantability, fitness for a particular
purpose, or otherwise with respect to
the products referred to.
8. Maintenance
Store above 60°F. Term Bar will become
less flexible at lower temperatures.
9. Technical Services
Technical advice, custom CAD drawings,
and additional information can be
obtained by contacting Stego Industries’
technical assistance department or via
the website. www.stegoindustries.com
10. Filing Systems
www.stegoindustries.com
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
1. Product Name
Stego Pre-Cut Pipe Boots
2. Manufacturer
Stego Industries, LLC
216 Avenida Fabricante, Suite 101
San Clemente, CA 92672
Sales, Technical Assistance
Ph: [phone]
Fx: [phone]
www.stegoindustries.com
3. Product Description
USES: Stego Pre-Cut Pipe Boots are used
to seal around permanent penetrations
in Stego Wrap.
COMPOSITION: Stego Pre-Cut Pipe
Boots are made from Stego Wrap
Vapor Barrier (15-mil), and therefore
are manufactured from only high grade
prime, virgin, polyolefin resins.
SIZE: Stego Pre-Cut Pipe Boots are 18”
by 18” and 15 mils thick. Stego Pre-Cut
Pipe Boots ship 10 packs of 25 in a case
(250 boots per case).
Vapor Retarders
07 26 00, 03 30 00
5. Installation
UNDER SLAB: Cut an “X” the size of the
pipe diameter in the center of the Pre-
Cut Pipe Boot and slide tightly over pipe.
Tape all sides of the pipe boot with Stego
Tape. Seal around the base of the pipe
using Stego tape and/or Stego Mastic.
For additional information, please
refer to Stego's complete installation
instructions.
6. Availability & Cost
Stego Pre-Cut Pipe Boots are available
nationally through our network of
building supply distributors. For
current cost information, contact your
local Stego Wrap distributor or Stego
Industries’ Sales Representative.
7. Warranty
Stego Industries, LLC believes to the
best of its knowledge, that specifica-
tions and recommendations herein are
accurate and reliable. However, since
site conditions are not within its control,
Stego Industries does not guarantee
results from the use of the information
provided and disclaims all liability
from any loss or damage. No warranty,
express or implied, is given as to the
merchantability, fitness for a particular
purpose, or otherwise with respect to
the products referred to.
8. Maintenance
None required.
9. Technical Services
Technical advice, custom CAD drawings,
and additional information can be
obtained by contacting Stego Industries’
technical assistance department or via
the website. www.stegoindustries.com
STEGO INDUSTRIES, LLC
Stego® Pre-Cut Pipe Boots
04/2013
TABLE 1: PHYSICAL PROPERTIES OF STEGO PRE-CUT PIPE BOOTS
PROPERTY TEST RESULTS
Under Slab Vapor Retarders ASTM E 1745 Class A, B & C – Standard Specification for Water Vapor Retarders Used
in Contact with Soil or Granular Fill under Concrete Slabs Exceeds Class A, B & C
Water Vapor Permeance ASTM F 1249 – Test Method for Water Vapor Transmission Rate Through Plastic Film and 0.0086 perms
Sheeting Using a Modulated Infrared Sensor *0.0036 WVTR
Puncture Resistance ASTM D 1709 – Test Methods for Impact Resistance of Plastic Film by Free-Falling
Dart Method 2266 grams
Tensile Strength ASTM D 882 – Test Method for Tensile Properties of Thin Plastic Sheeting 70.60 lbf/in.
Permeance After Conditioning ASTM E 154 Section 8, F 1249 – Permeance after wetting, drying, and soaking 0.0098 perms
(ASTM E 1745 ASTM E 154 Section 11, F 1249 – Permeance after heat conditioning 0.0091 perms
Sections 7.1.2 - 7.1.5) ASTM E 154 Section 12, F 1249 – Permeance after low temperature conditioning 0.0097 perms
ASTM E 154 Section 13, F 1249 – Permeance after soil organism exposure 0.0095 perms
Thickness ACI 302.1R-04 – Minimum Thickness (10 mils) 15 mils
Pipe Boot Dimensions 18" x 18"
Note: perm unit = grains/(ft2 *hr* in.Hg) * WVTR = Water Vapor Transmission Rate
4. Technical Data
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC.
UNDER-SLAB INSTRUCTIONS:
1. Stego Wrap can be installed over an aggregate, sand, or tamped earth
base. It is not necessary to have a cushion layer or sand base, as Stego
Wrap is tough enough to withstand rugged construction environments.
2. Unroll Stego Wrap over the area where the slab is to be placed. Stego
Wrap should completely cover the concrete placement area. All joints/
seams both lateral and butt should be overlapped a minimum of
six inches and taped using Stego Tape.
NOTE: The area of adhesion should be free from dust, dirt, moisture, and
