23055 - Battery and Ignition_Area C and D VIMS Install

VIMS Installation Report –
Area C and Area D
Ello House

Battery & Ignition Distribution
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
Brownfields Project No. 23055-19-060

March 26, 2024
H&H Job No. PDP.001

#C-1269 Engineering
#C-245 Geology

i

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
VIMS Installation Report – Area C and Area D
Battery & Ignition Distribution
Ello House
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
Brownfields Project No. 23055-19-060
H&H Job No. PDP.001

Table of Contents

1.0 Introduction ................................................................................................................ 1 
2.0 VIMS Installation Inspections and Influence Testing ............................................ 4 
2.1 VIMS Installation......................................................................................................4 
2.2 VIMS Pilot Influence Testing ...................................................................................6 
3.0 VIMS Effectiveness Sampling Activities .................................................................. 8 
3.1 Indoor Air Sampling .................................................................................................8 
3.2 Indoor Air Sampling Results ....................................................................................9 
3.3 Sub-Slab Soil Gas Sampling ...................................................................................10 
3.4 Sub-Slab Soil Gas Sampling Results ......................................................................12 
3.5 Vapor Intrusion Risk Evaluation ............................................................................12 
4.0 Summary and Conclusions ..................................................................................... 14 

List of Tables

Table 1 Summary of Indoor Air Analytical Results (Area C & D)
Table 2 Summary of Sub-Slab Soil Gas Analytical Results (Area C & D)

List of Figures

Figure 1 Site Location Map
Figure 2 Site Map

ii

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
List of Appendices

Appendix A Site Development Phasing Plan
Appendix B VIMS As-Built Drawings (VM-1, VM-2, VM-3, and VM-4)
Appendix C Product Specifications
Appendix D Photographic Log and Inspection Checklist
Appendix E VIMS Influence Testing Forms and Sampling Field Forms
Appendix F Laboratory Analytical Report
Appendix G Safety Data Sheets
Appendix H DEQ Risk Calculators

1

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
VIMS Installation Report – Area C and Area D
Battery & Ignition Distribution
Ello House
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
Brownfields Project No. 23055-19-060
H&H Job No. PDP.001

1.0 Introduction

On behalf of 3615 Tryclan, LP (Prospective Developer or PD), Hart & Hickman, PC (H&H) has
prepared this report to document vapor intrusion mitigation system (VIMS) installation
inspections, VIMS influence testing, and VIMS efficacy sampling activities completed for Area C
and Area D of the Ello House apartment building on the Battery & Ignition Distribution
Brownfields Property (Brownfields Project No. 23055-19-060) located at 3615 Tryclan Drive in
Charlotte, Mecklenburg, North Carolina (Site). A Site location map is included as Figure 1, and
the Site and surrounding area are shown in Figure 2.

Redevelopment of the Site is nearing completion and includes construction of a residential
apartment building. The apartment building is one interconnected building, but it is being
completed in stages due to turnover timelines. For simplicity, the building has been divided into
five separate turnover areas named A1, A2, B, C, and D, which are depicted on the Site
development phasing plan in Appendix A and on Sheets VM-3 and VM-4 in Appendix B. Areas
A1, A2, and B have been completed, as documented in the VIMS Installation Report-Area A1 LoSo
Village Apartments, dated August 14, 2023, and the VIMS Installation Report-Area A2 and Area
B Ello House, dated February 9, 2024. Occupancy compliance approval was received for Area A1
in a letter dated September 15, 2023, and for Areas A2 and B in a letter dated February 13, 2024.
This report applies to the VIMS installation in the Area C and Area D portions of the building.

To address potential environmental concerns in connection with the Site, a Brownfields Agreement
between the North Carolina Department of Environmental Quality (DEQ) and the PD was recorded
on January 19, 2022. Land Use Restriction (LUR) 14.h. included in the Brownfields Agreement
generally states that no enclosed building may be constructed on the property until DEQ
2

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
determines in writing that the building would be protective of users from risks of potential vapor
intrusion. In accordance with LUR 14.h. in the Brownfields Agreement for the Site, H&H
prepared a Vapor Intrusion Mitigation Plan (VIMP) – Revision 1 dated September 3, 2021, which
was subsequently approved by DEQ Brownfields on September 9, 2021.

The DEQ-approved VIMP includes installation of a VIMS during construction of the building to
minimize the potential for vapor intrusion into the building using a passive sub-slab vapor
extraction system. The VIMS consists of a network of sub-slab horizontal collection piping,
vertical exhaust risers connected to syphon ventilators on the building roof, and vapor barrier
below the concrete slabs and along retaining walls. The VIMS as-built drawings depicting the
installed VIMS components are included as Appendix B.

H&H completed VIMS inspections, VIMS influence testing, and VIMS efficacy testing for the
Area C and Area D building spaces in general accordance with the DEQ-approved VIMP. A
summary of the VIMS installation and influence testing activities is provided in Section 2.0. The
VIMS efficacy sampling activities and results are detailed in Section 3.0, and a summary and
conclusions based on the installation activities, influence testing, and efficacy sampling are
provided in Section 4.0.

Engineer’s Certification
According to the DWM Vapor Intrusion Guidance: “Risk-based screening is used to identify sites
or buildings likely to pose a health concern, to identify buildings that may warrant immediate
action, to help focus site-specific investigation activities or to provide support for building
mitigation and other risk management options including remediation.” In addition, the VIMP for
this Site was prepared to satisfy the standard vapor intrusion mitigation provisions in the
Brownfields Agreement. Per the North Carolina Brownfields Property Reuse Act 130A-310.32, a
prospective developer, with the assistance of H&H for this project, is to provide DEQ with
“information necessary to demonstrate that as a result of the implementation of the brownfields
agreement, the brownfields property will be suitable for the uses specified in the agreement while
fully protecting public health and the environment instead of being remediated to unrestricted use
3

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
standards.” It is in the context of these risk-based concepts that the H&H professional engineer
makes the following statement:

The Vapor Intrusion Mitigation System (VIMS) detailed herein is designed to mitigate intrusion
of subsurface vapors into the subject building from known Brownfields Property contaminants in
a manner that is in accordance with the most recent and applicable guidelines including, but not
limited to, DWM Vapor Intrusion Guidance, Interstate Technology & Regulatory Council (ITRC)
guidance, and American National Standards Institute (ANSI)/American Association of Radon
Scientists and Technologists (AARST) standards. The sealing professional engineer below is
satisfied that the design and its installation are fully protective of public health from known
Brownfields Property contaminants.

[SEAL]

4

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
2.0 VIMS Installation Inspections and Influence Testing

The VIMS in Area C and Area D each operate as separate, interconnected sub-slab vapor extraction
mitigation areas. The VIMS mitigation areas include a permeable gravel layer, sub-slab vapor
collection piping, a vapor barrier (vapor liner), riser piping, and wind-driven syphon ventilators.
As-built drawings depicting the layout of the VIMS (VM-4) and the system specifications and
details (VM-1 and VM-2) are provided in Appendix B. Product specifications for the VIMS
components are included in Appendix C.

2.1 VIMS Installation

Between September 2022 and August 2023, H&H conducted inspections under direction of a
North Carolina (NC) Professional Engineer (PE) during various phases of construction to verify
that the VIMS was installed in accordance with the DEQ-approved VIMP. Inspections were
completed for the VIMS during the following phases of installation:

(1) Inspection of the base course gravel layer, sub-slab piping layout, and monitoring
points prior to installing the vapor barrier;
(2) Inspection of the vapor barrier prior to pouring concrete;
(3) Inspection of above-grade vertical riser piping; and
(4) Inspection of syphon ventilators and riser pipe connections.

A representative photographic log of installed VIMS components along with inspection checklists
are provided in Appendix D. Based on observations made during the VIMS inspections, the
VIMSs for the Area C and Area D portions of the building were installed in general accordance
with the DEQ-approved VIMP. A brief summary of the main VIMS components is provided in
the following paragraphs for the Area C and Area D portions of the building.

The DEQ-approved VIMP included installation of Vaporblock® Plus 20 (VBP20) vapor barrier
manufactured by Viaflex Inc. (Viaflex), beneath the concrete slab-on-grade in Area C and Area D.
VBP20 is an ASTM-certified 20-mil, multi-layer, chemically resistant vapor barrier, designed to
5

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
prevent the migration of volatile organic compounds. Technical specifications and installation
instructions obtained from Viaflex for the VBP20 vapor barrier are provided in Appendix C.

The vapor barrier was installed per manufacturer installation instructions (Appendix C). Briefly,
VBP20 was installed by the construction contractor to cover the ground surface below the entire
area of the ground floor slab. Seams within the building footprint have a minimum 12-inch overlap
and were sealed with VaporSeal™ tape. Small puncture holes and utility penetrations were sealed
with VaporSeal™ tape.

In addition to the vapor barrier, the VIMS also includes vapor extraction components beneath the
ground-level concrete slab to reduce the potential for vapor intrusion into the building. Sub-slab
vapor extraction is accomplished using 3-inch schedule 40 PVC piping. The sub-slab vapor
extraction piping is connected to riser piping which extends to the roof. The passive VIMS is
enhanced with Empire Model SV04SS (Stainless Steel) syphon ventilators installed on the
discharge end of the exhaust stacks on the roof. The vent systems in each area are interconnected
to allow for continued depressurization below the building slabs in the event that active fans are
installed in the future or the syphon ventilator is damaged between yearly inspections. Product
specification sheets for the stationary ventilator and slotted piping are included in Appendix C.

To further enhance sub-slab vapor transmission and collection effectiveness, a uniform layer of
high permeability stone (clean #57) was installed directly below the concrete slab to allow for air
movement beneath the entirety of the slab. Sub-slab 3-inch Schedule 40 PVC piping was installed
within the high permeability stone layer. The thickness of the high permeability stone around the
PVC piping extends a minimum of 2 inches below the piping, and the top of the PVC piping is set
flush with the completed stone layer, or approximately 1-inch below the top of the stone. In areas
without piping, a minimum thickness of 4 inches of clean stone was installed.

To complete influence testing and in the event the system needs to be activated with electric fans,
vacuum monitoring points were installed in Area C and Area D to measure the pressure differential
between indoor air and the sub-slab, and for collection of sub-slab soil gas samples. Area C has
two permanent monitoring points (MP-4 and MP-5) and one temporary monitoring point (TMP-
6

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
3); Area D has one permanent vacuum monitoring point installed (MP-3) and one temporary
monitoring point (TMP-4). The locations of the monitoring points are depicted on as-built drawing
VM-4 provided in Appendix B.

Based on inspections completed during the VIMS installation activities, the VIMS was installed
in general accordance with the DEQ-approved VIMP. VIMS details and specifications and VIMS
as-built drawings are included in Appendix B. A representative photographic log of the installed
VIMS components is provided in Appendix D.

2.2 VIMS Pilot Influence Testing

In accordance with the DEQ-approved VIMP, on March 29, March 30, and August 24, 2023, post-
installation VIMS pilot influence testing was conducted after the concrete slabs had been poured
to evaluate sub-slab vacuum communication across mitigated areas and verify that sufficient
depressurization can be achieved should electric fans be needed in the future. During testing, H&H
connected electric fans to the vertical riser piping to model an active sub-slab depressurization
system. Differential pressure measurements were collected at corresponding vacuum monitoring
points using a Dwyer series 475 Mark III digital manometer (capable of measuring to 0.001 inches
of water column [in-WC] or 0.25 Pa) to establish baseline conditions prior to use of the electric
fans. Following collection of baseline differential pressure measurements, the electric fans were
turned on and differential pressure measurements were collected at each monitoring point and fan.
A pressure differential resulting in depressurization below the slab of at least 4 pascals
(approximately 0.016 in-WC) at remote distances from riser locations in each VIMS treatment
area is generally considered sufficient evidence for adequate sub-slab depressurization.

The pilot influence test results are provided in Appendix E. Please note that the influence testing
for Area C and Area D was conducted concurrently with testing in other portions of the building.
The table below identifies the fans and monitoring points used to evaluate the two areas and
provides a summary of the monitoring point differential pressure ranges observed in the Area C
and Area D portions of the building during the pilot testing. Fan and monitoring point locations
are depicted on VM-4 in Appendix B.

7

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
Test Area Associated
Fan Locations
Associated Monitoring
Points
Differential
Pressure Range
(in-WC)
Area C E-5, E-6, and E-7 MP-4, MP-5, and TMP-3 -0.232 to -1.292
Area D E-3, E-4 MP-3, TMP-4 -0.363 to -0.810

The influence test results indicate that adequate connection from the risers to each corresponding
area of the sub-slab annular space is present and that adequate sub-slab communication with
vacuum influence greater 0.016 in-WC (4 pascals) is achievable in each area should active sub-
slab depressurization be warranted in the future.
8

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
3.0 VIMS Effectiveness Sampling Activities

Following successful installation of the VIMS, H&H collected co-located indoor air and sub-slab
soil gas samples from select locations within the footprint of the Area C and Area D portions of
the building to evaluate risks to future building occupants. The samples were collected in general
accordance with the DEQ-approved VIMP and the DEQ DWM Vapor Intrusion Guidance
(Guidance) dated March 2018. Details of the indoor air and sub-slab soil gas sampling activities
and results are provided in the following sections.

3.1 Indoor Air Sampling

On February 20 to February 21, 2024, H&H collected two (2) indoor air samples (C-IAS-1 and D-
IAS-1) from the Area C and Area D portions of the building after the building was enclosed (all
exterior doors and windows installed) and the VIMS was installed. In accordance with the DEQ-
approved VIMP, the indoor air sampling was conducted prior to installation of the heating,
ventilation, and air conditioning (HVAC) equipment. The indoor air samples were collected using
a laboratory-supplied individually-certified 6-liter Summa canister over a 24-hour period and were
analyzed for select volatile organic compounds (VOCs) by EPA Method TO-15. The select VOC
list was based on the compounds detected within the sub-slab vapor samples and compounds
previously detected on the property. DEQ approved the indoor air analyte list via e-mail on March
4, 2024.

The indoor air samples were collected prior to the sub-slab soil gas sampling described in
Section 3.3 below. The indoor air samples were collected from residential units 148 (C-IAS-1)
and 133 (D-IAS-1). The syphon ventilators were installed a minimum of two weeks prior to the
sampling event.

For QA/QC purposes, one duplicate indoor air sample (IAS-DUP) was collected during the
sampling event using a laboratory-supplied stainless-steel sample “T” fitting. One background
ambient air sample (IAS-BKG) was also collected. The location of the outdoor background air
sample was determined on the day of sampling based on the prevailing wind direction on that day
and was collected south of the Area D portion of the building.
9

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx

The Summa canisters were deployed on raised sampling platforms which placed the sample intake
at a height consistent with the breathing zone (approximately 5 ft above grade). The approximate
locations of the pre-occupancy indoor air samples are depicted on the as-built drawing (VM-4 in
Appendix B).

Periodic checks were conducted by H&H to monitor the pressure within the Summa canisters to
confirm adequate sample volume was collected. During the sampling activities, indoor/outdoor
air pressure differential was measured several times, including at the start and end of the 24-hour
sampling period using a manometer sensitive to 0.001 inches of water column. In addition, exterior
wind speed, wind direction, barometric pressure, indoor/outdoor temperature, and precipitation (if
any) were recorded near the start and end of the sampling period. H&H also completed a DEQ
Indoor Air Building Survey and Sampling Form (Appendix C of the DWM VI Guidance) to record
sample information and building and individual unit conditions at the time of sampling.

The canisters were labeled with the sample identification, beginning and ending times, and the
requested analysis. The canisters were then placed in laboratory-supplied shipping containers and
delivered to Waypoint Analytical, LLC (Waypoint) under standard chain of custody protocols for
analysis of select VOCs. As indicated in the laboratory reports, J-flag estimated concentrations
were reported by the laboratory. The completed building survey and sampling forms are included
in Appendix E, and the laboratory analytical report and chain of custody form are included in
Appendix F.

3.2 Indoor Air Sampling Results

The indoor air sample analytical results are summarized in Table 1, and the laboratory analytical
report with chain of custody record is provided in Appendix F. The indoor air sample laboratory
analytical results were compared to the DEQ Residential Indoor Air Screening Levels (IASLs)
dated February 2024.

The indoor air analytical results indicate that several compounds were detected above laboratory
method detection limits (MDLs) in the Area C and Area D portions of the building. Four
10

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
constituents (benzene, ethylbenzene, naphthalene, and total xylenes) were detected at
concentrations above the Residential IASLs. Benzene (ranging from 1.20 J micrograms per cubic
meter [µg/m3] to 2.29 µg/m3) was detected at estimated concentrations in each of the indoor air
samples above the Residential IASL of 0.36 µg/m3. Benzene was also detected above the
Residential IASL in the background air sample (0.897 J µg/m3) and is likely attributed to vehicular
traffic. Ethylbenzene (ranging from 1.81 J µg/m3 to 3.23 µg/m3) was detected in each of the indoor
air samples at concentrations above the Residential IASL of 1.1 µg/m3. Naphthalene (0.571 J
µg/m3 and 0.560 J µg/m3) was detected at estimated concentrations in the Area C indoor air sample
(C-IAS-1) and associated duplicate sample (IAS-DUP) above the Residential IASL of 0.083
µg/m3. Total xylenes (23.5 µg/m3 and 23.9 µg/m3) were detected in the Area C indoor air sample
(C-IAS-1) and associated duplicate sample (IAS-DUP) at concentrations above the Residential
IASL of 21 µg/m3.

Tetrachloroethylene (PCE) and trichloroethylene (TCE) were not detected at concentrations above
the laboratory method detection limits in the indoor air samples (or duplicate) collected from
Area C and Area D.

Benzene, ethylbenzene, naphthalene, and xylenes are common components of building materials
and/or gasoline products, as listed in the Safety Data Sheets (SDS) that were provided to H&H for
building materials and products used during construction of the building (Appendix G). The use
of these materials likely contributed to the detected indoor air concentrations of benzene,
ethylbenzene, naphthalene, and xylenes. In addition, these compounds were detected at lower (or
similar) concentrations in the sub-slab soil gas samples (see Table 2) suggesting the indoor air
concentrations are attributable to an above-slab source and are not associated with vapor intrusion.

3.3 Sub-Slab Soil Gas Sampling

The DEQ-approved VIMP specified the collection of two sub-slab soil gas samples from
monitoring points MP-4 and MP-5 in Area C and one sub-slab soil gas sample from MP-3 in
Area D. However, immediately before the sampling event, MP-4 was observed to have been
recently repaired with PVC glue, which would impact the sampling results and laboratory
reporting limits. H&H contacted DEQ, and DEQ agreed that MP-4 could be omitted from the pre-
11

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
occupancy sampling event and sampled during the first-occupancy sampling event. H&H
collected the sub-slab vapor samples from Area C (MP-5) and Area D (MP-3) on February 21,
2024 (after indoor air sampling was completed). The sub-slab soil gas sample locations are shown
on Sheet VM-4 in Appendix B.

During the sub-slab soil gas sampling event, one duplicate sub-slab soil gas sample was collected
for quality assurance/quality control (QA/QC) purposes. MP-DUP was collected from location
MP-5 for Area D. The duplicate sub-slab soil gas sample was collected utilizing a laboratory-
supplied stainless-steel sampling “T” which allows for the simultaneous collection of two sub-slab
soil gas samples from a monitoring point.

At each sample location, a temporary expandable plug with a quick-connect sampling port was
placed within the monitoring point to create an air-tight seal. Teflon sample tubing was then
secured to the sampling port and connected to an airflow regulator and laboratory-supplied
batch-certified 1.4-liter stainless steel Summa canister. The airflow regulator was preset by the
laboratory to collect the sample at a flow rate of approximately 140 milliliters per minute.

Prior to sample collection, H&H conducted a leak test at each monitoring point by placing a shroud
around the monitoring point and sampling train including the Summa canister. The air within the
shroud was flooded with helium vapor and concentrations were measured with a calibrated helium
detector. Helium concentrations within the shroud were maintained between approximately 12%
and 13%. A small air pump was connected to the sample tubing outside of the shroud and used to
purge a minimum of three sample train volumes into a Tedlar® bag at each sampling point. The
helium detector was used to measure helium concentrations within the Tedlar® bag sample to
confirm helium concentrations in the sample were less than 10% of that measured within the
shroud. Results of the helium leak checks indicate that short-circuiting at the monitoring points
or within the sampling train was not present. Sub-slab soil gas sampling field forms completed by
sampling personnel are included in Appendix E.

Following a successful leak check, the air flow regulators were opened to allow collection of the
sub-slab soil gas samples. Vacuum in the Summa canisters was monitored during the sampling
12

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
event to confirm adequate sample volume was collected at each monitoring point. Upon
completion of sample collection, the air flow regulator to the Summa canister was closed. The
canisters were labeled with the sample identification, the beginning and ending times, the pressure
measurements, and the requested analysis. The canisters were then placed in laboratory-supplied
shipping containers and delivered to Waypoint under standard chain of custody protocols for
analysis of VOCs by EPA Method TO-15 (full list).

3.4 Sub-Slab Soil Gas Sampling Results

The sub-slab soil gas sample analytical results are summarized in Table 2, and the laboratory
analytical report with chain of custody record are provided in Appendix F. The sub-slab soil gas
sample laboratory analytical results were compared to the DEQ Residential Sub-Slab and Exterior
Soil Gas Screening Levels (SGSLs) dated February 2024.

Several VOCs were detected in each sample collected from Areas C and D at concentrations above
laboratory MDLs but below the Residential SGSLs. One constituent, tetrahydrofuran, was detected
at a concentration of 14,200 µg/m3 in the Area D sample location (MP-3), which slightly exceeded
the Residential SGSL of 14,000 µg/m3. Tetrahydrofuran is a component of PVC primer and glue,
as listed in the Safety Data Sheets (SDS) that were provided to H&H for building materials and
products used during construction of the building (Appendix G). The detected concentration of
tetrahydrofuran is attributable to the use of these materials.

PCE and TCE were not detected at concentrations above the laboratory method detection limits in
the sub-slab soil gas samples (or duplicate) collected from Area C and Area D.

3.5 Vapor Intrusion Risk Evaluation

The DEQ vapor intrusion screening levels are conservative and based on a target carcinogenic risk
(TCR) of 1 x 10-6 and a non-carcinogenic target hazard quotient (THQ) of 0.2. The DEQ
acceptable risk level for potential carcinogenic risks is a cumulative lifetime incremental cancer
risk (LICR) of 1 x 10-4 or less and the acceptable risk level for non-carcinogenic risks is a
cumulative hazard index (HI) of 1 or less.
13

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx

H&H utilized the DEQ Risk Calculator (February 2024) to further evaluate potential vapor
intrusion risks at the Site. H&H modeled a “worst-case” scenario by using the highest
concentrations of any compound detected in the February 2024 samples from both Area C and
Area D to conservatively evaluate potential vapor intrusion risks for a residential use scenario.
The calculated worst-case cumulative LICR and HI values for the indoor air and sub-slab soil gas
are provided in Table 1 and Table 2, and a copy of the completed DEQ Risk Calculator is provided
in Appendix H.

As shown in Table 1 and Table 2, results of the worst-case risk calculations for a residential use
scenario in Area C and Area D indicate a calculated cumulative LICR of 5.8 x10-7 and a HI value
of 0.23 for sub-slab soil gas and a calculated cumulative LICR of 1.6 x10-5 and a HI value of 0.82
for indoor air. The calculated cumulative residential use LICRs and HI values are within the DEQ
acceptable levels.

Based on this evaluation, the analytical samples do not indicate that there is unacceptable vapor
intrusion risk from Site contaminants to the occupants of the Area C or Area D portions of the
building, and no further pre-occupancy sampling is warranted.
14

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
4.0 Summary and Conclusions

Installation of the VIMS has been completed for the Area C and Area D turnover portions of the
Ello House multi-family apartments on the Battery & Ignition Distribution Brownfields Property.
Results of installation inspections, influence testing, and effectiveness sampling activities indicate
that the VIMS has been successfully installed in general accordance with the DEQ-approved
VIMP.

During construction of the Area C and Area D portions of the building, H&H conducted VIMS
installation inspections to confirm the system was installed as designed and completed post-
installation influence testing and indoor air and/or sub-slab soil gas sampling activities to evaluate
the efficacy of the systems. The VIMS installation inspections and post-installation testing
activities were completed in general accordance with the DEQ-approved VIMP. A summary of
the VIMS installation and post-installation efficacy assessment activities is provided below.

VIMS Installation
VIMS installation has been completed for the Area C and Area D portions of the building. The
VIMS in each area consists of a passive sub-slab venting system with vertical extraction piping to
the roof connected to wind-driven syphon ventilators. During installation of the VIMS, H&H
personnel, under the direction of a North Carolina licensed Professional Engineer, conducted
inspections during each stage of installation. Results of the installation inspections indicate that
the VIMS was successfully installed in general accordance with the DEQ-approved VIMP.

Sub-Slab Vacuum Influence
H&H completed vacuum influence pilot testing in March 2023. Differential pressure
measurements collected during the pilot test activities for Area C (ranging from -0.232 in-WC to
-1.292 in-WC) and Area D (ranging from -0.363 in-WC to -0.810 in-WC) indicate that adequate
vacuum communication beneath the slab was achieved. Based on these results, sufficient vacuum
(greater than 0.016 in-WC differential pressure) can be achieved by vacuum fans if an active
system is needed in the future.

15

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
Indoor Air Assessment
Following installation of the VIMS, H&H collected one indoor air sample and one duplicate from
the Area C portion of the building and one indoor air sample from the Area D portion of the
building to evaluate potential vapor intrusion risks. Laboratory analytical results of the indoor air
samples indicated that benzene, ethylbenzene, naphthalene, and total xylenes were detected at
concentrations above the Residential IASLs. H&H utilized the DEQ Risk Calculator (February
2024) to calculate the cumulative carcinogenic and non-carcinogenic risks under a hypothetical
worst-case residential-use scenario by utilizing the highest concentration of each compound
detected from both areas. The hypothetical worst-case residential use risk calculator results
indicate a cumulative LICR of 1.6 x 10-5 and a HI value of 0.82. The LICR and HI are within the
acceptable risk levels, which indicates that there is no unacceptable vapor intrusion risk from Site
contaminants to the occupants of the Area C and Area D portions of the building. No further pre-
occupancy sampling is warranted.

Sub-Slab Soil Gas Assessment
H&H collected one sub-slab soil gas sample (and duplicate) from Area C and one sub-slab soil gas
sample from Area D to evaluate potential vapor intrusion risks in each building area. Laboratory
analytical results of the sub-slab soil gas samples indicate tetrahydrofuran was detected above the
DEQ Residential SGSL in Area D, but is attributable to the recent use of PVC glue and primer at
the Site. H&H utilized the DEQ Risk Calculator (February 2024) to calculate the cumulative
carcinogenic and non-carcinogenic risks under a hypothetical worst-case residential-use scenario
by utilizing the highest concentration of each compound detected in the sub-slab soil gas samples.
The hypothetical worst-case risk calculator results indicate a cumulative LICR of 5.8 x 10-7 and a
HI value of 0.23 for residential use. The LICR and HI are within the acceptable risk levels. Based
on the evaluation, the analytical sample results do not indicate that there is unacceptable vapor
intrusion risk from Site contaminants to the occupants of the Area C and Area D portions of the
building. No further pre-occupancy sampling is warranted in these areas.

Conclusions
Based on the VIMS installation inspections, influence testing, and post-installation sub-slab soil
gas and indoor air sampling results, the VIMS is effectively mitigating potential vapor intrusion
16

https://harthick.sharepoint.com/sites/masterfiles-1/shared documents/aaa-master projects/proffitt dixon - pdp/pdp-001 -
tryclan avenue/vims install report/areas c and d/23055 - battery and ignition_area c and d vims install.docx
risks within the Area C and D portions of the building and is operating as designed. In accordance
with the DEQ-approved VIMP, post-occupancy sub-slab soil gas sampling for Area C and Area D
will be completed in the summer of 2024 and then on a semi-annual basis for future events. The
first post-occupancy sampling event for the entire Ello House apartment building is scheduled for
May 2024, as approved by DEQ in an email dated March 14, 2024. The post-occupancy sampling
events will be performed in accordance with the procedures outlined in the VIMP, and the results
will be reported to DEQ. If semi-annual sampling results indicate consistent or decreasing
concentrations within acceptable risk levels, a request to modify or terminate sampling will be
submitted for DEQ approval.

Based on the pre-occupancy sampling results and in accordance with the DEQ-approved VIMP,
we are requesting DEQ approval not to conduct post-occupancy indoor air sampling, unless the
post-occupancy soil gas sampling results indicate cumulative risks greater than 1 x 10-4 for
carcinogenic risks and/or a hazard index greater than 1 for non-carcinogenic risks. If post-
occupancy indoor air sampling is deemed to be warranted, DEQ will be notified to discuss the
sampling locations and analyte list, and written approval will be obtained prior to proceeding with
the sampling.

Tables

Table 1
Summary of Indoor Air Analytical Results (Area C & D)
Battery & Ignition Distribution
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
Brownfields Project No. 23055-19-060
H&H Job No. PDP-001
Building Area
Sample Location Area D Unit #133 Outdoor Ambient Air
Sample ID D-IAS-1 IAS-BKG
Date Collected
VOCs (TO-15)
Acetone 118 114 263 9.14 B NE
Benzene 2.22 2.29 1.20 J 0.897 0.36
Chloromethane 0.947 J 0.949 J 0.972 J <0.067 19
Dichlorodifluoromethane 2.87 2.89 2.83 2.83 21
Ethylbenzene 3.23 3.20 1.81 J <0.106 1.1
4-Ethyltoluene 1.88 J 1.93 J 0.958 J <0.128 NE
1,1,2-Trichloro-1,2,2-trifluoroethane 0.590 J 0.582 J 0.590 J 0.597 J 1,000
Heptane 2.17 2.41 1.31 J 0.672 J 83
n-Hexane 2.51 2.58 1.32 J 0.676 J 150
Isopropyl Alcohol 6.34 B 6.33 B 9.13 B 2.88 J, B 42
Methyl Ethyl Ketone (MEK) 65.0 65.8 59.3 3.49 1,000
Methylene Chloride 1.08 J 1.63 J 1.47 J 1.28 J 100
Naphthalene 0.571 J 0.560 J <0.183 <0.183 0.083
Styrene 2.11 J 2.14 1.63 J <0.124 210
Tetrachloroethene <0.181 <0.181 <0.181 <0.181 8.3
Tetrahydrofuran 25.0 25.6 23.8 1.66 420
Toluene 9.65 11.4 6.48 3.52 1,000
Trichloroethene <0.199 <0.199 <0.199 <0.199 0.42
Trichlorofluoromethane 1.65 J 1.74 J 1.58 J 1.62 J NE
1,2,4-Trimethylbenzene 10.3 10.2 4.74 <0.110 13
1,3,5-Trimethylbenzene 2.69 2.77 1.23 J <0.236 13
o-Xylene 11.1 11.4 6.24 0.408 J 21
mp-Xylene 12.4 12.5 6.63 0.864 J 21
Xylene (Total)23.5 23.9 12.9 1.27 J 21
DEQ Cumulative Risk Calculator (2)Acceptable Risk Levels (3)
LICR (Worst-Case Residential)--≤1.0 x 10-4
HI (Worst-Case Residential)--≤1.0
Notes:
1) North Carolina Department of Environmental Quality (DEQ) Vapor Intrusion Indoor Air Screening Levels (IASLs) dated February 2024.
2) Risks calculated using DEQ Risk Calculator (dated February 2024) and the highest concentration of any compound detected in the samples.
3) Cumulative LICR and HI are compared to the DEQ and Environmental Protection Agency (EPA) acceptable levels for carcinogenic and non-carcinogenic risks.
Only constituents detected in at least one sample and select chlorinated compounds are shown in the table above.
Compound concentrations and IASLs are reported in micrograms per cubic meter (µg/m3).
Compound concentrations are reported to the laboratory method detection limits.
Laboratory analytical method is shown in parentheses.
Bold values exceed the Residential IASL.
LICR = Lifetime Incremental Cancer Risk; HI = Hazard Index
VOCs = volatile organic compounds; -- = not applicable; NE = not established
J = Estimated concentration between laboratory reporting limit and method detection limit.
B = Compound was detected in laboratory method blank.
1.6 X 10-5
0.82
2/20/24 to 2/21/24
Area C & D
Residential IASLs (1)Area C Unit #148
C-IAS-1 / IAS-DUP
https://harthick.sharepoint.com/sites/MasterFiles-1/Shared Documents/AAA-Master Projects/Proffitt Dixon - PDP/PDP-001 - Tryclan Avenue/VIMS install report/Areas C and D/Tables/Area C&D Data Tables
3/26/2024
Table 1 (Page 1 of 1)
Hart & Hickman, PC
Table 2
Summary of Sub-Slab Soil Gas Analytical Results (Area C & D)
Battery & Ignition Distribution
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
Brownfields Project No. 23055-19-060
H&H Job No. PDP-001
Building Area
Sample ID MP-3
Date Collected
VOCs (TO-15)
Acetone 17,400 66.0 67.4 NE
Benzene <1.46 2.47 2.44 12
Carbon Disulfide <1.22 0.747 J 0.737 J 4,900
Chloroform <1.73 0.522 J 0.517 J 4.1
Cyclohexane 28.7 J <0.161 <0.161 42,000
Dichlorodifluoromethane <2.68 2.84 2.90 700
Ethylbenzene <2.12 1.44 J 1.44 J 37
4-Ethyltoluene <2.56 0.408 J 0.408 J NE
1,1,2-Trichloro-1,2,2-trifluoroethane <11.2 0.597 J 0.643 J 35,000
Heptane <2.86 0.401 J 0.368 J 2,800
n-Hexane <0.942 1.42 J 1.11 J 4,900
Isopropyl Alcohol 55.1 J 3.83 J, B 3.52 J, B 1,400
Methyl Ethyl Ketone (MEK)<4.48 76.2 79.0 35,000
Methylene Chloride 12.4 J 3.94 1.55 J 3,400
Naphthalene <3.66 0.492 J 0.560 J 2.8
Propene <4.84 4.59 4.59 21,000
Styrene <2.48 0.379 J 0.379 J 7,000
Tetrachloroethene <3.62 <0.181 <0.181 280
Tetrahydrofuran 14,200 63.9 63.7 14,000
Toluene <1.80 3.34 3.32 35,000
Trichloroethene <3.98 <0.199 <0.199 14
Trichlorofluoromethane <2.60 1.80 J 1.74 J NE
1,2,4-Trimethylbenzene <2.20 1.85 J 1.82 J 420
1,3,5-Trimethylbenzene <4.72 0.565 J 0.535 J 420
o-Xylene <3.14 2.73 2.62 700
m,p-Xylene 7.47 J 5.53 J 5.47 J 700
Xylene (Total) 7.47 J 8.26 J 8.09 J 700
DEQ Cumulative Risk Calculator (2)Acceptable Risk Levels (3)
LICR (Worst-Case Residential)≤1.0 x 10-4
HI (Worst-Case Residential)≤1.0
Notes:
1) North Carolina Department of Environment Quality (DEQ) Residential Sub-Slab and Exterior Soil Gas Screening Levels (SGSLs) dated February 2024.
2) Risks calculated using DEQ Risk Calculator (dated February 2024) and the highest concentration of any compound detected in the samples
3) Cumulative LICR and HI are compared to the DEQ and Environmental Protection Agency (EPA) acceptable levels for carcinogenic and non-carcinogenic risks.
Only constituents detected in at least one sample and select chlorinated compounds are shown in the table above.
Compound concentrations and SGSLs are reported in micrograms per cubic meter (µg/m3).
Compound concentrations are reported to the laboratory method detection limits.
Laboratory analytical method is shown in parentheses.
Bold values exceed the Residential SGSL.
LICR = Lifetime Incremental Cancer Risk; HI = Hazard Index
VOCs = volatile organic compounds; NE = not established
J = Estimated concentration between laboratory reporting limit and method detection limit.
B = Compound was detected in laboratory method blank.
Residential SGSLs (1)
Area C & D
0.23
5.8 X 10-7
MP-5 / MP-DUP
2/21/2024
https://harthick.sharepoint.com/sites/MasterFiles-1/Shared Documents/AAA-Master Projects/Proffitt Dixon - PDP/PDP-001 - Tryclan Avenue/VIMS install report/Areas C and D/Tables/Area C&D Data Tables
3/26/2024
Table 2 (Page 1 of 1)
Hart & Hickman, PC

Figures

REVISION NO. 0
JOB NO. PDP-001
DATE: 6-15-23
FIGURE NO. 2
BATTERY & IGNITION DISTRIBUTION
TRYCLAN DRIVE AND ELLENWOOD PLACE
CHARLOTTE, NORTH CAROLINA
SITE MAP
LEGEND
BROWNFIELDS PROPERTY BOUNDARY
PARCEL BOUNDARY
2923 South Tryon Street-Suite 100
Charlotte, North Carolina 28203
704-586-0007(p) 704-586-0373(f)
License # C-1269 / #C-245 Geology
DEUTSCHE PROCESS
(3642 & 3630 TRYCLAN DRIVE)
RESIDENCE
(3701 ELLENWOOD PLACE)
RESIDENCE
(3709 ELLENWOOD PLACE)
RESIDENCE
(3715 ELLENWOOD PLACE)
RESIDENCE
(3706 ELLENWOOD PLACE)
RESIDENCE
(3712 ELLENWOOD PLACE)
ELL
E
N
W
O
O
D

P
L
A
C
E
S. T
R
Y
O
N

S
T
R
E
E
T
TRYC
L
A
N

D
R
I
V
E
DE
W
I
T
T

L
A
N
E
GILDE BREWERY
(3530 DEWITT LANE)
BSR MODERN MARTIAL ARTS
(3539-3543 DEWITT LANE)
MAA LOSO
(4107-4115 CRAFT STREET)
RESIDENTIAL
DEW
I
T
T

L
A
N
E
YORKSHIRE DRIVE
BROWNFIELDS PROPERTY
(BPN 22033-18-60)
GLE
A
S
O
N

W
A
Y
YORK
S
H
I
R
E

D
R
I
V
E
NOTES:
1.AERIAL IMAGERY AND PARCEL DATA OBTAINED FROM
MECKLENBURG COUNTY GIS (2022).
2.BPN = BROWNFIELDS PROJECT NUMBER
MAKE A MOVE / BEKINS
(3520 DEWITT LANE)
PARKING
DECK
S:\
A
A
A
-
M
a
s
t
e
r

P
r
o
j
e
c
t
s
\
P
r
o
f
f
i
t
t

D
i
x
o
n

-

P
D
P
\
P
D
P
-
0
0
1

-

T
r
y
c
l
a
n

A
v
e
n
u
e
\
M
W

A
b
a
n
d
o
n
m
e
n
t
\
S
i
t
e

M
a
p
.
d
w
g
,

F
I
G

2
,

6
/
1
5
/
2
0
2
3

3
:
4
5
:
5
6

P
M
,

k
m
c
k
i
n
n
e
y

Appendix A

Site Development Phasing Plan

9$1 9$1
9$
1
(9
&(9
&
&
(9
(9
9$1
FDFD
FD
FD
FD
FD
FD
FD
FD
DN
DNDN DN
FD
FD
FD
FD
83 '1
'1 83







UP












DN
UP

DN






GARAGE VENTILATION SHAFT




DN


THE FRONT PORCH

DN
DN
GARAGE VENTILATION SHAFT







%8,/',1*
3+$6(
%8,/',1*3$57,
3+$6(
%8,/',1*
3+$6(
%8,/',1*3$57,,
3+$6(
3-HR FIREWALL
3-HR FIREWALL
3-HR FIREWALL
%8,/',1*3$57,
3+$6(
%8,/',1*3$57,,
3+$6(
3-HR FIREWALL PROVIDED FOR
PHASING ONLY. FIREWALL DOES NOT
CREATE A NEW FIRE AREA OR
CONSTITUTE A HORIZONTAL EXIT
3-HR FIREWALL PROVIDED FOR
PHASING ONLY. FIREWALL DOES NOT
CREATE A NEW FIRE AREA OR
CONSTITUTE A HORIZONTAL EXIT.
50'-0'' MAX.
50'-0'' MAX.
TEMP. CONST. BARRIER TO PREVENT
DEAD END CONDITION UNTIL PHASE 2
IS COMPLETE.
%/'*&216758&7,213+$6,1*1$55$7,9(
MECHANICAL
1. PRIOR TO RECEIVING TCO PER FLOOR, ALL OPENINGS FOR AIR SHAFTS SHALL HAVE FIRE / SMOKE
DAMPERS IN PLACE ON OTHER FLOORS.
PLUMBING
1. CONSTRUCTION SHALL BE PHASED SUCH THAT THE INITIAL PHASE INCLUDES ALL PLUMBING PIPING
INSTALLED UP TO BUT NOT INCLUDING FIXTURES. THE ONLY FIXTURE TO BE INSTALLED SHALL BE THE
TUBS WITH CAPPED CW AND HW IN PREPARATION FOR TRIM INSTALLATION.
ELECTRICAL
1. WHEN ENERGIZING A FLOOR FOR TURN OVER, ALL BRANCH CIRCUITS SERVING OTHER AREAS FROM
THE SAME PANEL SHALL BE TAGGED/LOCKED OUT AT THE PANEL.
2. ALL NORMAL/EGRESS LIGHTING AND SIGNAGE SHALL BE INSTALLED AND OPERATIONAL FROM THE
AREA BEING OCCUPIED DOWN TO THE BUILDING EXIT.
3. FIRE ALARM SYSTEM SHALL BE WIRED AND PROGRAMMED TO ALLOW EACH FLOOR AND EACH PHASE
TO BE OCCUPIED SEPARATELY.
LIFE SAFETY
1. ELEVATORS WILL BE OPERATIONAL. ELEVATORS WILL BE AVAILABLE TO CONSTRUCTION TRAFFIC
UNTIL THE ADJACENT BUILDING PHASE (APARTMENTS) IS COMPLETED. AT THAT TIME, USE OF
ELEVATORS WILL BE FOR RESIDENT TRAFFIC ONLY.
2. STAIRWELLS TO BE COMPLETE AND USABLE BY TENANTS. CONTRACTOR TO MAINTAIN STAIRWELLS
TO MAKE SURE THERE IS NO CONSTRUCTION DEBRIS AND THAT A CONTINUOUS PATH OF EGRESS IS
PROVIDED AT ALL TIMES. SIGNAGE WILL BE PROVIDED AT EACH FLOOR LEVEL UNDER CONSTRUCTION
RESTRICTING ACCESS TO AUTHORIZED CONSTRUCTION PERSONNEL ONLY.
3. AN UNOBSTRUCTED PATH OF EGRESS MUST BE MAINTAINED FROM EACH POINT OF EXIT FROM THE
BUILDING OUT TO THE PUBLIC WAY.
4. TEMPORARY CONSTRUCTION BARRIERS SHALL BE PLACED AS SHOWN ON THE PHASING PLANS TO
PREVENT TENANT ACCESS TO AREAS THAT HAVE NOT RECEIVED TCO'S AND/OR PREVENT DEAD END
CORRIDOR CONDITIONS LONGER THAN 50'-0" FROM A POINT OF DECISION.
CONSTRUCTION OF THIS BUILDING TO BE PHASED. OVERALL BUILDING WILL BE COMPLETED IN 4
SEPARATE PHASES, SEPARATED BY FIRE WALLS. BUILDINGS WILL BE COMPLETED FROM THE BOTTOM UP
WITH BOTTOM FLOOR RECEIVING TCO'S FIRST AND FLOORS ABOVE FOLLOWING SEQUENTIALLY. PARKING
GARAGE IS PERMITTED SEPARATELY AND WILL BE FULLY COMPLETE AT THE END OF PHASE 1 TCO TO
ALLOW FOR RESIDENT PARKING. POOL & COURTYARD WILL ALSO HAVE A SEPARATE PERMIT.. MINIMUM
LIFE SAFETY MUST BE IN PLACE AND OPERATIONAL THROUGHOUT THE BUILDING BEFORE TCO'S WILL BE
APPROVED. THE FOLLOWING IS A NARRATIVE TO ADDRESS CONSTRUCTION PHASING:
FIRE/SPRINKLER
1. FIRE ALARM WILL BE OPERATIONAL THROUGHOUT THE BUILDING AT THE TIME OF PARKING
GARAGE/PHASE 1 TCO.
2. SPRINKLER SYSTEM WILL BE OPERATIONAL THROUGHOUT THE BUILDING AT THE TIME OF PARKING
GARAGE/PHASE 1 TCO.
%/'*&216758&7,213+$6,1*3/$1.(<
PHASE 1
(BUILDING 1 - PARKING GARAGE):
TYPE 1A
• INCLUDES ALL LEVELS OF PARKING GARAGE (TYPE 1A)
(BLDG 2 PART I- RESIDENTIAL BUILDING)
TYPE 3A
• INCLUDES LEASING OFFICE
• INCLUDES RESIDENTIAL FLOORS (LEVEL 1-5 W/96 UNITS) WHICH WILL BE
PERMITTED BY FLOOR AND RECEIVE TCO'S FROM BOTTOM UP.
• BASEMENT LEVEL OF RESIDENTIAL BUILDING
PHASE 3
(BLDG 3 - RESIDENTIAL BUILDING):
TYPE 3A
• INCLUDES RESIDENTIAL FLOORS (LEVEL 1-5 W/110 UNITS) WHICH WILL BE
PERMITTED BY FLOOR AND RECEIVE TCO'S FROM BOTTOM UP.
PHASE 5
(BLDG 4 PART II - RESIDENTIAL BUILDING)
TYPE 3A
• INCLUDES RESIDENTIAL FLOORS (LEVEL 1-5 W/45 UNITS) WHICH WILL BE
PERMITTED BY FLOOR AND RECEIVE TCO'S FROM BOTTOM UP.
PHASE 4
(BLDG 4 PART I - RESIDENTIAL BUILDING)
TYPE 3A
• INCLUDES RESIDENTIAL FLOORS (LEVEL 1-5 W/59 UNITS) WHICH WILL BE
PERMITTED BY FLOOR AND RECEIVE TCO'S FROM BOTTOM UP.
PHASE 2
(BLDG 2 PART II - RESIDENTIAL BUILDING):
TYPE 3A
• INCLUDES RESIDENTIAL FLOORS (LEVEL 1-5 W/33 UNITS) WHICH WILL BE
PERMITTED BY FLOOR AND RECEIVE TCO'S FROM BOTTOM UP.
• INCLUDES CLUBHOUSE, FITNESS AREAS, 5TH FLOOR AMENITY A
333 WEST TRADE STREET
R C H I T E C T U R E
SUITE 200CHARLOTTE, NC 28202
T 704.927.9900
w w w. a x i o m a r c h i t e c t u r e . c o m
REVISIONS
PROJECT A-2011
DECEMBER 9, 2021
A0.12
LEVEL 1 PHASING
PLAN
75
<
&
/
$
1

'
5
,
9
(

$
1
'

'
H
:
,
7
7

/
$
1
(
&+
$
5
/
2
7
7
(


1
2
5
7
+

&
$
5
2
/
,
1
$
Lo
S
o

V
I
L
L
A
G
E

A
P
A
R
T
M
E
N
T
S
35
2
)
)
,
7
7
',
;
2
1

3
$
5
7
1
(
5
6
ISSUED FOR CONSTRUCTION
12/9/2021
1/16" = 1'-0"A0.12
1 /(9(/3+$6,1*)/2253/$1
12/9/2021
A1 - Parking Garage
A2
PARKING
GARAGE
C
B
D
A2
B
C
D

Appendix B

VIMS As-Built Drawings (VM-1, VM-2, VM-3, and VM-4)

A
333 WEST TRADE STREET
R C H I T E C T U R E
SUITE 200CHARLOTTE, NC 28202
T 704.927.9900
w w w. a x i o m a r c h i t e c t u r e . c o m
REVISIONS
VM-1
TR
Y
C
L
A
N