frost to allow maximum adhesion of the pressure-sensitive tape.
3. ASTM E 1643 requires sealing the perimeter of the slab. Extend vapor
retarder over footings and seal to foundation wall, grade beam, or
slab at an elevation consistent with the top of the slab or terminate
at impediments such as waterstops or dowels. Consult the structural
engineer of record before proceeding.
SEAL TO SLAB AT PERIMETER:*
NOTE: Clean the surface of Stego Wrap to ensure that the area of adhesion is
free from dust, dirt, moisture, and frost to allow maximum adhesion of the
pressure-sensitive adhesive.
a. Install Crete Claw® on the entire perimeter edge of Stego Wrap.
b. Prior to the placement of concrete, ensure that the top of Crete Claw
is free of dirt, debris, or mud to maximize the bond to the concrete.
STEGO WRAP VAPOR BARRIER/RETARDERINSTALLATION INSTRUCTIONS
IMPORTANT: Please read these installation instructions completely, prior to beginning any Stego Wrap installation. The following
installation instructions are based on ASTM E 1643 - Standard Practice for Selection, Design, Installation, and Inspection of Water Vapor
Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs. If project specifications call for compliance with ASTM E 1643,
then be sure to review the specific installation sections outlined in the standard along with the techniques referenced in these instructions.
VAPOR BARRIER
STEGO® TAPE
Minimum 6” overlap
FIGURE 1: UNDER-SLAB INSTALLATION
PART 1
.)."'*,")&%%™-,,")+)",-()™lll#hiZ\d^cYjhig^Zh#Xdb
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC. 04/2013
NOTE: Stego Industries, LLC’s (“Stego”) installation instructions are based on ASTM E 1643 - Standard Practice for Selection, Design, Installation, and
Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs. These instructions are meant to be used as a
guide, and do not take into account specific job site situations. Consult local building codes and regulations along with the building owner or owner’s
representative before proceeding. If you have any questions regarding the above mentioned installation instructions or Stego products, please call us at
877-464-7834 for technical assistance. While Stego employees and representatives may provide technical assistance regarding the utility of a specific
installation practice or Stego product, they are not authorized to make final design decisions.
VAPOR BARRIER
CRETE CLAW®
SLAB PERIMETER
VAPOR BARRIER
FOOTING
STEGOTACK® TAPE
FIGURE 2a: SEAL TO SLAB AT PERIMETER
FIGURE 2b: SEAL TO PERIMETER WALL
STEGO LABOR SAVER!
This method not only complies with ASTM E 1643, but it also:
‹YLK\JLZSHIVYJVTWHYLK[VV[OLYWLYPTL[LYZLHSPUN[LJOUPX\LZ
‹JHUIL\ZLKL]LU^P[OV\[HUL_PZ[PUN^HSSVYMVV[PUN\USPRLHS[LYUH[P]LZ
OR SEAL TO PERIMETER WALL OR FOOTING WITH
STEGOTACK® TAPE:*
a. Make sure area of adhesion is free of dust, dirt, debris,
moisture, and frost to allow maximum adhesion.
b. Remove release liner on one side and stick to desired
surface.
c. When ready to apply Stego Wrap, remove the exposed
release liner and press Stego Wrap firmly against
StegoTack Tape to secure.
* If ASTM E 1643 is specified, consult with project architect
and structural engineer to determine which perimeter seal
technique should be employed for the project.
FIGURE 2c: SEAL TO FOOTING
VAPOR BARRIER
FOOTING
STEGOTACK® TAPE
OR
.)."'*,")&%%™-,,")+)",-()™lll#hiZ\d^cYjhig^Zh#Xdb
NOTE: Stego Industries, LLC’s (“Stego”) installation instructions are based on ASTM E 1643 - Standard Practice for Selection, Design, Installation, and
Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs. These instructions are meant to be used as a
guide, and do not take into account specific job site situations. Consult local building codes and regulations along with the building owner or owner’s
representative before proceeding. If you have any questions regarding the above mentioned installation instructions or Stego products, please call us at
877-464-7834 for technical assistance. While Stego employees and representatives may provide technical assistance regarding the utility of a specific
installation practice or Stego product, they are not authorized to make final design decisions.
MULTIPLE PIPE PENETRATION SEALING:
Multiple pipe penetrations in close proximity and very
small pipes may be sealed using Stego Wrap and Stego
Mastic for ease of installation (see figure 5, Multiple
Pipe Penetration Sealing).

STEGO® TAPE
STEGO® MASTICCOMPLETELY FILL ALL VOIDS
FIGURE 5: MULTIPLE PIPE PENETRATION SEALING
STEGO WRAP PIPE PENETRATION REPAIR DETAIL:
1: Install Stego Wrap around pipe penetrations by slitting/cutting material as needed. Try to minimize the void space created.
2: If Stego Wrap is close to pipe and void space is minimized then seal around pipe penetration with Stego Tape and/or Stego Mastic.
(See Figure 4a)
3: If detail patch is needed to minimize void space around penetration, then cut a detail patch to a size and shape that creates a six inch
overlap on all edges around the void space at the base of the pipe. Stego Pre-Cut Pipe Boots are also available to speed up the installation.
4: Cut an “X” the size of the pipe diameter in the center of the pipe boot and slide tightly over pipe.
5: Tape down all sides of the pipe boot with Stego Tape.
6: Seal around the base of the pipe using Stego Tape and/or Stego Mastic.
(See Figure 4b)
STEGO® TAPE
LARGE VOID SPACE CREATED
STEGO® MASTICSTEGO® TAPE
CUT AN “X” THE SIZE OFPIPE DIAMETER OR
STEGO®PRE-CUTPIPE BOOT
STEGO®PRE-CUTPIPE BOOT
STEGO®PRE-CUTPIPE BOOT
STEGO®PRE-CUTPIPE BOOT
FIGURE 4b: DETAIL PATCH FOR PIPE PENETRATION SEALING
MINIMAL VOID SPACE CREATED
STEGO® MASTICSTEGO® TAPE
OR
FIGURE 4a: PIPE PENETRATION SEALING
5. IMPORTANT: ALL PENETRATIONS MUST BE SEALED. All pipe, ducting, rebar, wire penetrations and block outs should
be sealed using Stego Wrap, Stego Tape and/or Stego Mastic (see figure 4a, Pipe Penetration Sealing).
STEGO® TAPE
DAMAGED AREA
STEGO® TAPE STEGO® TAPE
SMALL HOLEOR
FIGURE 3: SEALING DAMAGED AREAS
4. In the event that Stego Wrap is damaged during or after installation, repairs must be made. Stego Tape can be used
to repair small holes in the material. For larger holes, cut a piece of Stego Wrap to a size and shape that covers any
damage by a minimum overlap of six inches in all directions. Clean all adhesion areas of dust, dirt, moisture, and frost.
Tape down all edges using Stego Tape (see figure 3, Sealing Damaged Areas).
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC. 04/2013
CRAWL SPACE INSTALLATION INSTRUCTIONS:
1. Turn Stego Wrap up the foundation wall to a minimum height of six inches above the outside/exterior grade or in
compliance with local building codes and terminate with Stego Term Bar. To form a complete seal, apply StegoTack
Tape or a layer of Stego Mastic to the foundation wall prior to installing Stego Term Bar. Allow one hour for Stego
Mastic to cure prior to installing Stego Term Bar.
2. Seal Stego Wrap around all penetrations and columns using Stego Tape, StegoTack Tape, and/or Stego Mastic.
3. Place Stego Wrap directly over the crawl space floor. If rigid insulation is to be used, install Stego Wrap prior to
insulation (under insulation and between the foundation wall and insulation).
4. Overlap seams a minimum of six inches and seal with Stego Tape. Some codes require a minimum of a twelve inch
overlap. Check appropriate codes prior to installation.
4.
VAPOR BARRIER
STEGO® TAPE
SUBGRADE
STEGOTACK® TAPE
STEGO® TERM BAR
STEGO® TAPE
STEGOTACK® TAPE
FIGURE 6: CRAWL SPACE INSTALLATION
NOTE: Stego Wrap Vapor Barrier and Stego Tape are both available in white (as shown in illustration above).
INSTALLATION TIP:
1. For a cleaner look and to prevent against tenting of Stego Wrap at the foundation wall/foundation floor intersection,
consider mechanically fastening Stego Wrap to base of foundation wall in addition to the above mentioned wall
termination.
STEGO WRAP VAPOR BARRIER/RETARDERINSTALLATION INSTRUCTIONS
PART 2
.)."'*,")&%%™-,,")+)",-()™lll#hiZ\d^cYjhig^Zh#Xdb
NOTE: Stego Industries, LLC’s (“Stego”) installation instructions are based on ASTM E 1643 - Standard Practice for Selection, Design, Installation, and
Inspection of Water Vapor Retarders Used in Contact with Earth or Granular Fill Under Concrete Slabs. These instructions are meant to be used as a
guide, and do not take into account specific job site situations. Consult local building codes and regulations along with the building owner or owner’s
representative before proceeding. If you have any questions regarding the above mentioned installation instructions or Stego products, please call us at
877-464-7834 for technical assistance. While Stego employees and representatives may provide technical assistance regarding the utility of a specific
installation practice or Stego product, they are not authorized to make final design decisions.
Stego, the stegosaurus logo, Crete Claw, and StegoTack are all deemed to be registered and protectable trademarks of Stego Industries, LLC. 04/2013
RP Series
Radon Mitigation Fan
All RadonAway™ fans are specifically
designed for radon mitigation. RP Series
Fans provide superb performance, run
ultra-quiet and are attractive. They are ideal
for most sub-slab radon mitigation systems.
Features
• Energy efficient
• Ultra-quiet operation
• Meets all electrical code requirements
• Water-hardened motorized impeller
• Seams sealed to inhibit radon leakage
(RP140 & RP145 double snap sealed)
• RP140 and RP260 Energy Star® Rated
• ETL Listed - for indoor or outdoor use
• Thermally protected motor
• Rated for commercial and residential use
For Further Information Contact
Made in USA with US
and imported parts
All RadonAway inline radon fans are covered by our
5-year, hassle-free warranty
ETL Listed
9/12P/N 02008
MODEL P/N FAN DUCT
DIAMETER WATTS MAX.
PRESSURE“WC
TYPICAL CFM vs. STATIC PRESSURE WC
0”.5”1.0”1.5”2.0”
RP140*23029-1 4”15-21 0.8 135 70 ---
RP145 23030-1 4”41-72 2.1 166 126 82 41 3
RP260*23032-1 6”50-75 1.6 272 176 89 13 -
RP265 23033-1 6”91-129 2.3 334 247 176 116 52
RP380*28208 8”95-152 2.3 497 353 220 130 38
Model A B C
RP140 4.5”9.7”8.5”
RP145 4.5”9.7”8.5”
RP260 6”11.75”8.6”
RP265 6”11.75”8.6”
RP380 8”13.41”10.53”
*Energy Star® Rated
The World’s Leading
Radon Fan Manufaturer
RP Series
Installation Instructions
RadonAway
3 Saber Way Ward Hill, MA 01835
www.radonaway.com
3 Saber Way Ward Hill, MA 01835
P/N IN020-REV K 4/11
IN020 Rev K Page 2 of 8