D
R
I
V
E

A
N
D

D
e
W
I
T
T

L
A
N
E
CH
A
R
L
O
T
T
E
,

N
O
R
T
H

C
A
R
O
L
I
N
A
PR
O
F
F
I
T
T
-
D
I
X
O
N

P
A
R
T
N
E
R
S
VAPOR INTRUSION MITIGATION SYSTEM (VIMS) SPECIFICATIONS
1.THIS VAPOR INTRUSION MITIGATION PLAN WAS USED FOR DIRECTION OF VIMS COMPONENT INSTALLATION ONLY AND WAS NOT USED TO GUIDE CONSTRUCTION OF STRUCTURAL COMPONENTS NOT RELATED TO
THE VIMS. CONSTRUCTION CONTRACTOR WAS RESPONSIBLE FOR VERIFYING CONSISTENCY OF VIMS DETAILS WITH APPLICABLE STRUCTURAL, ARCHITECTURAL, MECHANICAL, AND PLUMBING PLANS AND
RESOLVED INCONSISTENCIES WITH THE DESIGN ENGINEER PRIOR TO VIMS INSTALLATION. THE CONSTRUCTION CONTRACTOR WAS RESPONSIBLE FOR INSTALLING THE VIMS IN ACCORDANCE WITH APPLICABLE
BUILDING CODES.
2.CONSTRUCTION CONTRACTORS AND SUB-CONTRACTORS USED "LOW OR NO VOC" PRODUCTS AND MATERIALS, WHEN POSSIBLE. BASED ON INFORMATION PROVIDED BY THE CONTRACTORS, NO PRODUCTS
CONTAINING TETRACHLOROETHENE OR TRICHLOROETHENE WERE USED.
3.VIMS VAPOR LINER IS VAPORBLOCK PLUS 20 VAPOR BARRIER MANUFACTURED BY VIAFLEX.
THE VAPOR LINER WAS INSTALLED AS SPECIFIED HEREIN AND PER MANUFACTURER INSTALLATION INSTRUCTIONS TO CREATE A CONTINUOUS LINER BELOW GROUND FLOOR SLABS. A BASE COURSE CONSISTING
OF CLEAN #57 (OR SIMILAR HIGH PERMEABILITY STONE APPROVED BY THE ENGINEER) WAS INSTALLED BENEATH THE VIMS VAPOR LINER. IN AREAS AROUND THE SUB-SLAB PIPING AND SOIL GAS COLLECTOR MAT,
THE BASE COURSE LAYER IS THICK ENOUGH TO COVER THE SUB-SLAB PIPING AND SOIL GAS COLLECTOR MAT WITH A MINIMUM 1-INCH LAYER BELOW THE PIPING AND MAT. IN AREAS WITHOUT PIPING OR SOIL GAS
COLLECTOR MAT, THE BASE COURSE IS A MINIMUM OF 3-INCHES THICK.
4.ALL PENETRATIONS WERE SEALED ACCORDING TO VAPOR LINER MANUFACTURER INSTALLATION INSTRUCTIONS AS FOUND IN THE MANUFACTURER INSTALLATION GUIDELINES. SMALL PUNCTURE HOLES WERE
SEALED WITH THE VAPORSEAL™TAPE, BUTYL SEAL DOUBLE SIDED TAPE, OR POUR-N-SEAL™AND LARGER HOLES, TEARS, OR DAMAGE WERE REPAIRED USING A PATCH THAT OVERLAPS THE DAMAGED AREA AND
THEN TAPED ALONG THE SEAMS. IN AREAS WHERE UTILITY PENETRATIONS (I.E. PIPING, DUCTS, ETC) ARE PRESENT AND THE USE OF TAPING WAS NOT PRACTICAL OR DEEMED AS "INEFFECTIVE" BY THE DESIGN
ENGINEER, POUR-N-SEAL WAS POURED INTO FORM TO PATCH THE PENETRATION WITH AN AIRTIGHT SEAL. POUR-N-SEAL™ WAS USED AT ELECTRICAL CONDUIT BANKS ONLY.
5.CONSTRUCTION CONTRACTORS AND SUB-CONTRACTORS AVOIDED THE USE OF TEMPORARY FORM BOARDS THAT PENETRATE THE VAPOR LINER WHERE POSSIBLE. WHERE TEMPORARY FORM BOARDS WERE
USED, THE SIZE AND NUMBER OF PENETRATIONS THROUGH THE VAPOR LINER WERE LIMITED AND SMALL DIAMETER STAKES (I.E. SOLID METAL STAKES) WERE USED. IN ALL CASES, AS FORM BOARDS WERE
REMOVED, THE CONTRACTOR OR SUB-CONTRACTORS SEALED ALL PENETRATIONS IN ACCORDANCE WITH VAPOR LINER MANUFACTURER INSTALLATION INSTRUCTIONS. NO HOLLOW PIPING WAS USED.
6.VIMS BELOW AND ABOVE GRADE PIPING IS NOT TRAPPED AND IS SLOPED A MINIMUM OF 18 UNIT VERTICAL IN 12 UNITS HORIZONTAL (1% SLOPE) TO GRAVITY DRAIN. SOLID SECTIONS OF HORIZONTAL COLLECTION
PIPE WERE SUPPORTED TO PREVENT PIPE SAG OR LOW POINT AND MAINTAIN 1% SLOPE TOWARD SLOTTED SECTIONS TO DRAIN CONDENSATION. HORIZONTAL COLLECTION PIPE CONSISTS OF BOTH THREADED
FLUSH JOINT OR GLUE JOINT 3" SCH 40 PVC PIPE WITH 0.020" TO 0.060" SLOT WIDTH AND 1
8" SLOT SPACING AND SOIL GAS COLLECTOR MAT (1" x 12") WITH 3" SCH 40 PVC AT SUB-GRADE FOUNDATION. FOAM PIPE
SLEEVES, OR SIMILAR, WERE INSTALLED AROUND HORIZONTAL PORTIONS OF PIPES THAT PENETRATE CONCRETE FOOTERS AND WALLS PER APPLICABLE STRUCTURAL PLANS AND BUILDING CODES, OR AS
OTHERWISE DIRECTED BY THE APPLICABLE PLANS AND CONSTRUCTION ENGINEERS. PIPE SLEEVES WERE SEALED TO PREVENT A PREFERENTIAL AIR PATHWAY FROM BELOW THE SLAB INTO THE BUILDING. PLEASE
REFER TO SHEET S3.03 IN THE STRUCTURAL DRAWINGS FOR FOOTING DETAILS ADDRESSING VIMS PIPING.
7.3" SCH 40 PVC RISER DUCT PIPING WAS INSTALLED TO CONNECT EACH SLAB PENETRATION LOCATION TO A ROOFTOP EXHAUST DISCHARGE POINT WITH A SYPHON VENTILATOR (SEE DETAIL #15). ABOVE-SLAB
RISER DUCT PIPE RUNS BETWEEN THE SLAB PENETRATION AND THE ROOFTOP EXHAUST DISCHARGE WERE INSTALLED PER APPLICABLE NORTH CAROLINA PLUMBING AND BUILDING CODES AND AS SPECIFIED IN
THE CONSTRUCTION DOCUMENTS AND DRAWINGS.
8.RISER DUCT PIPING EXTENDS IN A VERTICAL ORIENTATION THROUGH THE BUILDING ROOF AND TERMINATES A MINIMUM OF 2 FT ABOVE THE BUILDING ROOF LINE. AN EMPIRE MODEL STAINLESS STEEL SYPHON
VENTILATOR WAS INSTALLED ON THE EXHAUST DISCHARGE END OF EACH RISER DUCT PIPE. AN ADAPTOR COUPLING WAS INSTALLED AT THE DISCHARGE END OF THE 3" RISER DUCT PIPE AND THE VENTILATOR
WAS SECURED TO THE PVC RISER IN A VERTICAL ORIENTATION. EXHAUST DISCHARGE LOCATIONS ARE A MINIMUM OF 10 FT FROM ANY OPERABLE OPENING OR AIR INTAKE INTO THE BUILDING. NOTE THAT SOME
DISCHARGE LOCATIONS ON THE ROOFTOP DEPICTED IN THE VAPOR INTRUSION MITIGATION PLAN WERE REPOSITIONED AND THE NEW POSITIONS MEET THE REQUIREMENTS PRESENTED ABOVE. AN ELECTRICAL
JUNCTION BOX (120V, 60Hz AC REQUIRED) WAS INSTALLED NEAR THE FAN LOCATION ON THE ROOFTOP FOR CONVERSION TO ELECTRIC FANS, IF REQUIRED. ALL WIRING AND ELECTRICAL WAS INSTALLED PER
APPLICABLE BUILDING AND ELECTRICAL CODES. VIMS ROOF VENTILATORS WERE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S WRITTEN INSTRUCTIONS.
9.ABOVE-SLAB ACCESSIBLE RISER DUCT PIPING IS PERMANENTLY IDENTIFIED BY MEANS OF A TAG OR STENCIL AT A MINIMUM OF ONCE EVERY 10-LINEAR FT WITH "VAPOR MITIGATION - CONTACT MAINTENANCE". THE
SYPHON VENTILATORS ARE LABELED WITH "VAPOR MITIGATION SYSTEM - CONTACT MAINTENANCE".
10.INSPECTIONS OF EACH COMPONENT OF THE VIMS WAS CONDUCTED BY THE ENGINEER, OR ENGINEER'S DESIGNEE, TO CONFIRM VIMS COMPONENTS WERE INSTALLED PER THE APPROVED DESIGN. THE
INSPECTIONS INCLUDED: (1) INSPECTION OF SUB-SLAB PIPING LAYOUT AND GRAVEL PLACEMENT PRIOR TO INSTALLING VAPOR LINER; (2) INSPECTION OF VAPOR LINER PRIOR TO POURING CONCRETE; (3)
INSPECTION OF ABOVE-GRADE PIPING LAYOUT; AND (4) INSPECTION OF FAN AND VENT PIPE CONNECTIONS. THE CONSTRUCTION CONTRACTOR(S) COORDINATED WITH THE ENGINEER TO PERFORM THE REQUIRED
INSPECTIONS. NO VIMS COMPONENTS WERE COVERED WITHOUT BEING INSPECTED.
PDP-001
VAPOR
MITIGATION PLAN
SPECIFICATIONS
AS-BUILTS
ISSUED FOR CONSTRUCTION
VAPOR MITIGATION PLAN
PREPARED BY:
2923 South Tryon Street-Suite 100
Charlotte, North Carolina 28203
704-586-0007(p) 704-586-0373(f)
License # C-1269 / #C-245 Geology
EL
L
O

A
P
A
R
T
M
E
N
T
S
FEBRUARY 6, 2024
S:\
A
A
A
-
M
a
s
t
e
r

P
r
o
j
e
c
t
s
\
P
r
o
f
f
i
t
t

D
i
x
o
n

-

P
D
P
\
P
D
P
-
0
0
1

-

T
r
y
c
l
a
n

A
v
e
n
u
e
\
V
I
M
S

i
n
s
t
a
l
l

r
e
p
o
r
t
\
F
i
g
u
r
e
s
\
V
M
P

A
s
-
B
u
i
l
t
s
_
2
.
6
.
2
4
.
d
w
g
,

v
m
-
1

s
p
e
c
s
,

S
V
i
n
c
e
n
t
VIMS VAPOR LINER AND BASE COURSE (TYP)1
BASE COURSE - CLEAN #57 STONE
MIN 3" THICK BENEATH VIMS VAPOR LINER
VAPOR LINER (SEE SPECIFICATION #3)
CONCRETE FLOOR SLAB
NTSVM2
SUBBASE
SECTION THROUGH EXTERIOR WALL
NTSVM2
BRICK OR BUILDING SIDING
EXTERNAL WALL (NOT
PRESENT AT ALL LOCATIONS)
STUD WALL BASE COARSE
(SEE SPECIFICATION #3)
VAPOR LINER SEALED TO CONCRETE PER
MANUFACTURER INSTRUCTIONS.
SUBBASE
3
VAPOR LINER EXTENDS ALONG
FOOTING EXTERIOR WHERE POSSIBLE
AT LOCATIONS WHERE EXTERIOR
GRADE IS HIGHER THAN INTERIOR
GRADE
4A
NTSVM2
2" SCH 40 PVC 90 DEGREE ELBOW
VAPOR LINER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
2" VENT SCREEN AT
END OF PIPE
EXTERNAL/STUD WALL
(NOT PRESENT IN ALL
LOCATIONS)
2" SOLID SCH 40 PVC
VACUUM MEASURING POINT
VACUUM MONITORING POINT IS
POSITIONED SO VENT SCREEN
IS AT LEAST 5 FT FROM AN
EXTERNAL WALL
2' MIN
EXTERNAL/STUD WALL
(NOT PRESENT IN ALL
LOCATIONS)
FLOOR CLEANOUT, ADJUSTABLE,
4" DIA ZURN INDUSTRIES
MODEL #CO2450-PV4FLUSH WITH
FINISHED FLOOR
4B
NTSVM2
2" SCH 40 PVC 90 DEGREE ELBOW
VAPOR LINER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
2" VENT SCREEN AT
END OF PIPE
STUD WALL
(NOT PRESENT IN ALL
LOCATIONS)
VACUUM MEASURING POINT THROUGH THICKENED SLAB
FLOOR CLEANOUT, ADJUSTABLE,
4" DIA ZURN INDUSTRIES
MODEL #CO2450-PV4
FLUSH WITH
FINISHED FLOOR
2" SOLID SCH 40 PVC
- PIPE SLEEVES
INCLUDED WHEN
APPLICABLE; SEE
SPECIFICATION #6
VAPOR LINER PENETRATION SEALED
TO PIPE PER MANUFACTURER
INSTRUCTIONS
STUD WALL
(NOT PRESENT IN ALL LOCATIONS)
VAPOR LINER
BENEATH
THICKENED SLAB
HORIZONTAL PIPE THROUGH THICKENED SLAB
TOP OF THICKENED
SLAB TURNDOWN
FIRE WALL (NOT PRESENT
IN ALL LOCATIONS)
3" SOLID SCH 40 PVC -
INCLUDE PIPE SLEEVES
WHEN APPLICABLE; SEE
SPECIFICATION #6
6
VM2 NTS
SLOTTED 3" SCH
40 PVC
SOLID TO SLOTTED
3" SCH 40 PVC PIPE
TRANSITION (SLIP
COUPLING OR
THREADED JOINT)
VIMS VACUUM MEASURING POINT - DETAIL VIEW
NTSVM2
5
FINISHED FLOOR SLAB
2" SCH 40 PVC SET WITHIN GRAVEL LAYER
(SEE DETAILS 4A & 4B)
2" DRAIN EXPANSION TEST PLUG
BASE COURSE
(SEE SPECIFICATION #3)
FLOOR CLEANOUT, ADJUSTABLE, 4" DIA ZURN
INDUSTRIES MODEL #CO2450-PV4 FLUSH
WITH FINISHED FLOOR
4" x 2" FLUSH REDUCER
BUSHING
VAPOR BARRIER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
2" SCH 40 PVC 90 DEGREE STREET ELBOW
VERTICAL RISER AT SLAB PENETRATION WITH 90 DEGREE ELBOW
NTS
VAPOR LINER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
3" SCH 40 PVC 90 DEGREE ELBOW
STUD WALL
3" SCH 40 PVC RISER DUCT PIPE
(SEE SPECIFICATION #8 & #9)
BASE COARSE
(SEE SPECIFICATION #3)
THICKENED SLAB MAY NOT BE PRESENT IN
ALL LOCATIONS
3" SOLID SCH 40 PVC
(SEE SPECIFICATION #6)
VM2
8A
SOIL GAS COLLECTOR MAT
TO SOLID 3" SCH 40 PVC
CONNECTION
VERTICAL RISER AT SLAB PENETRATION WITH TEE
NTS
VAPOR LINER
PENETRATION SEALED TO
PIPE PER MANUFACTURER
INSTRUCTIONS
3" TO 4" SCH 40 PVC 90 DEGREE TEE
STUD WALL
3" SCH 40 PVC RISER DUCT PIPE
(SEE SPECIFICATION #8 & #9)
THICKENED SLAB MAY NOT BE PRESENT IN ALL
LOCATIONS
3" SOLID SCH 40 PVC
(SEE SPECIFICATION #6)
10
VM2
SOLID TO SLOTTED 3" SCH 40
PVC PIPE TRANSITION (SLIP COUPLING
OR THREADED JOINT)
BASE COURSE
BASE COURSE
(SEE SPECIFICATION #3)
VAPOR BARRIER SEALED TO CONCRETE
PER MANUFACTURER INSTRUCTIONS
VAPOR LINER SEALED TO COLUMN PER
MANUFACTURER INSTRUCTIONS
TYPICAL VIMS LINER ABOVE COLUMN FOOTING11
NTSVM2
TYPICAL VIMS LINER AT ELEVATOR PIT12
NTSVM2
ELEVATOR
PARKING
GARAGE
(BASEMENT)
STAIRWELL
PARKING
GARAGE
(BASEMENT)
VAPOR LINER
SUB-BASE
VAPOR LINER SEALED
TO WATERPROOFING
VAPOR LINER
VIMS SYPHON VENTILATOR & EXHAUST (TYP)15
VM2 NTS
ELECTRICAL JUNCTION BOX FOR POTENTIAL
FUTURE VACUUM FAN (REFER TO
SPECIFICATION #8)
RISER DUCT PIPE THROUGH ROOF
FLASHING
ROOFTOP
4" X3" HEAVY
DUTY NO HUB
COUPLING
4" SYPHON VENTILATOR (EMPIRE SYPHON
VENTILATOR OR ENGINEER APPROVED
EQUIVALENT)
GROUND FLOOR
INTERIOR SPACE
BASEMENT LEVEL
HALLWAY
SUB-BASE
CONCRETE
FLOOR SLAB
BASE COURSE
(SEE SPECIFICATION #3)
VAPOR LINER
(SEE SPECIFICATION #3)
VAPOR LINER SEALED TO OUTSIDE OF CONCRETE
AND WATERPROOFING/INSULATION (WHERE
PRESENT) PER MANUFACTURER INSTRUCTIONS
WATERPROOFING AND
RIGID INSULATION
DRAIN
STUD/SHEAR
WALL
VIMS AT RETAINING WALL13
NTSVM2
THICKENED SLAB TRANSITION7
NTSVM2
BASE COARSE
(SEE SPECIFICATION #3)
FIRE WALL PRESENT IN
SOME AREAS
STUD WALL
VAPOR LINER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
3" SCH 40 PVC 45 DEGREE ELBOW
SLAB STEP HEIGHT VARIES
3" SOLID SCH 40 PVC
(SEE SPECIFICATION #6)
SOLID TO SLOTTED 3" SCH 40 PVC
PIPE TRANSITION (SLIP COUPLING
OR THREADED JOINT)
SOLID TO SLOTTED 3" SCH 40 PVC
PIPE TRANSITION (SLIP COUPLING
OR THREADED JOINT)
VIMS PIPING THROUGH SLAB DROP WITH RISER DUCT PIPING (TYP)
NTS
9
VM2
SUB-BASE
VAPOR LINER
BASE COURSE
(SEE SPECIFICATION #3)
SOLID TO SLOTTED 3" SCH 40 PVC
PIPE TRANSITION (SLIP COUPLING
OR THREADED JOINT)
3" SCH 40 PVC
90-DEGREE ELBOW
VAPOR LINER SEALED TO PIPE
PER MANUFACTURER
INSTRUCTIONS
SOLID 3" SCH 40 PVC
(SEE SPECIFICATION #7)STUD WALLS
SOLID 3" SCH 40 PVC
RISER DUCT PIPE
(SEE SPECIFICATION #2)
3" SCH 40 PVC
90-DEGREE TEE
SECTION THROUGH SLAB EDGE AT PARKING GARAGE
NTSVM2
STUD WALL BASE COARSE
(SEE SPECIFICATION #3)
VAPOR LINER SEALED TO CONCRETE PER
MANUFACTURER INSTRUCTIONS.
SUBBASE
14
VAPOR LINER SHALL EXTEND ALONG
FOOTING EXTERIOR TO SLAB GRADE
CONDITION VARIES
AT PARKING GARAGE
SUB-BASE
SLOTTED COLLECTION PIPE (TYP)2
NTSVM-2
PVC TERMINATION SCREEN
CONCRETE FLOOR SLAB
VAPOR BARRIER
(SPECIFICATION #3)
3" SCH 40 THREADED FLUSH JOINT
SLOTTED PVC PIPE OR SOIL GAS
COLLECTOR MAT SET WITHIN MIN 4"
BASE COURSE (SEE SPECIFICATION #3)
VERTICAL RISER AT SLAB PENETRATION WITH 90 DEGREE ELBOW
NTS
VAPOR LINER PENETRATION SEALED TO
PIPE PER MANUFACTURER INSTRUCTIONS
3" SCH 40 PVC 90 DEGREE ELBOW
STUD WALL
3" SCH 40 PVC RISER DUCT PIPE
(SEE SPECIFICATION #8 & #9)
BASE COARSE
(SEE SPECIFICATION #3)
THICKENED SLAB MAY NOT BE PRESENT IN
ALL LOCATIONS
3" SOLID SCH 40 PVC
(SEE SPECIFICATION #7)
VM2
8
SOLID TO SLOTTED 3" SCH 40
PVC PIPE TRANSITION (SLIP
COUPLING OR THREADED
JOINT)
A
333 WEST TRADE STREET
R C H I T E C T U R E
SUITE 200CHARLOTTE, NC 28202
T 704.927.9900
w w w. a x i o m a r c h i t e c t u r e . c o m
REVISIONS
PDP-001
VM-2
VAPOR
MITIGATION PLAN
DETAILS
AS-BUILTS
TR
Y
C
L
A
N

D
R
I
V
E

A
N
D

D
e
W
I
T
T

L
A
N
E
CH
A
R
L
O
T
T
E
,

N
O
R
T
H

C
A
R
O
L
I
N
A
EL
L
O

A
P
A
R
T
M
E
N
T
S
PR
O
F
F
I
T
T
-
D
I
X
O
N

P
A
R
T
N
E
R
S
VAPOR MITIGATION PLAN
PREPARED BY:
2923 South Tryon Street-Suite 100
Charlotte, North Carolina 28203
704-586-0007(p) 704-586-0373(f)
License # C-1269 / #C-245 Geology
ISSUED FOR CONSTRUCTION
FEBRUARY 7, 2024
S:\
A
A
A
-
M
a
s
t
e
r

P
r
o
j
e
c
t
s
\
P
r
o
f
f
i
t
t

D
i
x
o
n

-

P
D
P
\
P
D
P
-
0
0
1

-

T
r
y
c
l
a
n

A
v
e
n
u
e
\
V
I
M
S

i
n
s
t
a
l
l

r
e
p
o
r
t
\
F
i
g
u
r
e
s
\
V
M
P

A
s
-
B
u
i
l
t
s
_
2
.
6
.
2
4
.
d
w
g
,

v
m
-
2

d
e
t
a
i
l
s
,

S
V
i
n
c
e
n
t
C C
UP
10' X 25' LOADING SPACE
BUILDING ABOVE
BUILDING ABOVE
BUILDING ABOVE
GARAGE VENTILATION SHAFT
715.00
715.00
UP
POOL EQUIP.
CH
E
M

S
T
O
R
TRASH
ROOM
MAIN ELEC
ROOM
MAINTENANCE
OFFICE
TLT
BIKE
STORAGE
720.50
DOG SPA
BASEMENT
ENTRY
LOBBY
MP-1
MP-2/
MP-DUP
TMP-1
TMP-2
E-1
E-2
A1B-IAS-2
A1B-IAS-1/
IAS-DUP
A
333 WEST TRADE STREET
R C H I T E C T U R E
SUITE 200CHARLOTTE, NC 28202
T 704.927.9900
REVISIONS
VM-3
TR
Y
C
L
A
N

D
R
I
V
E

A
N
D

D
e
W
I
T
T

L
A
N
E
CH
A
R
L
O
T
T
E
,

N
O
R
T
H

C
A
R
O
L
I
N
A
PR
O
F
F
I
T
T
-
D
I
X
O
N

P
A
R
T
N
E
R
S
1/16" = 1'-0"A2.1
1 BASEMENT FLOOR PLAN
N
LEGEND
EXTENT OF VAPOR LINER
3" DIA SCH 40 SLOTTED PVC PIPE
3" DIA SCH 40 SOLID PVC VERTICAL RISER
WITH FAN IDENTIFICATION NUMBER (REFER
TO DETAIL #15 ON VM-2)
2" DIA SOLID PVC PRESSURE MONITORING
POINT WITH FLUSH-MOUNTED COVER
2" DIA SOLID PVC PRESSURE MONITORING
POINT WITH FLUSH-MOUNTED COVER -
SUB-SLAB SOIL GAS SAMPLE LOCATION
INDOOR AIR SAMPLE LOCATION
VIMS INSTALLATION COMPLETE. VIMS
INSTALLATION REPORT PREVIOUSLY
PROVIDED TO NCDEQ
E-7
TMP-2
MP-1
w w w. a x i o m a r c h i t e c t u r e . c o m
PDP-001
VAPOR
MITIGATION PLAN
SUB-SLAB LAYOUT
- BASEMENT
AS-BUILTS
VAPOR MITIGATION PLAN
PREPARED BY:
2923 South Tryon Street-Suite 100
Charlotte, North Carolina 28203
704-586-0007(p) 704-586-0373(f)
License # C-1269 / #C-245 Geology
3
VM2
2
VM2
1
VM2
4A
VM2
12
VM2
13
VM2
8
VM2
8
VM2
14
VM2
ISSUED FOR CONSTRUCTION
EL
L
O

A
P
A
R
T
M
E
N
T
S
FEBRUARY 6, 2024
S:\
A
A
A
-
M
a
s
t
e
r

P
r
o
j
e
c
t
s
\
P
r
o
f
f
i
t
t

D
i
x
o
n

-

P
D
P
\
P
D
P
-
0
0
1

-

T
r
y
c
l
a
n

A
v
e
n
u
e
\
V
I
M
S

i
n
s
t
a
l
l

r
e
p
o
r
t
\
F
i
g
u
r
e
s
\
V
M
P

A
s
-
B
u
i
l
t
s
_
2
.
6
.
2
4
.
d
w
g
,

v
m
-
3

b
a
s
e
m
e
n
t
,

S
V
i
n
c
e
n
t
UP
UP
UP
DN DN DN DN
BA
C
K
F
L
O
W
/
SP
R
I
N
K
L
E
R
PU
M
P

R
O
O
M
DN
DN
725.40
725.10
GARAGE VENTILATION SHAFT
ELECT/D
MECH
MECH
ELEC
TRASH
MECH T/D
725.92
725.00
DN
725.00
THE FRONT PORCH
727.00
ELEC.
MECH
TELE/DATA
DN
DN
GARAGE VENTILATION SHAFT
A3.2
158
A1.4
163
A1.4
161
C2.3-HC
159
A8
157
A3.5
129
B1
127
C2.2
125
A1.3
123 A7
121
A1.3
119
A6
117
A6
115 C2
113
B1
105
A3
111
A1
100
A2
102
A2.2
104
A2
106
C2
107
C6
108A6
110A6
112
A6.1
134
A1.1
150C5
149
A1.2
145
A1.2
144
A1.2
139
A6.2
135
C4
137
C4
136
A1.2
140
A3.1
141
A3.1
147
A3.1
142
A1.2
146
A1.2
143
A3.1
148
A3.6
118
C7
138
C2.3
126
A5
120
A3.6
116
C2
151
A3.6
114
A3.2
160
A3.2
162
A3.2
164
A3.4
101
A3.4
103
A3.5
128
A3.4-HC
124
A3.4
122
LEASING
141
LOUNGE
153
725.30
726.50
724.30
A3
130
DSDS
DS
DS
DS
DS
DS DS
DS DS
DS
DS
DS
DS
DS
DS
DS
DS
DS
DS
DS
DS DS DS
DS DS DS
DS
DS
DS
DS
DS DS
DS
DS
DS
DS
DS
DS
A1.3
133
A1.3
132
A1.3
131
726.00
726.00
OVERSIZED
PACKAGE
MECH
PACKAGE
STAIR 5
MECH
EL
E
C
.
CO
R
R
I
D
O
R
CORRIDOR
CORRIDOR
CO
R
R
I
D
O
R
STAIR 1
ELEV
LOBBY
STAIR 4
CORRIDOR
STAIR 3
STAIR 2
ELEV
LOBBY
A1.5
109
FITNESS
YOGA
RYTEK HIGH SPEED ROLL UP AUTOMOBILE GATES
POOL
COURTYARD
DR
Y
SP
R
I
N
K
L
E
R
RO
O
M
COWORKING
MECH
AWNING ABOVE
AWNING ABOVE
TE
L

/
DA
T
A
BUILDING PLAN NOTES1.2.3.4.ALL UNDESIGNATED DIMENSIONED INTERIOR WALLS TO BE 31/2" WOOD STUD.EXTERIOR WALLS & PLUMBING WALLS TO BE 5 1/2".ALL UNDIMENSIONED DOORS TO BE CENTERED OR TO BELOCATED 4 1/2" OFF SIDE WALL FRAMING TO FACE OF DOOR.SEE 1/4" UNIT PLANS FOR INTERIOR WALL LOCATIONS ANDADDITIONAL DETAILS.REFERENCE WALL TYPE SHEET (A7.0 - A7.15) FOR ALLINFORMATION ON CORRESPONDING WALL TAGS.11.REFER TO FINISH SCHEDULE FOR ALL INTERIOR WALL FINISHMATERIALS.12.SEE INTERIOR DESIGN DRAWINGS FOR ALL CEILING HEIGHTS,FINISHES, ETC. AT ALL AMENITY AREAS.13.PROVIDE TRANSITION STRIPS (SCHLUTER OR EQUAL) BETWEENDISSIMILAR FLOOR MATERIALS, ELEVATION CHANGE BETWEENTWO MATERIALS IS 1/2" MAX.14. SEE A12.2 FOR ALL TYPICAL ACCESSIBILITY DETAILS FOR ALLCOMMON AREAS.15.PROVIDE BLOCKING IN WALLS AS REQUIRED TO MEET ALLACCESSIBILITY REQUIREMENTS (SEE A12.0 - A12.2), AND ASNEEDED FOR SUPPORT OF CABINETS, SHELVES, HANDRAILS,ETC.5.ALL INTERIOR WOOD BEARING WALLS TO BE 1 HOUR FIRERATED (UL #305) - REFERENCE STRUCTURAL DRAWINGS FORALL LOCATIONS.6.ALL CORRIDOR TO UNIT WALLS TO BE 1 HOUR FIRE RATED -SEE WALL TYPE DESIGNATIONS AND SEE STRUCTURALDRAWINGS FOR SHEAR WALL LOCATIONS.7. ALL WOOD FRAME BALCONIES TO SLOPE 1/4" PER FOOT TOBALCONY EDGE SCUPPER OR DRAIN. ALL CONCRETEBALCONIES / TERRACES TO SLOPE 1/8" PER FOOT TOBALCONYEDGE, SCUPPER OR DRAIN.8.EXTERIOR FACE OF MASONRY VENEER SHALL BE 5 1/2” FROMEXTERIOR FACE OF FRAMING / CMU, UNLESS OTHERWISENOTED. MAINTAIN 1” MIN. AIRSPACE AT ALL MASONRYVENEER.9.SEE GRADING PLAN (CIVIL SHEETS) FOR BUILDING ENTRYELEVATION AND SITE WALL DIMENSIONS AND LOCATIONS.10.SEE ELECTRICAL PLANS FOR BUILDING ELECTRICAL LAYOUTS.
MP-7
MP-5
MP-4
MP-3
TMP-5
MP-6/SS-DUP
MP-8
MP-9
MP-10
MP-12
MP-13
MP-14
MP-11
VAN VAN
VA
N
SPRINKLER/
PUMP ROOM
UP
UP
DN
GARAGE VENTILATION SHAFT
GARAGE VENTILATION SHAFT
732.39
TMP-4
E-11
E-10
E-22
E-8 E-9
E-19
E-16
E-13
E-14
E-15
E-17
E-18
E-3
E-4
E-5
E-6
E-7
E-12
E-21
E-20
A1-IAS-1
A1-IAS-2/IAS-DUP
B-IAS-1
B-IAS-BKG
IAS-BKG
D-IAS-1
C-IAS-1 /
IAS-DUP
TMP-3
A
333 WEST TRADE STREET
R C H I T E C T U R E
SUITE 200CHARLOTTE, NC 28202
T 704.927.9900
w w w. a x i o m a r c h i t e c t u r e . c o m
REVISIONS
VM-4
TR
Y
C
L
A
N

D
R
I
V
E

A
N
D

D
e
W
I
T
T

L
A
N
E
CH
A
R
L
O
T
T
E
,

N
O
R
T
H

C
A
R
O
L
I
N
A
PR
O
F
F
I
T
T
-
D
I
X
O
N

P
A
R
T
N
E
R
S
1/16" = 1'-0"A2.1
1 LEVEL 1 FLOOR PLAN
N
LEGEND
EXTENT OF VAPOR LINER
3" DIA SCH 40 SLOTTED PVC PIPE
SOIL GAS COLLECTOR MAT (1" THICK AND
12" WIDE)
3" DIA SCH 40 SOLID PVC VERTICAL RISER
WITH FAN IDENTIFICATION NUMBER
(REFER TO DETAIL #15 ON VM-2)
2" DIA SOLID PVC PRESSURE MONITORING
POINT WITH FLUSH-MOUNTED COVER
2" DIA SOLID PVC TEMPORARY
MONITORING POINT
2" DIA SOLID PVC PRESSURE MONITORING
POINT WITH FLUSH-MOUNTED COVER -
SUB-SLAB SOIL GAS SAMPLE LOCATION
INDOOR AIR SAMPLE LOCATION
AREA C & D BUILDING CONSTRUCTION
PHASE
VIMS INSTALLATION COMPLETE. VIMS
INSTALLATION REPORT PREVIOUSLY
PROVIDED TO NCDEQ
E-5
MP-4
MP-5
MARCH 26, 2024
PDP-001
VAPOR
MITIGATION PLAN
SUB-SLAB LAYOUT
- FIRST FLOOR
AS-BUILTS
VAPOR MITIGATION PLAN
PREPARED BY:
2923 South Tryon Street-Suite 100
Charlotte, North Carolina 28203
704-586-0007(p) 704-586-0373(f)
License # C-1269 / #C-245 Geology
1
VM2
1
VM2
2
VM2
2
VM2
3
VM2
3
VM2
4A
VM2
4A
VM2
4B
VM2
4B
VM2
6
VM2
6
VM2
10
VM2
10
VM2
8
VM2
8A
VM2
11
VM2
13
VM2
9
VM2
7
VM2
14
VM2
ISSUED FOR CONSTRUCTION
7
VM2
D-IAS-1
EL
L
O

A
P
A
R
T
M
E
N
T
S
TMP-3
S:\
A
A
A
-
M
a
s
t
e
r

P
r
o
j
e
c
t
s
\
P
r
o
f
f
i
t
t

D
i
x
o
n

-

P
D
P
\
P
D
P
-
0
0
1

-

T
r
y
c
l
a
n

A
v
e
n
u
e
\
V
I
M
S

i
n
s
t
a
l
l

r
e
p
o
r
t
\
F
i
g
u
r
e
s
\
V
M
P

A
s
-
B
u
i
l
t
s
_
2
.
6
.
2
4
_
C
D
.
d
w
g
,

v
m
-
4

f
l
o
o
r

1
,

S
V
i
n
c
e
n
t

Appendix C

Product Specifications

PRODUCT PART #
VaporBlock® Plus™ 20 ................................................................ VBP20
UNDER-SLAB VAPOR / GAS BARRIER
Under-Slab Vapor/Gas Retarder
VAPORBLOCK® PLUS™VBP20
PRODUCT DESCRIPTION
VaporBlock® Plus™ is a seven-layer co-extruded barrier
made using high quality virgin-grade polyethylene and
EVOH resins to provide unmatched impact strength as well
as superior resistance to gas and moisture transmission.
VaporBlock® Plus™ 20 is more than 100 times less permeable
than typical high-performance polyethylene vapor retarders
against Methane, Radon, and other harmful VOCs. Tested and
verified for unsurpassed protection against BTEX, HS, TCE, PCE,
methane, radon, other toxic chemicals and odors.
VaporBlock® Plus™ 20 multi-layer gas barrier is manufactured
with the latest EVOH barrier technology to mitigate hazardous
vapor intrusion from damaging indoor air quality, and the safety
and health of building occupants. VBP20 is one of the most
effective underslab gas barriers in the building industry today
far exceeding ASTM E-1745 (Plastic Water Vapor Retarders
Used in Contact with Soil or Granular Fill Under Concrete Slabs)
Class A, B and C requirements. Available in a 20 (Class A) mil
thicknesses designed to meet the most stringent requirements.
VaporBlock® Plus™ 20 is produced within the strict guidelines
of our ISO 9001 Certified Management System.
PRODUCT USE
VaporBlock® Plus™ 20 resists gas and moisture migration
into the building envelop when properly installed to provide
protection from toxic/harmful chemicals. It can be installed as
part of a passive or active control system extending across the
entire building including floors, walls and crawl spaces. When
installed as a passive system it is recommended to also include
a ventilated system with sump(s) that could be converted to an
active control system with properly designed ventilation fans.
VaporBlock® Plus™ 20 works to protect your flooring and
other moisture-sensitive furnishings in the building’s interior
from moisture and water vapor migration, greatly reducing
condensation, mold and degradation.
SIZE & PACKAGING
VaporBlock® Plus™ 20 is available in 10’ x 150’ rolls to
maximize coverage. All rolls are folded on heavy-duty cores
for ease in handling and installation. Other custom sizes
with factory welded seams are available based on minimum
volume requirements. Installation instructions and ASTM E-1745
classifications accompany each roll.
© 2022 VIAFLEX, INC. All rights reserved.
APPLICATIONS
Radon Barrier
Methane Barrier
VOC Barrier
Brownfields Barrier
Vapor Intrusion Barrier
Under-Slab Vapor Retarder
Foundation Wall Vapor Retarder
VaporBlock® Plus™ is a seven-layer co-extruded barrier made using high quality virgin-grade polyethylene and EVOH resins to provide unmatched impact strength as well as superior resistance to gas and moisture transmission.
VaporBlock® Plus™ Placement
All instructions on architectural or structural drawings should be reviewed and followed.
Detailed installation instructions accompany each roll of VaporBlock® Plus™ and can also be located at www.ravenefd.com.
ASTM E-1643 also provides general installation information for vapor retarders.
VAPORBLOCK® PLUS™ 20
PROPERTIES TEST METHOD IMPERIAL METRIC
AppeArAnce White/Gold
Thickness, nominAl 20 mil 0.51 mm
WeighT 102 lbs/MSF 498 g/m²
clAssificATion ASTM E 1745 CLASS A, B & C
³ Tensile sTrengTh
ASTM E 154Section 9(D-882)58 lbf 102 N
impAcT resisTAnce ASTM D 1709 2600 g
permeAnce (neW mATeriAl)
ASTM E 154Section 7ASTM E 96Procedure B
0.0098 Perms
grains/(ft²·hr·in·Hg)
0.0064 Perms
g/(24hr·m²·mm Hg)
permeAnce (AfTer condiTioning)
(sAme meAsuremenT As Above permeAnce)
ASTM E 154Section 8, E96Section 11, E96Section 12, E96Section 13, E96
0.00790.00790.00970.0113
0.00520.00520.00640.0074
WvTr ASTM E 96Procedure B 0.0040 grains/hr-ft²0.0028 gm/hr-m²
benzene permeAnce See Note ⁶1.13 x 10-¹⁰ m²/sec or 3.62 x 10-¹³ m/s
Toluene permeAnce See Note ⁶1.57 x 10-¹⁰ m²/sec or 1.46 x 10-¹³ m/s
eThylbenzene permeAnce See Note ⁶1.23 x 10-¹⁰ m²/sec or 3.34 x 10-¹⁴ m/s
m & p-Xylenes permeAnce See Note ⁶1.17 x 10-¹⁰ m²/sec or 3.81 x 10-¹⁴ m/s
o-Xylene permeAnce See Note ⁶1.10 x 10-¹⁰ m²/sec or 3.43 x 10-¹⁴ m/s
hydrogen sulfide See Note 9 1.92E-⁰⁹ m/s
TrichloroeThylene (Tce) See Note ⁶7.66 x 10-¹¹ m²/sec or 1.05 x 10-¹⁴ m/s
perchloroeThylene (pce)See Note ⁶7.22 x 10-¹¹ m²/sec or 1.04 x 10-¹⁴ m/s
rAdon diffusion coeffiecienT K124/02/95 < 1.1 x 10-13 m2/s
meThAne permeAnce ASTM D 1434 3.68E-¹² m/sGas Transmission Rate (GTR):0.32 mL/m²•day•atm
mAXimum sTATic use TemperATure 180° F 82° C
minimum sTATic use TemperATure - 70° F - 57° C
UNDER-SLAB VAPOR / GAS BARRIER
VAPORBLOCK® PLUS™VBP20
³ Tests are an average of machine and transverse directions.5 Raven Industries performs seam testing at 20” per minute.6 Aqueous Phase Film Permeance.
Permeation of Volatile Organic Compounds through EVOH Thin Film Membranes and Coextruded LLDPE/EVOH/
LLDPE Geomembranes, McWatters and Rowe, Journal of Geotechnical and Geoenvironmental Engineering© ASCE/
September 2015. (Permeation is the Permeation Coefficient adjusted to actual film thickness - calculated at 1 kg/m³.)
The study used to determine PCE and TCE is titled: Evaluation of diffusion of PCE & TCE through high performance geomembranes by Di
Battista and Rowe, Queens University 8 Feb 2018.9 The study used to determine diffusion coefficients is titled: Hydrogen Sulfide (H₂S) Transport through Simulated Interim Covers with Conventional and Co-Extruded Ethylene-Vinyl Alcohol (EVOH) Geomembranes.
Scan QR Code to download technical data sheets.
Note: To the best of our knowledge, unless otherwise stated, these are typical property values and are intended as guides only, not as specification limits. Chemical resistance, odor transmission, longevity as well as other performance criteria is not implied or given and actual testing must be performed for applicability in specific applications and/or conditions. VIAFLEX MAKES NO WARRANTIES AS TO THE FITNESS FOR A SPECIFIC USE OR MERCHANTABILITY OF PRODUCTS REFERRED TO, no guarantee of satisfactory results from reliance upon contained information or recommendations and disclaims all liability for resulting loss or damage. Limited Warranty available at www.viaflex.com
VIAFLEX, INC.821 W Algonquin Street Sioux Falls, SD 57104 Ph: [phone] • TF: [phone]© 2022 VIAFLEX, INC. All rights reserved.27-0123 09/22
[e-mail] www.viaflex.com
INSTALLATION GUIDELINES - With VaporSeal™ Tape
VaporSeal™
4” Tape
Optional Butyl Seal
2-Sided Tape
Elements of a moisture/gas-resistant floor system. General illustration only.(Note: This example shows multiple options for waterstop placement.
VaporSeal™
4” Tape
VaporSeal™ 4” Tape
Fig. 2: VaporBlock® Plus™ Overlap Joint Sealing Methods
Fig. 1: VaporBlock® Plus™ Overlapping Roll-out Method
Please Note: Read these instructions thoroughly before installation to ensure proper use of VaporBlock® Plus™. ASTM E 1465, ASTM E 2121 and, ASTM E 1643 also provide valuable information regarding the installation of vapor / gas barriers. When installing this product, contractors shall conform to all applicable local, state and federal regulations and laws pertaining to residential and commercial building construction.
• When VaporBlock® Plus™ gas barrier is usedas part of an active control system for radon orother gas, a ventilation system will be required.
• If designed as a passive system, it is recommended to install a ventilation system that could beconverted to an active system if needed.
Materials List:VaporBlock® Plus™ Vapor / Gas BarrierVaporSeal™* 4” Seaming TapeVaporSeal™* 12” Seaming/Repair TapeButyl Seal 2-Sided TapeVaporBoot Plus Pipe Boots 12/Box (recommended)VaporBoot Tape (optional)POUR-N-SEAL™ (optional)1” Foam Weather Stripping (optional)Mako® Screed Supports (optional)
VAPORBLOCK® PLUS™ PLACEMENT
1.1. Level and tamp or roll granular base as specified. A base for a gas-reduction system may require a 4” to 6” gas permeable layer of clean coarse aggregate as specified by your architectural or structural drawings after installation of the recommended gas collection system. In this situation, a cushion layer consisting of a non-woven geotextile fabric placed directly under VaporBlock® Plus™ will help protect the barrier from damage due to possible sharp coarse aggregate.
1.2. Unroll VaporBlock® Plus™ running the longest dimension parallel with the direction of the pour and pull open all folds to full width. (Fig. 1)
1.3. Lap VaporBlock® Plus™ over the footings and seal with VIAFLEX Butyl Seal tape at the footing-wall connection. Prime concrete surfaces, when necessary, and assure they are dry and clean prior to applying VIAFLEX Butyl Seal Tape. Apply even and firm pressure with a rubber roller. Overlap joints a minimum of 6” and seal overlap with 4” VaporSeal™ Tape. When used as a gas barrier, overlap joints a minimum of 12” and seal in-between overlap with an optional 2-sided VIAFLEX Butyl Seal Tape. Then seal with 4” VaporSeal™ Tape centered on the overlap seam. (Fig. 2)
Page 1 of 4
To
p

o
r
i
g
i
n
a
l

d
i
a
g
r
a
m

a
n
d

f
i
g
u
r
e

#
1

w
e
r
e

r
e
p
r
i
n
t
e
d

w
i
t
h

p
e
r
m
i
s
s
i
o
n

b
y

t
h
e

P
o
r
t
l
a
n
d

C
e
m
e
n
t

A
s
s
o
c
i
a
t
i
o
n
.
Re
f
e
r
e
n
c
e
:

K
a
n
a
r
e
,

H
o
w
a
r
d

M
.
,

C
o
n
c
r
e
t
e

F
l
o
o
r
s

a
n
d

M
o
i
s
t
u
r
e
,

E
B
11
9
,

P
o
r
t
l
a
n
d

C
e
m
e
n
t

A
s
s
o
c
i
a
t
i
o
n
,

S
k
o
k
i
e
,

I
l
l
i
n
o
i
s
,

a
n
d

N
a
t
i
o
n
a
l

R
e
a
d
y

M
i
x
e
d

C
o
n
c
r
e
t
e

A
s
s
o
c
i
a
t
i
o
n
,

S
i
l
v
e
r

S
p
r
i
n
g
,

M
a
r
y
l
a
n
d
,

U
S
A
,

2
0
0
8
,

1
7
6

p
a
g
e
s
.
1.4. Seal around all plumbing, conduit, support columns or other penetrations that come through the VaporBlock® Plus™ membrane.
1.4a. Method 1: Pipes four inches or smaller can be sealed with VIAFLEX VaporBoot Plus preformed pipe boots. VaporBoot Plus preformed pipe boots are formed in steps for 1”, 2”, 3” and 4” PVC pipe or IPS size and are sold in units of 12 per box (Fig. 3 & 5).
Pipe boots may also be fabricated from excess VaporBlock® Plus™ membrane (Fig. 4 & 6) and sealed with VaporBoot Tape or VaporSeal™ Tape (sold separately).
1.4b. Method 2: To fabricate pipe boots from VaporBlock® Plus™ excess material (see Fig. 4 & 6 for A-F):
A)Cut a square large enough to overlap 12” in all directions.
B) Mark where to cut opening on the center of the square and cut four to eight slices about 3/8” less than the diameter of the pipe.
C) Force the square over the pipe leaving the tightly stretched cut area around the bottom of the pipe with approximately a 1/2” of the boot material running vertically up the pipe. (no more than a 1/2” of stretched boot material is recommended)
D) Once boot is positioned, seal the perimeter to the membrane by
applying 2-sided VIAFLEX Butyl Seal Tape in between the two layers. Secure boot down firmly over the membrane taking care not to have any large folds or creases.
E) Use VaporBoot Tape or VaporSeal™ Tape to secure the boot to the
pipe. VaporBoot Tape (option) – fold tape in half lengthwise, remove
half of the release liner and wrap around the pipe allowing 1” extra
for overlap sealing. Peel off the second half of the release liner
and work the tape outward gradually forming a complete seal.
VaporSeal™ Tape (option) - Tape completely around pipe
overlapping the VaporBlock® Plus™ square to create a tight seal
against the pipe.
F) Complete the process by taping over the boot perimeter edge with VaporSeal™ Tape to create a monolithic membrane between the surface of the slab and gas/moisture sources below and at the slab perimeter. (Fig. 4 & 6)
Preformed Pipe Boot Square Material Pipe Boot
Fig. 3
SINGLE PENETRATION PIPE BOOT INSTALLATION
Fig. 5 Fig. 6
1. Cut a square of VaporBlock® Plus™ barrier to extend at least12” from the pipe in all directions.
2. Cut four to eight slices about 3/8”less than the diameter of the pipe.
5. Use VIAFLEX VaporBoot orVaporSeal™ Tape andoverlap 1” at the seam.
4. Tape over the bootperimeter edge withVaporSeal™ Tape.
1. Cut out one of thepreformed boot steps(1” to 4”).
2. Tape the underside bootperimeter with 2-sidedButyl Seal Tape.
3. Force the boot overpipe and press tapefirmly in place.
4. Use VaporSeal™ Tape
to secure boot to thepipe.
5. Tape around entire bootedge with VaporSeal™Tape.
VaporBoot Flexible Tapeor VaporSeal™ 4” TapeVaporSeal™ 4” Tape
VaporBlock® Plus™Material
VaporSeal™ 4” Tape
VIAFLEX Butyl Seal2-Sided Tape VIAFLEX Butyl Seal2-Sided Tape
VaporBoot PlusPreformed Boot 12”(minimum)
3. Force over pipe and tape theunderside boot perimeter toexisting barrier with 2-sidedButyl Seal Tape.
Fig. 4
Page 2 of 4
Or
i
g
i
n
a
l

f
i
g
u
r
e

#
4

d
i
a
g
r
a
m

i
s

r
e
p
r
i
n
t
e
d

w
i
t
h

p
e
r
m
i
s
s
i
o
n

b
y

t
h
e

P
or
t
l
a
n
d

C
e
m
e
n
t

A
s
s
o
c
i
a
t
i
o
n
.
Method 1
Method 2
VaporSeal™4” Tape VaporBoot PlusPerformed Boot
VIAFLEX Butyl Seal 2-sided Tape VIAFLEX Butyl Seal 2-sided Tape
1.5. Sealing side-by-side multiple penetrations (option 1);
A) Cut a patch large enough to overlap 12” in all directions (Fig. 7)
of penetrations.
B) Mark where to cut openings and cut four to eight slices about
3/8” less than the diameter of the penetration for each.
C)Force patch material over penetration to achieve a tight fit and
form a lip.
D) Once patch is positioned, seal the perimeter to the membrane
by applying 2-sided VIAFLEX Butyl Seal Tape in-between the two layers. (Fig. 8)
E) After applying VIAFLEX Butyl Seal Tape between the patch
and membrane, tape around each of the penetrations and the
patch with VaporSeal™ 4” tape. (Fig. 9) For additional protection
apply POUR-N-SEAL™ or an acceptable polyurethane
elastomeric sealant around the penetrations. (Fig. 10)
Fig. 7 Fig. 8
Fig. 9 Fig. 10
MULTIPLE PENETRATION PIPE BOOT INSTALLATION
Fig. 6
Cut a patch large enough to overlap 12” in all directions and slide over penetrations (Make openings as tight as possible.)
Once the overlay patch is positioned, seal the perimeter to the membrane by applying 2-sided VIAFLEX Butyl Seal Tape in-between the two layers.
After applying VIAFLEX Butyl Seal Tape between the patch and membrane, tape around the perimeter of the penetration and the patch with VaporSeal™ 4” Tape.
For additional protection apply POUR-N-SEAL™ or an acceptable polyurethane elastomeric sealant around the penetrations.
VaporSeal™ 4” Tape VaporSeal™ 4” Tape
Page 3 of 4
Option 1
VIAFLEX Butyl Seal 2-sided Tape
1.6. POUR-N-SEAL™ method of sealing side-by-side multiple penetrations (option 2);
A) Install the vapor barrier as closely as possible to pipe penetrations tominimize the amount of POUR-N-SEAL™ necessary to seal around allpenetrations.
B) Once barrier is in place, remove soil or other particles with a dry clothor a fine broom to allow for improved adhesion to the POUR-N-SEAL™ liquid.
C) Create a dam around the penetration area approximately 2” awayfrom the pipe or other vertical penetrations by removing the releaseliner from the back of a 1” weather stripping foam and adhere to thevapor barrier. Form a complete circle to contain the POUR-N-SEAL™materials (Fig. 11).
D) Once mixed, pour contents around the pipe penetrations. If needed,a brush or a flat wooden stick can be used to direct the sealantcompletely around penetrations creating a complete seal (Fig. 12-13).
E) DO NOT leave excess POUR-N-SEAL™ in plastic container for longerthan the time it takes to pour sealant.
Fig. 12 Fig. 13
Fig. 11
Option 2
VAPORBLOCK® PLUS™ REPAIR INSTRUCTIONS
1.7. Proper installation requires all holes and openings are repaired prior
to placing concrete. When patching small holes, simply cut a 12” long
piece of 12” wide VaporSeal™ tape. Remove release liner and center
over the opening. Apply pressure to create a seal (Fig. 14-15).
1.8. When installing VaporBlock® Plus™ around pipe penetrations,
vertical columns, electrical ducts and other obstructions, you will
find it necessary to cut it to the nearest outside edge. This cut can
be easily sealed with 12” wide VaporSeal™ tape, by simply centering
it over the cut, 6” on either side. Once the tape is placed correctly,
apply pressure to assure a complete seal (Fig. 16).
Reminder Note: All holes or penetrations through the membrane will need
to be patched with 12” VaporSeal™ Tape.
Fig. 14
Page 4 of 5
Fig. 15
2.1. When installing reinforcing steel and utilities, in addition to the
placement of concrete, take precaution to protect VaporBlock®
Plus™. Carelessness during installation can damage the most
puncture–resistant membrane. Sheets of plywood cushioned with
geotextile fabric temporarily placed on VaporBlock® Plus™ provide
for additional protection in high traffic areas including concrete
buggies.
2.2. Use only brick-type or chair-type reinforcing bar supports to protect
VaporBlock® Plus™ from puncture.
2.3. Avoid driving stakes through VaporBlock® Plus™. If this cannot be
avoided, each individual hole must be repaired per section 1.7.
2.4. To avoid penetrating VaporBlock® Plus™ when installing screed
supports, utilize non-penetrating support, such as the Mako®
Screed Support System (Fig. 17). Avoid driving stakes through
VaporBlock® Plus™. If this cannot be avoided, each individual hole
must be repaired per figures 14-15.
2.5. If a cushion or blotter layer is required in the design between
VaporBlock® Plus™ and the slab, additional care should be given if
sharp crushed rock is used. Washed rock will provide less chance of
damage during placement. Care must be taken to protect blotter layer
from precipitation before concrete is placed.
VaporBlock® Plus™ Gas & Moisture Barrier can be identified on site
as gold/white in color printed in black ink with following logo and
classification listing (Fig. 18)
Page 5 of 5
VaporBlock® Plus™
Gas & Moisture Barrier
VAPORBLOCK® PLUS™ PROTECTION
Fig. 16
Fig. 18
Fig. 17
*Patent Pending
Note: To the best of our knowledge, unless otherwise stated, these are typical property values and are intended as guides only, not as specification limits. Chemical resistance, odor transmission, longevity as well as other performance criteria is not implied or given and actual testing must be performed for applicability in specific applications and/or conditions. VIAFLEX MAKES NO WARRANTIES AS TO THE FITNESS FOR A SPECIFIC USE OR MERCHANTABILITY OF PRODUCTS REFERRED TO, no guarantee of satisfactory results from reliance upon contained information or recommendations and disclaims all liability for resulting loss or damage. Limited Warranty available at www.viaflex.com
VIAFLEX, INC.
821 W Algonquin Street Sioux Falls, SD 57104 Ph: [phone] • TF: [phone]© 2022 VIAFLEX, INC. All rights reserved.27-0126 09/22
[e-mail] www.viaflex.com
ACCESSORIES
SEAMING TAPES & OTHER ACCESSORIES FOR PLASTIC SHEETING
Butyl Seal Tape (TP2BR / TP6BR)
Butyl Seal is a double-sided reinforced aggressive black butyl rubber tape used to join panels of polyethylene and polypropylene together by overlapping the edges and applying Butyl Seal in between. It is also used to adhere to concrete walls and footings when properly prepared. Butyl Seal is non-hardening and flexible. Available in 2” x 50’ and 6” x 50’ rolls.
R25B Tape (R25B)
R25B Tape is a single-sided aggressive synthetic elastomeric adhesive that bonds instantly to properly prepared polyethylene and polypropylene. The black polymer backing and adhesive is specially formulated to provide years of performance even in direct sunlight. A poly release liner provides for ease of installation. Available in 4” x 100’ roll.
ACCESSORY TAPES AND EPOXY
VaporBond™ Tape (TVB4)
VaporBond™ Tape is a white single-sided tape that combines a heavy-duty, weather-resistant polyethylene backing with an aggressive rubber adhesive. VaporBond™ Tape offers excellent seaming capabilities for our materials with an “Easy Tear” feature to reduce installation time. TVB4 has a WVTR of 0.18 perms per ASTM D3833. Typical applications include vapor retarders, covers and liners. Available in 4” x 210’ roll.
VaporSeal™ Tape (TVSP4/TVSP12)
VaporSeal™ Tape is a patent pending single-sided 7-layer gas barrier tape with a release liner for ease of installation. The backing contains a layer of highly impermeable EVOH designed to block migration of radon, methane, and VOC’s. An aggressive acrylic adhesive provides outstanding adhesion to polyethylene over a wide temperature range. Typical uses include joining, repairing and sealing gas/moisture barriers. Available in 4” x 160’ and 12” x 50’ rolls.
VaporBoot™ Tape (TBOOT)
VaporBoot™ Tape is a single-sided elastomeric butyl tape used to complete pipe boot installations (sealing the boot to the pipe). The 100% stretchable butyl adhesive features excellent adhesion values and 3-D stretching that can be easily molded to multiple surfaces without any creases and folds. Available in 2” x 16.4’ roll.
ADDITIONAL ACCESSORIES
VaporBoot™ System (VBOOT)
The VaporBoot™ System is designed to assist in securing pipe and other penetrations that run vertically through the vapor reta rder material. The VaporBoot™ System offers a quick solution and is delivered to the jobsite in a complete package. VaporBoots are produced from high performance VaporBlock® material.
Package Contents: 25 - VaporBoots (18” x 18”, w/precut center marker) 1 Roll VaporBoot (TBOOT)Tape 2‘x16.4‘1 roll of Vapor Bond Tape (TVB4) 4‘x210
VaporBoot™ Plus Preformed Pipe Boots (VBPBT)
VaporBoot™ Plus Preformed Pipe Boots are produced from heavy 40 mil co-extruded polyethylene and barrier resins for excellent strength and durability. The preformed boots are stepped to fit 1” to 4” wide pipe penetrations. VaporBoot™ Plus Preformed Pipe Boots are available in quantities of 12 per box.
From tie-d own fasteners to field seaming tape, Viaflex has the accessories you need to maximize your film’s versatility and minimize installation time on the job.
POUR-N-SEAL™ (PNS1G)
POUR-N-SEAL™ is a gray two part epoxy used to seal around multi-pipe penetrations in areas where pipe boots are not practical, when installing underslab barriers. The POUR-N-SEAL™ system installation guide references a 1” x 25 lineal feet adhesive-backed foam to form a dam around multi-pipe penetrations to contain POUR-N-SEAL™ during the setting process. The 1” x 25 ft. adhesive-backed foam is sold seperately as FOAM25.
© 2022 VIAFLEX, INC. All rights reserved.
ACCESSORIES
Tie-Down Buttons (BUTI) & Tarp Grabbers (BUTEZ)
Tie-Down Buttons and Tarp Grabbers help keep plastic sheeting securely in place. Tie-Down Buttons are designed to eliminate traditional grommets in plastic sheeting up to 10 mil thick and are reusable plastic fittings that are easy to install in any position. Tarp Grabbers are up to 4 times stronger than a brass grommet and are typically used in heavier plastic sheeting from 10 mil to 30 mil thick. Great for equipment covers, large storage covers and truck tarps.
ADDITIONAL ACCESSORIES (CONTINUED)
Dura♦Skrim® Reinforced Sandbags
Dura♦Skrim® reinforced sandbags are used to secure large covers and liners to prevent wind damage. Sandbags are produced with strong Dura♦Skrim® 8 & 12 mil reinforced polyethylene. These 15” wide x 24” long bags are designed to hold 35 lbs. Sandbags are also available in other VIAFLEX reinforced materials with minimum order requirements. 11.8” Cable Ties are also available.
Dura-Clip™ (CLIP11)
VIAFLEX Welding Rod
These full size clips are 11” long and fit most commercial scaffolding. Dura-Clip™ will securely fasten your poly sheeting to scaffolding, reducing wind whip and increasing the life of your enclosure. The Dura-Clip™ is normally placed about every 3’ onto the enclosure.
VIAFLEX Welding Rod is used for field seaming, repairs and detail work, such as installing pipe boots. Packaged in 25 lb spools, it is available in 4mm and 5mm sizes to fit most brands of extrusion guns. VIAFLEX Welding Rod is made from a thermally UV stabilized LLDPE resin and is available in both black and white to correspond with the color of geomembranes being utilized.
SEAMING TAPES & OTHER ACCESSORIES FOR PLASTIC SHEETING
TAPE ACCESSORY PROPERTIES
PROPERTIES VaporBond Tape(TVB4)VaporSeal Tape(TVSP4 / TVSP12)VaporBoot Tape(TBOOT)R25B Tape(R25B)Butyl Seal Tape(TP2BR / TP6BR)
Backing 6.7 mil Polyethylene 7 mil EVOH/LLDPE 30 mil EPDM 8 mil Multi-Polymer N/A
Adhesive 3.3 mil Rubber Based
Pressure-Sensitive
2 mil Acrylic Adhesive
Pressure-Sensitive
20 mil
Butyl Rubber
17 mil
Synthetic Elastomeric
40 mil
Butyl Rubber
Color White Silver Black Black Black
Type Single Sided Single Sided Single Sided Single Sided Double Sided
Size 4” x 210’4” x 160’ / 12” x 50’2” x 16.4’4” x 100’2” x 50’ / 6” x 50’
Rolls per Case 12 12 / 4 64 6 16 / 4
Weight per Case 45 lbs 50 lbs / 18 lbs 45 lbs 33 lbs 47 lbs / 20 lbs
Adhesion Values 35 oz. / in. (to steel)80 oz. / in. (to steel)145 oz. / in. (to steel)144 oz. / in. (to steel)88 oz. / in. (to steel)
Perms 0.081 g/(24h*100 in²)0.014 g/(24h*100 in²)N/A <0.005 g/(24h*100 in²)0.82 g/(24h*100 in²)
Service Temp.-40° F to +180° F -40° F to +190° F +14° F to +122° F +20° F to +180° F 0° F to +170° F
Min.Application Temp.50° F 50° F 14° F 35° F 35° F
Ideal StorageTemp. / Humidity 70° F w/ 40-50 %60°-80° F w/ 40-60 %70° F w/ 70 %70° F w/ 40-50 %70° F w/ 40-50 %
Note: To the best of our knowledge, unless otherwise stated, these are typical property values and are intended as guides only, not as specification limits. Chemical resistance, odor transmission, longevity as well as other performance criteria is not implied or given and actual testing must be performed for applicability in specific applications and/or conditions. VIAFLEX MAKES NO WARRANTIES AS TO THE FITNESS FOR A SPECIFIC USE OR MERCHANTABILITY OF PRODUCTS REFERRED TO, no guarantee of satisfactory results from reliance upon contained information or recommendations and disclaims all liability for resulting loss or damage. Limited Warranty available at www.viaflex.com
27-0016 05/23
[e-mail] www.viaflex.comScan QR Code to download technical data sheets.
VIAFLEX, INC.
821 W Algonquin Street Sioux Falls, SD 57104 Ph: [phone] • TF: [phone]© 2022 VIAFLEX, INC. All rights reserved.

 

 !"#$%&'(()'))*+'&"'%),-./01,
..
,01,0. 
,
234567589 :;<=>?;<@AB=;>;>;BCD<E<;FGHBIH;>BAHBJ=K:;;BLA>G?AHBG<=>KMNNOPONQMRSTUVWXYZXXR[\O]^_]`Q^Ma[b
cd;BBDFIH<DD>IHA>eD?Ae<=HABDF?<;@BCDd=KCBDIBHdAIIfg2B;BCDCDAh=DIB5iDHA>Id;BE=ED?<;@jklmBC<;GKCjnmF=A@DBD<A>FGEB;lopdD>KBCI5cd;`ars^rON`NO`t`^u`vuOs^Qw`t`N^OQxMP]Ma_yzI=edD|FDED>F=>K;>Id;BI=qD|IEAH=>KA>F>G@eId;BI53<;}H;>I=IBI;?Id;BI|>;<@Add~IEAHDFAhAdI|HGBED<ED>F=HGdA<B;BCDA=I;?BCDE=EDA>?<;@;>DD>F;?BCDE=EDB;BCD;BCD<5L;IBE=EDGEB;B};<;}I@;<DBCA>BCDIBABDFF=A@DBD<;s^QwMzQ[^ya^_]`aQ[QNz]QzN`usO` Oa^aybS]NOOa]`avOPzNa^[wOrs^Qw‚z[wZQwNO`rOrMN[u^\ƒM^a]MatOaQ^Ma`u_QQ^ay[b„…†‡ˆ‰Š‡‹Œ „…†‡ˆ‰Š‡ Œ „Ž  ‘ „•–—–˜™š#$››•–—–˜™š#$››•–—–˜™š#$››•–—–j9 mjj {{j59jšj5žžoj58ool59Ÿš95šooœ5šoo{ž5žlšn5žlšjo5Ÿšojl5Ÿšo {{{{{{{{š5šž9{{{{5nœoj5ošoj59jšj5žžoj58ool59Ÿš95šooœ5šoo{ž5žlšn5žlš{{5jœŸ5jšœ5jŸ85j8j5loo5ljn59oo599Ÿ{5œ9l5šoo{{{{5j995jœo5jœš5jšœ5ljž5l9Ÿ{5lno59ll59žš5œož {{{{{{{{59lŸ{{{{{{{{{{{œ5šooš5šž9{{{{



 

 !"+,-$
3 467/86190:23.;60<=>9?8;9=?946050<50A9?4546GIJKLMNOPLGQJRSTUDEVNKKDWXdaea`f[eg]_h[`[eZ]Z[_i_]j_kj[deahl]mnaa`o_bpd_\`pe]bmq
(uv&wywxz#(uv&wywxz#X++Q X+G+ X+GI X+G{X+I+ X+I{ X+IQ X+*+X+|+3::33}}~~~3::33}}~~~
€€3:3:}3}3::::  ::::3~3~}}}}~:~::€:€ ~: ~:333333:3€3€}}}}€~3€~3:::}}}}~~}}}}}~ 3~ 3:: 3  3  3 ~3 ~}3~}3 ~ ~:3:3:3~~:}:}:3:3: : : :~3











  ! !"#$ ! !"
%&'()(**+,
,


















 
 






 





!
"#


$
 


 
%% &'()*' '+,)-./-012+,(2.
%% &'()*3 3+,04./3)1-4+,2(.
%% &'()*( (+,-*'./3)1-4+,2(.
%% &'()*' '+,)-./ -012+,(2.
%% &'()*3 3+,04./ 3)1-4+,2(.
%% &'()*( (+,-*'./3)1-4+,2(.

 

   

     

 



!
"" 
#
5
"

"" $


 







Appendix D

Photographic Log and Inspection Checklist

Photograph Nos. 1 & 2: Representative views of sub-slab gravel and vapor conveyance
piping in Area C.
PD
P
.
0
0
1
2923 S. Tryon Street, Suite 100
Charlotte, NC 28203
704.586.0007(p) 704.586.0373(f)
BATTERY AND IGNITION DISTRIBUTION
TRYCLAN DRIVE AND ELLENWOOD PLACE
CHARLOTTE, NORTH CAROLINA
Photograph Nos. 3 & 4: Representative view of sub-slab gravel and vapor conveyance
piping in Area D.
Photograph Nos. 7 & 8: Representative views of Viaflex VBP-20 vapor barrier system in
Area D.
PD
P
.
0
0
1
2923 S. Tryon Street, Suite 100
Charlotte, NC 28203
704.586.0007(p) 704.586.0373(f)
BATTERY AND IGNITION DISTRIBUTION
TRYCLAN DRIVE AND ELLENWOOD PLACE
CHARLOTTE, NORTH CAROLINA
Photograph Nos. 5 & 6: Representative view of Viaflex VBP-20 vapor barrier system in
Area C.
2923 S. Tryon Street, Suite 100
Charlotte, NC 28203
704.586.0007(p) 704.586.0373(f)PD
P
.
0
0
1
BATTERY AND IGNITION DISTRIBUTION
TRYCLAN DRIVE AND ELLENWOOD PLACE
CHARLOTTE, NORTH CAROLINA
Photograph Nos. 9 & 10: Representative riser installations in interior wall.
Photograph Nos. 11 & 12: Representative views of rooftop exhaust vents and labeling.
2923 S. Tryon Street, Suite 100
Charlotte, NC 28203
704.586.0007(p) 704.586.0373(f)PD
P
.
0
0
1
BATTERY AND IGNITION DISTRIBUTION
TRYCLAN DRIVE AND ELLENWOOD PLACE
CHARLOTTE, NORTH CAROLINA
Category Example Criteria
Proper base layer (i.e., gravel, aerated flooring) and thickness
Proper placement, type, and pitch of VIMS vent piping
Proper placement, type, and pitch of monitoring points
Correct vapor barrier type
elevators, etc.)
Good condition of vapor barrier
Riser pipe material and fitting connections
Proper pitch towards sub-slab (gravity drain)
Appropriate VIMS labels
Correct fan/ventilator
Fan/ventilator operation
Proper fittings and protection (varmint screens, electrical covers, etc.)
Appropriate VIMS labels
Proper distance from roof intakes and parapets
Pilot test completed
Monitoring points finished and accessible
Vapor Intrusion Mitigation System - Inspection Checklist
Building/Area ID: Area C and Area D
Start Date and End Date: October 2022 - July 2023
Proper Installation
(Initial below)
Site Name and H&H Project #: Battery & Ignition Distribution - Ello House; PDP.001
DEQ Brownfields ID: 23055-19-060
Sub-Slab
Vapor Barrier
Vent Riser Piping
JCG
JCG
JCG
JCG
JCG
JCG
Pilot Test / Checkout
JCG
JCG
JCG
JCG
JCG
JCG
JCG
Fan/Ventilator
JCG
JCG
JCG
JCG

Appendix E

VIMS Influence Testing Forms and Sampling Field Forms

Table E-1Summary of Influence Testing Results
Ello House
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
H&H Job No. PDP.001
Point ID Baseline Initial 10-minute Point ID Baseline Initial 10-minute Point ID Baseline Initial 10-minute
E-8 0.000 -3.142 -3.096 E-9 0.000 -3.094 -2.870 E-14 0.000 -2.973 -3.002
E-11 0.000 -4.201 -3.877 E-10 0.000 -3.288 -3.542 **MP-9 0.000 -0.110 -0.109
E-14*0.000 -2.921 -2.853 E-12 0.000 -3.270 -3.080
E-16*0.000 -2.782 -2.573 E-13*0.000 -2.718 -2.512
E-18 0.000 -2.828 -2.642 E-15*0.000 -2.607 -2.729
E-20 0.000 -3.703 -2.956 E-17*0.000 -2.671 -2.754
E-22 0.000 -3.011 -2.988 E-19 0.000 -3.110 -3.135
TMP-5 0.000 -0.005 -0.004 E-21 0.000 -3.150 -3.028
MP-6 0.000 -0.117 -0.120 TMP-5 0.000 -0.171 -0.175
MP-7 0.000 -0.137 -0.138 MP-6 0.000 -0.043 -0.043
MP-8 0.000 -0.003 0.000 MP-7 0.000 -0.076 -0.074
MP-9**NM NM NM MP-8 0.000 -0.279 -0.285
MP-10 0.000 -0.181 -0.182 **MP-9 NM NM NM
MP-11 0.000 -0.077 -0.078 MP-10 0.000 -0.114 -0.260
MP-12 0.000 -0.070 -0.073 MP-11 0.000 -0.448 -0.544
MP-13 0.000 -0.124 -0.123 MP-12 0.000 -0.022 -0.039
MP-14 0.000 -0.124 -0.124 MP-13 0.000 -0.182 -0.181
MP-14 0.000 -0.249 -0.281
Notes:
**MP-9 was tested on 8/24/23 after repairs were made to the monitoring point.
Fans Utilized: AMG Eagle Extreme, Legend, and Legend Extreme
MP-9 RE-TEST
8/24/20233/29/2023
Test 2Test 1
3/29/2023
https://harthick.sharepoint.com/sites/MasterFiles-1/Shared Documents/AAA-Master Projects/Proffitt Dixon - PDP/PDP-001 - Tryclan Avenue/VIMS install report/Areas C and D/Tables/PDP-001 Pilot Test Data Hart & Hickman, PC
Table E-1
Summary of Influence Testing Results
Ello House
Tryclan Drive and Ellenwood Place
Charlotte, North Carolina
H&H Job No. PDP.001
Point ID Baseline Initial 10-minute Point ID Baseline Initial 10-minute
E-3 0.000 -2.376 -2.438 E-1 0.000 -3.662 -3.207
E-4 0.000 -3.041 -3.055 TMP-1 0.000 -0.986 -1.102
E-5 0.000 -3.077 -3.079 MP-1 0.000 -1.106 -1.145
E-6 0.000 -4.819 -4.838
E-7 0.000 -3.020 -3.053
TMP-3 0.000 -0.233 -0.232
TMP-4 0.000 -0.336 -0.363 Point ID Baseline Initial 10-minute
MP-3 0.000 -0.795 -0.810 E-2 0.000 -4.421 -4.436
MP-4 0.000 -1.249 -1.292 TMP-2 0.000 -0.324 -0.326
MP-5 0.000 -0.518 -0.516 MP-2 0.000 -0.224 -0.225
Basement (North)
3/30/2023
https://harthick.sharepoint.com/sites/MasterFiles-1/Shared Documents/AAA-Master Projects/Proffitt Dixon - PDP/PDP-001 - Tryclan Avenue/VIMS install report/Areas C and D/Tables/PDP-001 Pilot Test Data
Page 2 of 2
Hart & Hickman, PC
MP-3
13711 SS Perm.Conc Full 50 Pump 13.0 Yes
17727
MP-5/MP-DUP
13694/15804 Conc
13110
PDP-001 JL 50s F & sunny
MP-3 1 L13711 2/21/24 10
0.1 L/min
1155 -16 50 44 32
17727 1200 -5
1150 -28
57
MP-5 / MP-DUP 1 L 1557 -29
13694/15804 2/21/24 10 1602 -16 59 32 60 28
0.1 L/min13110 1607 -5
50s F & sunny
C-IAS-1 / IAS-DUP 6 L37239 / 36110 2/20/24-
2/21/24 1702 -25 64
0.25 L/min 1132 -7 64
D-IAS-1 1124 -30 636 L
IAS-BKG
46855 1707 -24 NA
1130 1700
30.35 30.29
E E
6 6
INDOOR AIR BUILDING SURVEY
and SAMPLING FORM
Site Name: ____________________________________
Preparer’s name: ________________________________
Preparer’s affiliation: ____________________________
#: ______________________
Date: __________________________
Phone #: _______________________
Part I - Occupants
Building Address: ____________________________________________________________________
Property Contact: _______________________________ Owner / Renter / other: ______________
Contact’s Phone: home ( )__________ work ( )______________ cell ( )____________
# of Building occupants: Children under age 13 _____ Children age 13-18 ______ Adults _____
Part II – Building Characteristics
Building type:
Describe building: ________________________________________ Year constructed: _________
Sensitive population:(specify): _______________
Number of floors below grade: ______
Number of floors at or above grade: ______
Depth of basement below grade surface: ______ ft. Basement size: _______ ft2
Basement floor construction:
Foundation walls:
Basement sump present?Sump pump?
ther (specify): ________________
other (specify)_______________
Water in sump?
Type of heating system (c all that apply):
hot air circulation hot air radiation wood steam radiation
heat pump hot water radiation kerosene heater electric baseboard
other (specify): ________________________
Type of ventilation system (c all that apply):
bathroom ventilation fans
outside air intake
central air conditioning mechanical fans
individual air conditioning units kitchen range hood fan
other (specify): _________________
Type of fuel utilized (c all that apply):
Natural gas electric fuel oil wood coal solar kerosene
Are the basement walls or floor sealed with waterproof paint or epoxy coatings?
other (specify) _____________
Is there a whole house fan?
Septic system?
Irrigation/private well?
Type of ground cover outside of building:
Existing subsurface depressurization (radon) system in place?
Sub-slab vapor/moisture barrier in place?
Type of barrier: ____________________________
Part III - Outside Contaminant Sources
Other stationary sources nearby (gas stations, emission stacks, etc.): _____________________________
Heavy vehicular traffic nearby (or other mobile sources): ______________________________________
Part IV – Indoor Contaminant Sources
Identify all potential indoor sources found in the building (including attached garages), the location of
the source (floor and room), and whether the item was removed from the building 48 hours prior to
indoor air sampling event. Any ventilation implemented after removal of the items should be completed
at least 24 hours prior to the commencement of the indoor air sampling event.
Potential Sources Location(s)Removed
(Yes / No / NA)
Gasoline storage cans
Gas-powered equipment
Kerosene storage cans
Paints / thinners / strippers
Cleaning solvents
Oven cleaners
Carpet / upholstery cleaners
Other house cleaning products
Moth balls
Polishes / waxes
Insecticides
Furniture / floor polish
Nail polish / polish remover
Hairspray
Cologne / perfume
Air fresheners
Fuel tank (inside building)
Wood stove or fireplace
New furniture / upholstery
New carpeting / flooring
Hobbies - glues, paints, etc.
Part V – Miscellaneous Items
Do any occupants of the building smoke?How often? ______________
Last time someone smoked in the building? ____________ hours days ago
Does the building have an attached garage directly connected to living space?
If so, is a car usually parked in the garage?
Are gas-powered equipment or cans of gasoline/fuels stored in the garage?
Do the occupants of the building have their clothes dry cleaned?
If yes, how often?
Do any of the occupants use solvents in work?
If yes, what types of solvents are used? _______________________________________
If yes, are their clothes washed at work?
If so, when and which chemicals? _________________________________________________
Has there ever been a fire in the building?If yes, when? _____________
Has painting or staining been done in the building in the last 6 months?Yes No
If yes, when __________________ and where? ____________________________
Part VI – Sampling Information
Sample Technician: ____________________________ Phone number:) _______ - __________
Sample Source
Sampler Type
Other (specify): _________________
Analytical Method:ther: _____________ Cert. Laboratory:
Sample locations (floor, room):
Field ID # _____ - ________________________ Field ID # _____-__________________________
Field ID #
Were “Instructions for Occupants” followed?
Provide Drawing of Sample Location(s) in Building
Part VII - Meteorological Conditions
Was there significant precipitation within 12 hours prior to (or during) the sampling event?Yes No
Describe the general weather conditions: _________________________________________________
_____________________________________________________________________________________
Part VIII – General Observations
Provide any information that may be pertinent to the sampling event and may assist in the data
interpretation process (e.g., observed that drycleaner operated with door or windows propped open for
ventilation).
(Adapted from the NJDEP Vapor Intrusion Guidance, October 2005)
Sunny, 50's F; no precipitation

Appendix F

Laboratory Analytical Report

Laboratory's liability in any claim relating to analyses performed shall be limited to, at laboratory's option, repeating the
analysis in question at laboratory's expense, or the refund of the charges paid for performance of said analysis.

3/8/2024
Hart & Hickman (Charlotte) David Kahn
2923 South Tryon St. Ste 100 Charlotte, NC, 28203
Ref: Analytical Testing
Lab Report Number: 24-053-0009 Client Project Description: PDP-001
Dear David Kahn:
Waypoint Analytical, LLC (Charlotte) received sample(s) on 2/22/2024 for the analyses presented in the
following report.
The above referenced project has been analyzed per your instructions. The analyses were performed in accordance with the applicable analytical method.
The analytical data has been validated using standard quality control measures performed as required by the
analytical method. Quality Assurance, method validations, instrumentation maintenance and calibration for all parameters were performed in accordance with guidelines established by the USEPA (including 40 CFR 136
Method Update Rule May 2021) unless otherwise indicated. Certain parameters (chlorine, pH, dissolved oxygen, sulfite...) are required to be analyzed within 15 minutes of sampling. Usually, but not always, any field parameter analyzed at the laboratory is outside of this holding time.
Refer to sample analysis time for confirmation of holding time compliance.
The results are shown on the attached Report of Analysis(s). Results for solid matrices are reported on an as-received basis unless otherwise indicated. This report shall not be reproduced except in full and relates only to
the samples included in this report. Please do not hesitate to contact me or client services if you have any questions or need additional information. Sincerely,
Angela D Overcash Senior Project Manager
Page 1 of 38
Certification Summary
Laboratory ID: WP CNC: Waypoint Analytical Carolina, Inc. (C), Charlotte, NC
State Program Lab ID Expiration Date
07/31/202437735State ProgramNorth Carolina
12/31/2024402State ProgramNorth Carolina
07/31/202499012State ProgramSouth Carolina
12/31/202399012State ProgramSouth Carolina
Page 1 of 1 00016/24-053-0009
Page 2 of 38
Report Number:
Sample Summary Table
Client Project Description:
24-053-0009
PDP-001
Lab No Client Sample ID Matrix Date Collected Date Received
02/20/2024Air 97578 IAS-DUP 02/22/2024 09:50
02/20/2024 11:32Air 97579 C-IAS-1 02/22/2024 09:50
02/20/2024 11:24Air 97580 D-IAS-1 02/22/2024 09:50
02/20/2024 11:23Air 97581 IAS-BKG 02/22/2024 09:50
02/21/2024Air 97582 MP-DUP 02/22/2024 09:50
02/21/2024 15:57Air 97583 MP-5 02/22/2024 09:50
02/21/2024 11:50Air 97584 MP-3 02/22/2024 09:50
Page 3 of 38
Summary of Detected Analytes
QualifiersAnalyzedUnitsResult
Report Number:
Client Sample ID
Method Parameters
Lab Sample ID
24-053-0009
Report Limit
Project:PDP-001
V 97578IAS-DUP
114 02/28/2024 03:02TO-15 Acetone µg/m3 2.02
2.29 02/26/2024 23:12TO-15 Benzene µg/m3 0.073
J0.949 02/26/2024 23:12TO-15 Chloromethane µg/m3 0.067
2.89 02/26/2024 23:12TO-15 Dichlorodifluoromethane µg/m3 0.134
3.20 02/26/2024 23:12TO-15 Ethylbenzene µg/m3 0.106
J1.93 02/26/2024 23:12TO-15 4-Ethyltoluene µg/m3 0.128
J0.582 02/26/2024 23:12TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
2.41 02/26/2024 23:12TO-15 Heptane µg/m3 0.143
2.58 02/26/2024 23:12TO-15 n-Hexane µg/m3 0.047
B6.33 02/26/2024 23:12TO-15 Isopropyl Alcohol µg/m3 0.139
65.8 02/26/2024 23:12TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
J1.63 02/26/2024 23:12TO-15 Methylene Chloride µg/m3 0.488
J0.560 02/26/2024 23:12TO-15 Naphthalene µg/m3 0.183
2.14 02/26/2024 23:12TO-15 Styrene µg/m3 0.124
25.6 02/26/2024 23:12TO-15 Tetrahydrofuran µg/m3 0.107
11.4 02/26/2024 23:12TO-15 Toluene µg/m3 0.090
J1.74 02/26/2024 23:12TO-15 Trichlorofluoromethane µg/m3 0.130
10.2 02/26/2024 23:12TO-15 1,2,4-Trimethylbenzene µg/m3 0.110
2.77 02/26/2024 23:12TO-15 1,3,5-Trimethylbenzene µg/m3 0.236
11.4 02/26/2024 23:12TO-15 o-Xylene µg/m3 0.157
12.5 02/26/2024 23:12TO-15 m,p-Xylene µg/m3 0.217
23.9 02/26/2024 23:12TO-15 Xylene (Total)µg/m3 0.157
V 97579C-IAS-1
118 02/28/2024 03:38TO-15 Acetone µg/m3 2.02
2.22 02/27/2024 00:02TO-15 Benzene µg/m3 0.073
J0.947 02/27/2024 00:02TO-15 Chloromethane µg/m3 0.067
2.87 02/27/2024 00:02TO-15 Dichlorodifluoromethane µg/m3 0.134
3.23 02/27/2024 00:02TO-15 Ethylbenzene µg/m3 0.106
J1.88 02/27/2024 00:02TO-15 4-Ethyltoluene µg/m3 0.128
J0.590 02/27/2024 00:02TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
2.17 02/27/2024 00:02TO-15 Heptane µg/m3 0.143
2.51 02/27/2024 00:02TO-15 n-Hexane µg/m3 0.047
B6.34 02/27/2024 00:02TO-15 Isopropyl Alcohol µg/m3 0.139
65.0 02/27/2024 00:02TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
J1.08 02/27/2024 00:02TO-15 Methylene Chloride µg/m3 0.488
J0.571 02/27/2024 00:02TO-15 Naphthalene µg/m3 0.183
Page 4 of 38
Summary of Detected Analytes
QualifiersAnalyzedUnitsResult
Report Number:
Client Sample ID
Method Parameters
Lab Sample ID
24-053-0009
Report Limit
Project:PDP-001
V 97579C-IAS-1
J2.11 02/27/2024 00:02TO-15 Styrene µg/m3 0.124
25.0 02/27/2024 00:02TO-15 Tetrahydrofuran µg/m3 0.107
9.65 02/27/2024 00:02TO-15 Toluene µg/m3 0.090
J1.65 02/27/2024 00:02TO-15 Trichlorofluoromethane µg/m3 0.130
10.3 02/27/2024 00:02TO-15 1,2,4-Trimethylbenzene µg/m3 0.110
2.69 02/27/2024 00:02TO-15 1,3,5-Trimethylbenzene µg/m3 0.236
11.1 02/27/2024 00:02TO-15 o-Xylene µg/m3 0.157
12.4 02/27/2024 00:02TO-15 m,p-Xylene µg/m3 0.217
23.5 02/27/2024 00:02TO-15 Xylene (Total)µg/m3 0.157
V 97580D-IAS-1
263 02/28/2024 04:14TO-15 Acetone µg/m3 4.04
J1.20 02/27/2024 00:49TO-15 Benzene µg/m3 0.073
J0.972 02/27/2024 00:49TO-15 Chloromethane µg/m3 0.067
2.83 02/27/2024 00:49TO-15 Dichlorodifluoromethane µg/m3 0.134
J1.81 02/27/2024 00:49TO-15 Ethylbenzene µg/m3 0.106
J0.958 02/27/2024 00:49TO-15 4-Ethyltoluene µg/m3 0.128
J0.590 02/27/2024 00:49TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
J1.31 02/27/2024 00:49TO-15 Heptane µg/m3 0.143
J1.32 02/27/2024 00:49TO-15 n-Hexane µg/m3 0.047
B9.13 02/27/2024 00:49TO-15 Isopropyl Alcohol µg/m3 0.139
59.3 02/27/2024 00:49TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
J1.47 02/27/2024 00:49TO-15 Methylene Chloride µg/m3 0.488
J1.63 02/27/2024 00:49TO-15 Styrene µg/m3 0.124
23.8 02/27/2024 00:49TO-15 Tetrahydrofuran µg/m3 0.107
6.48 02/27/2024 00:49TO-15 Toluene µg/m3 0.090
J1.58 02/27/2024 00:49TO-15 Trichlorofluoromethane µg/m3 0.130
4.74 02/27/2024 00:49TO-15 1,2,4-Trimethylbenzene µg/m3 0.110
J1.23 02/27/2024 00:49TO-15 1,3,5-Trimethylbenzene µg/m3 0.236
6.24 02/27/2024 00:49TO-15 o-Xylene µg/m3 0.157
6.63 02/27/2024 00:49TO-15 m,p-Xylene µg/m3 0.217
12.9 02/27/2024 00:49TO-15 Xylene (Total)µg/m3 0.157
V 97581IAS-BKG
B9.14 02/27/2024 01:36TO-15 Acetone µg/m3 0.202
J0.897 02/27/2024 01:36TO-15 Benzene µg/m3 0.073
2.83 02/27/2024 01:36TO-15 Dichlorodifluoromethane µg/m3 0.134
J0.597 02/27/2024 01:36TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
Page 5 of 38
Summary of Detected Analytes
QualifiersAnalyzedUnitsResult
Report Number:
Client Sample ID
Method Parameters
Lab Sample ID
24-053-0009
Report Limit
Project:PDP-001
V 97581IAS-BKG
J0.672 02/27/2024 01:36TO-15 Heptane µg/m3 0.143
J0.676 02/27/2024 01:36TO-15 n-Hexane µg/m3 0.047
JB2.88 02/27/2024 01:36TO-15 Isopropyl Alcohol µg/m3 0.139
3.49 02/27/2024 01:36TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
J1.28 02/27/2024 01:36TO-15 Methylene Chloride µg/m3 0.488
1.66 02/27/2024 01:36TO-15 Tetrahydrofuran µg/m3 0.107
3.52 02/27/2024 01:36TO-15 Toluene µg/m3 0.090
J1.62 02/27/2024 01:36TO-15 Trichlorofluoromethane µg/m3 0.130
J0.408 02/27/2024 01:36TO-15 o-Xylene µg/m3 0.157
J0.864 02/27/2024 01:36TO-15 m,p-Xylene µg/m3 0.217
J1.27 02/27/2024 01:36TO-15 Xylene (Total)µg/m3 0.157
V 97582MP-DUP
67.4 02/26/2024 20:51TO-15 Acetone µg/m3 0.202
2.44 02/26/2024 20:51TO-15 Benzene µg/m3 0.073
J0.737 02/26/2024 20:51TO-15 Carbon Disulfide µg/m3 0.060
J0.517 02/26/2024 20:51TO-15 Chloroform µg/m3 0.086
2.90 02/26/2024 20:51TO-15 Dichlorodifluoromethane µg/m3 0.134
J1.44 02/26/2024 20:51TO-15 Ethylbenzene µg/m3 0.106
J0.408 02/26/2024 20:51TO-15 4-Ethyltoluene µg/m3 0.128
J0.643 02/26/2024 20:51TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
J0.368 02/26/2024 20:51TO-15 Heptane µg/m3 0.143
J1.11 02/26/2024 20:51TO-15 n-Hexane µg/m3 0.047
JB3.52 02/26/2024 20:51TO-15 Isopropyl Alcohol µg/m3 0.139
79.0 02/26/2024 20:51TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
J1.55 02/26/2024 20:51TO-15 Methylene Chloride µg/m3 0.488
J0.560 02/26/2024 20:51TO-15 Naphthalene µg/m3 0.183
4.59 02/26/2024 20:51TO-15 Propene µg/m3 0.242
J0.379 02/26/2024 20:51TO-15 Styrene µg/m3 0.124
63.7 02/26/2024 20:51TO-15 Tetrahydrofuran µg/m3 0.107
3.32 02/26/2024 20:51TO-15 Toluene µg/m3 0.090
J1.74 02/26/2024 20:51TO-15 Trichlorofluoromethane µg/m3 0.130
J1.82 02/26/2024 20:51TO-15 1,2,4-Trimethylbenzene µg/m3 0.110
J0.535 02/26/2024 20:51TO-15 1,3,5-Trimethylbenzene µg/m3 0.236
2.62 02/26/2024 20:51TO-15 o-Xylene µg/m3 0.157
J5.47 02/26/2024 20:51TO-15 m,p-Xylene µg/m3 0.217
J8.09 02/26/2024 20:51TO-15 Xylene (Total)µg/m3 0.157
Page 6 of 38
Summary of Detected Analytes
QualifiersAnalyzedUnitsResult
Report Number:
Client Sample ID
Method Parameters
Lab Sample ID
24-053-0009
Report Limit
Project:PDP-001
V 97583MP-5
66.0 02/26/2024 21:43TO-15 Acetone µg/m3 0.202
2.47 02/26/2024 21:43TO-15 Benzene µg/m3 0.073
J0.747 02/26/2024 21:43TO-15 Carbon Disulfide µg/m3 0.060
J0.522 02/26/2024 21:43TO-15 Chloroform µg/m3 0.086
2.84 02/26/2024 21:43TO-15 Dichlorodifluoromethane µg/m3 0.134
J1.44 02/26/2024 21:43TO-15 Ethylbenzene µg/m3 0.106
J0.408 02/26/2024 21:43TO-15 4-Ethyltoluene µg/m3 0.128
J0.597 02/26/2024 21:43TO-15 1,1,2-Trichloro-1,2,2-trifluoroethane µg/m3 0.561
J0.401 02/26/2024 21:43TO-15 Heptane µg/m3 0.143
J1.42 02/26/2024 21:43TO-15 n-Hexane µg/m3 0.047
JB3.83 02/26/2024 21:43TO-15 Isopropyl Alcohol µg/m3 0.139
76.2 02/26/2024 21:43TO-15 Methyl Ethyl Ketone (MEK)µg/m3 0.224
3.94 02/26/2024 21:43TO-15 Methylene Chloride µg/m3 0.488
J0.492 02/26/2024 21:43TO-15 Naphthalene µg/m3 0.183
4.59 02/26/2024 21:43TO-15 Propene µg/m3 0.242
J0.379 02/26/2024 21:43TO-15 Styrene µg/m3 0.124
63.9 02/26/2024 21:43TO-15 Tetrahydrofuran µg/m3 0.107
3.34 02/26/2024 21:43TO-15 Toluene µg/m3 0.090
J1.80 02/26/2024 21:43TO-15 Trichlorofluoromethane µg/m3 0.130
J1.85 02/26/2024 21:43TO-15 1,2,4-Trimethylbenzene µg/m3 0.110
J0.565 02/26/2024 21:43TO-15 1,3,5-Trimethylbenzene µg/m3 0.236
2.73 02/26/2024 21:43TO-15 o-Xylene µg/m3 0.157
J5.53 02/26/2024 21:43TO-15 m,p-Xylene µg/m3 0.217
J8.26 02/26/2024 21:43TO-15 Xylene (Total)µg/m3 0.157
V 97584MP-3
17400 02/27/2024 15:05TO-15 Acetone µg/m3 40.4
J28.7 02/26/2024 22:19TO-15 Cyclohexane µg/m3 3.22
J55.1 02/26/2024 22:19TO-15 Isopropyl Alcohol µg/m3 2.78
J12.4 02/26/2024 22:19TO-15 Methylene Chloride µg/m3 9.75
14200 02/27/2024 15:05TO-15 Tetrahydrofuran µg/m3 21.4
J7.47 02/26/2024 22:19TO-15 m,p-Xylene µg/m3 4.34
J7.47 02/26/2024 22:19TO-15 Xylene (Total)µg/m3 3.14
Page 7 of 38

Client: Hart & Hickman (Charlotte) CASE NARRATIVE
Project: PDP-001 Lab Report Number: 24-053-0009
Date: 2/28/2024
Volatile Organic Compounds in Air- GC/MS Method TO-15 Sample 97584 (MP-3) QC Batch No: V44133/V44132
The sample was diluted due to the nature of the sample matrix. Reporting limits have been adjusted accordingly.