RadonAway Ward Hill, MA.
Series Fan Installation Instructions
Please Read and Save These Instructions.

DO NOT CONNECT POWER SUPPLY UNTIL FAN IS COMPLETELY INSTALLED.
MAKE SURE ELECTRICAL SERVICE TO FAN IS LOCKED IN "OFF" POSITION.
DISCONNECT POWER BEFORE SERVICING FAN.

1. WARNING! Do not use fan in hazardous environments where fan electrical system could provide ignition to
combustible or flammable materials.
2. WARNING! Do not use fan to pump explosive or corrosive gases.
3. WARNING! Check voltage at the fan to insure it corresponds with nameplate.
4. WARNING! Normal operation of this device may affect the combustion airflow needed for safe operation of fuel
burning equipment. Check for possible backdraft conditions on all combustion devices after installation.
5. NOTICE! There are no user serviceable parts located inside the fan unit.
Do NOT attempt to open. Return unit to the factory for service.
6. All wiring must be performed in accordance with the National Fire Protection Association’s (NFPA)”National Electrical
Code, Standard #70”-current edition for all commercial and industrial work, and state and local building codes. All
wiring must be performed by a qualified and licensed electrician
7. WARNING! Do not leave fan unit installed on system piping without electrical power for more than 48 hours. Fan
failure could result from this non-operational storage.
8. WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

b) Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the service panel.