Page 8 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:IAS-DUP
97578 Matrix:
2/20/2024 0:00
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
114 µg/m3 2.02 47.5Acetone 10 02/28/24 03:02 V44550ENM
2.29 µg/m3 0.073 1.60Benzene 1 02/26/24 23:12 V44517ENM
<0.060 µg/m3 0.060 6.23Carbon Disulfide 1 02/26/24 23:12 V44517ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/26/24 23:12 V44517ENM
<0.086 µg/m3 0.086 2.44Chloroform 1 02/26/24 23:12 V44517ENM
0.949 J µg/m3 0.067 1.03Chloromethane 1 02/26/24 23:12 V44517ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/26/24 23:12 V44517ENM
2.89 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/26/24 23:12 V44517ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/26/24 23:12 V44517ENM
3.20 µg/m3 0.106 2.17Ethylbenzene 1 02/26/24 23:12 V44517ENM
1.93 J µg/m3 0.128 2.464-Ethyltoluene 1 02/26/24 23:12 V44517ENM
0.582 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/26/24 23:12 V44517ENM
2.41 µg/m3 0.143 2.05Heptane 1 02/26/24 23:12 V44517ENM
2.58 µg/m3 0.047 1.76n-Hexane 1 02/26/24 23:12 V44517ENM
6.33 B µg/m3 0.139 4.92Isopropyl Alcohol 1 02/26/24 23:12 V44517ENM
65.8 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/26/24 23:12 V44517ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/26/24 23:12 V44517ENM
1.63 J µg/m3 0.488 1.74Methylene Chloride 1 02/26/24 23:12 V44517ENM
0.560 J µg/m3 0.183 2.62Naphthalene 1 02/26/24 23:12 V44517ENM
<0.242 µg/m3 0.242 0.860Propene 1 02/26/24 23:12 V44517ENM
2.14 µg/m3 0.124 2.13Styrene 1 02/26/24 23:12 V44517ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/26/24 23:12 V44517ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 9 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:IAS-DUP
97578 Matrix:
2/20/2024 0:00
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
25.6 µg/m3 0.107 1.47Tetrahydrofuran 1 02/26/24 23:12 V44517ENM
11.4 µg/m3 0.090 1.88Toluene 1 02/26/24 23:12 V44517ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/26/24 23:12 V44517ENM
1.74 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/26/24 23:12 V44517ENM
10.2 µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/26/24 23:12 V44517ENM
2.77 µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/26/24 23:12 V44517ENM
11.4 µg/m3 0.157 2.17o-Xylene 1 02/26/24 23:12 V44517ENM
12.5 µg/m3 0.217 5.65m,p-Xylene 1 02/26/24 23:12 V44517ENM
23.9 µg/m3 0.157 2.17Xylene (Total)1 02/26/24 23:12 V44517
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/26/24 23:121 ENM V44133
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/26/24 23:121 ENM V44517
Surrogate: 4-Bromofluorobenzene 100 Limits: 70-130%02/28/24 03:0210 ENM V44148
Surrogate: 4-Bromofluorobenzene 100 Limits: 70-130%02/28/24 03:0210 ENM V44550
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 10 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:C-IAS-1
97579 Matrix:
2/20/2024 11:32
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
118 µg/m3 2.02 47.5Acetone 10 02/28/24 03:38 V44550ENM
2.22 µg/m3 0.073 1.60Benzene 1 02/27/24 00:02 V44517ENM
<0.060 µg/m3 0.060 6.23Carbon Disulfide 1 02/27/24 00:02 V44517ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/27/24 00:02 V44517ENM
<0.086 µg/m3 0.086 2.44Chloroform 1 02/27/24 00:02 V44517ENM
0.947 J µg/m3 0.067 1.03Chloromethane 1 02/27/24 00:02 V44517ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/27/24 00:02 V44517ENM
2.87 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/27/24 00:02 V44517ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/27/24 00:02 V44517ENM
3.23 µg/m3 0.106 2.17Ethylbenzene 1 02/27/24 00:02 V44517ENM
1.88 J µg/m3 0.128 2.464-Ethyltoluene 1 02/27/24 00:02 V44517ENM
0.590 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/27/24 00:02 V44517ENM
2.17 µg/m3 0.143 2.05Heptane 1 02/27/24 00:02 V44517ENM
2.51 µg/m3 0.047 1.76n-Hexane 1 02/27/24 00:02 V44517ENM
6.34 B µg/m3 0.139 4.92Isopropyl Alcohol 1 02/27/24 00:02 V44517ENM
65.0 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/27/24 00:02 V44517ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/27/24 00:02 V44517ENM
1.08 J µg/m3 0.488 1.74Methylene Chloride 1 02/27/24 00:02 V44517ENM
0.571 J µg/m3 0.183 2.62Naphthalene 1 02/27/24 00:02 V44517ENM
<0.242 µg/m3 0.242 0.860Propene 1 02/27/24 00:02 V44517ENM
2.11 J µg/m3 0.124 2.13Styrene 1 02/27/24 00:02 V44517ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/27/24 00:02 V44517ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 11 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:C-IAS-1
97579 Matrix:
2/20/2024 11:32
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
25.0 µg/m3 0.107 1.47Tetrahydrofuran 1 02/27/24 00:02 V44517ENM
9.65 µg/m3 0.090 1.88Toluene 1 02/27/24 00:02 V44517ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/27/24 00:02 V44517ENM
1.65 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/27/24 00:02 V44517ENM
10.3 µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/27/24 00:02 V44517ENM
2.69 µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/27/24 00:02 V44517ENM
11.1 µg/m3 0.157 2.17o-Xylene 1 02/27/24 00:02 V44517ENM
12.4 µg/m3 0.217 5.65m,p-Xylene 1 02/27/24 00:02 V44517ENM
23.5 µg/m3 0.157 2.17Xylene (Total)1 02/27/24 00:02 V44517
Surrogate: 4-Bromofluorobenzene 99.7 Limits: 70-130%02/27/24 00:021 ENM V44133
Surrogate: 4-Bromofluorobenzene 99.7 Limits: 70-130%02/27/24 00:021 ENM V44517
Surrogate: 4-Bromofluorobenzene 100 Limits: 70-130%02/28/24 03:3810 ENM V44148
Surrogate: 4-Bromofluorobenzene 100 Limits: 70-130%02/28/24 03:3810 ENM V44550
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 12 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:D-IAS-1
97580 Matrix:
2/20/2024 11:24
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
263 µg/m3 4.04 95.0Acetone 20 02/28/24 04:14 V44550ENM
1.20 J µg/m3 0.073 1.60Benzene 1 02/27/24 00:49 V44517ENM
<0.060 µg/m3 0.060 6.23Carbon Disulfide 1 02/27/24 00:49 V44517ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/27/24 00:49 V44517ENM
<0.086 µg/m3 0.086 2.44Chloroform 1 02/27/24 00:49 V44517ENM
0.972 J µg/m3 0.067 1.03Chloromethane 1 02/27/24 00:49 V44517ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/27/24 00:49 V44517ENM
2.83 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/27/24 00:49 V44517ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/27/24 00:49 V44517ENM
1.81 J µg/m3 0.106 2.17Ethylbenzene 1 02/27/24 00:49 V44517ENM
0.958 J µg/m3 0.128 2.464-Ethyltoluene 1 02/27/24 00:49 V44517ENM
0.590 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/27/24 00:49 V44517ENM
1.31 J µg/m3 0.143 2.05Heptane 1 02/27/24 00:49 V44517ENM
1.32 J µg/m3 0.047 1.76n-Hexane 1 02/27/24 00:49 V44517ENM
9.13 B µg/m3 0.139 4.92Isopropyl Alcohol 1 02/27/24 00:49 V44517ENM
59.3 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/27/24 00:49 V44517ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/27/24 00:49 V44517ENM
1.47 J µg/m3 0.488 1.74Methylene Chloride 1 02/27/24 00:49 V44517ENM
<0.183 µg/m3 0.183 2.62Naphthalene 1 02/27/24 00:49 V44517ENM
<0.242 µg/m3 0.242 0.860Propene 1 02/27/24 00:49 V44517ENM
1.63 J µg/m3 0.124 2.13Styrene 1 02/27/24 00:49 V44517ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/27/24 00:49 V44517ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 13 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:D-IAS-1
97580 Matrix:
2/20/2024 11:24
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00 V44549 02/27/24 09:00
23.8 µg/m3 0.107 1.47Tetrahydrofuran 1 02/27/24 00:49 V44517ENM
6.48 µg/m3 0.090 1.88Toluene 1 02/27/24 00:49 V44517ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/27/24 00:49 V44517ENM
1.58 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/27/24 00:49 V44517ENM
4.74 µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/27/24 00:49 V44517ENM
1.23 J µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/27/24 00:49 V44517ENM
6.24 µg/m3 0.157 2.17o-Xylene 1 02/27/24 00:49 V44517ENM
6.63 µg/m3 0.217 5.65m,p-Xylene 1 02/27/24 00:49 V44517ENM
12.9 µg/m3 0.157 2.17Xylene (Total)1 02/27/24 00:49 V44517
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/27/24 00:491 ENM V44133
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/27/24 00:491 ENM V44517
Surrogate: 4-Bromofluorobenzene 98.3 Limits: 70-130%02/28/24 04:1420 ENM V44148
Surrogate: 4-Bromofluorobenzene 98.3 Limits: 70-130%02/28/24 04:1420 ENM V44550
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 14 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:IAS-BKG
97581 Matrix:
2/20/2024 11:23
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00
9.14 B µg/m3 0.202 4.75Acetone 1 02/27/24 01:36 V44517ENM
0.897 J µg/m3 0.073 1.60Benzene 1 02/27/24 01:36 V44517ENM
<0.060 µg/m3 0.060 6.23Carbon Disulfide 1 02/27/24 01:36 V44517ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/27/24 01:36 V44517ENM
<0.086 µg/m3 0.086 2.44Chloroform 1 02/27/24 01:36 V44517ENM
<0.067 µg/m3 0.067 1.03Chloromethane 1 02/27/24 01:36 V44517ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/27/24 01:36 V44517ENM
2.83 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/27/24 01:36 V44517ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/27/24 01:36 V44517ENM
<0.106 µg/m3 0.106 2.17Ethylbenzene 1 02/27/24 01:36 V44517ENM
<0.128 µg/m3 0.128 2.464-Ethyltoluene 1 02/27/24 01:36 V44517ENM
0.597 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/27/24 01:36 V44517ENM
0.672 J µg/m3 0.143 2.05Heptane 1 02/27/24 01:36 V44517ENM
0.676 J µg/m3 0.047 1.76n-Hexane 1 02/27/24 01:36 V44517ENM
2.88 JB µg/m3 0.139 4.92Isopropyl Alcohol 1 02/27/24 01:36 V44517ENM
3.49 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/27/24 01:36 V44517ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/27/24 01:36 V44517ENM
1.28 J µg/m3 0.488 1.74Methylene Chloride 1 02/27/24 01:36 V44517ENM
<0.183 µg/m3 0.183 2.62Naphthalene 1 02/27/24 01:36 V44517ENM
<0.242 µg/m3 0.242 0.860Propene 1 02/27/24 01:36 V44517ENM
<0.124 µg/m3 0.124 2.13Styrene 1 02/27/24 01:36 V44517ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/27/24 01:36 V44517ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 15 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:IAS-BKG
97581 Matrix:
2/20/2024 11:23
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44513 02/29/24 09:00
1.66 µg/m3 0.107 1.47Tetrahydrofuran 1 02/27/24 01:36 V44517ENM
3.52 µg/m3 0.090 1.88Toluene 1 02/27/24 01:36 V44517ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/27/24 01:36 V44517ENM
1.62 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/27/24 01:36 V44517ENM
<0.110 µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/27/24 01:36 V44517ENM
<0.236 µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/27/24 01:36 V44517ENM
0.408 J µg/m3 0.157 2.17o-Xylene 1 02/27/24 01:36 V44517ENM
0.864 J µg/m3 0.217 5.65m,p-Xylene 1 02/27/24 01:36 V44517ENM
1.27 J µg/m3 0.157 2.17Xylene (Total)1 02/27/24 01:36 V44517
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/27/24 01:361 ENM V44133
Surrogate: 4-Bromofluorobenzene 101 Limits: 70-130%02/27/24 01:361 ENM V44517
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 16 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-DUP
97582 Matrix:
2/21/2024 0:00
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
67.4 µg/m3 0.202 4.75Acetone 1 02/26/24 20:51 V44133ENM
2.44 µg/m3 0.073 1.60Benzene 1 02/26/24 20:51 V44133ENM
<0.147 µg/m3 0.147 10.4Benzyl Chloride 1 02/26/24 20:51 V44133ENM
<0.150 µg/m3 0.150 3.35Bromodichloromethane 1 02/26/24 20:51 V44133ENM
<0.153 µg/m3 0.153 5.17Bromoform 1 02/26/24 20:51 V44133ENM
<0.115 µg/m3 0.115 1.94Bromomethane 1 02/26/24 20:51 V44133ENM
<0.328 µg/m3 0.328 1.111,3-Butadiene 1 02/26/24 20:51 V44133ENM
0.737 J µg/m3 0.060 6.23Carbon Disulfide 1 02/26/24 20:51 V44133ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/26/24 20:51 V44133ENM
<0.107 µg/m3 0.107 2.30Chlorobenzene 1 02/26/24 20:51 V44133ENM
<0.208 µg/m3 0.208 4.26Chlorodibromomethane 1 02/26/24 20:51 V44133ENM
<0.164 µg/m3 0.164 1.32Chloroethane 1 02/26/24 20:51 V44133ENM
0.517 J µg/m3 0.086 2.44Chloroform 1 02/26/24 20:51 V44133ENM
<0.067 µg/m3 0.067 1.03Chloromethane 1 02/26/24 20:51 V44133ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/26/24 20:51 V44133ENM
<0.151 µg/m3 0.151 3.841,2-Dibromoethane 1 02/26/24 20:51 V44133ENM
<0.096 µg/m3 0.096 3.011,2-Dichlorobenzene 1 02/26/24 20:51 V44133ENM
<0.174 µg/m3 0.174 12.01,3-Dichlorobenzene 1 02/26/24 20:51 V44133ENM
<0.186 µg/m3 0.186 3.011,4-Dichlorobenzene 1 02/26/24 20:51 V44133ENM
2.90 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/26/24 20:51 V44133ENM
<0.101 µg/m3 0.101 2.021,1-Dichloroethane 1 02/26/24 20:51 V44133ENM
<0.129 µg/m3 0.129 2.021,2-Dichloroethane 1 02/26/24 20:51 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 17 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-DUP
97582 Matrix:
2/21/2024 0:00
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
<0.107 µg/m3 0.107 1.981,1-Dichloroethene 1 02/26/24 20:51 V44133ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/26/24 20:51 V44133ENM
<0.108 µg/m3 0.108 1.98trans-1,2-Dichloroethene 1 02/26/24 20:51 V44133ENM
<0.205 µg/m3 0.205 2.311,2-Dichloropropane 1 02/26/24 20:51 V44133ENM
<0.622 µg/m3 0.622 3.501,2-Dichlorotetrafluoroethane 1 02/26/24 20:51 V44133ENM
<0.178 µg/m3 0.178 2.27cis-1,3-Dichloropropene 1 02/26/24 20:51 V44133ENM
<0.178 µg/m3 0.178 2.27trans-1,3-Dichloropropene 1 02/26/24 20:51 V44133ENM
<0.435 µg/m3 0.435 1.801,4-Dioxane 1 02/26/24 20:51 V44133ENM
<0.136 µg/m3 0.136 1.80Ethyl Acetate 1 02/26/24 20:51 V44133ENM
1.44 J µg/m3 0.106 2.17Ethylbenzene 1 02/26/24 20:51 V44133ENM
0.408 J µg/m3 0.128 2.464-Ethyltoluene 1 02/26/24 20:51 V44133ENM
0.643 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/26/24 20:51 V44133ENM
0.368 J µg/m3 0.143 2.05Heptane 1 02/26/24 20:51 V44133ENM
<0.330 µg/m3 0.330 5.33Hexachlorobutadiene 1 02/26/24 20:51 V44133ENM
1.11 J µg/m3 0.047 1.76n-Hexane 1 02/26/24 20:51 V44133ENM
<0.285 µg/m3 0.285 2.052-Hexanone 1 02/26/24 20:51 V44133ENM
3.52 JB µg/m3 0.139 4.92Isopropyl Alcohol 1 02/26/24 20:51 V44133ENM
79.0 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/26/24 20:51 V44133ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/26/24 20:51 V44133ENM
<0.121 µg/m3 0.121 2.054-Methyl-2-Pentanone 1 02/26/24 20:51 V44133ENM
1.55 J µg/m3 0.488 1.74Methylene Chloride 1 02/26/24 20:51 V44133ENM
0.560 J µg/m3 0.183 2.62Naphthalene 1 02/26/24 20:51 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 18 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-DUP
97582 Matrix:
2/21/2024 0:00
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
4.59 µg/m3 0.242 0.860Propene 1 02/26/24 20:51 V44133ENM
0.379 J µg/m3 0.124 2.13Styrene 1 02/26/24 20:51 V44133ENM
<0.104 µg/m3 0.104 3.431,1,2,2-Tetrachloroethane 1 02/26/24 20:51 V44133ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/26/24 20:51 V44133ENM
63.7 µg/m3 0.107 1.47Tetrahydrofuran 1 02/26/24 20:51 V44133ENM
3.32 µg/m3 0.090 1.88Toluene 1 02/26/24 20:51 V44133ENM
<0.209 µg/m3 0.209 3.711,2,4-Trichlorobenzene 1 02/26/24 20:51 V44133ENM
<0.144 µg/m3 0.144 2.731,1,1-Trichloroethane 1 02/26/24 20:51 V44133ENM
<0.087 µg/m3 0.087 2.731,1,2-Trichloroethane 1 02/26/24 20:51 V44133ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/26/24 20:51 V44133ENM
1.74 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/26/24 20:51 V44133ENM
1.82 J µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/26/24 20:51 V44133ENM
0.535 J µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/26/24 20:51 V44133ENM
<0.224 µg/m3 0.224 1.76Vinyl Acetate 1 02/26/24 20:51 V44133ENM
<0.127 µg/m3 0.127 1.28Vinyl Chloride 1 02/26/24 20:51 V44133ENM
2.62 µg/m3 0.157 2.17o-Xylene 1 02/26/24 20:51 V44133ENM
5.47 J µg/m3 0.217 5.65m,p-Xylene 1 02/26/24 20:51 V44133ENM
8.09 J µg/m3 0.157 2.17Xylene (Total)1 02/26/24 20:51 V44133
Surrogate: 4-Bromofluorobenzene 98.9 Limits: 70-130%02/26/24 20:511 ENM V44133
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 19 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-5
97583 Matrix:
2/21/2024 15:57
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
66.0 µg/m3 0.202 4.75Acetone 1 02/26/24 21:43 V44133ENM
2.47 µg/m3 0.073 1.60Benzene 1 02/26/24 21:43 V44133ENM
<0.147 µg/m3 0.147 10.4Benzyl Chloride 1 02/26/24 21:43 V44133ENM
<0.150 µg/m3 0.150 3.35Bromodichloromethane 1 02/26/24 21:43 V44133ENM
<0.153 µg/m3 0.153 5.17Bromoform 1 02/26/24 21:43 V44133ENM
<0.115 µg/m3 0.115 1.94Bromomethane 1 02/26/24 21:43 V44133ENM
<0.328 µg/m3 0.328 1.111,3-Butadiene 1 02/26/24 21:43 V44133ENM
0.747 J µg/m3 0.060 6.23Carbon Disulfide 1 02/26/24 21:43 V44133ENM
<0.155 µg/m3 0.155 3.15Carbon Tetrachloride 1 02/26/24 21:43 V44133ENM
<0.107 µg/m3 0.107 2.30Chlorobenzene 1 02/26/24 21:43 V44133ENM
<0.208 µg/m3 0.208 4.26Chlorodibromomethane 1 02/26/24 21:43 V44133ENM
<0.164 µg/m3 0.164 1.32Chloroethane 1 02/26/24 21:43 V44133ENM
0.522 J µg/m3 0.086 2.44Chloroform 1 02/26/24 21:43 V44133ENM
<0.067 µg/m3 0.067 1.03Chloromethane 1 02/26/24 21:43 V44133ENM
<0.161 µg/m3 0.161 3.44Cyclohexane 1 02/26/24 21:43 V44133ENM
<0.151 µg/m3 0.151 3.841,2-Dibromoethane 1 02/26/24 21:43 V44133ENM
<0.096 µg/m3 0.096 3.011,2-Dichlorobenzene 1 02/26/24 21:43 V44133ENM
<0.174 µg/m3 0.174 12.01,3-Dichlorobenzene 1 02/26/24 21:43 V44133ENM
<0.186 µg/m3 0.186 3.011,4-Dichlorobenzene 1 02/26/24 21:43 V44133ENM
2.84 µg/m3 0.134 2.47Dichlorodifluoromethane 1 02/26/24 21:43 V44133ENM
<0.101 µg/m3 0.101 2.021,1-Dichloroethane 1 02/26/24 21:43 V44133ENM
<0.129 µg/m3 0.129 2.021,2-Dichloroethane 1 02/26/24 21:43 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 20 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-5
97583 Matrix:
2/21/2024 15:57
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
<0.107 µg/m3 0.107 1.981,1-Dichloroethene 1 02/26/24 21:43 V44133ENM
<0.095 µg/m3 0.095 1.98cis-1,2-Dichloroethene 1 02/26/24 21:43 V44133ENM
<0.108 µg/m3 0.108 1.98trans-1,2-Dichloroethene 1 02/26/24 21:43 V44133ENM
<0.205 µg/m3 0.205 2.311,2-Dichloropropane 1 02/26/24 21:43 V44133ENM
<0.622 µg/m3 0.622 3.501,2-Dichlorotetrafluoroethane 1 02/26/24 21:43 V44133ENM
<0.178 µg/m3 0.178 2.27cis-1,3-Dichloropropene 1 02/26/24 21:43 V44133ENM
<0.178 µg/m3 0.178 2.27trans-1,3-Dichloropropene 1 02/26/24 21:43 V44133ENM
<0.435 µg/m3 0.435 1.801,4-Dioxane 1 02/26/24 21:43 V44133ENM
<0.136 µg/m3 0.136 1.80Ethyl Acetate 1 02/26/24 21:43 V44133ENM
1.44 J µg/m3 0.106 2.17Ethylbenzene 1 02/26/24 21:43 V44133ENM
0.408 J µg/m3 0.128 2.464-Ethyltoluene 1 02/26/24 21:43 V44133ENM
0.597 J µg/m3 0.561 3.831,1,2-Trichloro-1,2,2-trifluoroethane 1 02/26/24 21:43 V44133ENM
0.401 J µg/m3 0.143 2.05Heptane 1 02/26/24 21:43 V44133ENM
<0.330 µg/m3 0.330 5.33Hexachlorobutadiene 1 02/26/24 21:43 V44133ENM
1.42 J µg/m3 0.047 1.76n-Hexane 1 02/26/24 21:43 V44133ENM
<0.285 µg/m3 0.285 2.052-Hexanone 1 02/26/24 21:43 V44133ENM
3.83 JB µg/m3 0.139 4.92Isopropyl Alcohol 1 02/26/24 21:43 V44133ENM
76.2 µg/m3 0.224 1.47Methyl Ethyl Ketone (MEK)1 02/26/24 21:43 V44133ENM
<0.033 µg/m3 0.033 1.80Methyl tert-butyl ether (MTBE)1 02/26/24 21:43 V44133ENM
<0.121 µg/m3 0.121 2.054-Methyl-2-Pentanone 1 02/26/24 21:43 V44133ENM
3.94 µg/m3 0.488 1.74Methylene Chloride 1 02/26/24 21:43 V44133ENM
0.492 J µg/m3 0.183 2.62Naphthalene 1 02/26/24 21:43 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 21 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-5
97583 Matrix:
2/21/2024 15:57
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00
4.59 µg/m3 0.242 0.860Propene 1 02/26/24 21:43 V44133ENM
0.379 J µg/m3 0.124 2.13Styrene 1 02/26/24 21:43 V44133ENM
<0.104 µg/m3 0.104 3.431,1,2,2-Tetrachloroethane 1 02/26/24 21:43 V44133ENM
<0.181 µg/m3 0.181 3.39Tetrachloroethene 1 02/26/24 21:43 V44133ENM
63.9 µg/m3 0.107 1.47Tetrahydrofuran 1 02/26/24 21:43 V44133ENM
3.34 µg/m3 0.090 1.88Toluene 1 02/26/24 21:43 V44133ENM
<0.209 µg/m3 0.209 3.711,2,4-Trichlorobenzene 1 02/26/24 21:43 V44133ENM
<0.144 µg/m3 0.144 2.731,1,1-Trichloroethane 1 02/26/24 21:43 V44133ENM
<0.087 µg/m3 0.087 2.731,1,2-Trichloroethane 1 02/26/24 21:43 V44133ENM
<0.199 µg/m3 0.199 2.15Trichloroethene 1 02/26/24 21:43 V44133ENM
1.80 J µg/m3 0.130 2.81Trichlorofluoromethane 1 02/26/24 21:43 V44133ENM
1.85 J µg/m3 0.110 2.461,2,4-Trimethylbenzene 1 02/26/24 21:43 V44133ENM
0.565 J µg/m3 0.236 2.461,3,5-Trimethylbenzene 1 02/26/24 21:43 V44133ENM
<0.224 µg/m3 0.224 1.76Vinyl Acetate 1 02/26/24 21:43 V44133ENM
<0.127 µg/m3 0.127 1.28Vinyl Chloride 1 02/26/24 21:43 V44133ENM
2.73 µg/m3 0.157 2.17o-Xylene 1 02/26/24 21:43 V44133ENM
5.53 J µg/m3 0.217 5.65m,p-Xylene 1 02/26/24 21:43 V44133ENM
8.26 J µg/m3 0.157 2.17Xylene (Total)1 02/26/24 21:43 V44133
Surrogate: 4-Bromofluorobenzene 98.9 Limits: 70-130%02/26/24 21:431 ENM V44133
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 22 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-3
97584 Matrix:
2/21/2024 11:50
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00 V44146 02/27/24 09:00
17400 µg/m3 40.4 950Acetone 200 02/27/24 15:05 V44148ENM
<1.46 µg/m3 1.46 31.9Benzene 20 02/26/24 22:19 V44133ENM
<2.94 µg/m3 2.94 207Benzyl Chloride 20 02/26/24 22:19 V44133ENM
<3.00 µg/m3 3.00 67.0Bromodichloromethane 20 02/26/24 22:19 V44133ENM
<3.05 µg/m3 3.05 103Bromoform 20 02/26/24 22:19 V44133ENM
<2.30 µg/m3 2.30 38.8Bromomethane 20 02/26/24 22:19 V44133ENM
<6.53 µg/m3 6.53 22.11,3-Butadiene 20 02/26/24 22:19 V44133ENM
<1.22 µg/m3 1.22 125Carbon Disulfide 20 02/26/24 22:19 V44133ENM
<3.10 µg/m3 3.10 62.9Carbon Tetrachloride 20 02/26/24 22:19 V44133ENM
<2.14 µg/m3 2.14 46.0Chlorobenzene 20 02/26/24 22:19 V44133ENM
<4.16 µg/m3 4.16 85.2Chlorodibromomethane 20 02/26/24 22:19 V44133ENM
<3.28 µg/m3 3.28 26.4Chloroethane 20 02/26/24 22:19 V44133ENM
<1.73 µg/m3 1.73 48.8Chloroform 20 02/26/24 22:19 V44133ENM
<1.34 µg/m3 1.34 20.6Chloromethane 20 02/26/24 22:19 V44133ENM
28.7 J µg/m3 3.22 68.8Cyclohexane 20 02/26/24 22:19 V44133ENM
<3.02 µg/m3 3.02 76.81,2-Dibromoethane 20 02/26/24 22:19 V44133ENM
<1.92 µg/m3 1.92 60.11,2-Dichlorobenzene 20 02/26/24 22:19 V44133ENM
<3.48 µg/m3 3.48 2411,3-Dichlorobenzene 20 02/26/24 22:19 V44133ENM
<3.72 µg/m3 3.72 60.11,4-Dichlorobenzene 20 02/26/24 22:19 V44133ENM
<2.68 µg/m3 2.68 49.4Dichlorodifluoromethane 20 02/26/24 22:19 V44133ENM
<2.02 µg/m3 2.02 40.51,1-Dichloroethane 20 02/26/24 22:19 V44133ENM
<2.58 µg/m3 2.58 40.51,2-Dichloroethane 20 02/26/24 22:19 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 23 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-3
97584 Matrix:
2/21/2024 11:50
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00 V44146 02/27/24 09:00
<2.14 µg/m3 2.14 39.61,1-Dichloroethene 20 02/26/24 22:19 V44133ENM
<1.91 µg/m3 1.91 39.6cis-1,2-Dichloroethene 20 02/26/24 22:19 V44133ENM
<2.16 µg/m3 2.16 39.6trans-1,2-Dichloroethene 20 02/26/24 22:19 V44133ENM
<4.10 µg/m3 4.10 46.21,2-Dichloropropane 20 02/26/24 22:19 V44133ENM
<12.4 µg/m3 12.4 69.91,2-Dichlorotetrafluoroethane 20 02/26/24 22:19 V44133ENM
<3.56 µg/m3 3.56 45.4cis-1,3-Dichloropropene 20 02/26/24 22:19 V44133ENM
<3.56 µg/m3 3.56 45.4trans-1,3-Dichloropropene 20 02/26/24 22:19 V44133ENM
<8.69 µg/m3 8.69 36.01,4-Dioxane 20 02/26/24 22:19 V44133ENM
<2.72 µg/m3 2.72 36.0Ethyl Acetate 20 02/26/24 22:19 V44133ENM
<2.12 µg/m3 2.12 43.4Ethylbenzene 20 02/26/24 22:19 V44133ENM
<2.56 µg/m3 2.56 49.24-Ethyltoluene 20 02/26/24 22:19 V44133ENM
<11.2 µg/m3 11.2 76.61,1,2-Trichloro-1,2,2-trifluoroethane 20 02/26/24 22:19 V44133ENM
<2.86 µg/m3 2.86 41.0Heptane 20 02/26/24 22:19 V44133ENM
<6.62 µg/m3 6.62 107Hexachlorobutadiene 20 02/26/24 22:19 V44133ENM
<0.942 µg/m3 0.942 35.2n-Hexane 20 02/26/24 22:19 V44133ENM
<5.71 µg/m3 5.71 41.02-Hexanone 20 02/26/24 22:19 V44133ENM
55.1 J µg/m3 2.78 98.3Isopropyl Alcohol 20 02/26/24 22:19 V44133ENM
<4.48 µg/m3 4.48 29.5Methyl Ethyl Ketone (MEK)20 02/26/24 22:19 V44133ENM
<0.672 µg/m3 0.672 36.1Methyl tert-butyl ether (MTBE)20 02/26/24 22:19 V44133ENM
<2.42 µg/m3 2.42 41.04-Methyl-2-Pentanone 20 02/26/24 22:19 V44133ENM
12.4 J µg/m3 9.75 34.7Methylene Chloride 20 02/26/24 22:19 V44133ENM
<3.66 µg/m3 3.66 52.4Naphthalene 20 02/26/24 22:19 V44133ENM
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 24 of 38
,
REPORT OF ANALYSISReport Number :
Project
Information :
NC 28203
24-053-0009
01102
Hart & Hickman (Charlotte)
2923 South Tryon St. Ste 100
David Kahn
Charlotte
Received : 02/22/2024
PDP-001
Report Date : 03/08/2024
Sample ID :
Lab No :
Sampled:MP-3
97584 Matrix:
2/21/2024 11:50
Air
Analytical Method:
Prep Method:
Test Results Units MDL MQL By Analytical
Batch
Date / Time
Analyzed
DF
TO-15 Prep
TO-15 Prep Batch(es):V44132 02/26/24 09:00 V44146 02/27/24 09:00
<4.84 µg/m3 4.84 17.2Propene 20 02/26/24 22:19 V44133ENM
<2.48 µg/m3 2.48 42.6Styrene 20 02/26/24 22:19 V44133ENM
<2.08 µg/m3 2.08 68.61,1,2,2-Tetrachloroethane 20 02/26/24 22:19 V44133ENM
<3.62 µg/m3 3.62 67.8Tetrachloroethene 20 02/26/24 22:19 V44133ENM
14200 µg/m3 21.4 295Tetrahydrofuran 200 02/27/24 15:05 V44148ENM
<1.80 µg/m3 1.80 37.7Toluene 20 02/26/24 22:19 V44133ENM
<4.18 µg/m3 4.18 74.21,2,4-Trichlorobenzene 20 02/26/24 22:19 V44133ENM
<2.88 µg/m3 2.88 54.61,1,1-Trichloroethane 20 02/26/24 22:19 V44133ENM
<1.75 µg/m3 1.75 54.61,1,2-Trichloroethane 20 02/26/24 22:19 V44133ENM
<3.98 µg/m3 3.98 43.0Trichloroethene 20 02/26/24 22:19 V44133ENM
<2.60 µg/m3 2.60 56.2Trichlorofluoromethane 20 02/26/24 22:19 V44133ENM
<2.20 µg/m3 2.20 49.21,2,4-Trimethylbenzene 20 02/26/24 22:19 V44133ENM
<4.72 µg/m3 4.72 49.21,3,5-Trimethylbenzene 20 02/26/24 22:19 V44133ENM
<4.48 µg/m3 4.48 35.2Vinyl Acetate 20 02/26/24 22:19 V44133ENM
<2.54 µg/m3 2.54 25.6Vinyl Chloride 20 02/26/24 22:19 V44133ENM
<3.14 µg/m3 3.14 43.4o-Xylene 20 02/26/24 22:19 V44133ENM
7.47 J µg/m3 4.34 113m,p-Xylene 20 02/26/24 22:19 V44133ENM
7.47 J µg/m3 3.14 43.4Xylene (Total)20 02/26/24 22:19 V44133
Surrogate: 4-Bromofluorobenzene 102 Limits: 70-130%02/26/24 22:1920 ENM V44133
Surrogate: 4-Bromofluorobenzene 100 Limits: 70-130%02/27/24 15:05200 ENM V44148
Qualifiers/
Definitions
Dilution FactorDFAnalyte detected in blankB
Method Quantitation LimitMQLEstimated valueJ
Page 25 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44133QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44132
Associated Lab Samples: 97582, 97583, 97584
LRB-V44132 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/26/24 13:174.750.2021.05µg/m3Acetone
02/26/24 13:171.600.073<0.073µg/m3Benzene
02/26/24 13:1710.40.147<0.147µg/m3Benzyl Chloride
02/26/24 13:173.350.150<0.150µg/m3Bromodichloromethane
02/26/24 13:175.170.153<0.153µg/m3Bromoform
02/26/24 13:171.940.115<0.115µg/m3Bromomethane
02/26/24 13:171.110.328<0.328µg/m31,3-Butadiene
02/26/24 13:176.230.060<0.060µg/m3Carbon Disulfide
02/26/24 13:173.150.155<0.155µg/m3Carbon Tetrachloride
02/26/24 13:172.300.107<0.107µg/m3Chlorobenzene
02/26/24 13:174.260.208<0.208µg/m3Chlorodibromomethane
02/26/24 13:171.320.164<0.164µg/m3Chloroethane
02/26/24 13:172.440.086<0.086µg/m3Chloroform
02/26/24 13:171.030.067<0.067µg/m3Chloromethane
02/26/24 13:173.440.161<0.161µg/m3Cyclohexane
02/26/24 13:173.840.151<0.151µg/m31,2-Dibromoethane
02/26/24 13:173.010.096<0.096µg/m31,2-Dichlorobenzene
02/26/24 13:1712.00.174<0.174µg/m31,3-Dichlorobenzene
02/26/24 13:173.010.186<0.186µg/m31,4-Dichlorobenzene
02/26/24 13:172.470.134<0.134µg/m3Dichlorodifluoromethane
02/26/24 13:172.020.101<0.101µg/m31,1-Dichloroethane
02/26/24 13:172.020.129<0.129µg/m31,2-Dichloroethane
02/26/24 13:171.980.107<0.107µg/m31,1-Dichloroethene
02/26/24 13:171.980.095<0.095µg/m3cis-1,2-Dichloroethene
02/26/24 13:171.980.108<0.108µg/m3trans-1,2-Dichloroethene
02/26/24 13:172.310.205<0.205µg/m31,2-Dichloropropane
02/26/24 13:173.500.622<0.622µg/m31,2-Dichlorotetrafluoroethane
Page 1 of 10Date:03/08/2024 10:03 AM
Page 26 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44133QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44132
Associated Lab Samples: 97582, 97583, 97584
LRB-V44132 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/26/24 13:172.270.178<0.178µg/m3cis-1,3-Dichloropropene
02/26/24 13:172.270.178<0.178µg/m3trans-1,3-Dichloropropene
02/26/24 13:171.800.435<0.435µg/m31,4-Dioxane
02/26/24 13:171.800.136<0.136µg/m3Ethyl Acetate
02/26/24 13:172.170.106<0.106µg/m3Ethylbenzene
02/26/24 13:172.460.128<0.128µg/m34-Ethyltoluene
02/26/24 13:173.830.561<0.561µg/m31,1,2-Trichloro-1,2,2-trifluoroethane
02/26/24 13:172.050.143<0.143µg/m3Heptane
02/26/24 13:175.330.330<0.330µg/m3Hexachlorobutadiene
02/26/24 13:171.760.047<0.047µg/m3n-Hexane
02/26/24 13:172.050.285<0.285µg/m32-Hexanone
02/26/24 13:174.920.1391.54µg/m3Isopropyl Alcohol
02/26/24 13:171.470.224<0.224µg/m3Methyl Ethyl Ketone (MEK)
02/26/24 13:171.800.033<0.033µg/m3Methyl tert-butyl ether (MTBE)
02/26/24 13:172.050.121<0.121µg/m34-Methyl-2-Pentanone
02/26/24 13:171.740.488<0.488µg/m3Methylene Chloride
02/26/24 13:172.620.183<0.183µg/m3Naphthalene
02/26/24 13:170.8600.242<0.242µg/m3Propene
02/26/24 13:172.130.124<0.124µg/m3Styrene
02/26/24 13:173.430.104<0.104µg/m31,1,2,2-Tetrachloroethane
02/26/24 13:173.390.181<0.181µg/m3Tetrachloroethene
02/26/24 13:171.470.107<0.107µg/m3Tetrahydrofuran
02/26/24 13:171.880.090<0.090µg/m3Toluene
02/26/24 13:173.710.209<0.209µg/m31,2,4-Trichlorobenzene
02/26/24 13:172.730.144<0.144µg/m31,1,1-Trichloroethane
02/26/24 13:172.730.087<0.087µg/m31,1,2-Trichloroethane
02/26/24 13:172.150.199<0.199µg/m3Trichloroethene
Page 2 of 10Date:03/08/2024 10:03 AM
Page 27 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44133QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44132
Associated Lab Samples: 97582, 97583, 97584
LRB-V44132 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/26/24 13:172.810.130<0.130µg/m3Trichlorofluoromethane
02/26/24 13:172.460.110<0.110µg/m31,2,4-Trimethylbenzene
02/26/24 13:172.460.236<0.236µg/m31,3,5-Trimethylbenzene
02/26/24 13:171.760.224<0.224µg/m3Vinyl Acetate
02/26/24 13:171.280.127<0.127µg/m3Vinyl Chloride
02/26/24 13:172.170.157<0.157µg/m3o-Xylene
02/26/24 13:175.650.217<0.217µg/m3m,p-Xylene
02/26/24 13:174-Bromofluorobenzene (S)94.1 70-130
LCS-V44132Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
93.211.111.9µg/m3Acetone 70-130
88.114.116.0µg/m3Benzene 70-130
98.025.425.9µg/m3Benzyl Chloride 70-130
87.729.433.5µg/m3Bromodichloromethane 70-130
93.848.551.7µg/m3Bromoform 70-130
95.318.519.4µg/m3Bromomethane 70-130
95.410.611.1µg/m31,3-Butadiene 70-130
97.415.215.6µg/m3Carbon Disulfide 70-130
87.627.631.5µg/m3Carbon Tetrachloride 70-130
95.622.023.0µg/m3Chlorobenzene 70-130
93.139.742.6µg/m3Chlorodibromomethane 70-130
93.912.413.2µg/m3Chloroethane 70-130
90.922.224.4µg/m3Chloroform 70-130
10310.610.3µg/m3Chloromethane 70-130
88.915.317.2µg/m3Cyclohexane 70-130
Page 3 of 10Date:03/08/2024 10:03 AM
Page 28 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44133QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44132
LCS-V44132Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
95.536.738.4µg/m31,2-Dibromoethane 70-130
10130.530.1µg/m31,2-Dichlorobenzene 70-130
10030.130.1µg/m31,3-Dichlorobenzene 70-130
10130.330.1µg/m31,4-Dichlorobenzene 70-130
93.923.224.7µg/m3Dichlorodifluoromethane 70-130
98.519.920.2µg/m31,1-Dichloroethane 70-130
89.118.020.2µg/m31,2-Dichloroethane 70-130
98.419.519.8µg/m31,1-Dichloroethene 70-130
96.919.219.8µg/m3cis-1,2-Dichloroethene 70-130
98.419.519.8µg/m3trans-1,2-Dichloroethene 70-130
88.720.523.1µg/m31,2-Dichloropropane 70-130
95.433.435.0µg/m31,2-Dichlorotetrafluoroethane 70-130
86.719.722.7µg/m3cis-1,3-Dichloropropene 70-130
85.919.522.7µg/m3trans-1,3-Dichloropropene 70-130
85.515.418.0µg/m31,4-Dioxane 70-130
92.716.718.0µg/m3Ethyl Acetate 70-130
94.420.521.7µg/m3Ethylbenzene 70-130
96.323.724.6µg/m34-Ethyltoluene 70-130
97.637.438.3µg/m31,1,2-Trichloro-1,2,2-trifluoroethane 70-130
90.218.520.5µg/m3Heptane 70-130
91.148.653.3µg/m3Hexachlorobutadiene 70-130
97.717.217.6µg/m3n-Hexane 70-130
93.119.120.5µg/m32-Hexanone 70-130
95.111.712.3µg/m3Isopropyl Alcohol 70-130
93.913.914.8µg/m3Methyl Ethyl Ketone (MEK)70-130
94.417.018.0µg/m3Methyl tert-butyl ether (MTBE)70-130
87.818.020.5µg/m34-Methyl-2-Pentanone 70-130
Page 4 of 10Date:03/08/2024 10:03 AM
Page 29 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44133QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44132
LCS-V44132Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
89.615.617.4µg/m3Methylene Chloride 70-130
10226.726.2µg/m3Naphthalene 70-130
93.38.048.61µg/m3Propene 70-130
92.419.721.3µg/m3Styrene 70-130
94.732.534.3µg/m31,1,2,2-Tetrachloroethane 70-130
89.330.333.9µg/m3Tetrachloroethene 70-130
89.713.214.7µg/m3Tetrahydrofuran 70-130
88.216.618.8µg/m3Toluene 70-130
97.536.237.1µg/m31,2,4-Trichlorobenzene 70-130
88.224.127.3µg/m31,1,1-Trichloroethane 70-130
93.425.527.3µg/m31,1,2-Trichloroethane 70-130
91.024.526.9µg/m3Trichloroethene 70-130
98.227.628.1µg/m3Trichlorofluoromethane 70-130
10124.824.6µg/m31,2,4-Trimethylbenzene 70-130
10225.024.6µg/m31,3,5-Trimethylbenzene 70-130
92.616.317.6µg/m3Vinyl Acetate 70-130
96.012.312.8µg/m3Vinyl Chloride 70-130
96.320.921.7µg/m3o-Xylene 70-130
96.742.043.4µg/m3m,p-Xylene 70-130
1014-Bromofluorobenzene (S)70-130
Page 5 of 10Date:03/08/2024 10:03 AM
Page 30 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44148QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44146
Associated Lab Samples: 97584
LRB-V44146 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/27/24 14:294.750.2021.04µg/m3Acetone
02/27/24 14:291.470.107<0.107µg/m3Tetrahydrofuran
02/27/24 14:294-Bromofluorobenzene (S)98.3 70-130
LCS-V44146Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
94.911.311.9µg/m3Acetone 70-130
91.113.414.7µg/m3Tetrahydrofuran 70-130
1054-Bromofluorobenzene (S)70-130
Page 6 of 10Date:03/08/2024 10:03 AM
Page 31 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44517QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44513
Associated Lab Samples: 97578, 97579, 97580, 97581
LRB-V44513 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/26/24 13:174.750.2021.05µg/m3Acetone
02/26/24 13:171.600.073<0.073µg/m3Benzene
02/26/24 13:176.230.060<0.060µg/m3Carbon Disulfide
02/26/24 13:173.150.155<0.155µg/m3Carbon Tetrachloride
02/26/24 13:172.440.086<0.086µg/m3Chloroform
02/26/24 13:171.030.067<0.067µg/m3Chloromethane
02/26/24 13:173.440.161<0.161µg/m3Cyclohexane
02/26/24 13:172.470.134<0.134µg/m3Dichlorodifluoromethane
02/26/24 13:171.980.095<0.095µg/m3cis-1,2-Dichloroethene
02/26/24 13:172.170.106<0.106µg/m3Ethylbenzene
02/26/24 13:172.460.128<0.128µg/m34-Ethyltoluene
02/26/24 13:173.830.561<0.561µg/m31,1,2-Trichloro-1,2,2-trifluoroethane
02/26/24 13:172.050.143<0.143µg/m3Heptane
02/26/24 13:171.760.047<0.047µg/m3n-Hexane
02/26/24 13:174.920.1391.54µg/m3Isopropyl Alcohol
02/26/24 13:171.470.224<0.224µg/m3Methyl Ethyl Ketone (MEK)
02/26/24 13:171.800.033<0.033µg/m3Methyl tert-butyl ether (MTBE)
02/26/24 13:171.740.488<0.488µg/m3Methylene Chloride
02/26/24 13:172.620.183<0.183µg/m3Naphthalene
02/26/24 13:170.8600.242<0.242µg/m3Propene
02/26/24 13:172.130.124<0.124µg/m3Styrene
02/26/24 13:173.390.181<0.181µg/m3Tetrachloroethene
02/26/24 13:171.470.107<0.107µg/m3Tetrahydrofuran
02/26/24 13:171.880.090<0.090µg/m3Toluene
02/26/24 13:172.150.199<0.199µg/m3Trichloroethene
02/26/24 13:172.810.130<0.130µg/m3Trichlorofluoromethane
02/26/24 13:172.460.110<0.110µg/m31,2,4-Trimethylbenzene
Page 7 of 10Date:03/08/2024 10:03 AM
Page 32 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44517QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44513
Associated Lab Samples: 97578, 97579, 97580, 97581
LRB-V44513 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/26/24 13:172.460.236<0.236µg/m31,3,5-Trimethylbenzene
02/26/24 13:172.170.157<0.157µg/m3o-Xylene
02/26/24 13:175.650.217<0.217µg/m3m,p-Xylene
02/26/24 13:174-Bromofluorobenzene (S)94.1 70-130
LCS-V44513Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
93.211.111.9µg/m3Acetone 70-130
88.114.116.0µg/m3Benzene 70-130
97.415.215.6µg/m3Carbon Disulfide 70-130
87.627.631.5µg/m3Carbon Tetrachloride 70-130
90.922.224.4µg/m3Chloroform 70-130
10310.610.3µg/m3Chloromethane 70-130
88.915.317.2µg/m3Cyclohexane 70-130
93.923.224.7µg/m3Dichlorodifluoromethane 70-130
96.919.219.8µg/m3cis-1,2-Dichloroethene 70-130
94.420.521.7µg/m3Ethylbenzene 70-130
96.323.724.6µg/m34-Ethyltoluene 70-130
97.637.438.3µg/m31,1,2-Trichloro-1,2,2-trifluoroethane 70-130
90.218.520.5µg/m3Heptane 70-130
97.717.217.6µg/m3n-Hexane 70-130
95.111.712.3µg/m3Isopropyl Alcohol 70-130
93.913.914.8µg/m3Methyl Ethyl Ketone (MEK)70-130
94.417.018.0µg/m3Methyl tert-butyl ether (MTBE)70-130
89.615.617.4µg/m3Methylene Chloride 70-130
10226.726.2µg/m3Naphthalene 70-130
Page 8 of 10Date:03/08/2024 10:03 AM
Page 33 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44517QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44513
LCS-V44513Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
93.38.048.61µg/m3Propene 70-130
92.419.721.3µg/m3Styrene 70-130
89.330.333.9µg/m3Tetrachloroethene 70-130
89.713.214.7µg/m3Tetrahydrofuran 70-130
88.216.618.8µg/m3Toluene 70-130
91.024.526.9µg/m3Trichloroethene 70-130
98.227.628.1µg/m3Trichlorofluoromethane 70-130
10124.824.6µg/m31,2,4-Trimethylbenzene 70-130
10225.024.6µg/m31,3,5-Trimethylbenzene 70-130
96.320.921.7µg/m3o-Xylene 70-130
96.742.043.4µg/m3m,p-Xylene 70-130
1014-Bromofluorobenzene (S)70-130
Page 9 of 10Date:03/08/2024 10:03 AM
Page 34 of 38
Quality Control Data
24-053-0009Report No:
Project Description:
Client ID:Hart & Hickman (Charlotte)
PDP-001
QC Prep Batch Method:
Volatile Organic Compounds in Air- GC/MS
TO-15
V44550QC Analytical Batch(es):
Analysis Method:
Analysis Description:
TO-15 Prep
QC Prep:V44549
Associated Lab Samples: 97578, 97579, 97580
LRB-V44549 Matrix: AIRLab Reagent Blank
Parameter
AnalyzedMQLMDLBlank
ResultUnits
%
Recovery
% Rec
Limits
02/27/24 14:294.750.2021.04µg/m3Acetone
02/27/24 14:294-Bromofluorobenzene (S)98.3 70-130
LCS-V44549Laboratory Control Sample
Parameter
LCS %RecLCS
Result
Spike
Conc.Units
% Rec
Limits
94.911.311.9µg/m3Acetone 70-130
1054-Bromofluorobenzene (S)70-130
Page 10 of 10Date:03/08/2024 10:03 AM
Page 35 of 38
Fed Ex
UPS
US Postal
Client
Lab
Courier
Other :
Shipment Receipt Form
Customer Number:
Customer Name:
Report Number:24-053-0009
Hart & Hickman (Charlotte)
01102
Shipping Method
Shipping container/cooler uncompromised?
Thermometer ID:N/A
Chain of Custody (COC) present?Yes No
Yes No Not Present
Yes No Not Present
Yes No
COC agrees with sample label(s)? Yes No
COC properly completed
Samples in proper containers?
Sample containers intact?
Sufficient sample volume for indicated test(s)?
All samples received within holding time?
Cooler temperature in compliance?
Yes No
Yes No
Yes No
Yes No
Yes No
Yes NoCooler/Samples arrived at the laboratory on ice.
Samples were considered acceptable as cooling
process had begun.
Yes No
Yes No N/A
Yes No N/A
Yes No N/ASoil VOA method 5035 – compliance criteria met
Water - Sample containers properly preserved
Water - VOA vials free of headspace Yes No N/A
Trip Blanks received with VOAs
Low concentration EnCore samplers (48 hr)
High concentration pre-weighed (methanol -14 d) Low conc pre-weighed vials (Sod Bis -14 d)
High concentration container (48 hr)
Custody seals intact on shipping container/cooler?
Custody seals intact on sample bottles?
Number of coolers/boxes received
Yes No
1
Signature:Angelo Norvell Date & Time:02/22/2024 12:06:35
Special precautions or instructions included?
Comments:
Page 36 of 38
Page 37 of 38
Page 38 of 38
Select List VOCs TO-15
28-Feb-24
Acetone
Benzene
Carbon Disulfide
Carbon Tetrachloride
Chloroform
Chloromethane
Cyclohexane
cis-1,2-Dichloroethene
Dichlorodifluoromethane
Ethylbenzene
4-Ethyllouene
Heptane
n-Hexane
Isopropyl Alcohol
Methyl Ethyl Ketone (MEK)
Methyl tert butyl ether
Methylene Chloride
Naphthalene
Propene
Styrene
Tetrachloroethene
Tetrahydrofuran
Toluene
Trichloroethene
Trichlorofluoromethane
1,1,2-Trichloro-1,2,2-Trifluoroethane
1,2,4-Trimethylbenzene
1,3,5-Trimethylbenzene
o-Xylene
m,p-Xylene
Xylene (Total)
Page 1

Appendix G

Safety Data Sheets

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 1 of 9
NFPA 704 (Section 16)
EMERGENCY OVERVIEW
DANGER!
EXTREMELY FLAMMABLE - EYE AND MUCOUS MEMBRANE IRRITANT
- EFFECTS CENTRAL NERVOUS SYSTEM - HARMFUL OR FATAL IF
SWALLOWED - ASPIRATION HAZARD
High fire hazard. Keep away from heat, spark, open flame, and other ignition
sources.
If ingested, do NOT induce vomiting, as this may cause chemical pneumonia (fluid in the lungs). Contact
may cause eye, skin and mucous membrane irritation. Harmful if absorbed through the skin. Avoid
prolonged breathing of vapors or mists. Inhalation may cause irritation, anesthetic effects (dizziness,
nausea, headache, intoxication), and respiratory system effects.
Long-term exposure may cause effects to specific organs, such as to the liver, kidneys, blood, nervous
system, and skin. Contains benzene, which can cause blood disease, including anemia and leukemia.

1. CHEMICAL PRODUCT and COMPANY INFORMATION
Hess Corporation
1 Hess Plaza
Woodbridge, NJ 07095-0961
EMERGENCY TELEPHONE NUMBER (24 hrs): CHEMTREC [phone]
COMPANY CONTACT (business hours): Corporate Safety [phone]
MSDS (Environment, Health, Safety) Internet Website www.hess.com
SYNONYMS: Hess Conventional (Oxygenated and Non-oxygenated) Gasoline; Reformulated Gasoline
(RFG); Reformulated Gasoline Blendstock for Oxygenate Blending (RBOB); Unleaded
Motor or Automotive Gasoline
See Section 16 for abbreviations and acronyms.
2. COMPOSITION and INFORMATION ON INGREDIENTS *

INGREDIENT NAME (CAS No.) CONCENTRATION PERCENT BY WEIGHT
Gasoline (86290-81-5) 100
Benzene (71-43-2) 0.1 - 4.9 (0.1 - 1.3 reformulated gasoline)
n-Butane (106-97-8) < 10
Ethyl Alcohol (Ethanol) (64-17-5) 0 - 10
Ethyl benzene (100-41-4) < 3
n-Hexane (110-54-3) 0.5 to 4
Methyl-tertiary butyl ether (MTBE) (1634-04-4) 0 to 15.0
Tertiary-amyl methyl ether (TAME) (994-05-8) 0 to 17.2
Toluene (108-88-3) 1 - 25
1,2,4- Trimethylbenzene (95-63-6) < 6
Xylene, mixed isomers (1330-20-7) 1 - 15

A complex blend of petroleum-derived normal and branched-chain alkane, cycloalkane, alkene, and
aromatic hydrocarbons. May contain antioxidant and multifunctional additives. Non-oxygenated
Conventional Gasoline and RBOB do not have oxygenates (Ethanol or MTBE and/or TAME).

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 2 of 9
Oxygenated Conventional and Reformulated Gasoline will have oxygenates for octane enhancement or
as legally required.

3. HAZARDS IDENTIFICATION

EYES
Moderate irritant. Contact with liquid or vapor may cause irritation.
SKIN
Practically non-toxic if absorbed following acute (single) exposure. May cause skin irritation with
prolonged or repeated contact. Liquid may be absorbed through the skin in toxic amounts if large areas of
skin are exposed repeatedly.
INGESTION
The major health threat of ingestion occurs from the danger of aspiration (breathing) of liquid drops into
the lungs, particularly from vomiting. Aspiration may result in chemical pneumonia (fluid in the lungs),
severe lung damage, respiratory failure and even death.
Ingestion may cause gastrointestinal disturbances, including irritation, nausea, vomiting and diarrhea, and
central nervous system (brain) effects similar to alcohol intoxication. In severe cases, tremors,
convulsions, loss of consciousness, coma, respiratory arrest, and death may occur.
INHALATION
Excessive exposure may cause irritations to the nose, throat, lungs and respiratory tract. Central nervous
system (brain) effects may include headache, dizziness, loss of balance and coordination,
unconsciousness, coma, respiratory failure, and death.
WARNING: the burning of any hydrocarbon as a fuel in an area without adequate ventilation may result
in hazardous levels of combustion products, including carbon monoxide, and inadequate oxygen levels,
which may cause unconsciousness, suffocation, and death.
CHRONIC EFFECTS and CARCINOGENICITY
Contains benzene, a regulated human carcinogen. Benzene has the potential to cause anemia and other
blood diseases, including leukemia, after repeated and prolonged exposure. Exposure to light
hydrocarbons in the same boiling range as this product has been associated in animal studies with
systemic toxicity. See also Section 11 - Toxicological Information.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
Irritation from skin exposure may aggravate existing open wounds, skin disorders, and dermatitis (rash).
Chronic respiratory disease, liver or kidney dysfunction, or pre-existing central nervous system disorders
may be aggravated by exposure.
4. FIRST AID MEASURES
EYES
In case of contact with eyes, immediately flush with clean, low-pressure water for at least 15 min. Hold
eyelids open to ensure adequate flushing. Seek medical attention.
SKIN
Remove contaminated clothing. Wash contaminated areas thoroughly with soap and water or waterless
hand cleanser. Obtain medical attention if irritation or redness develops.
INGESTION

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 3 of 9
DO NOT INDUCE VOMITING. Do not give liquids. Obtain immediate medical attention. If spontaneous
vomiting occurs, lean victim forward to reduce the risk of aspiration. Small amounts of material which
enter the mouth should be rinsed out until the taste is dissipated.
INHALATION
Remove person to fresh air. If person is not breathing, ensure an open airway and provide artificial
respiration. If necessary, provide additional oxygen once breathing is restored if trained to do so. Seek
medical attention immediately.

5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES:
FLASH POINT: -45 oF (-43oC)
AUTOIGNITION TEMPERATURE: highly variable; > 530 oF (>280 oC)
OSHA/NFPA FLAMMABILITY CLASS: 1A (flammable liquid)
LOWER EXPLOSIVE LIMIT (%): 1.4%
UPPER EXPLOSIVE LIMIT (%): 7.6%
FIRE AND EXPLOSION HAZARDS
Vapors may be ignited rapidly when exposed to heat, spark, open flame or other source of ignition.
Flowing product may be ignited by self-generated static electricity. When mixed with air and exposed to
an ignition source, flammable vapors can burn in the open or explode in confined spaces. Being heavier
than air, vapors may travel long distances to an ignition source and flash back. Runoff to sewer may
cause fire or explosion hazard.
EXTINGUISHING MEDIA
SMALL FIRES: Any extinguisher suitable for Class B fires, dry chemical, CO2, water spray, fire fighting
foam, or Halon.
LARGE FIRES: Water spray, fog or fire fighting foam. Water may be ineffective for fighting the fire, but
may be used to cool fire-exposed containers.
During certain times of the year and/or in certain geographical locations, gasoline may contain MTBE
and/or TAME. Firefighting foam suitable for polar solvents is recommended for fuel with greater than
10% oxygenate concentration - refer to NFPA 11 “Low Expansion Foam - 1994 Edition.”
FIRE FIGHTING INSTRUCTIONS
Small fires in the incipient (beginning) stage may typically be extinguished using handheld portable fire
extinguishers and other fire fighting equipment.
Firefighting activities that may result in potential exposure to high heat, smoke or toxic by-products of
combustion should require NIOSH/MSHA- approved pressure-demand self-contained breathing
apparatus with full facepiece and full protective clothing.
Isolate area around container involved in fire. Cool tanks, shells, and containers exposed to fire and
excessive heat with water. For massive fires the use of unmanned hose holders or monitor nozzles may
be advantageous to further minimize personnel exposure. Major fires may require withdrawal, allowing
the tank to burn. Large storage tank fires typically require specially trained personnel and equipment to
extinguish the fire, often including the need for properly applied fire fighting foam.
See Section 16 for the NFPA 704 Hazard Rating.

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 4 of 9

6. ACCIDENTAL RELEASE MEASURES
ACTIVATE FACILITY SPILL CONTINGENCY or EMERGENCY PLAN.
Evacuate nonessential personnel and remove or secure all ignition sources. Consider wind direction; stay
upwind and uphill, if possible. Evaluate the direction of product travel, diking, sewers, etc. to confirm spill
areas. Spills may infiltrate subsurface soil and groundwater; professional assistance may be necessary
to determine the extent of subsurface impact.
Carefully contain and stop the source of the spill, if safe to do so. Protect bodies of water by diking,
absorbents, or absorbent boom, if possible. Do not flush down sewer or drainage systems, unless
system is designed and permitted to handle such material. The use of fire fighting foam may be useful in
certain situations to reduce vapors. The proper use of water spray may effectively disperse product
vapors or the liquid itself, preventing contact with ignition sources or areas/equipment that require
protection.
Take up with sand or other oil absorbing materials. Carefully shovel, scoop or sweep up into a waste
container for reclamation or disposal - caution, flammable vapors may accumulate in closed containers.
Response and clean-up crews must be properly trained and must utilize proper protective equipment
(see Section 8).
7. HANDLING and STORAGE
HANDLING PRECAUTIONS
******USE ONLY AS A MOTOR FUEL******
******DO NOT SIPHON BY MOUTH******
Handle as a flammable liquid. Keep away from heat, sparks, and open flame! Electrical equipment
should be approved for classified area. Bond and ground containers during product transfer to reduce the
possibility of static-initiated fire or explosion.
Special slow load procedures for "switch loading" must be followed to avoid the static ignition hazard that
can exist when higher flash point material (such as fuel oil) is loaded into tanks previously containing low
flash point products (such as this product) - see API Publication 2003, "Protection Against Ignitions
Arising Out Of Static, Lightning and Stray Currents.
STORAGE PRECAUTIONS
Keep away from flame, sparks, excessive temperatures and open flame. Use approved vented
containers. Keep containers closed and clearly labeled. Empty product containers or vessels may contain
explosive vapors. Do not pressurize, cut, heat, weld or expose such containers to sources of ignition.
Store in a well-ventilated area. This storage area should comply with NFPA 30 "Flammable and
Combustible Liquid Code". Avoid storage near incompatible materials. The cleaning of tanks previously
containing this product should follow API Recommended Practice (RP) 2013 "Cleaning Mobile Tanks In
Flammable and Combustible Liquid Service" and API RP 2015 "Cleaning Petroleum Storage Tanks".
WORK/HYGIENIC PRACTICES
Emergency eye wash capability should be available in the near proximity to operations presenting a
potential splash exposure. Use good personal hygiene practices. Avoid repeated and/or prolonged skin
exposure. Wash hands before eating, drinking, smoking, or using toilet facilities. Do not use as a
cleaning solvent on the skin. Do not use solvents or harsh abrasive skin cleaners for washing this product
from exposed skin areas. Waterless hand cleaners are effective. Promptly remove contaminated
clothing and launder before reuse. Use care when laundering to prevent the formation of flammable
vapors which could ignite via washer or dryer. Consider the need to discard contaminated leather shoes
and gloves.

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 5 of 9

8. EXPOSURE CONTROLS and PERSONAL PROTECTION
EXPOSURE LIMITS
Component (CAS No.) Exposure Limits
Source TWA
(ppm)
STEL
(ppm)
Note
Gasoline (86290-81-5) ACGIH 300 500 A3
Benzene (71-43-2) OSHA
ACGIH
USCG
1
0.5
1
5
2.5
5
Carcinogen
A1, skin

n-Butane (106-97-8) ACGIH 1000 -- Aliphatic Hydrocarbon Gases Alkane (C1-C4)
Ethyl Alcohol (ethanol) (64-17-5) OSHA
ACGIH
1000
1000
--
--

A4
Ethyl benzene (100-41-4) OSHA
ACGIH
100
100
--
125

A3
n-Hexane (110-54-3) OSHA
ACGIH
500
50
--
--

Skin
Methyl-tertiary butyl ether [MTBE] (1634-04-4) ACGIH 50 A3
Tertiary-amyl methyl ether [TAME] (994-05-8) None established
Toluene (108-88-3) OSHA
ACGIH
200
20

--
Ceiling: 300 ppm; Peak: 500 ppm (10 min.)
A4
1,2,4- Trimethylbenzene (95-63-6) ACGIH 25 --
Xylene, mixed isomers (1330-20-7) OSHA
ACGIH
100
100
--
150

A4

ENGINEERING CONTROLS
Use adequate ventilation to keep vapor concentrations of this product below occupational exposure and
flammability limits, particularly in confined spaces.
EYE/FACE PROTECTION
Safety glasses or goggles are recommended where there is a possibility of splashing or spraying.
SKIN PROTECTION
Gloves constructed of nitrile or neoprene are recommended. Chemical protective clothing such as that
made of of E.I. DuPont Tychem ®, products or equivalent is recommended based on degree of exposure.
Note: The resistance of specific material may vary from product to product as well as with degree of
exposure. Consult manufacturer specifications for further information.
RESPIRATORY PROTECTION
A NIOSH-approved air-purifying respirator with organic vapor cartridges or canister may be permissible
under certain circumstances where airborne concentrations are or may be expected to exceed exposure
limits or for odor or irritation. Protection provided by air-purifying respirators is limited. Refer to OSHA 29
CFR 1910.134, NIOSH Respirator Decision Logic, and the manufacturer for additional guidance on
respiratory protection selection and limitations.
Use a positive pressure, air-supplied respirator if there is a potential for uncontrolled release, exposure
levels are not known, in oxygen-deficient atmospheres, or any other circumstance where an air-purifying
respirator may not provide adequate protection.
9. PHYSICAL and CHEMICAL PROPERTIES
APPEARANCE
A translucent, straw-colored or light yellow liquid

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 6 of 9
ODOR
A strong, characteristic aromatic hydrocarbon odor. Oxygenated gasoline with MTBE and/or TAME may
have a sweet, ether-like odor and is detectable at a lower concentration than non-oxygenated gasoline.
ODOR THRESHOLD
Odor Detection Odor Recognition
Non-oxygenated gasoline: 0.5 - 0.6 ppm 0.8 - 1.1 ppm
Gasoline with 15% MTBE: 0.2 - 0.3 ppm 0.4 - 0.7 ppm
Gasoline with 15% TAME: 0.1 ppm 0.2 ppm
BASIC PHYSICAL PROPERTIES
BOILING RANGE: 85 to 437 oF (39 to 200 oC)
VAPOR PRESSURE: 6.4 - 15 RVP @ 100 oF (38 oC) (275-475 mm Hg @ 68 oF (20 oC)
VAPOR DENSITY (air = 1): AP 3 to 4
SPECIFIC GRAVITY (H2O = 1): 0.70 – 0.78
EVAPORATION RATE: 10-11 (n-butyl acetate = 1)
PERCENT VOLATILES: 100 %
SOLUBILITY (H2O): Non-oxygenated gasoline - negligible (< 0.1% @ 77 oF). Gasoline with 15%
MTBE - slight (0.1 - 3% @ 77 oF); ethanol is readily soluble in water
10. STABILITY and REACTIVITY )
STABILITY: Stable. Hazardous polymerization will not occur.

CONDITIONS TO AVOID
Avoid high temperatures, open flames, sparks, welding, smoking and other ignition sources
INCOMPATIBLE MATERIALS
Keep away from strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS
Carbon monoxide, carbon dioxide and non-combusted hydrocarbons (smoke). Contact with nitric and
sulfuric acids will form nitrocresols that can decompose violently.
11. TOXICOLOGICAL PROPERTIES
ACUTE TOXICITY
Acute Dermal LD50 (rabbits): > 5 ml/kg Acute Oral LD50 (rat): 18.75 ml/kg
Primary dermal irritation (rabbits): slightly irritating Draize eye irritation (rabbits): non-irritating
Guinea pig sensitization: negative
CHRONIC EFFECTS AND CARCINOGENICITY
Carcinogenicity: OSHA: NO IARC: YES - 2B NTP: NO ACGIH: YES (A3)
IARC has determined that gasoline and gasoline exhaust are possibly carcinogenic in humans. Inhalation
exposure to completely vaporized unleaded gasoline caused kidney cancers in male rats and liver tumors
in female mice. The U.S. EPA has determined that the male kidney tumors are species-specific and are
irrelevant for human health risk assessment. The significance of the tumors seen in female mice is not
known. Exposure to light hydrocarbons in the same boiling range as this product has been associated in
animal studies with effects to the central and peripheral nervous systems, liver, and kidneys. The
significance of these animal models to predict similar human response to gasoline is uncertain.
This product contains benzene. Human health studies indicate that prolonged and/or repeated
overexposure to benzene may cause damage to the blood-forming system (particularly bone marrow),
and serious blood disorders such as aplastic anemia and leukemia. Benzene is listed as a human
carcinogen by the NTP, IARC, OSHA and ACGIH.

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 7 of 9
This product may contain methyl tertiary butyl ether (MTBE ): animal and human health effects studies
indicate that MTBE may cause eye, skin, and respiratory tract irritation, central nervous system
depression and neurotoxicity. MTBE is classified as an animal carcinogen (A3) by the ACGIH.
12. ECOLOGICAL INFORMATION
Keep out of sewers, drainage areas and waterways. Report spills and releases, as applicable, under
Federal and State regulations. If released, oxygenates such as ethers and alcohols will be expected to
exhibit fairly high mobility in soil, and therefore may leach into groundwater. The API (www.api.org)
provides a number of useful references addressing petroleum and oxygenate contamination of
groundwater.
13. DISPOSAL CONSIDERATIONS
Consult federal, state and local waste regulations to determine appropriate disposal options.

14. TRANSPORTATION INFORMATION

DOT PROPER SHIPPING NAME: Gasoline
DOT HAZARD CLASS and PACKING GROUP: 3, PG II
DOT IDENTIFICATION NUMBER: UN 1203
DOT SHIPPING LABEL:

FLAMMABLE LIQUID
PLACARD:

15. REGULATORY INFORMATION
U.S. FEDERAL, STATE, and LOCAL REGULATORY INFORMATION
This product and its constituents listed herein are on the EPA TSCA Inventory. Any spill or uncontrolled
release of this product, including any substantial threat of release, may be subject to federal, state and/or
local reporting requirements. This product and/or its constituents may also be subject to other federal,
state, or local regulations; consult those regulations applicable to your facility/operation.
CLEAN WATER ACT (OIL SPILLS)
Any spill or release of this product to "navigable waters" (essentially any surface water, including certain
wetlands) or adjoining shorelines sufficient to cause a visible sheen or deposit of a sludge or emulsion
must be reported immediately to the National Response Center (1-800-424-8802) as required by U.S.
Federal Law. Also contact appropriate state and local regulatory agencies as required.
CERCLA SECTION 103 and SARA SECTION 304 (RELEASE TO THE ENVIRONMENT)
The CERCLA definition of hazardous substances contains a “petroleum exclusion” clause which exempts
crude oil, refined, and unrefined petroleum products and any indigenous components of such. However,
other federal reporting requirements (e.g., SARA Section 304 as well as the Clean Water Act if the spill
occurs on navigable waters) may still apply.
SARA SECTION 311/312 - HAZARD CLASSES
ACUTE HEALTH CHRONIC HEALTH FIRE SUDDEN RELEASE OF PRESSURE REACTIVE
X X X -- --
SARA SECTION 313 - SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of section 313 of
the Emergency Planning and Community Right-To-Know Act (EPCRA) of 1986 and of 40 CFR 372:
INGREDIENT NAME (CAS NUMBER) CONCENTRATION WT. PERCENT
Benzene (71-43-2) 0.1 to 4.9 (0.1 to 1.3 for reformulated gasoline)
Ethyl benzene (100-41-4) < 3

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 8 of 9
n-Hexane (110-54-3) 0.5 to 4
Methyl-tertiary butyl ether (MTBE) (1634-04-4) 0 to 15.0
Toluene (108-88-3) 1 to 15
1,2,4- Trimethylbenzene (95-63-6) < 6
Xylene, mixed isomers (1330-20-7) 1 to 15
US EPA guidance documents (www.epa.gov/tri) for reporting Persistent Bioaccumulating Toxics (PBTs)
indicate this product may contain the following deminimis levels of toxic chemicals subject to Section 313
reporting:
INGREDIENT NAME (CAS NUMBER) CONCENTRATION - Parts per million (ppm) by weight
Polycyclic aromatic compounds (PACs)
Benzo (g,h,i) perylene (191-24-2)
Lead (7439-92-1)
17
2.55
0.079

CALIFORNIA PROPOSITION 65 LIST OF CHEMICALS
This product contains the following chemicals that are included on the Proposition 65 “List of Chemicals”
required by the California Safe Drinking Water and Toxic Enforcement Act of 1986:

INGREDIENT NAME (CAS NUMBER) Date Listed
Benzene 2/27/1987
Ethyl benzene 6/11/2004
Toluene 1/1/1991

CANADIAN REGULATORY INFORMATION (WHMIS)
Class B, Division 2 (Flammable Liquid)
Class D, Division 2A (Very toxic by other means) and Class D, Division 2B (Toxic by other means)
16. OTHER INFORMATION

NFPA® HAZARD RATING HEALTH: 1 Slight
FIRE: 3 Serious
REACTIVITY: 0 Minimal
HMIS® HAZARD RATING HEALTH: 1 * Slight
FIRE: 3 Serious
PHYSICAL: 0 Minimal
* CHRONIC
SUPERSEDES MSDS DATED: 07/01/06
ABBREVIATIONS:
AP = Approximately < = Less than > = Greater than
N/A = Not Applicable N/D = Not Determined ppm = parts per million
ACRONYMS:
ACGIH American Conference of Governmental
Industrial Hygienists
AIHA American Industrial Hygiene Association
ANSI American National Standards Institute
[phone]
API American Petroleum Institute
[phone]
CERCLA Comprehensive Emergency Response,
Compensation, and Liability Act
DOT U.S. Department of Transportation
[General Info: [phone]]
EPA U.S. Environmental Protection Agency
HMIS Hazardous Materials Information System

MATERIAL SAFETY DATA SHEET
Gasoline, All Grades MSDS No. 9950

Revision Date: 09/25/2007 Page 9 of 9
IARC International Agency For Research On
Cancer
MSHA Mine Safety and Health Administration
NFPA National Fire Protection Association
[phone]
NIOSH National Institute of Occupational Safety
and Health
NOIC Notice of Intended Change (proposed
change to ACGIH TLV)
NTP National Toxicology Program
OPA Oil Pollution Act of 1990
OSHA U.S. Occupational Safety & Health
Administration
PEL Permissible Exposure Limit (OSHA)
RCRA Resource Conservation and Recovery Act
REL Recommended Exposure Limit (NIOSH)
SARA Superfund Amendments and
Reauthorization Act of 1986 Title III
SCBA Self-Contained Breathing Apparatus
SPCC Spill Prevention, Control, and
Countermeasures
STEL Short-Term Exposure Limit (generally 15
minutes)
TLV Threshold Limit Value (ACGIH)
TSCA Toxic Substances Control Act
TWA Time Weighted Average (8 hr.)
WEEL Workplace Environmental Exposure
Level (AIHA)
WHMIS Workplace Hazardous Materials
Information System (Canada)

DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES
Information presented herein has been compiled from sources considered to be dependable, and is accurate and reliable to the best
of our knowledge and belief, but is not guaranteed to be so. Since conditions of use are beyond our control, we make no warranties,
expressed or implied, except those that may be contained in our written contract of sale or acknowledgment.
Vendor assumes no responsibility for injury to vendee or third persons proximately caused by the material if reasonable safety
procedures are not adhered to as stipulated in the data sheet. Additionally, vendor assumes no responsibility for injury to vendee or
third persons proximately caused by abnormal use of the material, even if reasonable safety procedures are followed. Furthermore,
vendee assumes the risk in their use of the material.
SAFETY DATA SHEET
1. Identification
Product identifier Oatey PVC Heavy Duty Clear or Gray Cement
Other means of identification
SDS number 1102E
Synonyms Part Numbers: Clear 30850, 30863, 30876(TV), 30882, 31008(TV), 31011, 31950, 31951, 31952,
31953 Gray 30349, 31093, 31094, 31095, 31105, 31118, 31978, 31979, 31980, 31981, 32050,
32051, 32052, 32210, 32211
Recommended use Joining PVC Pipes
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Company Name Oatey Co.
Address 4700 West 160th St.
Cleveland, OH 44135
Telephone [phone]
E-mail [e-mail]
Transport Emergency Chemtrec 1-800-424-9300 (Outside the US 1-703-527-3887)
Emergency First Aid 1-877-740-5015
Contact person MSDS Coordinator
2. Hazard(s) identification
Category 2Flammable liquidsPhysical hazards
Category 4Acute toxicity, oralHealth hazards
Category 2Skin corrosion/irritation
Category 2ASerious eye damage/eye irritation
Category 3 respiratory tract irritationSpecific target organ toxicity, single exposure
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 1Aspiration hazard
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Highly flammable liquid and vapor. Harmful if swallowed. May be fatal if swallowed and enters
airways. Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation. May
cause drowsiness or dizziness.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only outdoors or in a
well-ventilated area. Keep container tightly closed. Ground/bond container and receiving
equipment. Use explosion-proof electrical/ventilating/lighting equipment. Use only non-sparking
tools. Take precautionary measures against static discharge. Avoid breathing mist or vapor. Wash
thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective
gloves/protective clothing/eye protection/face protection.
Response Rinse mouth. Do NOT induce vomiting. If skin irritation occurs: Get medical advice/attention. If
eye irritation persists: Get medical advice/attention. Take off contaminated clothing and wash
before reuse. In case of fire: Use appropriate media to extinguish.
Storage Store in a well-ventilated place. Keep container tightly closed. Keep cool. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Oatey PVC Heavy Duty Clear or Gray Cement SDS US
920700 Version #: 02 Revision date:12-5-2017 Issue date:8-4-2014 1 / 10
Hazard(s) not otherwise
classified (HNOC)
Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.
May form explosive peroxides. Contains a chemical classified by the US EPA as a suspected
possible carcinogen.
Supplemental information
Not applicable.
3. Composition/information on ingredients
Mixtures
109-99-9 30-60Furan, Tetrahydro-
CAS number %Chemical name
67-64-1 10-302-Propanone
108-94-1 10-30Cyclohexanone
9002-86-2 10-30Polyvinyl chloride
78-93-3 5-10Methyl ethyl ketone
112945-52-5 1-5Colloidal silicon dioxide
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Skin contact Take off immediately all contaminated clothing. Wash with plenty of soap and water. If skin
irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before
reuse.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Ingestion Call a physician or poison control center immediately. Do not induce vomiting. If vomiting occurs,
keep head low so that stomach content doesn't get into the lungs. Aspiration may cause
pulmonary edema and pneumonitis.
Most important
symptoms/effects, acute and
delayed
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation.
Vapors have a narcotic effect and may cause headache, fatigue, dizziness and nausea. May
cause redness and pain.
Indication of immediate
medical attention and special
treatment needed
Provide general supportive measures and treat symptomatically. Thermal burns: Flush with water
immediately. While flushing, remove clothes which do not adhere to affected area. Call an
ambulance. Continue flushing during transport to hospital. In case of shortness of breath, give
oxygen. Keep victim warm. Keep victim under observation. Symptoms may be delayed.
General information Take off all contaminated clothing immediately. IF exposed or concerned: Get medical
advice/attention. Ensure that medical personnel are aware of the material(s) involved, and take
precautions to protect themselves. Wash contaminated clothing before reuse.
5. Fire-fighting measures
Suitable extinguishing media Alcohol resistant foam. Water fog. Dry chemical powder. Carbon dioxide (CO2).
Unsuitable extinguishing
media
Do not use water jet as an extinguisher, as this will spread the fire.
Specific hazards arising from
the chemical
Vapors may form explosive mixtures with air. Vapors may travel considerable distance to a source
of ignition and flash back. During fire, gases hazardous to health may be formed.
Special protective equipment
and precautions for firefighters
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Fire fighting
equipment/instructions
In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do
so without risk.
Specific methods Use standard firefighting procedures and consider the hazards of other involved materials.
General fire hazards Highly flammable liquid and vapor. This product contains tetrahydrofuran that may form explosive
organic peroxide when exposed to air or light or with age.
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 2 / 10
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
Wear appropriate protective equipment and clothing during clean-up. Avoid inhalation of vapors or
mists. Do not touch damaged containers or spilled material unless wearing appropriate protective
clothing. Ventilate closed spaces before entering them. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Methods and materials for
containment and cleaning up
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Take
precautionary measures against static discharge. Use only non-sparking tools. Keep combustibles
(wood, paper, oil, etc.) away from spilled material.
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is
possible. Cover with plastic sheet to prevent spreading. Use a non-combustible material like
vermiculite, sand or earth to soak up the product and place into a container for later disposal. Use
water spray to reduce vapors or divert vapor cloud drift. Prevent entry into waterways, sewer,
basements or confined areas. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Environmental precautions Avoid discharge into drains, water courses or onto the ground.
7. Handling and storage
Precautions for safe handling Vapors may form explosive mixtures with air. Do not handle, store or open near an open flame,
sources of heat or sources of ignition. Protect material from direct sunlight. Take precautionary
measures against static discharges. All equipment used when handling the product must be
grounded. Use non-sparking tools and explosion-proof equipment. Do not taste or swallow. Avoid
breathing mist or vapor. Avoid contact with skin. Avoid contact with eyes. Avoid prolonged
exposure. Avoid contact with clothing. Provide adequate ventilation. Wear appropriate personal
protective equipment. Observe good industrial hygiene practices. When using, do not eat, drink or
smoke. Wash hands thoroughly after handling.
Conditions for safe storage,
including any incompatibilities
Store locked up. Keep away from heat, sparks and open flame. Prevent electrostatic charge
build-up by using common bonding and grounding techniques. Store in original tightly closed
container. Store in a cool, dry place out of direct sunlight. Store in a well-ventilated place. Store
away from incompatible materials (see Section 10 of the SDS). Keep in an area equipped with
sprinklers.
8. Exposure controls/personal protection
Occupational exposure limits
U.S. - OSHA
ValueType FormComponents
TWA 0.8 mg/m3 Unspecified.Colloidal silicon dioxide
(CAS 112945-52-5)
20 mppcf Unspecified.
US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
ValueTypeComponents
STEL 5 ppmPolyvinyl chloride (CAS
9002-86-2)
TWA 1 ppm
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueType FormComponents
PEL 2400 mg/m32-Propanone (CAS 67-64-1)
1000 ppm
PEL 200 mg/m3Cyclohexanone (CAS
108-94-1)
50 ppm
PEL 590 mg/m3Furan, Tetrahydro- (CAS
109-99-9)
200 ppm
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 3 / 10
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueType FormComponents
PEL 590 mg/m3Methyl ethyl ketone (CAS
78-93-3)
200 ppm
PEL 5 mg/m3 Respirable fraction.Polyvinyl chloride (CAS
9002-86-2)
15 mg/m3 Total dust.
US. OSHA Table Z-3 (29 CFR 1910.1000)
ValueTypeComponents
TWA 0.8 mg/m3Colloidal silicon dioxide
(CAS 112945-52-5)
20 mppcf
US. ACGIH Threshold Limit Values
ValueType FormComponents
STEL 750 ppm2-Propanone (CAS 67-64-1)
TWA 500 ppm
STEL 50 ppmCyclohexanone (CAS
108-94-1)
TWA 20 ppm
STEL 100 ppmFuran, Tetrahydro- (CAS
109-99-9)
TWA 50 ppm
STEL 300 ppmMethyl ethyl ketone (CAS
78-93-3)
TWA 200 ppm
TWA 1 mg/m3 Respirable fraction.Polyvinyl chloride (CAS
9002-86-2)
U.S. - NIOSH
ValueType FormComponents
REL 6 mg/m3 Unspecified.Colloidal silicon dioxide
(CAS 112945-52-5)
US. NIOSH: Pocket Guide to Chemical Hazards
ValueTypeComponents
TWA 590 mg/m32-Propanone (CAS 67-64-1)
250 ppm
TWA 6 mg/m3Colloidal silicon dioxide
(CAS 112945-52-5)
TWA 100 mg/m3Cyclohexanone (CAS
108-94-1)
25 ppm
STEL 735 mg/m3Furan, Tetrahydro- (CAS
109-99-9)
250 ppm
TWA 590 mg/m3
200 ppm
STEL 885 mg/m3Methyl ethyl ketone (CAS
78-93-3)
300 ppm
TWA 590 mg/m3
200 ppm
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2014 Issue date: 8-4-2014 4 / 10
Biological limit values
ACGIH Biological Exposure Indices
Value Sampling TimeDeterminant SpecimenComponents
50 mg/l Acetone Urine *2-Propanone (CAS 67-64-1)
80 mg/l 1,2-Cyclohexan
ediol,with
hydrolysis
Urine *Cyclohexanone (CAS
108-94-1)
8 mg/l Cyclohexanol,
with hydrolysis
Urine *
2 mg/l Tetrahydrofura
n
Urine *Furan, Tetrahydro- (CAS
109-99-9)
2 mg/l MEK Urine *Methyl ethyl ketone (CAS
78-93-3)
* - For sampling details, please see the source document.
Exposure guidelines
US - California OELs: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
US - Minnesota Haz Subs: Skin designation applies
Cyclohexanone (CAS 108-94-1)Skin designation applies.
US - Tennessee OELs: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
US ACGIH Threshold Limit Values: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
Furan, Tetrahydro- (CAS 109-99-9)Can be absorbed through the skin.
US. NIOSH: Pocket Guide to Chemical Hazards
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
Appropriate engineering
controls
Explosion-proof general and local exhaust ventilation. Good general ventilation (typically 10 air
changes per hour) should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency
shower must be available when handling this product.
Individual protection measures, such as personal protective equipment
Eye/face protection Wear safety glasses with side shields (or goggles).
Skin protection
Hand protection Wear appropriate chemical resistant gloves.
Other Wear appropriate chemical resistant clothing.
Respiratory protection If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.
General hygiene
considerations
When using, do not eat, drink or smoke. Wash hands after handling and before eating.
9. Physical and chemical properties
Appearance Opaque.or Translucent.
Physical state Liquid.
Form Liquid.
Color Gray or Clear.
Odor Solvent.
Odor threshold Not available.
pH Not available.
Melting point/freezing point Not available.
Initial boiling point and boiling
range
151 °F (66.11 °C)
Flash point 14.0 - 23.0 °F (-10.0 - -5.0 °C)
Evaporation rate 5.5 - 8
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 5 / 10
Flammability (solid, gas)Not available.
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
Not available.
Flammability limit - upper
(%)
Not available.
Explosive limit - lower (%)Not available.
Explosive limit - upper (%)Not available.
Vapor pressure 145 mm Hg @ 20 C
Vapor density 2.5
Relative density 0.88 - 0.92
Solubility(ies)
Solubility (water)Negligible
Partition coefficient
(n-octanol/water)
Auto-ignition temperature
Decomposition temperature
Viscosity
Other information
Bulk density
VOC (Weight %)
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Incompatible materials
Hazardous decomposition
products
Not available.
Not available.
Not available.
1200 - 2500 cP
7.5 lb/gal
<510 g/l SQACMD 1168/M316A
The product is stable and non-reactive under normal conditions of use, storage and transport.
Material is stable under normal conditions.
No dangerous reaction known under conditions of normal use.
Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the
flash point. Contact with incompatible materials.
Acids. Strong oxidizing agents. Ammonia. Amines. Isocyanates. Caustics.
No hazardous decomposition products are known.
11. Toxicological information
Information on likely routes of exposure
Inhalation May be fatal if swallowed and enters airways. Vapors have a narcotic effect and may cause
headache, fatigue, dizziness and nausea. Prolonged inhalation may be harmful. May cause
irritation to the respiratory system.
Skin contact Causes skin irritation.
Eye contac Causes serious eye irritation.
Ingestion May be fatal if swallowed and enters airways. Harmful if swallowed.
Symptoms related to the
physical, chemical and
toxicological characteristics
Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Skin irritation. May
cause redness and pain. Symptoms of overexposure may be headache, dizziness, tiredness,
nausea and vomiting.
Information on toxicological effects
Acute toxicit May be fatal if swallowed and enters airways. Narcotic effects. May cause respiratory irritation.
Test ResultsComponentsSpecies
Cyclohexanone (CAS 108-94-1)
LD50 Rabbit
Dermal
Acute
948 mg/kg
LC50 Rat
Inhalation
8000 ppm, 4 hours
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 6 / 10
Test ResultsComponents Species
LD50 Rat
Oral
1540 mg/kg
* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation Causes skin irritation.
Serious eye damage/eye
irritation
Causes serious eye irritation.
Respiratory or skin sensitization
Respiratory sensitization Not available.
Skin sensitization This product is not expected to cause skin sensitization.
Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity Suspected of causing cancer. In 2012 USEPA Integrated Risk Information System (IRIS)
reviewed a two species inhalation lifetime study on THF conducted by NTP (1998). Male rats
developed renal tumors and female mice developed liver tumors while neither the female rats nor
the male mice showed similar results. Because the carcinogenic mechanisms could not be
identified clearly in either species for either tumor, the EPA determined that the male rat and
female mouse findings are relevant to the assessment of carcinogenic potential in humans.
Therefore, the IRIS review concludes that these data in aggregate indicate that there is
"suggestive evidence of carcinogenic potential" following exposure to THF by all routes of
exposure. This product contains polyvinyl chloride (PVC) that is not a fabricated product, and is
therefore, defined and regulated as a toxic and hazardous substance under 29 C.F.R. §
1910.1017 due to the presumed presence of residual vinyl chloride monomer. The concentrations
of residual vinyl chloride calculated to be contained in this product are well below the threshold for
classification in accordance with 29 C.F.R. § 1910.1200.
IARC Monographs. Overall Evaluation of Carcinogenicity
Colloidal silicon dioxide (CAS 112945-52-5) 3 Not classifiable as to carcinogenicity to humans.
Cyclohexanone (CAS 108-94-1) 3 Not classifiable as to carcinogenicity to humans.
Polyvinyl chloride (CAS 9002-86-2) 3 Not classifiable as to carcinogenicity to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Polyvinyl chloride (CAS 9002-86-2) Cancer
Reproductive toxicity This product is not expected to cause reproductive or developmental effects.
Specific target organ toxicity -
single exposure
Respiratory tract irritation. Narcotic effects.
Specific target organ toxicity -
repeated exposure
Not classified.
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged inhalation may be harmful.
12. Ecological information
Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude the
possibility that large or frequent spills can have a harmful or damaging effect on the environment.
Components Test ResultsSpecies
* Estimates for product may be based on additional component data not shown.
Cyclohexanone (CAS 108-94-1)
Aquatic
LC50Fish 481 - 578 mg/l, 96 hoursFathead minnow (Pimephales promelas)
Persistence and degradability No data is available on the degradability of this product.
Bioaccumulative potential No data available.
Partition coefficient n-octanol / water (log Kow)
2-Propanone (CAS 67-64-1)-0.24
Cyclohexanone (CAS 108-94-1)0.81
Furan, Tetrahydro- (CAS 109-99-9)0.46
Methyl ethyl ketone (CAS 78-93-3)0.29
Mobility in soil No data available.
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 7 / 10
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site. This material
and its container must be disposed of as hazardous waste. Do not allow this material to drain into
sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Waste from residues / unused
products
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
14. Transport information
DOT
UN1133UN number
AdhesivesUN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
3Label(s)
IIPacking group
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
T11, TP1, TP8, TP27Special provisions
150Packaging exceptions
201Packaging non bulk
243Packaging bulk
IATA
UN1133UN number
AdhesivesUN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIPacking group
No.Environmental hazards
3LERG Code
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
IMDG
UN1133UN number
ADHESIVESUN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIPacking group
No.Marine pollutant
Environmental hazards
F-E, S-DEmS
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
Not available.Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 8 / 10
15. Regulatory information
US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
All components are on the U.S. EPA TSCA Inventory List.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Polyvinyl chloride (CAS 9002-86-2)Cancer
Central nervous system
Liver
Blood
Flammability
CERCLA Hazardous Substance List (40 CFR 302.4)
2-Propanone (CAS 67-64-1)LISTED
Cyclohexanone (CAS 108-94-1)LISTED
Furan, Tetrahydro- (CAS 109-99-9)LISTED
Methyl ethyl ketone (CAS 78-93-3)LISTED
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Hazard categories Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous
chemical
No
SARA 313 (TRI reporting)
Not regulated.
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act
(SDWA)
Not regulated.
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and
Chemical Code Number
2-Propanone (CAS 67-64-1)6532
Methyl ethyl ketone (CAS 78-93-3)6714
Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c))
2-Propanone (CAS 67-64-1)35 %WV
Methyl ethyl ketone (CAS 78-93-3)35 %WV
DEA Exempt Chemical Mixtures Code Number
2-Propanone (CAS 67-64-1)6532
Methyl ethyl ketone (CAS 78-93-3)6714
US state regulations
US. Massachusetts RTK - Substance List
2-Propanone (CAS 67-64-1)
Colloidal silicon dioxide (CAS 112945-52-5)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. New Jersey Worker and Community Right-to-Know Act
2-Propanone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
SDS USOatey PVC Heavy Duty Clear or Gray Cement
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 9 / 10
Polyvinyl chloride (CAS 9002-86-2)
US. Pennsylvania Worker and Community Right-to-Know Law
2-Propanone (CAS 67-64-1)
Colloidal silicon dioxide (CAS 112945-52-5)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. Rhode Island RTK
2-Propanone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins. This product contains trace amounts of chemicals
known to the state of California to cause cancer. Under normal use conditions, exposure to these chemicals at levels above
the State of California “No significant Risk Level” (NSRL) are unlikely. The use of proper personal protective equipment
(PPE) and ventilation guidelines noted in Section 8 will minimize exposure levels to these chemicals.
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australian Inventory of Chemical Substances (AICS) YesAustralia
Domestic Substances List (DSL) YesCanada
Non-Domestic Substances List (NDSL) NoCanada
Inventory of Existing Chemical Substances in China (IECSC) YesChina
European Inventory of Existing Commercial Chemical
Substances (EINECS)
NoEurope
European List of Notified Chemical Substances (ELINCS) NoEurope
Inventory of Existing and New Chemical Substances (ENCS) YesJapan
Existing Chemicals List (ECL) YesKorea
New Zealand Inventory YesNew Zealand
Philippine Inventory of Chemicals and Chemical Substances
(PICCS)
YesPhilippines
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
"No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
Toxic Substances Control Act (TSCA) Inventory YesUnited States & Puerto Rico
16. Other information, including date of preparation or last revision
Issue date 04-August-2014
Revision date 15-December-2014
Version #02
HMIS® ratings Health: 2
Flammability: 3
Physical hazard: 0
Disclaimer The information in the sheet was written based on the best knowledge and experience currently
available.
Oatey PVC Heavy Duty Clear or Gray Cement SDS US
920700 Version #: 02 Revision date: 12-5-2017 Issue date: 8-4-2014 10 / 10
SAFETY DATA SHEET
1. Identification
Oatey Purple Primer- NSF Listed for PVC and CPVCProduct identifier
Other means of identification
1402EProduct code
Part Numbers: 30755(TV), 30756(TV), 30757(TV), 30758, 30759, 30927Synonyms
Joining PVC PipesRecommended use
None known.Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
Company Name Oatey Co.
Address 4700 West 160th St.
Cleveland, OH 44135
Telephone [phone]
E-mail [e-mail]
Transport Emergency Chemtrec 1-800-424-9300 (Outside the US 1-703-527-3887)
Emergency First Aid 1-877-740-5015
Contact person MSDS Coordinator
2. Hazard(s) identification
Category 2Flammable liquidsPhysical hazards
Category 4Acute toxicity, oralHealth hazards
Category 2Skin corrosion/irritation
Category 2ASerious eye damage/eye irritation
Category 3 respiratory tract irritationSpecific target organ toxicity, single exposure
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 1Aspiration hazard
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Highly flammable liquid and vapor. Harmful if swallowed. May be fatal if swallowed and enters
airways. Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation. May
cause drowsiness or dizziness.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Keep container tightly
closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist or vapor. Wash thoroughly after
handling. Do not eat, drink or smoke when using this product. Use only outdoors or in a
well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection.
Response If swallowed: Immediately call a poison center/doctor. If on skin (or hair): Take off immediately all
contaminated clothing. Rinse skin with water/shower. If inhaled: Remove person to fresh air and
keep comfortable for breathing. If in eyes: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing. Call a poison center/doctor if
you feel unwell. Rinse mouth. Do NOT induce vomiting. If skin irritation occurs: Get medical
advice/attention. If eye irritation persists: Get medical advice/attention. Take off contaminated
clothing and wash before reuse. In case of fire: Use appropriate media to extinguish.
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 1 / 10
Storage Store in a well-ventilated place. Keep container tightly closed. Keep cool. Store locked up.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise
classified (HNOC)
Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.
May form explosive peroxides. Contains a chemical classified by the US EPA as a suspected
possible carcinogen.
Supplemental information
Not applicable.
3. Composition/information on ingredients
Mixtures
67-64-1 25-40Acetone
CAS number %Chemical name
108-94-1 25-40Cyclohexanone
109-99-9 15-30Furan, Tetrahydro-
78-93-3 15-30Methyl ethyl ketone
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Inhalation
Take off immediately all contaminated clothing. Wash with plenty of soap and water. If skin
irritation occurs: Get medical advice/attention.
Skin contact
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
Eye contact
Call a physician or poison control center immediately. Do not induce vomiting. If vomiting occurs,
keep head low so that stomach content doesn't get into the lungs. Aspiration may cause
pulmonary edema and pneumonitis.
Ingestion
Irritation of nose and throat. Aspiration may cause pulmonary edema and pneumonitis. Severe eye
irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May
cause respiratory irritation. Vapors have a narcotic effect and may cause headache, fatigue,
dizziness and nausea. Skin irritation. May cause redness and pain.
Most important
symptoms/effects, acute and
delayed
Provide general supportive measures and treat symptomatically. Thermal burns: Flush with water
immediately. While flushing, remove clothes which do not adhere to affected area. Call an
ambulance. Continue flushing during transport to hospital. In case of shortness of breath, give
oxygen. Keep victim warm. Keep victim under observation. Symptoms may be delayed.
Indication of immediate
medical attention and special
treatment needed
Take off all contaminated clothing immediately. Ensure that medical personnel are aware of the
material(s) involved, and take precautions to protect themselves. Wash contaminated clothing
before reuse.
General information
5. Fire-fighting measures
Alcohol resistant foam. Water fog. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing media
Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing
media
Vapors may form explosive mixtures with air. Vapors may travel considerable distance to a source
of ignition and flash back. During fire, gases hazardous to health may be formed.
Specific hazards arising from
the chemical
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.Special protective equipment
and precautions for firefighters
In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do
so without risk.Fire fighting
equipment/instructions
Use standard firefighting procedures and consider the hazards of other involved materials.Specific methods
Highly flammable liquid and vapor. This product contains tetrahydrofuran that may form explosive
organic peroxide when exposed to air or light or with age.
General fire hazards
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 2 / 10
6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of
low areas. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area).
Wear appropriate protective equipment and clothing during clean-up. Avoid breathing mist or
vapor. Do not touch damaged containers or spilled material unless wearing appropriate protective
clothing. Ventilate closed spaces before entering them. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Take
precautionary measures against static discharge. Use only non-sparking tools. Keep combustibles
(wood, paper, oil, etc.) away from spilled material. This product is miscible in water.
Large Spills: Stop the flow of material, if this is without risk. Use water spray to reduce vapors or
divert vapor cloud drift. Dike the spilled material, where this is possible. Cover with plastic sheet to
prevent spreading. Use a non-combustible material like vermiculite, sand or earth to soak up the
product and place into a container for later disposal. Prevent entry into waterways, sewer,
basements or confined areas. Following product recovery, flush area with water.
Small Spills: Absorb with earth, sand or other non-combustible material and transfer to containers
for later disposal. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid discharge into drains, water courses or onto the ground.Environmental precautions
7. Handling and storage
Vapors may form explosive mixtures with air. Do not handle, store or open near an open flame,
sources of heat or sources of ignition. Protect material from direct sunlight. Explosion-proof
general and local exhaust ventilation. Take precautionary measures against static discharges. All
equipment used when handling the product must be grounded. Use non-sparking tools and
explosion-proof equipment. Avoid breathing mist or vapor. Avoid contact with eyes, skin, and
clothing. Avoid prolonged exposure. Do not taste or swallow. When using, do not eat, drink or
smoke. Wear appropriate personal protective equipment. Wash hands thoroughly after handling.
Observe good industrial hygiene practices.
Precautions for safe handling
Store locked up. Keep away from heat, sparks and open flame. Prevent electrostatic charge
build-up by using common bonding and grounding techniques. Store in a cool, dry place out of
direct sunlight. Store in original tightly closed container. Store in a well-ventilated place. Store
away from incompatible materials (see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueTypeComponents
PEL 2400 mg/m3Acetone (CAS 67-64-1)
1000 ppm
PEL 200 mg/m3Cyclohexanone (CAS
108-94-1)
50 ppm
PEL 590 mg/m3Furan, Tetrahydro- (CAS
109-99-9)
200 ppm
PEL 590 mg/m3Methyl ethyl ketone (CAS
78-93-3)
200 ppm
US. ACGIH Threshold Limit Values
ValueTypeComponents
STEL 750 ppmAcetone (CAS 67-64-1)
TWA 500 ppm
STEL 50 ppmCyclohexanone (CAS
108-94-1)
TWA 20 ppm
STEL 100 ppmFuran, Tetrahydro- (CAS
109-99-9)
Oatey Purple Primer- NSF Listed for PVC and CPVC SDS US
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 3 / 10
US. ACGIH Threshold Limit Values
ValueTypeComponents
TWA 50 ppm
STEL 300 ppmMethyl ethyl ketone (CAS
78-93-3)
TWA 200 ppm
US. NIOSH: Pocket Guide to Chemical Hazards
ValueTypeComponents
TWA 590 mg/m3Acetone (CAS 67-64-1)
250 ppm
TWA 100 mg/m3Cyclohexanone (CAS
108-94-1)
25 ppm
STEL 735 mg/m3Furan, Tetrahydro- (CAS
109-99-9)
250 ppm
TWA 590 mg/m3
200 ppm
STEL 885 mg/m3Methyl ethyl ketone (CAS
78-93-3)
300 ppm
TWA 590 mg/m3
200 ppm
Biological limit values
ACGIH Biological Exposure Indices
Value Sampling TimeDeterminant SpecimenComponents
50 mg/l Acetone Urine *Acetone (CAS 67-64-1)
80 mg/l 1,2-Cyclohexanediol,with
hydrolysis
Urine *Cyclohexanone (CAS
108-94-1)
8 mg/l Cyclohexanol,
with hydrolysis
Urine *
2 mg/l Tetrahydrofura
n
Urine *Furan, Tetrahydro- (CAS
109-99-9)
2 mg/l MEK Urine *Methyl ethyl ketone (CAS
78-93-3)
* - For sampling details, please see the source document.
Exposure guidelines
US - California OELs: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
US - Minnesota Haz Subs: Skin designation applies
Cyclohexanone (CAS 108-94-1)Skin designation applies.
US - Tennessee OELs: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
US ACGIH Threshold Limit Values: Skin designation
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
Furan, Tetrahydro- (CAS 109-99-9)Can be absorbed through the skin.
US. NIOSH: Pocket Guide to Chemical Hazards
Cyclohexanone (CAS 108-94-1)Can be absorbed through the skin.
Explosion-proof general and local exhaust ventilation. Good general ventilation (typically 10 air
changes per hour) should be used. Ventilation rates should be matched to conditions. If
applicable, use process enclosures, local exhaust ventilation, or other engineering controls to
maintain airborne levels below recommended exposure limits. If exposure limits have not been
established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency
shower must be available when handling this product.
Appropriate engineering
controls
Individual protection measures, such as personal protective equipment
Face shield is recommended. Wear safety glasses with side shields (or goggles).Eye/face protection
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 4 / 10
Skin protection
Wear appropriate chemical resistant gloves.Hand protection
Wear appropriate chemical resistant clothing.Other
If engineering controls do not maintain airborne concentrations below recommended exposure
limits (where applicable) or to an acceptable level (in countries where exposure limits have not
been established), an approved respirator must be worn.
Respiratory protection
Wear appropriate thermal protective clothing, when necessary.Thermal hazards
When using, do not eat, drink or smoke. Always observe good personal hygiene measures, such
as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash
work clothing and protective equipment to remove contaminants.
General hygiene
considerations
9. Physical and chemical properties
Appearance
Liquid.Physical state
Translucent liquid.Form
PurpleColor
Solvent.Odor
Odor threshold Not available.
pH Not available.
Melting point/freezing point Not available.
Initial boiling point and boiling
range
151 °F (66.11 °C)
Flash point 14.0 - 23.0 °F (-10.0 - -5.0 °C)
Evaporation rate 5.5 - 8
Not available.Flammability (solid, gas)
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
1.8
Flammability limit - upper
(%)
11.8
Explosive limit - lower (%)Not available.
Explosive limit - upper (%)Not available.
Vapor pressure 145 mm Hg @ 20 C
Vapor density 2.5
Relative density 0.84 +/- 0.02 @20°C
Solubility(ies)
Solubility (water)Negligible
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature Not available.
Decomposition temperature
Viscosity
Other information
Bulk density
VOC (Weight %)
10. Stability and reactivity
Reactivity
Chemical stability
Possibility of hazardous
reactions
Conditions to avoid
Not available.
Not available.
7 lb/gal
< 550 g/l SQACMD Method 24
The product is stable and non-reactive under normal conditions of use, storage and transport.
Material is stable under normal conditions.
No dangerous reaction known under conditions of normal use.
Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the
flash point. Contact with incompatible materials.
Acids. Strong oxidizing agents. Ammonia. Amines. Isocyanates. Caustics.Incompatible materials
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 5 / 10
No hazardous decomposition products are known.Hazardous decomposition
products
11. Toxicological information
Information on likely routes of exposure
Inhalation May be fatal if swallowed and enters airways. Headache. Nausea, vomiting. May cause irritation
to the respiratory system. Vapors have a narcotic effect and may cause headache, fatigue,
dizziness and nausea. Prolonged inhalation may be harmful.
Skin contact Causes skin irritation.
Eye contac Causes serious eye irritation.
Ingestion May be fatal if swallowed and enters airways. Harmful if swallowed. Harmful if swallowed. Droplets
of the product aspirated into the lungs through ingestion or vomiting may cause a serious
chemical pneumonia.
Symptoms related to the
physical, chemical and
toxicological characteristics
Irritation of nose and throat. Aspiration may cause pulmonary edema and pneumonitis. Severe
eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May
cause respiratory irritation. Skin irritation. May cause redness and pain. Symptoms of
overex osure ma be headache, dizziness, tiredness, nausea and vomitin .
Information on toxicological effects
Acute toxicit May be fatal if swallowed and enters airways. Narcotic effects. May cause respiratory irritation.
Test ResultsComponentsSpecies
Acetone (CAS 67-64-1)
LD50 Rabbit
Dermal
Acute
20 ml/kg
LC50 Rat
Inhalation
50 mg/l, 8 Hours
LD50 Rat
Oral
5800 mg/kg
Cyclohexanone (CAS 108-94-1)
LD50 Rabbit
Dermal
Acute
948 mg/kg
LC50 Rat
Inhalation
8000 ppm, 4 hours
LD50 Rat
Oral
1540 mg/kg
* Estimates for product may be based on additional component data not shown.
Causes skin irritation.Skin corrosion/irritation
Causes serious eye irritation.Serious eye damage/eye
irritation
Respiratory or skin sensitization
Respiratory sensitization Not available.
This product is not expected to cause skin sensitization.Skin sensitization
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Germ cell mutagenicity
Carcinogenicity In 2012 USEPA Integrated Risk Information System (IRIS) reviewed a two species inhalation
lifetime study on THF conducted by NTP (1998). Male rats developed renal tumors and female
mice developed liver tumors while neither the female rats nor the male mice showed similar
results. Because the carcinogenic mechanisms could not be identified clearly in either species for
either tumor, the EPA determined that the male rat and female mouse findings are relevant to the
assessment of carcinogenic potential in humans. Therefore, the IRIS review concludes that these
data in aggregate indicate that there is "suggestive evidence of carcinogenic potential" following
exposure to THF by all routes of exposure.
IARC Monographs. Overall Evaluation of Carcinogenicity
Cyclohexanone (CAS 108-94-1)3 Not classifiable as to carcinogenicity to humans.
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 6 / 10
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
This product is not expected to cause reproductive or developmental effects.Reproductive toxicity
Specific target organ toxicity -
single exposure
Narcotic effects. May cause drowsiness and dizziness. Respiratory tract irritation.
Specific target organ toxicity -
repeated exposure
Not classified.
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged inhalation may be harmful.
12. Ecological information
The product is not classified as environmentally hazardous. However, this does not exclude the
possibility that large or frequent spills can have a harmful or damaging effect on the environment.
Ecotoxicity
Components Test ResultsSpecies
Acetone (CAS 67-64-1)
Aquatic
LC50Fish > 100 mg/l, 96 hoursFathead minnow (Pimephales promelas)
* Estimates for product may be based on additional component data not shown.
Cyclohexanone (CAS 108-94-1)
Aquatic
LC50Fish 481 - 578 mg/l, 96 hoursFathead minnow (Pimephales promelas)
No data is available on the degradability of this product.Persistence and degradability
No data available.Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
Acetone (CAS 67-64-1)-0.24
Cyclohexanone (CAS 108-94-1)0.81
Furan, Tetrahydro- (CAS 109-99-9)0.46
Methyl ethyl ketone (CAS 78-93-3)0.29
No data available.Mobility in soil
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. This material
and its container must be disposed of as hazardous waste. Do not allow this material to drain into
sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Disposal instructions
Dispose in accordance with all applicable regulations.Local disposal regulations
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Hazardous waste code
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Waste from residues / unused
products
Empty containers should be taken to an approved waste handling site for recycling or disposal.
Since emptied containers may retain product residue, follow label warnings even after container is
emptied.
Contaminated packaging
14. Transport information
DOT
UN1993UN number
Flammable liquids, n.o.s. (Methyl ethyl ketone RQ = 26274 LBS, Acetone RQ = 13130 LBS)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
3Label(s)
IIPacking group
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 7 / 10
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
IB2, T7, TP1, TP8, TP28Special provisions
150Packaging exceptions
202Packaging non bulk
242Packaging bulk
IATA
UN1993UN number
Flammable liquid, n.o.s. (Methyl ethyl ketone, Acetone)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIPacking group
No.Environmental hazards
3HERG Code
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
IMDG
UN1993UN number
FLAMMABLE LIQUID, N.O.S. (Methyl ethyl ketone, Acetone)UN proper shipping name
3Class
Transport hazard class(es)
-Subsidiary risk
IIPacking group
No.Marine pollutant
Environmental hazards
F-E, S-EEmS
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
Not available.Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
15. Regulatory information
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
All components are on the U.S. EPA TSCA Inventory List.
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not listed.
CERCLA Hazardous Substance List (40 CFR 302.4)
Acetone (CAS 67-64-1)LISTED
Cyclohexanone (CAS 108-94-1)LISTED
Furan, Tetrahydro- (CAS 109-99-9)LISTED
Methyl ethyl ketone (CAS 78-93-3)LISTED
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
Hazard categories
SARA 302 Extremely hazardous substance
Not listed.
NoSARA 311/312 Hazardous
chemical
SARA 313 (TRI reporting)
Not regulated.
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 8 / 10
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Not regulated.Safe Drinking Water Act
(SDWA)
Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and
Chemical Code Number
Acetone (CAS 67-64-1) 6532
Methyl ethyl ketone (CAS 78-93-3) 6714
Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c))
Acetone (CAS 67-64-1) 35 %WV
Methyl ethyl ketone (CAS 78-93-3) 35 %WV
DEA Exempt Chemical Mixtures Code Number
Acetone (CAS 67-64-1) 6532
Methyl ethyl ketone (CAS 78-93-3) 6714
US state regulations
US. Massachusetts RTK - Substance List
Acetone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. New Jersey Worker and Community Right-to-Know Act
Acetone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. Pennsylvania Worker and Community Right-to-Know Law
Acetone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. Rhode Island RTK
Acetone (CAS 67-64-1)
Cyclohexanone (CAS 108-94-1)
Furan, Tetrahydro- (CAS 109-99-9)
Methyl ethyl ketone (CAS 78-93-3)
US. California Proposition 65
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain
any chemicals currently listed as carcinogens or reproductive toxins.
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Domestic Substances List (DSL) YesCanada
*A "Yes" indicates this product complies with the inventory requirements administered by the governing country(s).
"No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
Toxic Substances Control Act (TSCA) Inventory YesUnited States & Puerto Rico
16. Other information, including date of preparation or last revision
27-May-2015Issue date
-Revision date
Version #01
Health: 2
Flammability: 3
Physical hazard: 0
HMIS® ratings
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 9 / 10
NFPA ratings
02
3
The information in the sheet was written based on the best knowledge and experience currently
available. Oatey Co. cannot anticipate all conditions under which this information and its product,
or the products of other manufacturers in combination with its product, may be used. It is the
user’s responsibility to ensure safe conditions for handling, storage and disposal of the product,
and to assume liability for loss, injury, damage or expense due to improper use.
Disclaimer
SDS USOatey Purple Primer- NSF Listed for PVC and CPVC
926733 Version #: 01 Revision date: 12-5-2017 Issue date: 5-27-2015 10 / 10
Industrial Enamel
Pure White
Not available.
Liquid.
US / Canada: [phone]
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year
SAFETY DATA SHEET
Product name
Other means of
identification
Product type
Emergency telephone
number of the company
Section 1. Identification
:
:
:
:
Manufacturer :THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
B54W101
B54W101Product code :
Product Information
Telephone Number
:US / Canada: [phone]
Mexico: Not Available
Regulatory Information
Telephone Number
:US / Canada: [phone]
Mexico: Not Available
Transportation Emergency
Telephone Number
:US / Canada: [phone]
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year
Section 2. Hazards identification
FLAMMABLE LIQUIDS - Category 3
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1
ASPIRATION HAZARD - Category 1
Classification of the
substance or mixture
:
Hazard pictograms :
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 39.1%
(oral), 39.1% (dermal), 39.1% (inhalation)
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 1/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 2. Hazards identification
Signal word :Danger
Precautionary statements
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Use only outdoors or
in a well-ventilated area. Do not breathe vapor. Do not eat, drink or smoke when using
this product. Wash thoroughly after handling. Contaminated work clothing must not be
allowed out of the workplace.
Response :IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF SWALLOWED: Immediately call a POISON CENTER or
doctor. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all
contaminated clothing. Rinse skin with water. Wash contaminated clothing before
reuse. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get
medical advice or attention.
Storage :Store locked up. Store in a well-ventilated place. Keep container tightly closed. Keep
cool.
Disposal Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue
may spontaneously catch fire if improperly discarded. Immediately place rags, steel
wool, other waste soaked with this product, and sanding residue in a sealed, water-filled,
metal container. Dispose of in accordance with local fire regulations.
Flammable liquid and vapor.
May be fatal if swallowed and enters airways.
May cause an allergic skin reaction.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Suspected of causing cancer.
Suspected of damaging fertility or the unborn child.
Causes damage to organs through prolonged or repeated exposure. (lungs)
:Hazard statements
Please refer to the SDS for additional information. Keep out of reach of children. Do not
transfer contents to other containers for storage.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. FOR INDUSTRIAL USE ONLY.
:
Section 3. Composition/information on ingredients
Other means of
identification
:Not available.
Substance/mixture
CAS number/other identifiers
:Mixture
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 2/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 3. Composition/information on ingredients
Light Aliphatic Hydrocarbon ≥25 - ≤50 64742-47-8
Titanium Dioxide ≥10 - ≤25 13463-67-7
Talc ≤5 14807-96-6
Xylene, mixed isomers <1 1330-20-7
Hydrotreated Heavy Petroleum Naphtha <1 64742-48-9
Methyl Ethyl Ketoxime <1 96-29-7
Zirconium 2-Ethylhexanoate ≤1 22464-99-9
Med. Aliphatic Hydrocarbon Solvent ≤0.3 64742-88-7
Methyl Isobutyl Ketone ≤0.3 108-10-1
Ethylbenzene ≤0.3 100-41-4
Calcium 2-Ethylhexanoate ≤0.3 136-51-6
2-(2-Methoxyethoxy)-ethanol ≤0.3 111-77-3
Ingredient name CAS number% by weight
Occupational exposure limits, if available, are listed in Section 8.
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified and hence require reporting in this section.
Get medical attention immediately. Call a poison center or physician. Wash out mouth
with water. Remove dentures if any. If material has been swallowed and the exposed
person is conscious, give small quantities of water to drink. Stop if the exposed person
feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter
lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a collar,
tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or
dizziness. May cause respiratory irritation.
Skin contact :May cause an allergic skin reaction.
No known significant effects or critical hazards.:Eye contact
Potential acute health effects
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 3/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 4. First aid measures
Protection of first-aiders :No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways.
:Ingestion
Over-exposure signs/symptoms
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
Eye contact :No specific data.
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Section 5. Fire-fighting measures
Specific hazards arising
from the chemical
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion. The vapor/gas is heavier than air and will spread along the
ground. Vapors may accumulate in low or confined areas or travel a considerable
distance to a source of ignition and flash back.
Use dry chemical, CO₂, water spray (fog) or foam.
Extinguishing media
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 4/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
:
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill :
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders :If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Section 7. Handling and storage
Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure - obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not swallow. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless
adequately ventilated. Keep in the original container or an approved alternative made
from a compatible material, kept tightly closed when not in use. Store and use away
:
Precautions for safe handling
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 5/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.
:
:
from heat, sparks, open flame or any other ignition source. Use explosion-proof
electrical (ventilating, lighting and material handling) equipment. Use only non-sparking
tools. Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
Light Aliphatic Hydrocarbon 64742-47-8 ACGIH TLV (United States, 1/2021).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapor) 8 hours.
Titanium Dioxide 13463-67-7 ACGIH TLV (United States, 1/2021).
TWA: 10 mg/m³ 8 hours.
OSHA PEL (United States, 5/2018).
TWA: 15 mg/m³ 8 hours. Form: Total dust
Talc 14807-96-6 NIOSH REL (United States, 10/2020).
TWA: 2 mg/m³ 10 hours. Form: Respirable
fraction
ACGIH TLV (United States, 1/2021).
TWA: 2 mg/m³ 8 hours. Form: Respirable
fraction
Xylene, mixed isomers 1330-20-7 ACGIH TLV (United States, 1/2021).
TWA: 100 ppm 8 hours.
TWA: 434 mg/m³ 8 hours.
STEL: 150 ppm 15 minutes.
STEL: 651 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 435 mg/m³ 8 hours.
Hydrotreated Heavy Petroleum Naphtha 64742-48-9 None.
Methyl Ethyl Ketoxime 96-29-7 OARS WEEL (United States, 1/2021). Skin
sensitizer.
TWA: 10 ppm 8 hours.
Zirconium 2-Ethylhexanoate 22464-99-9 ACGIH TLV (United States, 1/2021).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
NIOSH REL (United States, 10/2020).
TWA: 5 mg/m³, (as Zr) 10 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits (OSHA United States)
CAS #
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 6/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
OSHA PEL (United States, 5/2018).
TWA: 5 mg/m³, (as Zr) 8 hours.
Med. Aliphatic Hydrocarbon Solvent 64742-88-7 OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 400 mg/m³ 8 hours.
Methyl Isobutyl Ketone 108-10-1 ACGIH TLV (United States, 1/2021).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
NIOSH REL (United States, 10/2020).
TWA: 50 ppm 10 hours.
TWA: 205 mg/m³ 10 hours.
STEL: 75 ppm 15 minutes.
STEL: 300 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 410 mg/m³ 8 hours.
Ethylbenzene 100-41-4 ACGIH TLV (United States, 1/2021).
TWA: 20 ppm 8 hours.
NIOSH REL (United States, 10/2020).
TWA: 100 ppm 10 hours.
TWA: 435 mg/m³ 10 hours.
STEL: 125 ppm 15 minutes.
STEL: 545 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 435 mg/m³ 8 hours.
Calcium 2-Ethylhexanoate 136-51-6 None.
2-(2-Methoxyethoxy)-ethanol 111-77-3 None.
Petroleum refining, hydrotreated light distillate 64742-47-8 CA British Columbia Provincial (Canada,
6/2021). Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
CA Alberta Provincial (Canada, 6/2018).
Absorbed through skin.
8 hrs OEL: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
CA Ontario Provincial (Canada, 6/2019).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
Titanium dioxide 13463-67-7 CA British Columbia Provincial (Canada,
6/2021).
TWA: 10 mg/m³ 8 hours. Form: Total dust
TWA: 3 mg/m³ 8 hours. Form: respirable
fraction
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 10 mg/m³ 8 hours. Form: Total dust.
CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 10 mg/m³ 8 hours.
CA Ontario Provincial (Canada, 6/2019).
TWA: 10 mg/m³ 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
Ingredient name Exposure limits
Occupational exposure limits (Canada)
CAS #
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 7/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
STEL: 20 mg/m³ 15 minutes.
TWA: 10 mg/m³ 8 hours.
talc (none asbestiform)14807-96-6 CA British Columbia Provincial (Canada,
6/2021).
TWA: 2 mg/m³ 8 hours. Form: Respirable
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 2 mg/m³ 8 hours. Form: Respirable
dust.
CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 2 mg/m³ 8 hours. Form:
Respirable particulate
CA Ontario Provincial (Canada, 6/2019).
TWA: 2 mg/m³ 8 hours. Form: Respirable
particulate matter.
TWA: 2 f/cc 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
TWA: 2 mg/m³ 8 hours. Form: respirable
fraction
Xylene 1330-20-7 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
15 min OEL: 651 mg/m³ 15 minutes.
15 min OEL: 150 ppm 15 minutes.
8 hrs OEL: 434 mg/m³ 8 hours.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 100 ppm 8 hours.
STEL: 150 ppm 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 100 ppm 8 hours.
TWAEV: 434 mg/m³ 8 hours.
STEV: 150 ppm 15 minutes.
STEV: 651 mg/m³ 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
2-Butoxyethanol 111-76-2 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 97 mg/m³ 8 hours.
8 hrs OEL: 20 ppm 8 hours.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 20 ppm 8 hours.
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 20 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 30 ppm 15 minutes.
TWA: 20 ppm 8 hours.
Methyl Ethyl Ketoxime 96-29-7 OARS WEEL (United States, 1/2021). Skin
sensitizer.
TWA: 10 ppm 8 hours.
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 8/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Zirconium 2-Ethylhexanoate 22464-99-9 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 5 mg/m³, (as Zr) 8 hours.
15 min OEL: 10 mg/m³, (as Zr) 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 5 mg/m³, (as Zr) 8 hours.
STEV: 10 mg/m³, (as Zr) 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
STEL: 10 mg/m³, (as Zr) 15 minutes.
TWA: 5 mg/m³, (as Zr) 8 hours.
Methyl isobutyl ketone 108-10-1 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 205 mg/m³ 8 hours.
8 hrs OEL: 50 ppm 8 hours.
15 min OEL: 75 ppm 15 minutes.
15 min OEL: 307 mg/m³ 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 20 ppm 8 hours.
STEV: 75 ppm 15 minutes.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 75 ppm 15 minutes.
TWA: 50 ppm 8 hours.
Ethylbenzene 100-41-4 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
8 hrs OEL: 434 mg/m³ 8 hours.
15 min OEL: 543 mg/m³ 15 minutes.
15 min OEL: 125 ppm 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 20 ppm 8 hours.
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 20 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 125 ppm 15 minutes.
TWA: 100 ppm 8 hours.
Occupational exposure limits (Mexico)
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 9/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: safety glasses with side-
shields.
Eye/face protection
Respiratory protection :
:
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Environmental exposure
controls
:
Light Aliphatic Hydrocarbon 64742-47-8 ACGIH TLV (United States, 1/2021).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapor) 8 hours.
Zirconium 2-Ethylhexanoate 22464-99-9 NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
Methyl Isobutyl Ketone 108-10-1 NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 50 ppm 8 hours.
STEL: 75 ppm 15 minutes.
Exposure limitsCAS #
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 10/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 9. Physical and chemical properties
Physical state
Melting point/freezing point
Vapor pressure
Relative density
Solubility
Liquid.
Not available.
1.05
5 [Air = 1]
Not available.
Not available.Odor
pH
Not available.Color
Evaporation rate 0.13 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 38°C (100.4°F) [Pensky-Martens Closed Cup]
Not applicable.
Not applicable.
Viscosity Kinematic (40°C (104°F)): <20.5 mm2/s (<20.5 cSt)
Not available.Odor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
:148°C (298.4°F)
:Not available.
:Lower: 1%
Upper: 6%
Decomposition temperature :Not available.
Heat of combustion :17.879 kJ/g
Aerosol product
Molecular weight :Not applicable.
Boiling point, initial boiling
point, and boiling range
Flammability
Lower and upper explosion
limit/flammability limit
Relative vapor density
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.
0.17 kPa (1.27 mm Hg)
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 11/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Acute toxicity
Xylene, mixed isomers LC50 Inhalation Gas.Rat 6700 ppm 4 hours
LD50 Oral Rat 4300 mg/kg -
Hydrotreated Heavy
Petroleum Naphtha
LC50 Inhalation Vapor Rat 8500 mg/m³4 hours
LD50 Oral Rat >6 g/kg -
Methyl Ethyl Ketoxime LD50 Oral Rat 930 mg/kg -
Zirconium 2-Ethylhexanoate LD50 Dermal Rabbit >5 g/kg -
LD50 Oral Rat >5 g/kg -
Methyl Isobutyl Ketone LD50 Oral Rat 2080 mg/kg -
Ethylbenzene LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Not available.
Mutagenicity
Not available.
Irritation/Corrosion
Titanium Dioxide Skin - Mild irritant Human -72 hours 300
ug I
-
Talc Skin - Mild irritant Human -72 hours 300
ug I
-
Xylene, mixed isomers Eyes - Mild irritant Rabbit -87 mg -
Eyes - Severe irritant Rabbit -24 hours 5
mg
-
Skin - Mild irritant Rat -8 hours 60 uL -
Skin - Moderate irritant Rabbit -24 hours 500
mg
-
Skin - Moderate irritant Rabbit -100 %-
Methyl Ethyl Ketoxime Eyes - Severe irritant Rabbit -100 uL -
Methyl Isobutyl Ketone Eyes - Moderate irritant Rabbit -24 hours 100
uL
-
Eyes - Severe irritant Rabbit -40 mg -
Skin - Mild irritant Rabbit -24 hours 500
mg
-
Ethylbenzene Eyes - Severe irritant Rabbit -500 mg -
Skin - Mild irritant Rabbit -24 hours 15
mg
-
2-(2-Methoxyethoxy)-ethanol Eyes - Mild irritant Rabbit -24 hours 500
mg
-
Eyes - Moderate irritant Rabbit -500 mg -
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Information on toxicological effects
Classification
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 12/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Light Aliphatic Hydrocarbon Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Xylene, mixed isomers Category 3 -Respiratory tract
irritation
Hydrotreated Heavy Petroleum Naphtha Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Methyl Ethyl Ketoxime Category 1 -upper respiratory
tract
Category 3 Narcotic effects
Med. Aliphatic Hydrocarbon Solvent Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Methyl Isobutyl Ketone Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Ethylbenzene Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
2-(2-Methoxyethoxy)-ethanol Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Name Category
Name Category
Light Aliphatic Hydrocarbon Category 2 --
Talc Category 1 inhalation lungs
Xylene, mixed isomers Category 2 --
Hydrotreated Heavy Petroleum Naphtha Category 2 --
Methyl Ethyl Ketoxime Category 2 -blood system
Med. Aliphatic Hydrocarbon Solvent Category 1 --
Methyl Isobutyl Ketone Category 2 --
Ethylbenzene Category 2 --
2-(2-Methoxyethoxy)-ethanol Category 2 --
Aspiration hazard
Route of
exposure
Target organs
Route of
exposure
Target organs
Titanium Dioxide -2B -
Talc -3 -
Xylene, mixed isomers -3 -
Methyl Isobutyl Ketone -2B -
Ethylbenzene -2B -
Product/ingredient name NTPIARCOSHA
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 13/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Name Result
Light Aliphatic Hydrocarbon ASPIRATION HAZARD - Category 1
Xylene, mixed isomers ASPIRATION HAZARD - Category 1
Hydrotreated Heavy Petroleum Naphtha ASPIRATION HAZARD - Category 1
Med. Aliphatic Hydrocarbon Solvent ASPIRATION HAZARD - Category 1
Ethylbenzene ASPIRATION HAZARD - Category 1
Information on the likely
routes of exposure
Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or
dizziness. May cause respiratory irritation.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways.
:Ingestion
Skin contact :May cause an allergic skin reaction.
No known significant effects or critical hazards.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
Eye contact :No specific data.
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
:Not available.
Potential acute health effects
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects :Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects :Not available.
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 14/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Not available.
Causes damage to organs through prolonged or repeated exposure. Once sensitized, a
severe allergic reaction may occur when subsequently exposed to very low levels.
General :
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
Suspected of damaging the unborn child.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :Suspected of damaging fertility.
Numerical measures of toxicity
Not available.
Acute toxicity estimates
Section 12. Ecological information
Bioaccumulative potential
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Xylene, mixed isomers --Readily
Methyl Isobutyl Ketone --Readily
Ethylbenzene --Readily
Toxicity
Light Aliphatic Hydrocarbon Acute LC50 2200 µg/l Fresh water Fish - Lepomis macrochirus 4 days
Titanium Dioxide Acute LC50 >1000000 µg/l Marine water Fish - Fundulus heteroclitus 96 hours
Xylene, mixed isomers Acute LC50 8500 µg/l Marine water Crustaceans - Palaemonetes
pugio
48 hours
Acute LC50 13400 µg/l Fresh water Fish - Pimephales promelas 96 hours
Methyl Ethyl Ketoxime Acute LC50 843000 µg/l Fresh water Fish - Pimephales promelas 96 hours
Methyl Isobutyl Ketone Acute LC50 505000 µg/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 78 mg/l Fresh water Daphnia - Daphnia magna 21 days
Chronic NOEC 168 mg/l Fresh water Fish - Pimephales promelas -
Embryo
33 days
Ethylbenzene Acute EC50 4900 µg/l Marine water Algae - Skeletonema costatum 72 hours
Acute EC50 7700 µg/l Marine water Algae - Skeletonema costatum 96 hours
Acute EC50 6.53 mg/l Marine water Crustaceans - Artemia sp. -
Nauplii
48 hours
Acute EC50 2.93 mg/l Fresh water Daphnia - Daphnia magna -
Neonate
48 hours
Acute LC50 4200 µg/l Fresh water Fish - Oncorhynchus mykiss 96 hours
2-(2-Methoxyethoxy)-ethanol Acute EC50 >930 ppm Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 7500000 µg/l Fresh water Fish - Lepomis macrochirus 96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 15/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 12. Ecological information
LogPow BCF Potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
Xylene, mixed isomers -8.1 to 25.9 low
Hydrotreated Heavy
Petroleum Naphtha
-10 to 2500 high
Methyl Ethyl Ketoxime -2.5 to 5.8 low
Zirconium 2-Ethylhexanoate -2.96 low
Calcium 2-Ethylhexanoate -2.96 low
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
PAINT
3
III
PAINT. Marine
pollutant (Light
Aliphatic
Hydrocarbon)
3
III
UN1263 UN1263
DOT
Classification
IMDG
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Environmental
hazards
No.Yes.
TDG
Classification
UN1263
PAINT
3
III
No.
Mexico
Classification
UN1263
PAINT
3
III
No.
IATA
UN1263
PAINT
3
III
Yes. The
environmentally
hazardous
substance mark
is not required.
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 16/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 14. Transport information
This product may
be re-classified as
"Combustible
Liquid," unless
transported by
vessel or aircraft.
Non-bulk
packages (less
than or equal to
119 gal) of
combustible
liquids are not
regulated as
hazardous
materials in
package sizes
less than the
product reportable
quantity.
The marine
pollutant mark is
not required when
transported in
sizes of ≤5 L or ≤5
kg.
Emergency
schedules F-E, S-
E
Additional
information
Special precautions for user
Transport in bulk according
to IMO instruments
Not available.
:
Proper shipping name :
Not available.
:
Product classified
as per the
following sections
of the
Transportation of
Dangerous Goods
Regulations:
2.18-2.19 (Class
3).
-
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability
prior to shipment, and compliance with the applicable regulations is the sole
responsibility of the person offering the product for transport. People loading and
unloading dangerous goods must be trained on all of the risks deriving from the
substances and on all actions in case of emergency situations.
The
environmentally
hazardous
substance mark
may appear if
required by other
transportation
regulations.
128
ERG No.
128 128
ERG No.ERG No.
Section 15. Regulatory information
SARA 313
SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
California Prop. 65
Australia inventory (AIIC): Not determined.
China inventory (IECSC): Not determined.
Japan inventory (CSCL): Not determined.
Japan inventory (ISHL): Not determined.
Korea inventory (KECI): Not determined.
New Zealand Inventory of Chemicals (NZIoC): Not determined.
Philippines inventory (PICCS): Not determined.
Taiwan Chemical Substances Inventory (TCSI): Not determined.
International regulations
International lists :
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 17/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 15. Regulatory information
Thailand inventory: Not determined.
Turkey inventory: Not determined.
Vietnam inventory: Not determined.
Section 16. Other information
7/19/2022
History
Date of printing
Date of issue/Date of
revision
Version
Date of previous issue
:
:
:
:
Indicates information that has changed from previously issued version.
Key to abbreviations :
7/19/2022
6/11/2022
29.01
Hazardous Material Information System (U.S.A.)
3
2
0
*Health
Flammability
Physical hazards
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS®
Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
FLAMMABLE LIQUIDS - Category 3 On basis of test data
SKIN SENSITIZATION - Category 1 Calculation method
CARCINOGENICITY - Category 2 Calculation method
TOXIC TO REPRODUCTION - Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 Calculation method
ASPIRATION HAZARD - Category 1 Calculation method
Procedure used to derive the classification
Classification Justification
Notice to reader
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 18/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed
by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,
or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements
are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The
conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user
should not use the product for any purpose other than the purpose shown in the applicable section of this SDS
without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of
sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs
obtained from any other source.
Date of issue/Date of revision :7/19/2022 Date of previous issue :6/11/2022 Version :29.01 19/19
B54W101 Industrial Enamel
Pure White
SHW-85-NA-GHS-US
PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
Not available.
Liquid.
US / Canada: [phone]
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year
SAFETY DATA SHEET
Product name
Other means of
identification
Product type
Emergency telephone
number of the company
Section 1. Identification
:
:
:
:
Manufacturer :THE SHERWIN-WILLIAMS COMPANY
101 W. Prospect Avenue
Cleveland, OH 44115
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
B54W151
B54W151Product code :
Product Information
Telephone Number
:US / Canada: [phone]
Mexico: Not Available
Regulatory Information
Telephone Number
:US / Canada: [phone]
Mexico: Not Available
Transportation Emergency
Telephone Number
:US / Canada: [phone]
Mexico: SETIQ 800-00-214-00 / 55-5559-1588 Available 24 hours and 365 days a year
Section 2. Hazards identification
FLAMMABLE LIQUIDS - Category 3
SKIN SENSITIZATION - Category 1
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2
ASPIRATION HAZARD - Category 1
Classification of the
substance or mixture
:
Hazard pictograms :
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 24.3%
(oral), 24.3% (dermal), 24.3% (inhalation)
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 1/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 2. Hazards identification
Signal word :Danger
Precautionary statements
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Use only outdoors or
in a well-ventilated area. Do not breathe vapor. Contaminated work clothing must not
be allowed out of the workplace.
Response :IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF SWALLOWED: Immediately call a POISON CENTER or
doctor. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all
contaminated clothing. Rinse skin with water. Wash contaminated clothing before
reuse. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get
medical advice or attention.
Storage :Store locked up. Store in a well-ventilated place. Keep container tightly closed. Keep
cool.
Disposal Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue
may spontaneously catch fire if improperly discarded. Immediately place rags, steel
wool, other waste soaked with this product, and sanding residue in a sealed, water-filled,
metal container. Dispose of in accordance with local fire regulations.
Flammable liquid and vapor.
May be fatal if swallowed and enters airways.
May cause an allergic skin reaction.
May cause respiratory irritation.
May cause drowsiness or dizziness.
Suspected of causing cancer.
Suspected of damaging fertility or the unborn child.
May cause damage to organs through prolonged or repeated exposure.
:Hazard statements
Please refer to the SDS for additional information. Keep out of reach of children. Do not
transfer contents to other containers for storage.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. FOR INDUSTRIAL USE ONLY.
:
Section 3. Composition/information on ingredients
Light Aliphatic Hydrocarbon ≥10 - ≤25 64742-47-8
Titanium Dioxide ≥10 - ≤25 13463-67-7
Xylene, mixed isomers <1 1330-20-7
Hydrotreated Heavy Petroleum Naphtha <1 64742-48-9
Methyl Ethyl Ketoxime <1 96-29-7
Methyl Isobutyl Ketone <1 108-10-1
Calcium 2-Ethylhexanoate ≤0.3 136-51-6
2-(2-Methoxyethoxy)-ethanol ≤0.3 111-77-3
Ingredient name CAS number% by weight
Other means of
identification
:Not available.
Substance/mixture
CAS number/other identifiers
:Mixture
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 2/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 3. Composition/information on ingredients
Zirconium 2-Ethylhexanoate ≤0.3 22464-99-9
Ethylbenzene ≤0.3 100-41-4
Med. Aliphatic Hydrocarbon Solvent ≤0.3 64742-88-7
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol ≤0.3 77-99-6
Occupational exposure limits, if available, are listed in Section 8.
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified and hence require reporting in this section.
Get medical attention immediately. Call a poison center or physician. Wash out mouth
with water. Remove dentures if any. If material has been swallowed and the exposed
person is conscious, give small quantities of water to drink. Stop if the exposed person
feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter
lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a collar,
tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or
dizziness. May cause respiratory irritation.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways.
:Ingestion
Skin contact :May cause an allergic skin reaction.
No known significant effects or critical hazards.:Eye contact
Over-exposure signs/symptoms
Eye contact :No specific data.
Potential acute health effects
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 3/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 4. First aid measures
Protection of first-aiders :No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Section 5. Fire-fighting measures
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion. The vapor/gas is heavier than air and will spread along the
ground. Vapors may accumulate in low or confined areas or travel a considerable
distance to a source of ignition and flash back.
Use dry chemical, CO₂, water spray (fog) or foam.
Extinguishing media
:
:
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 4/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
:
Special protective actions
for fire-fighters
:
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill :
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders :If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Section 7. Handling and storage
Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure - obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not swallow. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless
adequately ventilated. Keep in the original container or an approved alternative made
from a compatible material, kept tightly closed when not in use. Store and use away
from heat, sparks, open flame or any other ignition source. Use explosion-proof
electrical (ventilating, lighting and material handling) equipment. Use only non-sparking
tools. Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 5/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 7. Handling and storage
Advice on general
occupational hygiene
Conditions for safe storage,
including any
incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.
:
:
Light Aliphatic Hydrocarbon 64742-47-8 ACGIH TLV (United States, 1/2021).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapor) 8 hours.
Titanium Dioxide 13463-67-7 ACGIH TLV (United States, 1/2021).
TWA: 10 mg/m³ 8 hours.
OSHA PEL (United States, 5/2018).
TWA: 15 mg/m³ 8 hours. Form: Total dust
Xylene, mixed isomers 1330-20-7 ACGIH TLV (United States, 1/2021).
TWA: 100 ppm 8 hours.
TWA: 434 mg/m³ 8 hours.
STEL: 150 ppm 15 minutes.
STEL: 651 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 435 mg/m³ 8 hours.
Hydrotreated Heavy Petroleum Naphtha 64742-48-9 None.
Methyl Ethyl Ketoxime 96-29-7 OARS WEEL (United States, 1/2021). Skin
sensitizer.
TWA: 10 ppm 8 hours.
Methyl Isobutyl Ketone 108-10-1 ACGIH TLV (United States, 1/2021).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
NIOSH REL (United States, 10/2020).
TWA: 50 ppm 10 hours.
TWA: 205 mg/m³ 10 hours.
STEL: 75 ppm 15 minutes.
STEL: 300 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 410 mg/m³ 8 hours.
Calcium 2-Ethylhexanoate 136-51-6 None.
2-(2-Methoxyethoxy)-ethanol 111-77-3 None.
Zirconium 2-Ethylhexanoate 22464-99-9 ACGIH TLV (United States, 1/2021).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits (OSHA United States)
CAS #
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 6/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
NIOSH REL (United States, 10/2020).
TWA: 5 mg/m³, (as Zr) 10 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 5 mg/m³, (as Zr) 8 hours.
Ethylbenzene 100-41-4 ACGIH TLV (United States, 1/2021).
TWA: 20 ppm 8 hours.
NIOSH REL (United States, 10/2020).
TWA: 100 ppm 10 hours.
TWA: 435 mg/m³ 10 hours.
STEL: 125 ppm 15 minutes.
STEL: 545 mg/m³ 15 minutes.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 435 mg/m³ 8 hours.
Med. Aliphatic Hydrocarbon Solvent 64742-88-7 OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 400 mg/m³ 8 hours.
2-Ethyl-2-(hydroxymethyl)-1,3-propanediol 77-99-6 None.
Petroleum refining, hydrotreated light distillate 64742-47-8 CA British Columbia Provincial (Canada,
6/2021). Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
CA Alberta Provincial (Canada, 6/2018).
Absorbed through skin.
8 hrs OEL: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
CA Ontario Provincial (Canada, 6/2019).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapour) 8 hours.
Titanium dioxide 13463-67-7 CA British Columbia Provincial (Canada,
6/2021).
TWA: 10 mg/m³ 8 hours. Form: Total dust
TWA: 3 mg/m³ 8 hours. Form: respirable
fraction
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 10 mg/m³ 8 hours. Form: Total dust.
CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 10 mg/m³ 8 hours.
CA Ontario Provincial (Canada, 6/2019).
TWA: 10 mg/m³ 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 20 mg/m³ 15 minutes.
TWA: 10 mg/m³ 8 hours.
Xylene 1330-20-7 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
15 min OEL: 651 mg/m³ 15 minutes.
15 min OEL: 150 ppm 15 minutes.
8 hrs OEL: 434 mg/m³ 8 hours.
CA British Columbia Provincial (Canada,
6/2021).
Ingredient name Exposure limits
Occupational exposure limits (Canada)
CAS #
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 7/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
TWA: 100 ppm 8 hours.
STEL: 150 ppm 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 100 ppm 8 hours.
TWAEV: 434 mg/m³ 8 hours.
STEV: 150 ppm 15 minutes.
STEV: 651 mg/m³ 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 150 ppm 15 minutes.
TWA: 100 ppm 8 hours.
Methyl Ethyl Ketoxime 96-29-7 OARS WEEL (United States, 1/2021). Skin
sensitizer.
TWA: 10 ppm 8 hours.
Methyl isobutyl ketone 108-10-1 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 205 mg/m³ 8 hours.
8 hrs OEL: 50 ppm 8 hours.
15 min OEL: 75 ppm 15 minutes.
15 min OEL: 307 mg/m³ 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
STEL: 75 ppm 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 20 ppm 8 hours.
STEV: 75 ppm 15 minutes.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 75 ppm 15 minutes.
TWA: 50 ppm 8 hours.
Zirconium 2-Ethylhexanoate 22464-99-9 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 5 mg/m³, (as Zr) 8 hours.
15 min OEL: 10 mg/m³, (as Zr) 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 5 mg/m³, (as Zr) 8 hours.
STEV: 10 mg/m³, (as Zr) 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
STEL: 10 mg/m³, (as Zr) 15 minutes.
TWA: 5 mg/m³, (as Zr) 8 hours.
Ethylbenzene 100-41-4 CA Alberta Provincial (Canada, 6/2018).
8 hrs OEL: 100 ppm 8 hours.
8 hrs OEL: 434 mg/m³ 8 hours.
15 min OEL: 543 mg/m³ 15 minutes.
15 min OEL: 125 ppm 15 minutes.
CA British Columbia Provincial (Canada,
6/2021).
TWA: 20 ppm 8 hours.
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 8/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Hand protection Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: safety glasses with side-
shields.
Eye/face protection
:
:
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
CA Ontario Provincial (Canada, 6/2019).
TWA: 20 ppm 8 hours.
CA Quebec Provincial (Canada, 6/2021).
TWAEV: 20 ppm 8 hours.
CA Saskatchewan Provincial (Canada,
7/2013).
STEL: 125 ppm 15 minutes.
TWA: 100 ppm 8 hours.
Environmental exposure
controls
:
Light Aliphatic Hydrocarbon 64742-47-8 ACGIH TLV (United States, 1/2021).
Absorbed through skin.
TWA: 200 mg/m³, (as total hydrocarbon
vapor) 8 hours.
Methyl Isobutyl Ketone 108-10-1 NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 50 ppm 8 hours.
STEL: 75 ppm 15 minutes.
Zirconium 2-Ethylhexanoate 22464-99-9 NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 5 mg/m³, (as Zr) 8 hours.
STEL: 10 mg/m³, (as Zr) 15 minutes.
Exposure limits
Occupational exposure limits (Mexico)
CAS #
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 9/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Respiratory protection :
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point/freezing point
Vapor pressure
Relative density
Solubility
Liquid.
Not available.
1.18
5 [Air = 1]
Not available.
Not available.Odor
pH
Not available.Color
Evaporation rate 0.13 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 39°C (102.2°F) [Pensky-Martens Closed Cup]
Not applicable.
Not applicable.
Viscosity Kinematic (40°C (104°F)): <20.5 mm2/s (<20.5 cSt)
Not available.Odor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
:148°C (298.4°F)
:Not available.
:Lower: 1%
Upper: 6%
Decomposition temperature :Not available.
Heat of combustion :12.112 kJ/g
Aerosol product
Molecular weight :Not applicable.
Boiling point, initial boiling
point, and boiling range
Flammability
Lower and upper explosion
limit/flammability limit
Relative vapor density
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.
0.17 kPa (1.27 mm Hg)
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 10/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Xylene, mixed isomers LC50 Inhalation Gas.Rat 6700 ppm 4 hours
LD50 Oral Rat 4300 mg/kg -
Hydrotreated Heavy
Petroleum Naphtha
LC50 Inhalation Vapor Rat 8500 mg/m³4 hours
LD50 Oral Rat >6 g/kg -
Methyl Ethyl Ketoxime LD50 Oral Rat 930 mg/kg -
Methyl Isobutyl Ketone LD50 Oral Rat 2080 mg/kg -
Zirconium 2-Ethylhexanoate LD50 Dermal Rabbit >5 g/kg -
LD50 Oral Rat >5 g/kg -
Ethylbenzene LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
2-Ethyl-2-(hydroxymethyl)
-1,3-propanediol
LD50 Oral Rat 14000 mg/kg -
Product/ingredient name Result Species Dose Exposure
Irritation/Corrosion
Titanium Dioxide Skin - Mild irritant Human -72 hours 300
ug I
-
Xylene, mixed isomers Eyes - Mild irritant Rabbit -87 mg -
Eyes - Severe irritant Rabbit -24 hours 5
mg
-
Skin - Mild irritant Rat -8 hours 60 uL -
Skin - Moderate irritant Rabbit -24 hours 500
mg
-
Skin - Moderate irritant Rabbit -100 %-
Methyl Ethyl Ketoxime Eyes - Severe irritant Rabbit -100 uL -
Methyl Isobutyl Ketone Eyes - Moderate irritant Rabbit -24 hours 100
uL
-
Eyes - Severe irritant Rabbit -40 mg -
Skin - Mild irritant Rabbit -24 hours 500
mg
-
2-(2-Methoxyethoxy)-ethanol Eyes - Mild irritant Rabbit -24 hours 500 -
Product/ingredient name Result Score Exposure ObservationSpecies
Information on toxicological effects
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 11/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Carcinogenicity
Not available.
Mutagenicity
Not available.
Teratogenicity
Not available.
Reproductive toxicity
Not available.
mg
Eyes - Moderate irritant Rabbit -500 mg -
Ethylbenzene Eyes - Severe irritant Rabbit -500 mg -
Skin - Mild irritant Rabbit -24 hours 15
mg
-
Sensitization
Not available.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Light Aliphatic Hydrocarbon Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Xylene, mixed isomers Category 3 -Respiratory tract
irritation
Hydrotreated Heavy Petroleum Naphtha Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Methyl Ethyl Ketoxime Category 1 -upper respiratory
tract
Category 3 Narcotic effects
Methyl Isobutyl Ketone Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
2-(2-Methoxyethoxy)-ethanol Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Ethylbenzene Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Med. Aliphatic Hydrocarbon Solvent Category 3 -Respiratory tract
irritation
Category 3 Narcotic effects
Name Category Route of
exposure
Target organs
Classification
Titanium Dioxide -2B -
Xylene, mixed isomers -3 -
Methyl Isobutyl Ketone -2B -
Ethylbenzene -2B -
Product/ingredient name NTPIARCOSHA
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 12/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Name Category
Light Aliphatic Hydrocarbon Category 2 --
Xylene, mixed isomers Category 2 --
Hydrotreated Heavy Petroleum Naphtha Category 2 --
Methyl Ethyl Ketoxime Category 2 -blood system
Methyl Isobutyl Ketone Category 2 --
2-(2-Methoxyethoxy)-ethanol Category 2 --
Ethylbenzene Category 2 --
Med. Aliphatic Hydrocarbon Solvent Category 1 --
Aspiration hazard
Name Result
Light Aliphatic Hydrocarbon ASPIRATION HAZARD - Category 1
Xylene, mixed isomers ASPIRATION HAZARD - Category 1
Hydrotreated Heavy Petroleum Naphtha ASPIRATION HAZARD - Category 1
Ethylbenzene ASPIRATION HAZARD - Category 1
Med. Aliphatic Hydrocarbon Solvent ASPIRATION HAZARD - Category 1
Route of
exposure
Target organs
Information on the likely
routes of exposure
Inhalation :Can cause central nervous system (CNS) depression. May cause drowsiness or
dizziness. May cause respiratory irritation.
Can cause central nervous system (CNS) depression. May be fatal if swallowed and
enters airways.
:Ingestion
Skin contact :May cause an allergic skin reaction.
No known significant effects or critical hazards.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
respiratory tract irritation
coughing
nausea or vomiting
headache
drowsiness/fatigue
dizziness/vertigo
unconsciousness
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
Eye contact :No specific data.
:Not available.
Potential acute health effects
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 13/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 11. Toxicological information
Not available.
May cause damage to organs through prolonged or repeated exposure. Once
sensitized, a severe allergic reaction may occur when subsequently exposed to very low
levels.
General :
Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
Suspected of damaging the unborn child.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :Suspected of damaging fertility.
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Not available.
Acute toxicity estimates
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects :Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects :Not available.
Section 12. Ecological information
Toxicity
Light Aliphatic Hydrocarbon Acute LC50 2200 µg/l Fresh water Fish - Lepomis macrochirus 4 days
Titanium Dioxide Acute LC50 >1000000 µg/l Marine water Fish - Fundulus heteroclitus 96 hours
Xylene, mixed isomers Acute LC50 8500 µg/l Marine water Crustaceans - Palaemonetes
pugio
48 hours
Acute LC50 13400 µg/l Fresh water Fish - Pimephales promelas 96 hours
Methyl Ethyl Ketoxime Acute LC50 843000 µg/l Fresh water Fish - Pimephales promelas 96 hours
Methyl Isobutyl Ketone Acute LC50 505000 µg/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 78 mg/l Fresh water Daphnia - Daphnia magna 21 days
Chronic NOEC 168 mg/l Fresh water Fish - Pimephales promelas -
Embryo
33 days
2-(2-Methoxyethoxy)-ethanol Acute EC50 >930 ppm Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 7500000 µg/l Fresh water Fish - Lepomis macrochirus 96 hours
Ethylbenzene Acute EC50 4900 µg/l Marine water Algae - Skeletonema costatum 72 hours
Acute EC50 7700 µg/l Marine water Algae - Skeletonema costatum 96 hours
Acute EC50 6.53 mg/l Marine water Crustaceans - Artemia sp. -
Nauplii
48 hours
Acute EC50 2.93 mg/l Fresh water Daphnia - Daphnia magna -
Neonate
48 hours
Acute LC50 4200 µg/l Fresh water Fish - Oncorhynchus mykiss 96 hours
2-Ethyl-2-(hydroxymethyl)
-1,3-propanediol
Acute EC50 13000000 µg/l Fresh water Daphnia - Daphnia magna 48 hours
Product/ingredient name SpeciesResult Exposure
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 14/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
Xylene, mixed isomers -8.1 to 25.9 low
Hydrotreated Heavy
Petroleum Naphtha
-10 to 2500 high
Methyl Ethyl Ketoxime -2.5 to 5.8 low
Calcium 2-Ethylhexanoate -2.96 low
Zirconium 2-Ethylhexanoate -2.96 low
2-Ethyl-2-(hydroxymethyl)
-1,3-propanediol
-<1 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Xylene, mixed isomers --Readily
Methyl Isobutyl Ketone --Readily
Ethylbenzene --Readily
Acute LC50 14400000 µg/l Marine water Fish - Cyprinodon variegatus 96 hours
Persistence and degradability
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
PAINT PAINT
UN1263 UN1263
DOT
Classification
IMDG
UN number
UN proper
shipping name
TDG
Classification
UN1263
PAINT
Mexico
Classification
UN1263
PAINT
IATA
UN1263
PAINT
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 15/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 14. Transport information
3
III
3
III
This product may
be re-classified as
"Combustible
Liquid," unless
transported by
vessel or aircraft.
Non-bulk
packages (less
than or equal to
119 gal) of
combustible
liquids are not
regulated as
hazardous
materials in
package sizes
less than the
product reportable
quantity.
Emergency
schedules F-E, S-
E
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
Special precautions for user
Transport in bulk according
to IMO instruments
No.No.
Not available.
:
Proper shipping name :
Not available.
:
3
III
No.
Product classified
as per the
following sections
of the
Transportation of
Dangerous Goods
Regulations:
2.18-2.19 (Class
3).
3
III
No.
-
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability
prior to shipment, and compliance with the applicable regulations is the sole
responsibility of the person offering the product for transport. People loading and
unloading dangerous goods must be trained on all of the risks deriving from the
substances and on all actions in case of emergency situations.
3
III
No.
-
128
ERG No.
128 128
ERG No.ERG No.
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 16/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 15. Regulatory information
SARA 313
TSCA 5(a)2 proposed significant new use rules: 5-Chloro-2-methylisothiazolinone;
2-Methyl-4-isothiazolin-3-one
SARA 313 (40 CFR 372.45) supplier notification can be found on the Environmental Data Sheet.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
California Prop. 65
Australia inventory (AIIC): Not determined.
China inventory (IECSC): Not determined.
Japan inventory (CSCL): Not determined.
Japan inventory (ISHL): Not determined.
Korea inventory (KECI): Not determined.
New Zealand Inventory of Chemicals (NZIoC): Not determined.
Philippines inventory (PICCS): Not determined.
Taiwan Chemical Substances Inventory (TCSI): Not determined.
Thailand inventory: Not determined.
Turkey inventory: Not determined.
Vietnam inventory: Not determined.
International regulations
International lists :
Section 16. Other information
6/18/2022
History
Date of printing
Date of issue/Date of
revision
Date of previous issue
:
:
:
6/18/2022
4/14/2022
Hazardous Material Information System (U.S.A.)
3
2
0
*Health
Flammability
Physical hazards
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS®
Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
FLAMMABLE LIQUIDS - Category 3 On basis of test data
SKIN SENSITIZATION - Category 1 Calculation method
CARCINOGENICITY - Category 2 Calculation method
TOXIC TO REPRODUCTION - Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract
irritation) - Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Narcotic effects) -
Category 3
Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2 Calculation method
ASPIRATION HAZARD - Category 1 Calculation method
Procedure used to derive the classification
Classification Justification
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 17/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Section 16. Other information
Version
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed
by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,
or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements
are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The
conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user
should not use the product for any purpose other than the purpose shown in the applicable section of this SDS
without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of
sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs
obtained from any other source.
:
Indicates information that has changed from previously issued version.
Key to abbreviations :
24
Notice to reader
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
Date of issue/Date of revision :6/18/2022 Date of previous issue :4/14/2022 Version :24 18/18
B54W151 PRO INDUSTRIAL™ Urethane Alkyd Enamel
Extra White
SHW-85-NA-GHS-US
Pecora 895 NST Page 1 of 9 November 9, 2017
SAFETY DATA SHEET