IN020 Rev K Page 3 of 8

INSTALLATION INSTRUCTIONS IN020 Rev K
RP Series
RP140 p/n 23029-1
RP145 p/n 23030-1
RP260 p/n 23032-1
RP265 p/n 23033-1
RP380 p/n 28208 1.0 SYSTEM DESIGN CONSIDERATIONS 1.1 INTRODUCTION The RP Series Radon Fans are intended for use by trained, professional Radon mitigators. The purpose of this instruction is to provide additional guidance for the most effective use of an RP Series Fan. This instruction should be considered as a supplement to EPA standard practices, state and local building codes and state regulations. In the event of a conflict, those codes, practices and regulations take precedence over this instruction. 1.2 ENVIRONMENTALS The RP Series Fans are designed to perform year-round in all but the harshest climates without additional concern for temperature or weather. For installations in an area of severe cold weather, please contact RadonAway for assistance. When not in operation, the fan should be stored in an area where the temperature is never less than 32 degrees F. or more than 100 degrees F. 1.3 ACOUSTICS The RP Series Fan, when installed properly, operates with little or no noticeable noise to the building occupants. The velocity of the outgoing air should be considered in the overall system design. In some cases the "rushing" sound of the outlet air may be disturbing. In these instances, the use of a RadonAway Exhaust Muffler is recommended.
(To ensure quiet operation of ENERGY STAR qualified in-line and remote fans, each fan shall be installed using sound attenuation techniques appropriate for the
installation. For bathroom and general ventilation applications, at least 8 feet of insulated flexible duct shall be installed between the exhaust or supply grille(s) and the fan). 1.4 GROUND WATER In the event that a temporary high water table results in water at or above slab level, water may be drawn into the riser pipes thus blocking air flow to the RP Series Fan. The lack of cooling air may result in the fan cycling on and off as the internal temperature rises above the thermal cutoff and falls upon shutoff. Should this condition arise, it is recommended that the fan be turned off until the water recedes allowing for return to normal operation. 1.5 SLAB COVERAGE The RP Series Fan can provide coverage up to 2000+ sq. ft. per slab penetration. This will primarily depend on the sub-slab material in any particular installation. In general, the tighter the material, the smaller the area covered per penetration. Appropriate selection of the RP Series Fan best suited for the sub-slab material can improve the slab coverage. The RP140/145/155 are best suited for general purpose use. The RP260 can be used where additional airflow is required and the RP265/380 is best suited for large slab, high airflow applications. Additional suction points can be added as required. It is recommended that a small pit (5 to 10 gallons in size) be created below the slab at each suction hole.
IN020 Rev K Page 4 of 8

1.6 CONDENSATION & DRAINAGE Condensation is formed in the piping of a mitigation system when the air in the piping is chilled below its dew point. This can occur at points where the system piping goes through unheated space such as an attic, garage or outside. The system design must provide a means for water to drain back to a slab hole to remove the condensation. The RP Series Fan MUST be mounted vertically plumb and level, with the outlet pointing up for proper drainage through the fan. Avoid mounting the fan in any orientation that will allow water to accumulate inside the fan housing. The RP Series Fans are NOT suitable for underground burial. For RP Series Fan piping, the following table provides the minimum recommended pipe diameter and pitch under several system conditions.
Pipe
Dia. Minimum Rise per Ft of Run*
@25 CFM @50 CFM @100 CFM @200 CFM @300 CFM
6" - 3/16 1/4 3/8 3/4
4" 1/8 1/4 3/8 2 3/8 -
3" 1/4 3/8 1 1/2 - -
*Typical RP1xx/2xx Series Fan operational flow rate is 25 - 90 CFM 0n 3” and 4” pipe.
(For more precision, determine flow rate by measuring Static Pressure, in WC, and
correlate pressure to flow in the performance chart in the addendum.)
Under some circumstances in an outdoor installation a condensate bypass should be installed in the outlet ducting as shown. This may be particularly true in cold climate installations which require long lengths of outlet ducting or where the outlet ducting is likely to produce large amounts of condensation because of high soil moisture or outlet duct material. Schedule 20 piping and other thin-walled plastic ducting and Aluminum downspout will normally produce much more condensation than Schedule 40 piping. The bypass is constructed with a 45 degree Wye fitting at the bottom of the outlet stack. The bottom of the Wye is capped and fitted with a tube that connects to the inlet piping or other drain. The condensation produced in the outlet stack is collected in the Wye fitting and drained through the bypass tube. The bypass tubing may be insulated to prevent freezing. 1.7 "SYSTEM ON" INDICATOR A properly designed system should incorporate a "System On" Indicator for affirmation of system operation. A manometer, such as a U-Tube, or a vacuum alarm is recommended for this purpose.
RUN
RISE

IN020 Rev K Page 5 of 8
1.8 ELECTRICAL WIRING The RP Series Fans operate on standard 120V 60 Hz. AC. All wiring must be performed in accordance with the National Fire Protection Association’s (NFPA)”National Electrical Code, Standard #70”-current edition for all commercial and industrial work, and state and local building codes. All wiring must be performed by a qualified and licensed electrician. Outdoor installations require the use of a U.L. listed watertight conduit. Ensure that all exterior electrical boxes are outdoor rated and properly sealed to prevent water penetration into the box. A means, such as a weep hole, is recommended to drain the box. 1.9 SPEED CONTROLS The RP Series Fans are rated for use with electronic speed controls, however, they are generally not recommended. If used, the recommended speed control is Pass & Seymour Solid State Speed Control Cat. No. 94601-I. 2.0 INSTALLATION The RP Series Fan can be mounted indoors or outdoors. (It is suggested that EPA recommendations be followed in choosing the fan location.) The RP Series Fan may be mounted directly on the system piping or fastened to a supporting structure by means of optional mounting bracket.

IN020 Rev K Page 6 of 8
2.1 MOUNTING Mount the RP Series Fan vertically with outlet up. Insure the unit is plumb and level. When mounting directly on the system piping assure that the fan does not contact any building surface to avoid vibration noise. 2.2 MOUNTING BRACKET (optional) The RP Series Fan may be optionally secured with the RadonAway P/N 25007-2 (25033 for RP385) mounting bracket. Foam or rubber grommets may also be used between the bracket and mounting surface for vibration isolation. 2.3 SYSTEM PIPING Complete piping run, using flexible couplings as means of disconnect for servicing the unit and vibration isolation. 2.4 ELECTRICAL CONNECTION Connect wiring with wire nuts provided, observing proper connections (See Section 1.8):
Fan Wire Connection
Green Ground
Black AC Hot
White AC Common
2.5 VENT MUFFLER (optional) Install the muffler assembly in the selected location in the outlet ducting. Solvent weld all connections. The muffler is normally installed at the end of the vent pipe. 2.6 OPERATION CHECKS _____ Verify all connections are tight and leak-free. _____ Insure the RP Series Fan and all ducting is secure and vibration-free. _____ Verify system vacuum pressure with manometer. Insure vacuum pressure is less than maximum recommended operating pressure (Based on sea-level operation, at higher altitudes reduce by about 4% per 1000 Feet.) (Further reduce Maximum Operating Pressure by 10% for High Temperature environments)
See Product Specifications. If this is exceeded, increase the number of suction points. _____ Verify Radon levels by testing to EPA protocol.

Typical Indoor Installation
IN020 Rev K Page 7 of 8
RP SERIES PRODUCT SPECIFICATIONS The following chart shows fan performance for the RP Series Fan:
Typical CFM Vs Static Pressure "WC
0" .25" .5" .75" 1.0" 1.25" 1.5" 1.75" 2.0"
RP140 135 103 70 14 - - - - -
RP145 166 146 126 104 82 61 41 21 3
RP260 272 220 176 138 103 57 13 - -
RP265 334 291 247 210 176 142 116 87 52
RP380* 497 401 353 281 220 176 130 80 38
* Tested with 6” inlet and discharge pipe.
Power Consumption
120 VAC, 60Hz 1.5 Amp Maximum
Maximum Recommended
Operating Pressure* (Sea Level Operation)**
RP140 17 - 21 watts RP140 0.8" W.C.
RP145 41 - 72 watts RP145 1.7" W.C.
RP260 52 - 72 watts RP260 1.5" W.C.
RP265 91 - 129 watts RP265 2.2" W.C.
RP380 95 - 152 watts RP380 2.0" W.C.
*Reduce by 10% for High Temperature Operation
**Reduce by 4% per 1000 feet of altitude
Size Weight Inlet/Outlet
RP140 8.5H" x 9.7" Dia. 5.5 lbs. 4.5" OD (4.0" PVC Sched 40 size compatible)
RP145 8.5H" x 9.7" Dia. 5.5 lbs. 4.5" OD (4.0" PVC Sched 40 size compatible)
RP260 8.6H" x 11.75" Dia. 5.5 lbs. 6.0” OD
RP265 8.6H" x 11.75" Dia. 6.5 lbs. 6.0” OD
RP380 10.53H" x 13.41" Dia. 11.5 lbs. 8.0” OD