1. PRODUCT IDENTIFICATION
IDENTIFICATION of the SUBSTANCE or PREPARATION
TRADE NAME (AS LABELED): Pecora 895 NST Non-Staining Technology™
PRODUCT DESCRIPTION: Structural Silicone Glazing &Weatherproofing Sealant
CHEMICAL NAME/CLASS: Silicone
OTHER MEANS OF IDENTIFICATION/SYNONYMS 895 NST
RELEVANT USE: Structural Silicone Glazing &Weatherproofing Sealant/Caulking Compound
USES ADVISED AGAINST: Other Than Relevant Use
COMPANY/UNDERTAKING IDENTIFICATION:
SUPPLIER/MANUFACTURER'S NAME: Pecora Corporation
ADDRESS: 165 Wambold Road, Harleysville, PA 19438
EMERGENCY PHONE: [phone] (CHEMTREC, 24-hours)
BUSINESS PHONE: [phone] (Mon–Fri, 8 AM–5 PM ET)

PREPARATION DATE: July 13, 2007
REVISION DATE: November 9, 2017
This product is sold for commercial use. This SDS has been developed to address safety concerns of those individuals working with bulk quantities of this material, as well as those of potential users of this
product in industrial/occupational settings. ALL United States Occupational Safety and Health Administration Standard (29 CFR 1910.1200), U.S. State equivalent Standards, Canadian WHMIS 2015 and the Global Harmonization required information is included in appropriate sections based on the Global Harmonization Standard format. This product has been classified in accordance with the hazard criteria of the
countries listed above and the SDS contains all the information required by the Canadian WHMIS 2015 [HPR-GHS] , the Global Harmonization Standard and OSHA 1910.120.
2. HAZARD IDENTIFICATION
GLOBAL HARMONIZATION LABELING AND CLASSIFICATION: Classified in accordance with Global Harmonization Standard
under U.S. OSHA Hazard Communication Standard, Canadian WHMIS HPR-GHS 2015
Classification: Reproductive Toxicity Cat. 2, Acute Oral Toxicity Cat. 5, Acute Dermal Toxicity Cat. 5, Eye Irritation Cat. 2A, Skin Irritation Cat. 2, Skin
Sensitization Cat. 1B, STOT (Blood Effects) RE Cat. 2, Aquatic Chronic Toxicity Cat. 3
Signal Word: Warning Hazard Statement Codes: H361f, H303 + H313, H319, H315, H317, H373, H413
Precautionary Statement Codes: P201, P202, P260, P264, P273, P280, P308 + P313, P305 + P351 + P338, P337 + P313, P302 + P352, P321, P333 +
P313, P362 + P364, P405, P501
Hazard Symbols/Pictogram: GHS07, GHS08

EMERGENCY OVERVIEW:
Physical Description: This product is a smooth paste with a slightly medicinal odor and comes in various colors, including Black, Tru-White, Aluminum
Stone, Translucent, Bronze and Clear.
Health Hazards: WARNING! Contains trace compound that may cause adverse effects on fertility (based on animal data). May cause eye, skin, and
respiratory tract irritation, especially if exposure is prolonged. May be harmful if ingested or in contact with skin. May cause skin sensitization in
susceptible individuals. Contains compound that may cause adverse effects to the blood system with repeated exposure. Contains a trace compound
(Crystalline Silica), a known human carcinogen by inhalation of particles. Contains a trace compound (Crystalline Silica), a known human
carcinogen by inhalation of particles. Contains a trace compound (Crystalline Silica), a known human carcinogen by inhalation of particles;
however, due to the form of this product, this hazard is expected to be negligible.
Flammability Hazard: This product is combustible and can ignite if exposed to high temperature for a prolonged period or to direct flame.
Reactivity Hazard: This product is not reactive.
Environmental Hazard: This product has not been tested for environmental impact. This product contains compounds that can cause chronic aquatic
toxicity.
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM (HMIS®)
Health 2* See Section 16 for definitions of ratings
0 = Minimal 3 = Serious
1 = Slight 4 = Severe
2 = Moderate * = Chronic
Flammability 1
Physical Hazard 0

HMIS® is a registered trademark of the National Paint and Coatings Association.
CANADIAN WHMIS (HPR-GHS) 2015 CLASSIFICATION AND SYMBOLS: See Section 16 for in Classification and Symbols under
HPR-GHS 2015.
U.S. OSHA REGULATORY STATUS: This product has a classification under the Global Harmonization Standard, as applied under
OSHA regulations, as given earlier in this Section. See Section 16 for full classification details.

Pecora 895 NST Page 2 of 9 November 9, 2017
3. COMPOSITION and INFORMATION ON INGREDIENTS

Chemical Name CAS # W/W% LABEL ELEMENTS GHS Classification under U.S. OSHA Hazard Communication Standard & Canadian WHMIS (HPR-GHS) 2015 Hazard Statement Codes
Proprietary Polydimethyl Siloxane 35.0-80.0 NOTIFIED CLASSIFICATION
Classification: Eye Irritation Cat. 2A
Hazard Statement Codes: H319
Calcium Carbonate (Natural)
Calcium Carbonate (synthetic)
1317-65-3
471-34-0 0.0-70.0 SELF CLASSIFICATION
Classification: Not Applicable
Organic Methyl Silane 0.0-8.0
NOTIFIED CLASSIFICATION
Classification: Skin Sensitization Cat. 1B, Eye Irritation Cat. 2A, STOT (Blood Effects) RE Cat. 2
Hazard Statement Codes: H317, H319, H373
Proprietary Mineral Spirits (contains less than
0.1% benzene) 0.0–6.0
HARMONISED CLASSIFICATION - ANNEX VI OF REGULATION (EC) NO 1272/2008 (CLP REGULATION)
Classification: Aspiration Hazard Cat. 1
Hazard Statement Codes: H304
ADDITIONAL SELF-CLASSIFICATION
Classification: Flammable Liquid Cat. 3, Skin Irritation Cat. 2, STOT (Central Nervous System) SE Cat. 3, Aquatic Chronic Cat. 2
Hazard Statement Codes: H226, H315, H336, H411
Proprietary Cyclosiloxane 0.0-4.0
HARMONISED CLASSIFICATION AND LABELLING (CLP00) Classification: Reproductive Toxicity Cat. 2, Aquatic Chronic Toxicity Cat. 4
Hazard Statement Codes: H361f, H413
ADDITIONAL SELF-CLASSIFICATION
Classification: Flammable Liquid Cat. 3, Acute Oral Toxicity Cat. 4, Acute Dermal Toxicity Cat. 4
Hazard Statement Codes: H226, H302 + H312
Proprietary Phenylated Ketoxomio Silane 0.0-3.0
NOTIFIED CLASSIFICATION
Classification: Skin Sensitization Cat. 1B Hazard Statement Codes: H317
ADDITIONAL MFG CLASSIFICATION Classification: STOT RE Cat. 2, Aquatic Chronic Toxicity Cat. 3 Hazard Statement Codes: H373, H412
Crystalline Silica Quartz 14808-60-7 0.0-0.1
SELF CLASSIFICATION
Classification: Carcinogenic Cat. 1B
Hazard Statement Codes: H350i
The following are pigments that can be in the product, depending on coloration:
Carbon Black 13463-67-7 0.0-5.0
SELF-CLASSIFICATION
Classification: Carcinogenic Cat. 2
Hazard Statement Codes: H351i
Other trace components. Each of the other
components is present in less than 1 percent
concentration (0.1% concentration for potential
carcinogens, reproductive toxins, respiratory tract
sensitizers, and mutagens).
Balance Classification: Not Applicable
The specific chemical identity and/or exact percentage (concentration) of composition has been withheld as a trade secret.

4. FIRST-AID MEASURES
PROTECTION OF FIRST AID RESPONDERS: Rescuers should not attempt to retrieve victims of exposure to this product without
adequate personal protective equipment. Rescuers should be taken for medical attention, if necessary.
DESCRIPTION OF FIRST AID MEASURES: Remove victim(s) to fresh air, as quickly as possible. Only trained personnel should
administer supplemental oxygen and/or cardio-pulmonary resuscitation, if necessary. Remove and isolate contaminated clothing and
shoes. Seek medical attention if adverse effects occur after decontamination efforts or if contaminated individual is not breathing or
unconscious. Take copy of label and SDS to physician or other health professional with victim(s).
Inhalation: If aerosols from the product are inhaled, contaminated individual to fresh air. If necessary, use artificial respiration to support vital functions.
Seek medical attention if adverse effects occur/continue after removal to fresh air.
Skin Exposure: If the product contaminates the skin, immediately begin decontamination with running water. Minimum flushing is for 20 minutes. Do
not interrupt flushing. Remove exposed or contaminated clothing, taking care not to contaminate eyes. Contaminated individual must seek immediate
medical attention if adverse effect continues after flushing.
Eye Exposure: If this product enters the eyes, open contaminated eyes while under gently running water. Use sufficient force to open eyelids. Have
individual "roll" eyes. Minimum flushing is for 20 minutes. Do not interrupt flushing. Seek medical attention if adverse effect continues after flushing.
Ingestion: If this product is swallowed, CALL PHYSICIAN OR POISON CONTROL CENTER FOR MOST CURRENT INFORMATION. DO NOT
INDUCE VOMITING, unless directly by medical personnel. Have victim rinse mouth with water or give several cupfuls of water, if conscious. Never
induce vomiting or give diluents (milk or water) to someone who is unconscious, having convulsions, or unable to swallow. If vomiting occurs, lean
patient forward or place on left side (head-down position, if possible) to maintain an open airway and prevent aspiration.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Dermatitis or other pre-existing skin disorders may be aggravated by
exposure to this product.
INDICATION OF IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT IF NEEDED: Treat symptoms and eliminate
exposure. Persons suffering allergic reactions must seek immediate medical attention.

Pecora 895 NST Page 3 of 9 November 9, 2017

5. FIRE-FIGHTING MEASURES
FLASH POINT: > 140°C (> 300°F) AUTOIGNITION: Unknown.
FLAMMABLE LIMITS IN AIR: Unknown.
EXTINGUISHING MEDIA:
Suitable Extinguishing Media: Use extinguishing material suitable to the surrounding fire,
including foam, halon, carbon dioxide and dry chemical.
Unsuitable Extinguishing Media: None known.
PROTECTION OF FIREFIGHTERS:
Special Hazards Arising from the Product: This product is combustible and can be ignited when
exposed to its flashpoint. Not sensitive to mechanical impact under normal conditions. Not
sensitive to static discharge under normal conditions. Closed containers may develop
pressure and rupture in event of fire.
SPECIAL PROTECTIVE ACTIONS FOR FIRE-FIGHTERS: Incipient fire responders
should wear eye protection. Structural firefighters must wear Self-Contained
Breathing Apparatus and full protective equipment. Move containers from fire area
if it can be done without risk to personnel. If possible, prevent runoff water from
entering storm drains, bodies of water, or other environmentally sensitive areas.

6. ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS AND EMERGENCY PROCEDURES: An accidental release may result in a fire in the presence of an
ignition source. Uncontrolled releases should be responded to by trained personnel using pre-planned procedures. Proper protective
equipment should be used. Eliminate any possible sources of ignition, and provide maximum explosion-proof ventilation. Use only non-
sparking tools and equipment during the response. The atmosphere must at least 19.5 percent Oxygen before non-emergency personnel
can be allowed in the area without Self-Contained Breathing Apparatus and fire protection.
PERSONAL PROTECTIVE EQUIPMENT: Responders should wear the level of protection appropriate to the type of chemical released,
the amount of the material spilled, and the location where the incident has occurred.
Small Spills: For releases of 1 drum or less, Level D Protective Equipment (gloves, chemical resistant apron, boots, and eye protection) should be worn.
Large Spills: Minimum Personal Protective Equipment should be rubber gloves, rubber boots, face shield, and Tyvek suit. Minimum level of personal
protective equipment for releases in which the level of oxygen is less than 19.5% or is unknown must be Level B: triple-gloves (rubber gloves
and nitrile gloves over latex gloves), chemical resistant suit, fire-retardant clothing and boots, hard hat, and Self-Contained Breathing
Apparatus.
METHODS FOR CLEAN-UP AND CONTAINMENT:
All Spills: Access to the spill area should be restricted. Spread should be limited by gently covering the spill with polypads. Scrape up or pick-up
spilled material, placing in suitable containers. Absorb any residual on appropriate material, such as sand. All contaminated absorbents and other
materials should be placed in an appropriate container and seal. Do not mix with wastes from other materials. Dispose of in accordance with applicable
Federal, State, and local procedures (see Section 13, Disposal Considerations). Dispose of recovered material and report spill per regulatory
requirements. Remove all residue before decontamination of spill area. Clean spill area with soap and copious amounts of water.
ENVIRONMENTAL PRECAUTIONS: Minimize use of water to prevent environmental contamination. Prevent spill or rinsate from
contaminating storm drains, sewers, soil or groundwater. Place all spill residues in a suitable container and seal. Do not discharge
effluent containing this product into streams, ponds, estuaries, oceans or other waters unless in accordance with the requirements of a
National Pollutant Discharge Elimination System (NPDES) permit and the permitting authority has been notified in writing prior to
discharge. Do not discharge effluent containing this product to sewer systems without previously notifying the local sewage treatment
plant authority. For guidance, contact your State Water Board or Regional Office of the EPA.
OTHER INFORMATION: U.S. regulations may require reporting of spills of this material that reach surface waters if a sheen is formed.
If necessary, the toll-free phone number for the US Coast Guard National Response Center is 1-800-424-8802.
REFERENCE TO OTHER SECTIONS: See information in Section 8 (Exposure Controls – Personal Protection) and Section 13 (Disposal
Considerations) for additional information.

7. HANDLING and STORAGE
PRECAUTIONS FOR SAFE HANDLING: As with all chemicals, avoid getting this product ON YOU or IN YOU. Wash thoroughly
after handling this product. Do not eat or drink while handling this material. Avoid contact with eyes, skin, and clothing. Avoid
breathing fumes, dusts, vapors or mist. Do not taste or swallow. Use only with adequate ventilation. Keep away from heat and flame.
In the event of a spill, follow practices indicated in Section 6: ACCIDENTAL RELEASE MEASURES.
CONDITIONS FOR SAFE STORAGE: This product is stable under ordinary conditions of handling, use and storage. Store containers in
a cool, dry location, away from direct sunlight, sources of intense heat, or where freezing is possible. Store away from incompatible
materials (see Section 10: STABILITY AND REACTIVITY). Keep container tightly closed when not in use. Inspect all incoming
containers before storage, to ensure containers are properly labeled and not damaged. To prolong shelf life, store at temperatures below
26°C (80°F).
PRODUCT END USE: This product is used as a silicone sealant. Follow all industry standards for use of this product.

2 HEALTH
FLAMMABILITY

INSTABILITY
OTHER
See Section 16 for
Definitions of Ratings
NFPA RATING

1
0
Pecora 895 NST Page 4 of 9 November 9, 2017

8. EXPOSURE CONTROLS - PERSONAL PROTECTION
EXPOSURE LIMITS/CONTROL PARAMETERS:
Ventilation and Engineering Controls: Use with adequate ventilation to ensure exposure levels are maintained below the limits provided below.
Occupational/Workplace Exposure Limits/Guidelines:
Chemical Name CAS # Guideline Value
Calcium Carbonate, Natural
Calcium Carbonate, Synthetic
1317-65-3
471-34-0
OSHA PEL TWA

NIOSH REL TWA
15 mg/m3 total dust
5 mg/m3 respirable fraction
10 mg/m3 total dust
5 mg/m3 respirable fraction
Carbon Black 1333-86-4 ACGIH TLV TWA
OSHA PEL TWA
NIOSH REL TWA
DFG MAK TWA
3 mg/m3 (inhalable fraction)
3.5 mg/m3
3.5 mg/m3 (0.1 in the presence of PAHs, as PAHs: 10-hr TWA); See ACGIH
Pocket Guide Appendices A and C
As inhalable dust
Crystalline Silica (Quartz) 14808-60-7 ACGIH TLV TWA
OSHA PEL TWA
NIOSH REL TWA
0.025 mg/m3 respirable fraction
30 mg/m3 / % Sio2 + 2 total dust; 10 mg/m3 / % Sio2 + 2 respirable dust
0.05 mg/m3 respirable dust, See ACGIH Pocket Guide Appendix A
Organic Methyl Silane NE NE
Proprietary Cyclosiloxane NE NE
Proprietary Phenylated Ketoxomio Silane
Exposure limits given are for decomposition product methylethyl
ketoxime
AIHA WEEL TWA
DFG MAK TWA
10 ppm (Dermal Sensitizer)
Skin, Danger of Sensitization of the Skin
Proprietary Polydimethyl Siloxane NE NE
Proprietary Fumed Silicon Dioxide NE NE
Proprietary Mineral Spirits
Exposure limits given are for Mineral Spirits CAS # 8052-41-3
ACGIH TLV TWA
OSHA PEL TWA
NIOSH REL TWA
NIOSH REL STEL
525 mg/m3
2900 mg/m3
350 mg/m3
1800 mg/m3 (15 min.)
The following are exposure limits for a possible decomposition product, Methanol.
Methanol 67-56-1 ACGIH TLV TWA ACGIH TLV STEL OSHA PEL TWA OSHA PEL STEL
NIOSH REL TWA
NIOSH REL STEL
NIOSH IDLH
DFG MAK TWA
DFG MAK PEAK
DFG MAK Pregnancy Risk
200 ppm (skin) 250 ppm (skin) 200 ppm Vacated 1989 PEL: 250 ppm (skin)
200 (skin)
250 (skin)
6000 ppm
200 ppm (skin)
2 ●MAK 15 min. average value, 15 min. interval, 4-per shift
Classification C
NE = Not Established. See Section 16 for Definitions of Terms Used. Biological Exposure Indices (BEIs): Currently, no BEI’s have been established for components of this product.
PERSONAL PROTECTIVE EQUIPMENT (PPE): The following information on appropriate Personal Protective Equipment is
provided to assist employers in complying with OSHA regulations found in 29 CFR Subpart I (beginning at 1910.132, including the
Respiratory Protection Standard (29 CFR 1910.134), Eye Protection Standard 29 CFR 1910.13, the Hand Protection Standard 29 CFR
1910.138, and the Foot Protection Standard 29 CFR 1910.136), equivalent standards of Canada (including the Canadian CSA
Respiratory Standard Z94.4-93-02, the CSA Eye Protection Standard Z94.3-M1982, Industrial Eye and Face Protectors and the
Canadian CSA Foot Protection Standard Z195-M1984, Protective Footwear). Please reference applicable regulations and standards
for relevant details.
Eye/Face Protection: Use approved safety goggles or safety glasses. If necessary, refer to appropriate regulations and standards.
Skin Protection: Wear chemical impervious gloves (e.g., Nitrile or Neoprene). Use triple gloves for spill response. If necessary, refer to appropriate
regulations and standards.
Body Protection: Use body protection appropriate for task (e.g., lab coat, coveralls, Tyvek suit). If necessary, refer to the OSHA Technical Manual
(Section VII: Personal Protective Equipment) or appropriate Standards of Canada. If a hazard of injury to the feet exists due to falling objects, rolling
objects, where objects may pierce the soles of the feet or where employee’s feet may be exposed to electrical hazards, use foot protection, as described
in appropriate regulations and standards.
Respiratory Protection: If mists or sprays from this product are created during use, use appropriate respiratory protection. If necessary, use only
respiratory protection authorized in appropriate regulations. Oxygen levels below 19.5% are considered IDLH by OSHA. In such atmospheres, use
of a full-facepiece pressure/demand SCBA or a full facepiece, supplied air respirator with auxiliary self-contained air supply is required under
appropriate regulations and standards.

9. PHYSICAL and CHEMICAL PROPERTIES
FORM: Smooth paste. COLORS: Black, Tru-White, Aluminum Stone, Translucent, Bronze, Clear
MOLECULAR WEIGHT: Mixture. MOLECULAR FORMULA: Mixture.
ODOR: Mildly medicinal. ODOR THRESHOLD: Not available.
SPECIFIC GRAVITY: 1.1-1.4 VAPOR PRESSURE, mm Hg @ 20°C: Not established.
RELATIVE VAPOR DENSITY (air = 1): Heavier than air. EVAPORATION RATE (BuAc = 1): < 1
SOLUBILITY IN WATER: Insoluble. OTHER SOLUBILITIES: Not available.
MELTING/FREEZING POINT: Not available. BOILING POINT: Not established.
VOC (less water and exempt): < 100 g/L WEIGHT % VOC: ~ 10%
FLASH POINT: > 140°C (> 300°F) AUTOIGNITION TEMPERATURE: Not established.
FLAMMABLE LIMITS (in air by volume, %): Lower: Not established; Upper: Not established.

Pecora 895 NST Page 5 of 9 November 9, 2017

9. PHYSICAL and CHEMICAL PROPERTIES (Continued)
pH: Not available.
COEFFICIENT OF OIL/WATER DISTRIBUTION (PARTITION COEFFICIENT): Not established.
HOW TO DETECT THIS SUBSTANCE (IDENTIFYING PROPERTIES): The appearance of this product may act as an identifying
property in the event of an accidental release.

10. STABILITY and REACTIVITY
CHEMICAL STABILITY: Stable under normal circumstances of use and handling. Methylethyl Ketoxime is generated during curing.
Methanol can be generated from curing and contact with water.
CONDITIONS TO AVOID: Avoid contact with incompatible chemicals and exposure to extreme temperatures.
INCOMPATIBLE MATERIALS: This product is not compatible with strong acids and oxidizers and may have some compatibility with
aluminum, ammonium salts and mercury/hydrogen mixtures.
HAZARDOUS DECOMPOSITION PRODUCTS: Combustion: Thermal decomposition of this product can generate dusts, irritating
fumes, and toxic gases (e.g., carbon, nitrogen and silicone oxides, formaldehyde, various hydrocarbons). Hydrolysis: Methylethyl
ketoxime, methanol.
POSSIBILITY OF HAZARDOUS REACTIONS/POLYMERIZATION: This product is not expected to undergo hazardous
polymerization, decomposition, condensation, or self-reactivity.

11. TOXICOLOGICAL INFORMATION
POTENTIAL HEALTH EFFECTS: The most significant routes of occupational exposure are inhalation and contact with skin and eyes.
The symptoms of exposure to this product are as follows:
Contact with Skin or Eyes: Contact may irritate the skin and cause redness and discomfort, depending on duration of contact. Prolonged or repeated
skin contact may cause dermatitis (dry, red skin). Eye contact may cause redness, pain, and tearing. Skin contact may cause sensitization and allergic
reaction in susceptible individuals. Symptoms may include redness, itching and rash.
Skin Absorption: Some components of this product are known to be absorbed through intact skin. Skin contact may cause some systemic effects if a
large area of skin is contaminated.
Ingestion: If the product is swallowed, it may mildly irritate the mouth, throat, and other tissues of the gastro-intestinal system and may cause nausea,
vomiting, and diarrhea. Due to the Organic Methyl Silane component, ingestion may produce blood effects, reducing the blood’s ability to transport
oxygen (methemoglobinemia and anemia). Reversible narcotic effects may occur.
Inhalation: Exposure to vapors of this product generated during curing, or dusts of this product generated during use after curing may mildly irritate the
respiratory tract and cause coughing and sneezing. Vapors or fumes when used in an enclosed space, if heated or during curing may cause irritation of
the respiratory system. Symptoms include nose irritation, dry or sore or burning throat, runny nose, shortness of breath, dizziness, incoordination.
Vapors from decomposition or exposure to atmospheric moisture may produce reversible narcotic effect due to formation of methanol. Narcotic
effects can include dizziness, headache, nausea, vomiting, chest tightness, limb weakness, staggering gait, confusion. In severe cases, there may be
restlessness, convulsions, coma.
Injection: Accidental injection of this product (e.g. puncture with a contaminated object) may cause burning, redness, and swelling in addition to the
wound.
Target Organs: Acute: Skin, eyes. Chronic: Skin, blood.
Chronic Effects: Prolonged or repeated skin contact may cause dermatitis (dry, red skin).
TOXICITY DATA: There are currently no toxicity data available for this product; the following toxicology information is available for
components greater than 1% in concentration. Due to large amount of data for some components, only Human data, Irritancy data, LD50
Oral-Rat, LD50 Oral-Mouse, LD50 Skin-Rat, LD50 Skin-Rabbit, LC50 Inhalation-Rat, LC50 Inhalation-Mouse and select reproductive
toxicity data are provided in this SDS for those components. Contact Pecora for information on additional data.
CALCIUM CARBONATE, NATURAL:
TDLo (Intravenous-Rat) 30 mg/kg: Vascular: BP lowering not characterized in autonomic section; Lungs, Thorax, or Respiration: changes in lung weight; Blood: other changes
TCLo (Inhalation-Rat) 84 mg/m3/4 hours/40 weeks-intermittent: Lungs, Thorax, or Respiration: fibrosis (interstitial); Liver: other changes; Kidney/Ureter/Bladder: other changes
TCLo (Inhalation-Rat) 250 mg/m3/2 hours/24 weeks-intermittent: Lungs, Thorax, or Respiration: fibrosis, focal (pneumoconiosis)
CARBON BLACK: LD50 (Oral-Rat) > 15 400 mg/kg: Behavioral: somnolence (general depressed activity)
LD50 (Skin-Rabbit) > 3 gm/kg PROPRIETARY FUMED SILICA:
LD50 (Oral-Rat) 3160 mg/kg MINERAL SPIRITS:
Standard Draize Test (Eye-Human) 100 ppm: Mild
Standard Draize Test (Eye-Rabbit) 500 mg/24 hours: Moderate
LC50 (Inhalation-Rat) > 1400 ppm/8 hours
LD (Oral-Rat) > 5 gm/kg: Behavioral: somnolence (general depressed activity)
LD (Skin-Rabbit) > 3 gm/kg
LC (Inhalation-Rat) > 5500 mg/m3/4 hours: Behavioral: somnolence (general depressed activity)
PROPRIETARY CYCLOSIOLXANE:
Standard Draize Test (Skin-Rabbit) 500 mg/24 hours: Mild Standard Draize Test (Eye-Rabbit) 500 mg/24 hours: Mild
LC50 (Inhalation-Rat) 36 gm/m3/4 hours: Behavioral: excitement; Lungs, Thorax, or Respiration: dyspnea Skin and Appendages: hair
LD50 (Oral-Rat) 1540 mg/kg: Behavioral: tremor LD50 (Skin-Rat) 1770 mg/kg: Behavioral: tremor; Gastrointestinal: changes in structure or function
of salivary glands; Liver: other changes LD50 (Skin-Rabbit) 794 µL/kg: Kidney/Ureter/Bladder: hematuria
PROPRIETARY PHENYLATED KETOXIMO SILANE: LD50 (Oral-Rat) > 8000 mg/kg
LD50 (Dermal-Rat) > 4000 mg/kg LC50 (Inhalation-Rat) > 8000 mg/m3, 4 hours
PROPRIETARY POLYMDIMETHYLSILOXANE DIOL: LD50 (Oral-Rat) 3160 mg/kg

CARCINOGENIC POTENTIAL: The following table summarizes the carcinogenicity listing for the components of this product. “NO”
indicates that the substance is not considered to be or suspected to be a carcinogen by the listed agency, see section 16 for definitions
of other ratings.
CHEMICAL EPA IARC NTP NIOSH ACGIH OSHA MAK PROP 65
Calcium Carbonate (Natural, Synthetic) No No No No No No No No
Carbon Black No 2B No Ca (in presence
of PAHs)
A3 No No Yes (airborne, unbound particles
of respirable size)

Pecora 895 NST Page 6 of 9 November 9, 2017

11. TOXICOLOGICAL INFORMATION (Continued)
CARCINOGENIC POTENTIAL (continued):
CHEMICAL EPA IARC NTP NIOSH ACGIH OSHA MAK PROP 65
Crystalline Silica (quartz) No 1 K* Ca A2 No 1* Yes (airborne unbound
particles of respirable size)
Organic Methyl Silane No No No No No No No No
Mineral Spirits No No No No No No No No
Proprietary Cyclosiloxane No No No No No No No No
Proprietary Phenylated Ketoxomio Silane No No No No No No No No
Proprietary Polydimethyl Siloxane No No No No No No No No
Proprietary Fumed Silicon Dioxide No No No No No No No No
The following is a compound from reaction with water and generated during curing:
Methyl Alcohol No No No No No No No No
Methyl Ethyl Ketoxime No No No No No No No No
*Respirable. ACGIH TLV-A2: Suspected Human Carcinogen. ACGIH TLV-A3: Confirmed Animal Carcinogen with Unknown Relevance to Humans. IARC 1: Carcinogenic to Humans.
IARC-2B: Possibly Carcinogenic to Humans. MAK-1 Substances that Cause Cancer in Man and Can Be Assumed to Make a Significant Contribution to Cancer Risk. NTP-K: Known to Be a
Human Carcinogen. NIOSH-Ca: Potential Occupational Carcinogen, with No Further Categorization.
IRRITANCY OF PRODUCT: This product may irritate contaminated tissue, especially if contact is prolonged.
SENSITIZATION TO THE PRODUCT: This product may cause skin sensitization and allergic reaction in susceptible individuals due to
the Proprietary Phenylated Ketoximo Silane and Organic Methyl Silane components.
TOXICOLOGICAL SYNERGISTIC PRODUCTS: None known.
REPRODUCTIVE TOXICITY INFORMATION: This product has not been tested for reproductive toxicity. Information for some
components is given, as follows.
Mutagenicity/Embryotoxicity/ Teratogenicity/Reproductive Toxicity: In a developmental and reproductive toxicity study involving female rats and the
trace Proprietary Cyclosiloxane component, a significant percentage of female rats exposed experienced reduction of proestrus LH levels, a reduction
of ovulation and decreased FSH hormone levels.

12. ECOLOGICAL INFORMATION
ALL WORK PRACTICES MUST BE AIMED AT ELIMINATING ENVIRONMENTAL CONTAMINATION.
MOBILITY: This product has not been tested for mobility in soil.
PERSISTENCE AND BIODEGRADABILITY: This product has not been tested for persistence or biodegradability.
BIO-ACCUMULATION POTENTIAL: This product has not been tested for bio-accumulation potential.
ECOTOXICITY: This product has not been tested for aquatic or animal toxicity. Data are available for the trace
Octamethylcyclotetrasiloxane component. Although no data is available, under the Global Harmonization Standard, the Proprietary
Phenylated Ketoximo Silane component is classified as having chronic aquatic toxicity.
PROPRIETARY CYCLOSILOXANE:
LC50 (Oncorhynchus mykiss Rainbow trout) 14 days = 10 µg/L LC50 (Lepomis macrochirus Bluegill) 96 hours = > 1000 mg/L
LC50 (Brachydanio rerio Zebra danio) 96 hours = >500 mg/L OTHER ADVERSE EFFECTS: Components of this product are not reported to have any ozone depletion potential.
ENVIRONMENTAL EXPOSURE CONTROLS: Controls should be engineered to prevent release to the environment, including
procedures to prevent spills, atmospheric release and release to waterways.

13. DISPOSAL CONSIDERATIONS
PREPARING WASTES FOR DISPOSAL: As supplied, this product would not be a hazardous waste as defined by U.S. federal
regulation (40 CFR 261) if discarded or disposed. State and local regulations may differ from federal regulations. The generator of
the waste is responsible for proper waste determination and management.
U.S. EPA WASTE NUMBER: Not applicable.

14. TRANSPORTATION INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION: This product is NOT classified as Dangerous Goods, per U.S. DOT regulations, under
49 CFR 172.101.
TRANSPORT CANADA TRANSPORTATION OF DANGEROUS GOODS REGULATIONS: This product is NOT classified as
Dangerous Goods, per regulations of Transport Canada.
INTERNATIONAL AIR TRANSPORT ASSOCIATION SHIPPING INFORMATION (IATA): This product is NOT classified as
dangerous goods, per the International Air Transport Association.
INTERNATIONAL MARITIME ORGANIZATION SHIPPING INFORMATION (IMO): This product is not classified as dangerous
goods, per the International Maritime Organization.

Pecora 895 NST Page 7 of 9 November 9, 2017
15. REGULATORY INFORMATION
U.S. REGULATIONS:
U.S. SARA Reporting Requirements: No component of this product is subject to the reporting requirements of Sections 302, 304, and 313 of Title III of
the Superfund Amendments and Reauthorization Act.
U.S. SARA Hazard Categories (Section 311/312, 40 CFR 370-21): ACUTE: Yes; CHRONIC: Yes; FIRE: No; REACTIVE: No; SUDDEN
RELEASE: No
U.S. TSCA Inventory Status: All components of this product are in compliance with the inventory listing requirements of the U.S. Toxic Substances
Control Act (TSCA) Chemical Substance Inventory.
U.S. CERCLA Reportable Quantity (RQ): Not applicable.
U.S. Clean Air Act (CA 112r) Threshold Quantity (TQ): Not applicable.
California Safe Drinking Water and Toxic Enforcement Act (Proposition 65): The trace Quartz component (airborne, unbound particles of respirable
size) is found on the Proposition 65 List of chemicals known to the state to cause cancer. The Carbon Black component is also on the Proposition 65v
lists as compounds that may cause cancer by inhalation of unbound particles. Due to the form of the product, the Proposition 65 warning for these
compounds are not applicable to this product.
CANADIAN REGULATIONS:
Canadian DSL/NDSL Inventory Status: The components of this product listed by CAS# in Section 3 (MATERIAL IDENTIFICATION) are listed on the
DSL Inventory.
Canadian Environmental Protection Act (CEPA) Priorities Substances Lists: Not applicable.
Canadian WHMIS (HPR-GHS) 2015 Classification and Symbols: See Section 16 for in Classification and Symbols under HPR-GHS 2015.
MEXICAN REGULATIONS:
Mexican Workplace Regulations (NOM-018-STPS-2000): This product is not classified as hazardous.