Recommended ducting: 3" or 4" RP1xx/2xx, 6” RP380, Schedule 20/40 PVC Pipe
Mounting: Mount on the duct pipe or with optional mounting bracket.
Storage temperature range: 32 - 100 degrees F.
Normal operating temperature range: -20 - 120 degrees F.
Maximum inlet air temperature: 80 degrees F.
Continuous Duty
Class B Insulation
Thermally Protected
3000 RPM
Rated for Indoor or Outdoor Use

RP140 and RP260
Only.

IN020 Rev K Page 8 of 8
IMPORTANT INSTRUCTIONS TO INSTALLER

Inspect the GP/XP/XR/RP Series Fan for shipping damage within 15 days of receipt. Notify
RadonAway of any damages immediately. Radonaway is not responsible for damages incurred
during shipping. However, for your benefit, Radonaway does insure shipments.

There are no user serviceable parts inside the fan. Do not attempt to open. Return unit to factory
for service.

Install the GP/XP/XR/RP Series Fan in accordance with all EPA standard practices, and state and local building codes and state regulations.
WARRANTY
Subject to any applicable consumer protection legislation, RadonAway warrants that the GPX01/XP/XR/RP Series Fan (the “Fan”) will be free from
defects in materials and workmanship for a period of 90 days from the date of purchase (the “Warranty Term”).
RadonAway will replace any Fan which fails due to defects in materials or workmanship. The Fan must be returned (at Owner’s cost) to the
RadonAway factory. Any Fan returned to the factory will be discarded unless the Owner provides specific instructions along with the Fan when it is
returned regardless of whether or not the Fan is actually replaced under this warranty. Proof of purchase must be supplied upon request for
service under this Warranty.
This Warranty is contingent on installation of the Fan in accordance with the instructions provided. This Warranty does not apply where any
repairs or alterations have been made or attempted by others, or if the unit has been abused or misused. Warranty does not cover damage in
shipment unless the damage is due to the negligence of RadonAway.
5 YEAR EXTENDED WARRANTY WITH PROFESSIONAL INSTALLATION.
RadonAway will extend the Warranty Term of the fan to 5 years from date of manufacture if the Fan is installed in a professionally designed andprofessionally installed radon system or installed as a replacement fan in a professionally designed and professionally installed radon system.Proof of purchase and/or proof of professional installation may be required for service under this warranty. Outside the Continental United States
and Canada the extended Warranty Term is limited to one (1) year from the date of manufacture.
RadonAway is not responsible for installation, removal or delivery costs associated with this Warranty.
EXCEPT AS STATED ABOVE, THE GPx01/XP/XR/RP SERIES FANS ARE PROVIDED WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION,IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL RADONAWAY BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES ARISING OUT OF, OR RELATING TO, THE FAN OR THEPERFORMANCE THEREOF. RADONAWAY’S AGGREGATE LIABILITY HEREUNDER SHALL NOT IN
ANY EVENT EXCEED THE AMOUNT OF THE PURCHASE PRICE OF SAID PRODUCT. THE SOLE AND
EXCLUSIVE REMEDY UNDER THIS WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF THE
PRODUCT, TO THE EXTENT THE SAME DOES NOT MEET WITH RADONAWAY’S WARRANTY AS
PROVIDED ABOVE.
For service under this Warranty, contact RadonAway for a Return Material Authorization (RMA) number and shipping
information.  No returns can be accepted without an RMA.  If factory return is required, the customer assumes all shipping
cost to and from factory.
RadonAway
3 Saber Way
Ward Hill, MA 01835TEL. [phone]
FAX [phone]
Record the following information for your records:
Serial No.
Purchase Date