16. OTHER INFORMATION
WARNINGS (per ANSI Z129.1): WARNING! CONTAINS TRACE COMPONENT THAT MAY CAUSE ADVERSE EFFECTS ON
FERTILITY, BASED ON ANIMAL DATA. MAY CAUSE EYE, SKIN, AND RESPIRATORY TRACT IRRITATION,
ESPECIALLY IF EXPOSURE IS PROLONGED. MAY BE HARMFUL IF ACCIDENTALLY INGESTED OR IN CONTACT WITH
THE SKIN. MAY CAUSE SKIN SENSITIZATION AND ALLERGIC REACTION IN SUSCEPTIBLE INDIVIDUALS. REPEATED
EXPOSURE MAY CAUSE ADVERSE SYSTEMIC EFFECTS. COMBUSTIBLE – CAN IGNITE IF EXPOSED TO DIRECT
FLAME. CONTAINS COMPOUNDS ACUTELY AND CHRONICALLY TOXIC TO AQUATIC ORGANISMS. Avoid contact with
eyes, skin, and clothing. Avoid breathing fumes, dusts, vapors or mist. Do not taste or swallow. Wash thoroughly after handling.
Keep container tightly closed. Use only with adequate ventilation. Keep away from heat and flame. Wear gloves, eye protection,
respiratory protection, and appropriate body protection. FIRST-AID: In case of contact, immediately flush skin and eyes with plenty of
water. Remove contaminated clothing and shoes. Get medical attention if irritation develops or persists. If inhaled, remove to fresh air.
If not breathing, give artificial respiration. If breathing is difficult, give oxygen. If swallowed, do not induce vomiting. Get medical
attention. IN CASE OF FIRE: Use water fog, foam, dry chemical, or CO2. IN CASE OF SPILL: Absorb spilled product with polypads
or other suitable absorbing material. Place all spill residue in an appropriate container and seal. Dispose of in accordance with U.S.
Federal, State, and local hazardous waste disposal regulations and those of Canada.
GLOBAL HARMONIZATION LABELING AND CLASSIFICATION: Classified in accordance with Global Harmonization Standard
under U.S. OSHA Hazard Communication Standard, Canadian WHMIS HPR-GHS 2015.
Classification: Reproductive Toxicity Category 2, Acute Oral Toxicity Category 5, Acute Dermal Toxicity Category 5, Eye Irritation Category 2A,
Skin Irritation Category 2, Skin Sensitization Category 1, Specific Organ Toxicity (Blood Effects) Repeated Exposure Category 3, Aquatic Chronic
Toxicity Category 4
Signal Word: Warning
Hazard Statements: H361f: Suspected of damaging fertility. H303 + H313: May be harmful if ingested or in contact with skin. H315: Causes skin
irritation. H319: Causes serious eye irritation. H317: May cause an allergic skin reaction. H373: May cause damage to blood through prolonged
or repeated exposure. H413: May be harmful to aquatic life with long-lasting effects.
Precautionary Statements:
Prevention: P201: Obtain special instructions before use. P202: Do not handle until all safety precautions have been read and understood. P260:
Do not breathe dust/gas/mist/vapours/spray. P264: Wash thoroughly after handling. P273: Avoid release to the environment. P280: Wear
protective gloves/protective clothing/eye protection/face protection.
Response: P308 + P313: IF exposed or concerned: Get medical advice/attention. P305 + P351 + P338: IF IN EYES: Rinse cautiously with water
for several minutes. Remove contact lenses, if present and easy to do. P337 + P313: If eye irritation persists: Get medical advice/attention.
P302 + P352: IF ON SKIN: Wash with plenty of soap and water. P333 + P313: If skin irritation or rash occurs: Get medical advice/attention.
P362 + P364: Take off contaminated clothing and wash it before reuse. P321: Specific treatment (remove from exposure and treat symptoms).
Storage: P405: Store locked up.
Disposal: P501: Dispose of contents/containers in accordance with all local, regional, national and international regulations.
Hazard Symbols/Pictogram: GHS07, GHS08
DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES
The information presented in this Safety Data Sheet is presented in good faith based on data believed to be accurate as of the date this Safety Data Sheet was prepared. HOWEVER, NO
WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY OTHER WARRANTY IS EXPRESSED OR IS TO BE IMPLIED REGARDING
THE ACCURACY OR COMPLETENESS OF THE INFORMATION PROVIDED ABOVE, THE RESULTS TO BE OBTAINED FROM THE USE OF THIS INFORMATION OR THE
PRODUCT, THE SAFETY OF THIS PRODUCT, OR THE HAZARDS RELATED TO ITS USE. In no case shall the descriptions, information, data or designs provided be considered a
part of our terms and conditions of sale.

Pecora 895 NST Page 8 of 9 November 9, 2017

16. OTHER INFORMATION (Continued)
DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES (continued)
All materials may present hazards and should be used with caution. Because many factors may affect processing or application/use, we recommend that you make tests to determine the suitability of a product for your particular purpose prior to use. No responsibility is assumed for any damage or injury resulting from abnormal use or from any failure to adhere to recommended practices or applicable federal, state, or local laws or regulations. The information provided above, and the product, are furnished on the condition that the person receiving them shall make their own determination as to the suitability of the product for their particular purpose and on the condition that they assume the risk of their use. In addition, no authorization
is given nor implied to practice any patented invention without a license.
REFERENCES AND DATA SOURCES: Contact the supplier for information.
METHODS OF EVALUATING INFORMATION FOR THE PURPOSE OF CLASSIFICATION: Bridging principles were used to classify this product.
REVISION DETAILS: July 2012: Up-date and revise entire SDS to include current GHS requirements. November 2017: Up-date of entire SDS for formulation change and
most current format and regulations.
DATE OF PRINTING January 5, 2018
DEFINITIONS OF TERMS
A large number of abbreviations and acronyms appear on a SDS. Some of these, which are commonly used, include the following:
KEY ACRONYMS:
CHEMTREC: Chemical Transportation Emergency Center, a 24-hour emergency information and/or emergency assistance to emergency responders.
CEILING LEVEL: The concentration that shall not be exceeded during any part of the working exposure.
DFG MAKs: Federal Republic of Germany Maximum Concentration Values in the workplace. Exposure limits are given as TWA (Time-Weighted Average) or PEAK (short-term exposure) values.
DFG MAK Germ Cell Mutagen Categories: 1: Germ cell mutagens that have been shown to increase the mutant frequency in the progeny of exposed humans. 2: Germ cell mutagens that have been shown
to increase the mutant frequency in the progeny of exposed mammals. 3A: Substances that have been
shown to induce genetic damage in germ cells of human of animals, or which produce mutagenic effects
in somatic cells of mammals in vivo and have been shown to reach the germ cells in an active form. 3B:
Substances that are suspected of being germ cell mutagens because of their genotoxic effects in
mammalian somatic cell in vivo; in exceptional cases, substances for which there are no in vivo data,
but that are clearly mutagenic in vitro and structurally related to known in vivo mutagens. 4: Not
applicable (Category 4 carcinogenic substances are those with non-genotoxic mechanisms of action.
By definition, germ cell mutagens are genotoxic. Therefore, a Category 4 for germ cell mutagens cannot
apply. At some time in the future, it is conceivable that a Category 4 could be established for genotoxic
substances with primary targets other than DNA [e.g. purely aneugenic substances] if research results make this seem sensible.) 5: Germ cell mutagens, the potency of which is considered to be so low that,
provided the MAK value is observed, their contribution to genetic risk for humans is expected not to be significant.
DFG MAK Pregnancy Risk Group Classification: Group A: A risk of damage to the developing embryo or fetus has been unequivocally demonstrated. Exposure of pregnant women can lead to damage
of the developing organism, even when MAK and BAT (Biological Tolerance Value for Working Materials) values are observed. Group B: Currently available information indicates a risk of damage
to the developing embryo or fetus must be considered to be probable. Damage to the developing organism cannot be excluded when pregnant women are exposed, even when MAK and BAT values
are observed. Group C: There is no reason to fear a risk of damage to the developing embryo or fetus when MAK and BAT values are observed. Group D: Classification in one of the groups A–C is not
yet possible because, although the data available may indicate a trend, they are not sufficient for final
evaluation.
IDLH: Immediately Dangerous to Life and Health. This level represents a concentration from which
one can escape within 30-minutes without suffering escape-preventing or permanent injury.
LOQ: Limit of Quantitation.
NE: Not Established. When no exposure guidelines are established, an entry of NE is made for
reference.
NIC: Notice of Intended Change.
NIOSH CEILING: The exposure that shall not be exceeded during any part of the workday. If
instantaneous monitoring is not feasible, the ceiling shall be assumed as a 15-minute TWA exposure (unless otherwise specified) that shall not be exceeded at any time during a workday.
NIOSH RELs: NIOSH’s Recommended Exposure Limits. PEL: OSHA's Permissible Exposure Limits. This exposure value means exactly the same as a TLV,
except that it is enforceable by OSHA. The OSHA Permissible Exposure Limits are based in the 1989 PELs and the June, 1993 Air Contaminants Rule (Federal Register: 58: 35338-35351 and 58: 40191).
Both the current PELs and the vacated PELs are indicated. The phrase, “Vacated 1989 PEL” is placed next to the PEL that was vacated by Court Order.
SKIN: Used when a there is a danger of cutaneous absorption.
STEL: Short Term Exposure Limit, usually a 15-minute time-weighted average (TWA) exposure that
should not be exceeded at any time during a workday, even if the 8-hr TWA is within the TLV-TWA,
PEL-TWA or REL-TWA.
TLV: Threshold Limit Value. An airborne concentration of a substance that represents conditions under
which it is generally believed that nearly all workers may be repeatedly exposed without adverse effect.
The duration must be considered, including the 8-hour.
TWA: Time Weighted Average exposure concentration for a conventional 8-hr (TLV, PEL) or up to a
10-hr (REL) workday and a 40-hr workweek.
WEEL: Workplace Environmental Exposure Limits from the AIHA.
HAZARD RATINGS:
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HAZARD
RATINGS: This rating system was developed by the National Paint and Coating Association and
has been adopted by industry to identify the degree of chemical hazards.
HEALTH HAZARD: 0 Minimal Hazard: No significant health risk, irritation of skin or eyes not
anticipated. Skin Irritation: Essentially non-irritating. Mechanical irritation may occur. PII or Draize =
0. Eye Irritation: Essentially non-irritating, minimal effects clearing in < 24 hours. Mechanical irritation
may occur. Draize = 0. Oral Toxicity LD50 Rat: > 5000 mg/kg. Dermal Toxicity LD50 Rat or Rabbit: >
2000 mg/kg. Inhalation Toxicity 4-hrs LC50 Rat: > 20 mg/L. 1 Slight Hazard: Minor reversible injury
may occur; may irritate the stomach if swallowed; may defat the skin and exacerbate existing dermatitis. Skin Irritation: Slightly or mildly irritating. PII or Draize > 0 < 5. Eye Irritation: Slightly to mildly
irritating, but reversible within 7 days. Draize > 0 ≤ 25. Oral Toxicity LD50 Rat: > 500–5000 mg/kg. Dermal Toxicity LD50 Rat or Rabbit: > 1000–2000 mg/kg. Inhalation Toxicity LC50 4-hrs Rat: > 2–20
mg/L. 2 Moderate Hazard: Temporary or transitory injury may occur; prolonged exposure may affect the CNS. Skin Irritation: Moderately irritating; primary irritant; sensitizer. PII or Draize ≥ 5, with no
destruction of dermal tissue. Eye Irritation: Moderately to severely irritating; reversible corneal opacity; corneal involvement or irritation clearing in 8–21 days. Draize = 26–100, with reversible effects. Oral
Toxicity LD50 Rat: > 50–500 mg/kg. Dermal Toxicity LD50 Rat or Rabbit: > 200–1000 mg/kg. Inhalation Toxicity LC50 4-hrs Rat: > 0.5–2 mg/L.
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HAZARD
RATINGS (continued):
HEALTH HAZARD (continued): 3 Serious Hazard: Major injury likely unless prompt action is taken
and medical treatment is given; high level of toxicity; corrosive. Skin Irritation: Severely irritating
and/or corrosive; may cause destruction of dermal tissue, skin burns, and dermal necrosis. PII or Draize
> 5–8, with destruction of tissue. Eye Irritation: Corrosive, irreversible destruction of ocular tissue;
corneal involvement or irritation persisting for more than 21 days. Draize > 80 with effects irreversible in 21 days. Oral Toxicity LD50 Rat: > 1–50 mg/kg. Dermal Toxicity LD50 Rat or Rabbit: > 20–200
mg/kg. Inhalation Toxicity LC50 4-hrs Rat: > 0.05–0.5 mg/L.4 Severe Hazard: Life-threatening; major or permanent damage may result from single or repeated exposure; extremely toxic; irreversible injury
may result from brief contact. Skin Irritation: Not appropriate. Do not rate as a 4, based on skin irritation alone. Eye Irritation: Not appropriate. Do not rate as a 4, based on eye irritation alone. Oral Toxicity
LD50 Rat: ≤ 1 mg/kg. Dermal Toxicity LD50 Rat or Rabbit: ≤ 20 mg/kg. Inhalation Toxicity LC50 4-hrs Rat: ≤ 0.05 mg/L.
FLAMMABILITY HAZARD: 0 Minimal Hazard: Materials that will not burn in air when exposure to a temperature of 815.5°C (1500°F) for a period of 5 minutes. 1 Slight Hazard: Materials that must be
pre-heated before ignition can occur. Material requires considerable pre-heating, under all ambient temperature conditions before ignition and combustion can occur. This usually includes the following:
Materials that will burn in air when exposed to a temperature of 815.5°C (1500°F) for a period of 5
minutes or less; Liquids, solids and semisolids having a flash point at or above 93.3°C (200°F) (i.e.
OSHA Class IIIB); and Most ordinary combustible materials (e.g. wood, paper, etc.). 2 Moderate
Hazard: Materials that must be moderately heated or exposed to relatively high ambient temperatures
before ignition can occur. Materials in this degree would not, under normal conditions, form hazardous
atmospheres in air, but under high ambient temperatures or moderate heating may release vapor in
sufficient quantities to produce hazardous atmospheres with air. This usually includes the following:
Liquids having a flash-point at or above 37.8°C (100°F); Solid materials in the form of course dusts
that may burn rapidly but that generally do not form explosive atmospheres; Solid materials in a fibrous
or shredded form that may burn rapidly and create flash fire hazards (e.g. cotton, sisal, hemp); and Solids and semisolids (e.g. viscous and slow flowing as asphalt) that readily give off flammable vapors.
3 Serious Hazard: Liquids and solids that can be ignited under almost all ambient temperature conditions. Materials in this degree produce hazardous atmospheres with air under almost all ambient
temperatures, or, unaffected by ambient temperature, are readily ignited under almost all conditions. This usually includes the following: Liquids having a flash point below 22.8°C (73°F) and having a
boiling point at or above 38°C (100°F) and those liquids having a flash point at or above 22.8°C (73°F) and below 37.8°C (100°F) (i.e. OSHA Class IB and IC); Materials that on account of their
physical form or environmental conditions can form explosive mixtures with air and are readily dispersed in air (e.g., dusts of combustible solids, mists or droplets of flammable liquids); and Materials
that burn extremely rapidly, usually by reason of self-contained oxygen (e.g. dry nitrocellulose and many organic peroxides). 4 Severe Hazard: Materials that will rapidly or completely vaporize at
atmospheric pressure and normal ambient temperature or that are readily dispersed in air, and that will
burn readily. This usually includes the following: Flammable gases; Flammable cryogenic materials;
Any liquid or gaseous material that is liquid while under pressure and has a flash point below 22.8°C
(73°F) and a boiling point below 37.8°C (100°F) (i.e. OSHA Class IA); and Materials that ignite
spontaneously when exposed to air at a temperature of 54.4°C (130°F) or below (pyrophoric).
PHYSICAL HAZARD: 0 Water Reactivity: Materials that do not react with water. Organic Peroxides:
Materials that are normally stable, even under fire conditions and will not react with water. Explosives:
Substances that are Non-Explosive. Compressed Gases: No Rating. Pyrophorics: No Rating. Oxidizers:
No 0 rating. Unstable Reactives: Substances that will not polymerize, decompose, condense, or self-
react.). 1 Water Reactivity: Materials that change or decompose upon exposure to moisture. Organic Peroxides: Materials that are normally stable, but can become unstable at high temperatures and
pressures. These materials may react with water, but will not release energy violently. Explosives: Division 1.5 & 1.6 explosives. Substances that are very insensitive explosives or that do not have a
mass explosion hazard. Compressed Gases: Pressure below OSHA definition. Pyrophorics: No Rating. Oxidizers: Packaging Group III oxidizers; Solids: any material that in either concentration tested,
exhibits a mean burning time less than or equal to the mean burning time of a 3:7 potassium bromate/cellulose mixture and the criteria for Packing Group I and II are not met. Liquids: any material
that exhibits a mean pressure rise time less than or equal to the pressure rise time of a 1:1 nitric acid (65%)/cellulose mixture and the criteria for Packing Group I and II are not met. Unstable Reactives:
Substances that may decompose condense, or self-react, but only under conditions of high temperature and/or pressure and have little or no potential to cause significant heat generation or explosion hazard.
Substances that readily undergo hazardous polymerization in the absence of inhibitors. 2 Water
Reactivity: Materials that may react violently with water. Organic Peroxides: Materials that, in
themselves, are normally unstable and will readily undergo violent chemical change, but will not
detonate. These materials may also react violently with water. Explosives: Division 1.4 explosives.
Explosive substances where the explosive effects are largely confined to the package and no projection
of fragments of appreciable size or range are expected. An external fire must not cause virtually
instantaneous explosion of almost the entire contents of the package. Compressed Gases: Pressurized
and meet OSHA definition but < 514.7 psi absolute at 21.1°C (70°F) [500 psig]. Pyrophorics: No
Rating. Oxidizers: Packing Group II oxidizers. Solids: any material that, either in concentration tested,
exhibits a mean burning time of less than or equal to the mean burning time of a 2:3 potassium bromate/cellulose mixture and the criteria for Packing Group I are not met. Liquids: any material that
exhibits a mean pressure rise time less than or equal to the pressure rise of a 1:1 aqueous sodium chlorate solution (40%)/cellulose mixture and the criteria for Packing Group I are not met. Reactives: Substances
that may polymerize, decompose, condense, or self-react at ambient temperature and/or pressure, but have a low potential (or low risk) for significant heat generation or explosion. Substances that readily
form peroxides upon exposure to air or oxygen at room temperature.
Pecora 895 NST Page 9 of 9 November 9, 2017
DEFINITIONS OF TERMS (Continued)
HAZARDOUS MATERIALS IDENTIFICATION SYSTEM HAZARD
RATINGS (continued):
PHYSICAL HAZARD (continued): 3 Water Reactivity: Materials that may form explosive reactions
with water. Organic Peroxides: Materials that are capable of detonation or explosive reaction, but require a strong initiating source or must be heated under confinement before initiation; or materials
that react explosively with water. Explosives: Division 1.3 explosives. Explosive substances that have a fire hazard and either a minor blast hazard or a minor projection hazard or both, but do not have a
mass explosion hazard. Compressed Gases: Pressure ≥ 514.7 psi absolute at 21.1°C (70°F) [500 psig]. Pyrophorics: No Rating. Oxidizers: Packing Group I oxidizers. Solids: any material that, in either
concentration tested, exhibits a mean burning time less than the mean burning time of a 3:2 potassium
bromate/cellulose mixture. Liquids: any material that spontaneously ignites when mixed with cellulose
in a 1:1 ratio, or which exhibits a mean pressure rise time less than the pressure rise time of a 1:1
perchloric acid (50%)/cellulose mixture. Unstable Reactives: Substances that may polymerize,
decompose, condense, or self-react at ambient temperature and/or pressure and have a moderate
potential (or moderate risk) to cause significant heat generation or explosion. 4 Water Reactivity:
Materials that react explosively with water without requiring heat or confinement. Organic Peroxides:
Materials that are readily capable of detonation or explosive decomposition at normal temperature and
pressures. Explosives: Division 1.1 & 1.2 explosives. Explosive substances that have a mass explosion
hazard or have a projection hazard. A mass explosion is one that affects almost the entire load instantaneously. Compressed Gases: No Rating. Pyrophorics: Add to the definition of Flammability 4.
Oxidizers: No 4 rating. Unstable Reactives: Substances that may polymerize, decompose, condense, or self-react at ambient temperature and/or pressure and have a high potential (or high risk) to cause
significant heat generation or explosion. Pyrophorics: Add to the definition of Flammability 4. Oxidizers: No 4 rating. Unstable Reactives: Substances that may polymerize, decompose, condense, or
self-react at ambient temperature and/or pressure and have a high potential (or high risk) to cause significant heat generation or explosion.
NATIONAL FIRE PROTECTION ASSOCIATION HAZARD RATINGS
HEALTH HAZARD: 0 Materials that, under emergency conditions, would offer no hazard beyond that of ordinary combustible materials. Gases and vapors with an LC50 for acute inhalation toxicity greater
than 10,000 ppm. Dusts and mists with an LC50 for acute inhalation toxicity greater than 200 mg/L. Materials with an LD50 for acute dermal toxicity greater than 2000 mg/kg. Materials with an LD50 for
acute oral toxicity greater than 2000 mg/kg. Materials essentially non-irritating to the respiratory tract, eyes, and skin. 1 Materials that, under emergency conditions, can cause significant irritation. Gases and
vapors with an LC50 for acute inhalation toxicity greater than 5,000 ppm but less than or equal to 10,000 ppm. Dusts and mists with an LC50 for acute inhalation toxicity greater than 10 mg/L but less than or
equal to 200 mg/L. Materials with an LD50 for acute dermal toxicity greater than 1000 mg/kg but less than or equal to 2000 mg/kg. Materials that slightly to moderately irritate the respiratory tract, eyes and
skin. Materials with an LD50 for acute oral toxicity greater than 500 mg/kg but less than or equal to 2000 mg/kg. 2 Materials that, under emergency conditions, can cause temporary incapacitation or
residual injury. Gases with an LC50 for acute inhalation toxicity greater than 3,000 ppm but less than or
equal to 5,000 ppm. Any liquid whose saturated vapor concentration at 20°C (68°F) is equal to or
greater than one-fifth its LC50 for acute inhalation toxicity, if its LC50 is less than or equal to 5000 ppm
and that does not meet the criteria for either degree of hazard 3 or degree of hazard 4. Dusts and mists
with an LC50 for acute inhalation toxicity greater than 2 mg/L but less than or equal to 10 mg/L.
Materials with an LD50 for acute dermal toxicity greater than 200 mg/kg but less than or equal to 1000
mg/kg. Compressed liquefied gases with boiling points between -30°C (-22°F) and -55°C (-66.5°F) that
cause severe tissue damage, depending on duration of exposure. Materials that are respiratory irritants.
Materials that cause severe, but reversible irritation to the eyes or are lachrymators. Materials that are
primary skin irritants or sensitizers. Materials whose LD50 for acute oral toxicity is greater than 50 mg/kg but less than or equal to 500 mg/kg. 3 Materials that, under emergency conditions, can cause
serious or permanent injury. Gases with an LC50 for acute inhalation toxicity greater than 1,000 ppm but less than or equal to 3,000 ppm. Any liquid whose saturated vapor concentration at 20°C (68°F) is
equal to or greater its LC50 for acute inhalation toxicity, if its LC50 is less than or equal to 3000 ppm and that does not meet the criteria for degree of hazard 4. Dusts and mists with an LC50 for acute inhalation
toxicity greater than 0.5 mg/L but less than or equal to 2 mg/L. Materials with an LD50 for acute dermal toxicity greater than 40 mg/kg but less than or equal to 200 mg/kg. Materials that are corrosive to the
respiratory tract. Materials that are corrosive to the eyes or cause irreversible corneal opacity. Materials corrosive to the skin. Cryogenic gases that cause frostbite and irreversible tissue damage. Compressed
liquefied gases with boiling points below -55°C (-66.5°F) that cause frostbite and irreversible tissue damage. Materials with an LD50 for acute oral toxicity greater than 5 mg/kg but less than or equal to 50
mg/kg. 4 Materials that, under emergency conditions, can be lethal. Gases with an LC50 for acute
inhalation toxicity less than or equal to 1,000 ppm. Any liquid whose saturated vapor concentration at
20°C (68°F) is equal to or greater than ten times its LC50 for acute inhalation toxicity, if its LC50 is less
than or equal to 1000 ppm. Dusts and mists whose LC50 for acute inhalation toxicity is less than or equal
to 0.5 mg/L. Materials whose LD50 for acute dermal toxicity is less than or equal to 40 mg/kg. Materials
whose LD50 for acute oral toxicity is less than or equal to 5 mg/kg.
FLAMMABILITY HAZARD: 0 Materials that will not burn under typical fire conditions, including
intrinsically noncombustible materials such as concrete, stone, and sand. Materials that will not burn in
air when exposed to a temperature of 816°C (1500°F) for a period of 5 minutes in according with Annex
D of NFPA 704. 1 Materials that must be preheated before ignition can occur. Materials in this degree require considerable preheating, under all ambient temperature conditions, before ignition and
combustion can occur: Materials that will burn in air when exposed to a temperature of 816°C (1500°F) for a period of 5 minutes in according with Annex D of NFPA 704. Liquids, solids, and semisolids
having a flash point at or above 93.4°C (200°F) (i.e. Class IIIB liquids). Liquids with a flash point greater than 35°C (95°F) that do not sustain combustion when tested using the Method of Testing for
Sustained Combustibility, per 49 CFR 173, Appendix H or the UN Recommendations on the Transport of Dangerous Goods, Model Regulations (current edition) and the related Manual of Tests and Criteria
(current edition). Liquids with a flash point greater than 35°C (95°F) in a water-miscible solution or dispersion with a water non-combustible liquid/solid content of more than 85% by weight. Liquids that
have no fire point when tested by ASTM D 92, Standard Test Method for Flash and Fire Points by Cleveland Open Cup, up to the boiling point of the liquid or up to a temperature at which the sample
being tested shows an obvious physical change. Combustible pellets with a representative diameter of
greater than 2 mm (10 mesh). Most ordinary combustible materials. Solids containing greater than 0.5%
by weight of a flammable or combustible solvent are rated by the closed cup flash point of the solvent.
2 Materials that must be moderately heated or exposed to relatively high ambient temperatures before
ignition can occur. Materials in this degree would not under normal conditions form hazardous
atmospheres with air, but under high ambient temperatures or under moderate heating could release
vapor in sufficient quantities to produce hazardous atmospheres with air. Liquids having a flash point
at or above 37.8°C (100°F) and below 93.4°C (200°F) (i.e. Class II and Class IIIA liquids.) Solid
materials in the form of powders or coarse dusts of representative diameter between 420 microns (40
mesh) and 2 mm (10 mesh) that burn rapidly but that generally do not form explosive mixtures with air.
NATIONAL FIRE PROTECTION ASSOCIATION HAZARD RATINGS
(continued):
FLAMMABILITY HAZARD (continued): 2 (continued): Solid materials in fibrous or shredded form
that burn rapidly and create flash fire hazards, such as cotton, sisal, and hemp. Solids and semisolids that readily give off flammable vapors. Solids containing greater than 0.5% by weight of a flammable
or combustible solvent are rated by the closed cup flash point of the solvent. 3 Liquids and solids that can be ignited under almost all ambient temperature conditions. Materials in this degree produce
hazardous atmospheres with air under almost all ambient temperatures or, though unaffected by ambient temperatures, are readily ignited under almost all conditions. Liquids having a flash point below 22.8°C
(73°F) and having a boiling point at or above 37.8°C (100°F) and those liquids having a flash point at
or above 22.8°C (73°F) and below 37.8°C (100°F) (i.e. Class IB and IC liquids). Materials that on
account of their physical form or environmental conditions can form explosive mixtures with air and
are readily dispersed in air. Flammable or combustible dusts with representative diameter less than 420
microns (40 mesh). Materials that burn with extreme rapidity, usually by reason of self-contained
oxygen (e.g. dry nitrocellulose and many organic peroxides). Solids containing greater than 0.5% by
weight of a flammable or combustible solvent are rated by the closed cup flash point of the solvent. 4
Materials that will rapidly or completely vaporize at atmospheric pressure and normal ambient
temperature or that are readily dispersed in air and will burn readily. Flammable gases. Flammable
cryogenic materials. Any liquid or gaseous materials that is liquid while under pressure and has a flash point below 22.8°C (73°F) and a boiling point below 37.8°C (100°F) (i.e. Class IA liquids). Materials
that ignite when exposed to air, Solids containing greater than 0.5% by weight of a flammable or combustible solvent are rated by the closed cup flash point of the solvent.
INSTABILITY HAZARD: 0 Materials that in themselves are normally stable, even under fire conditions. Materials that have an instantaneous power density (product of heat of reaction and reaction
rate) at 250°C (482°F) below 0.01 W/mL. Materials that do not exhibit an exotherm at temperatures less than or equal to 500°C (932°F) when tested by differential scanning calorimetry.1 Materials that
in themselves are normally stable, but that can become unstable at elevated temperatures and pressures. Materials that have an instantaneous power density (product of heat of reaction and reaction rate) at
250°C (482°F) at or above 0.01 W/mL and below 10 W/mL. 2 Materials that readily undergo violent chemical change at elevated temperatures and pressures. Materials that have an instantaneous power
density (product of heat of reaction and reaction rate) at 250°C (482°F) at or above 10 W/mL and below
100W/mL. 3 Materials that in themselves are capable of detonation or explosive decomposition or
explosive reaction, but that require a strong initiating source or that must be heated under confinement
before initiation. Materials that have an estimated instantaneous power density (product of heat of
reaction and reaction rate) at 250°C (482°F) at or above 100 W/mL and below 1000 W/mL. Materials
that are sensitive to thermal or mechanical shock at elevated temperatures and pressures. 4 Materials
that in themselves are readily capable of detonation or explosive decomposition or explosive reaction
at normal temperatures and pressures. Materials that are sensitive to localized thermal or mechanical
shock at normal temperatures and pressures. Materials that have an estimated instantaneous power
density (product of heat of reaction and reaction rate) at 250°C (482°F) of 1000 W/mL or greater.
FLAMMABILITY LIMITS IN AIR:
Much of the information related to fire and explosion is derived from the National Fire Protection
Association (NFPA). Flash Point: Minimum temperature at which a liquid gives off sufficient vapor to
form an ignitable mixture with air near the surface of the liquid or within the test vessel used.
Autoignition Temperature: Minimum temperature of a solid, liquid, or gas required to initiate or cause
self-sustained combustion in air with no other source of ignition. LEL: Lowest concentration of a
flammable vapor or gas/air mixture that will ignite and burn with a flame. UEL: Highest concentration
of a flammable vapor or gas/air mixture that will ignite and burn with a flame.
TOXICOLOGICAL INFORMATION:
Human and Animal Toxicology: Possible health hazards as derived from human data, animal studies,
or from the results of studies with similar compounds are presented. LD50: Lethal Dose (solids &
liquids) that kills 50% of the exposed animals. LC50: Lethal Concentration (gases) that kills 50% of the
exposed animals. ppm: Concentration expressed in parts of material per million parts of air or water.
mg/m3: Concentration expressed in weight of substance per volume of air. mg/kg: Quantity of material,
by weight, administered to a test subject, based on their body weight in kg. TDLo: Lowest dose to cause
a symptom. TCLo: Lowest concentration to cause a symptom. TDo, LDLo, and LDo, or TC, TCo,
LCLo, and LCo: Lowest dose (or concentration) to cause lethal or toxic effects. Cancer Information:
IARC: International Agency for Research on Cancer. NTP: National Toxicology Program. RTECS: Registry of Toxic Effects of Chemical Substances. IARC and NTP rate chemicals on a scale of
decreasing potential to cause human cancer with rankings from 1 to 4. Subrankings (2A, 2B, etc.) are also used. Other Information: BEI: ACGIH Biological Exposure Indices, represent the levels of
determinants which are most likely to be observed in specimens collected from a healthy worker who has been exposed to chemicals to the same extent as a worker with inhalation exposure to the TLV.
REPRODUCTIVE INFORMATION: A mutagen is a chemical that causes permanent
changes to genetic material (DNA) such that the changes will propagate through generational lines.
An embryotoxin is a chemical that causes damage to a developing embryo (i.e. within the first eight
weeks of pregnancy in humans), but the damage does not propagate across generational lines. A
teratogen is a chemical that causes damage to a developing fetus, but the damage does not propagate
across generational lines. A reproductive toxin is any substance that interferes in any way with the
reproductive process. ECOLOGICAL INFORMATION:
EC: Effect concentration in water. BCF: Bioconcentration Factor, which is used to determine if a
substance will concentrate in life forms that consume contaminated plant or animal matter. TLm:
Median threshold limit. log KOW or log KOC: Coefficient of Oil/Water Distribution is used to assess a
substance’s behavior in the environment. REGULATORY INFORMATION: This section explains the impact of various laws and
regulations on the material.
U.S.:
EPA: U.S. Environmental Protection Agency. ACGIH: American Conference of Governmental
Industrial Hygienists, a professional association that establishes exposure limits. OSHA: U.S.
Occupational Safety and Health Administration. NIOSH: National Institute of Occupational Safety and
Health, which is the research arm of OSHA. DOT: U.S. Department of Transportation. TC: Transport
Canada. SARA: Superfund Amendments and Reauthorization Act. TSCA: U.S. Toxic Substance
Control Act. CERCLA: Comprehensive Environmental Response, Compensation, and Liability Act. Marine Pollutant status according to the DOT; CERCLA or Superfund; and various state regulations.
This section also includes information on the precautionary warnings that appear on the material’s package label.
CANADA: WHMIS: Canadian Workplace Hazardous Materials Information System. TC: Transport Canada.
DSL/NDSL: Canadian Domestic/Non-Domestic Substances List.

GAF
Safety Data Sheet
SDS #2029
SDS Date: December 2014
_________________________________________________________________________
Page 1 of 8

SECTION 1: PRODUCT AND COMPANY INFORMATION

Everguard® TPO Seam Cleaner
N/A
N/A
N/A
GAF
1 Campus Drive, Parsippany, NJ 07054
800–424–9300
800–766–3411
Corporate EHS
Corporate EHS

SECTION 2: HAZARD IDENTIFICATION

NFPA and HMIS RATINGS:

NFPA Hazard
Rating

HMIS Hazard
Rating

Health 2 Health 2
Flammable 3 Flammable 3
Reactive 0 Reactive 0
Special Hazards - Personal Protection X

GHS LABEL ELEMENTS:

GHS CLASSIFICATION: Flammable Liquid - Category 2
Eye Irritant - Category 2A
Skin Irritant - Category 2
Acute Toxicity - Category 4
Target Organ (SE) - Category 3
Target Organ (RE) - Category 2
Aspiration Toxicity - Category 1
Hazardous to the Aquatic Environment - Category 2

GAF SDS # 2029

Page 2 of 8

Inhalation, Skin Absorption, Skin Contact, Eye Contact, Ingestion

Can cause eye irritation. Symptoms include stinging, tearing,
redness, swelling of the eyes and/or blurred vision.

Can cause skin irritation. Prolonged or repeated contact may dry
the skin. Symptoms may include redness, burning, and drying and
cracking of skin, burns and other skin damage such as blistering.
Passage of this material into the body through the skin is possible,
but it is unlikely that this would result in harmful effects during safe
handling and use.

Swallowing small amounts of this material during normal handling is
not likely to cause harmful effects. Swallowing large amounts may
be harmful. This material can get into the lungs during swallowing or
while vomiting. This results in lung inflammation and other lung
injury.

Breathing of vapor or mist is possible. Breathing small amounts of
this material during normal handling is not likely to cause harmful
effects. Breathing large amounts may be harmful. Symptoms are
not expected at air concentrations below the recommended
exposure limits.

Signs and symptoms of exposure to this material through breathing,
swallowing, and/or passage of the material through the skin may
include; metallic taste, redness of the skin, stomach or intestinal
upset (nausea, vomiting, diarrhea, irritation (nose, throat, airways),
discomfort in the chest, central nervous system excitation
(giddiness, liveliness, light-headed feeling), followed by central
nervous system depression (dizziness, drowsiness, weakness,
fatigue, nausea, headache, unconsciousness), and other central
nervous system effects, temporary changes in mood and behavior,
effects on memory, weakness, respiratory depression (slowing of

GHS PICTOGRAMS:

SIGNAL WORD:

Danger

HAZARD
STATEMENTS:

Highly flammable liquid and vapor
May cause damage to organs through prolonged or repeated exposure
Causes skin irritation
Causes serious eye irritation
May cause respiratory irritation
Harmful if inhaled
May be fatal if swallowed and enters airways Toxic to aquatic life with long lasting effects

GAF SDS # 2029

Page 3 of 8
the breathing rate), shortness of breath, lack of coordination,
confusion, irregular heartbeat, narcosis (dazed or sluggish feeling),
coma, and death.

CHRONIC HEALTH HAZARDS:

Overexposure to this material, (or its components), has been
suggested as a cause of the following effects in laboratory animals:
mild, reversible liver effects, mild, reversible kidney effects, cardiac
sensitization, and kidney damage. This material, (or a component),
has been shown to cause birth defects in laboratory animal studies.
The relevance of these findings to humans is uncertain. This
material is not expected to cause cancer in humans since it did not
cause cancer in laboratory animals.

CARCINOGENICITY:

Ethyl Benzene has been shown to cause cancer in laboratory
animals. The relevance of this finding in humans is uncertain. The
International Agency for Research on Cancer (IARC) has classified
ethyl benzene as a possible human carcinogen. Toluene may be
harmful to the human fetus based on positive test results with
laboratory animals. Case studies show that prolonged
intentional abuse of toluene during pregnancy can cause birth
defects in humans.

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Xylene 1330-20-7 >=77% 100 ppm 100 ppm REL 100 ppm
Ethyl Benzene 100-41-4 >=22% 100 ppm 100 ppm REL 100 ppm

SECTION 4: FIRST AID MEASRURES

If symptoms develop, immediately move individual away from exposure
and into fresh air. Flush eyes gently with water for at least 15 minutes
while holding eyelids apart; seek immediate medical attention.

Remove contaminated clothing. Flush exposed areas with large amounts
of water. If skin is damaged, seek immediate medical attention. If skin is
not damaged and symptoms persist, seek medical attention. Launder
clothing before reuse.

If symptoms develop, move individual away form exposure and into fresh
air. If symptoms persist, seek medical attention. If breathing is difficult,
administer oxygen. Keep person warn and quiet; seek immediate
medical attention.

GAF SDS # 2029

Page 4 of 8
INGESTION:

Seek medical attention immediately. If individual is drowsy or
unconscious, do not give anything by mouth; place individual on the left
side with head down. Contact a physician, medical facility, or poison
control center for advice about whether to induce vomiting. If possible, do
not leave individual unattended.

NOTES TO PHYSICIANS OR
FIRST AID PROVIDERS:

Inhalation of high concentrations of this material, as could occur in
enclosed spaces or during deliberate abuse, may be associated with
cardiac arrhythmias. Sympathomimetic drugs may initiate cardiac
arrhythmias in persons exposed to this material. This material is an
aspiration hazard. Potential danger form aspiration must be weighed
against possible oral toxicity when deciding whether to induce vomiting.

SECTION 5: FIRE FIGHTING PROCEDURES

Dry chemical, Foam, Carbon Dioxide (CO2)
Carbon dioxide and carbon monoxide, hydrocarbons
Wear full fire fighting turn-out gear, (full bunker gear), and
respiratory protection, (SCBA).
Material is volatile and readily gives off vapors which may
travel along the ground or be moved by ventilation and ignited
by pilot lights, flames, sparks, heaters, smoking, electric
motors, static discharge or other ignition sources at locations
near the material handling pint. Never use welding or cutting
torch on or near drum, (even empty), because product, (even
just residue), can ignite explosively.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Wear appropriate protective equipment as described in section 8.
Eliminate all sources of ignition. Persons not wearing protective
equipment should be excluded from area of spill until clean-up has
been completed. Stop spill at the source. Prevent spill from
spreading and entering drains, sewers, streams, or other bodies of
water. If runoff occurs, notify authorities as required. Pump or
vacuum transfer spilled product to clean containers for recovery.
Absorb unrecoverable product. Transfer contaminated absorbent,
soil and other materials to containers for disposal.

SECTION 7: HANDLING AND STORAGE

Containers of this material may be hazardous when emptied.
Since emptied containers retain product residues, (vapors, liquid,
GAF SDS # 2029

Page 5 of 8

and/or solid), all hard precautions given in the data sheet must
be observed. Static ignition hazard can result from handling and
use. Electrically bond and ground all containers, personnel and
equipment before transfer or use of material. Special precautions
may be necessary to dissipate static electricity for non-
conductive containers. Use proper bonding and grounding during
product transfer as described in National Fire Protection
Association document NFPA 77.

OTHER PRECAUTIONS:

Absorb liquid of vermiculite, floor absorbent or other absorbent
material.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

Provide sufficient mechanical ventilation to maintain exposure
below exposure limits.

If workplace exposure limit(s) of product or any component is
exceeded, a NIOSH-approved air supplied respirator is advised in
absence of proper environmental control. OSHA regulations also
permit other NIOSH respirators, (negative pressure type), under
specified conditions. Engineering or administrative controls should
be implemented to reduce exposure.

Chemical splash goggles.

Wear resistant gloves.

To prevent repeated or prolonged skin contact, wear impervious
clothing and boots.

N/A

N/A

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Colorless liquid. Mild Aromatic odor.
79.90F / 26.660C 1.0%
N/A 6.6%
.86 (N-Butyl
Acetate)
137.000F /
278.600C
7 -52.600F /
-47.000C
Negligible in water N/A
GAF SDS # 2029

Page 6 of 8

VAPOR DENSITY:

3.66 (AIR=1) PERCENT VOLATILE: N/A
VAPOR PRESSURE:

1.06 kPa @ 77oF /
25oC
MOLECULAR WEIGHT:

N/A
VOC WITH WATER (LBS/GAL):

7.25 lb/gal @ 77oF
/ 25oC
WITHOUT WATER (LBS/GAL): N/A

SECTION 10: STABILITY AND REACTIVITY

N/A
Strong oxidizing agents.
Carbon Dioxide and carbon monoxide, hydrocarbons
None

__________________________________________________________________________________________
SECTION 11: TOXICOLOGICAL INFORMATION

Xylene LD 50 Rat: 4,300 mg/kg

Ethyl Benzene LD 50 Rat: 3,500 mg/kg

Ethyl Benzene LC Lo Rat: 4000 ppm, 4 h

Xylene LD 50 Rabbit: > 2,000 mg/kg

Ethyl Benzene LD 50 Rabbit: 15,433 mg/kg

SECTION 12: ECOLOGICAL INFORMATION

GAF SDS # 2029

Page 7 of 8
ECOLOGICAL INFORMATION:

Aquatic toxicity

Acute and Prolonged Toxicity to Fish

96 h LC 50 Rainbow trout, Donaldson trout (Oncorhynchus mykiss): 6.7
– 10 mg/1 Mortality

96 h LC 50 Fathead minnow (Pimephales promelas): 23.53 – 29.97
mg/1 Mortality

Acute Toxicity to Aquatic Invertebrates

24 h LC 50 Water flea (Daphnia magna),: > 100-<1,000 mg/l Mortality

__________________________________________________________________________________________
SECTION 13: DISPOSAL CONSIDERATIONS

This product, as supplied, is regulated as a hazardous waste by the U.S.
Environmental Protection Agency (EPA) under Resource Conservation
and Recovery Act (RCRA) regulations. If discarded in its purchased form,
this product is a RCRA hazardous waste. It is the responsibility of the
product user to determine at the time of disposal, whether a material
containing the product or residue of the product remains classified a
hazardous waste as per 40 CFR 261, Subpart C. State or local
regulations may also apply if they differ from the federal regulation.

D001, Ignitable Hazardous Waste

SECTION 14: TRANSPORTATION INFORMATION

Xylenes
3
UN 1307
III
N/A
Dangerous goods descriptions, (if indicated
above), may not reflect package size, quantity,
end-use or region-specific exceptions that can
be applied. Consult shipping documents for
descriptions that are specific to the shipment.

GAF SDS # 2029

Page 8 of 8
SECTION 15: REGULATORY INFORMATION

This product and its components are listed on the TSCA 8(b)
inventory.

N/A

Fire hazard, acute health hazard, chronic health hazard
Xylene 1330-20-7 77%
Ethyl Benzene 100-41-4 22%

This product contains a chemical known to the state of California to
cause cancer and birth defects, or other reproductive harm.

Other state regulations may apply. Check individual state requirements. The following components appear on
one or more of the following state hazardous substances list:

Chemical Name

CAS # CA MA MN PA NJ RI

SECTION 16: OTHER INFORMATION

N/A
September 2013
Headquarters Address Change

This information relates to the specific material designated and may not be valid for such material used
on combination with any other materials or in any process. Such information is to the best of our
knowledge and belief accurate and reliable as of the date compiled. However, no representation,
warranty or guarantee, expressed or implied, is made as to its accuracy, reliability, or completeness. It
is the user’s responsibility to satisfy himself as to the suitability and completeness of such information
for his particular use. We do not accept liability for any loss or damage that may occur from the use of
this information. Nothing herein shall be construed as a recommendation for uses which infringe valid
patents or as extending a license of valid patents.

GAF
Safety Data Sheet
SDS # 1079C
_________________________________________________________________________

Page 1 of 13

SECTION 1: PRODUCT AND COMPANY INFORMATION

EverGuard® 1121 TPO Bonding Adhesive
N/A

N/A
GAF
1 Campus Drive, Parsippany, NJ 07054
PHONE: (CHEMTREC) 800–424–9300
INFORMATION ONLY:

PREPARED BY:

APPROVED BY:

SECTION 2: HAZARD IDENTIFICATION

NFPA and HMIS RATINGS:

Rating

Rating

2 Health
Flammable Flammable
Reactive Reactive
Special Hazards - Personal Protection X

GAF SDS # 1079C

Page 2 of 13

GHS LABEL ELEMENTS:

GHS CLASSIFICATION: Flammable Liquid - Category 2
Eye Irritant - Category 2A
Skin Irritant - Category 2
Acute Toxicity - Category 4
Target Organ (SE) - Category 3
Target Organ (RE) - Category 2
Reproductive Toxicity - Category 2

ADDITIONAL HAZARD IDENTIFICATION INFORMATION:

Inhalation, Skin absorption, Skin contact, Eye contact, Ingestion

Can cause eye irritation. Symptoms include stinging, tearing,
redness, and swelling of eyes.
Skin:

May cause mild skin irritation. Prolonged or repeated contact may
dry the skin. Symptoms may include redness, burning, drying and

GHS PICTOGRAMS:

SIGNAL WORD:

Danger

HAZARD
STATEMENTS:

PRECAUTIONARY
STATEMENTS:

Highly flammable liquid and vapor.
Causes skin irritation.
Causes serious eye irritation.
May cause drowsiness or dizziness.
Suspected of damaging fertility or the unborn child.
May cause damage to organs (Neurologic: other (neuropsycho
vision)) through prolonged or repeated exposure if inhaled.

Do not handle until all safety precautions have been read and understood.
Keep away from heat/sparks/open flames/hot surfaces. No smoking.
Keep container tightly closed.
Ground/bond container and receiving equipment.
Use explosion-proof electrical/ ventilating/ lighting/ equipment.
Use only non-sparking tools.
Take precautionary measures against static discharge.
Do not breathe dust/ fume/ gas/ mist/ vapors/ spray.
Wash skin thoroughly after handling.
Do not eat, drink or smoke when using this product.
Use only outdoors or in a well-ventilated area.
GAF SDS # 1079C

Page 3 of 13

body through the skin is possible, but it is unlikely that this would
result in harmful effects during safe handling and use.
Ingestion:

Swallowing this material is harmful. This material can get into the
lungs during swallowing or vomiting. This can cause lung
inflammation and other lung injury.
Inhalation:

Breathing small amounts of this material during normal handling is
not likely to cause harmful effects. Breathing large amounts may be
harmful.
ACUTE HEALTH HAZARDS:

Inhalation of high concentrations of this material, as could occur in
enclosed spaces or during deliberate abuse, may be associated with
cardiac arrhythmias. Sympathomimetic drugs may initiate cardiac
arrhythmias in persons exposed to this material. This material (or a
component) has produced hyperglycemia and ketosis following
substantial ingestion.

Signs and symptoms of exposure to this material through breathing,
swallowing, and/or passage of the material through the skin may
include: stomach or intestinal upset (nausea, vomiting, diarrhea)
irritation (nose, throat, airways) temporary changes in mood and
behavior confusion irregular heartbeat.
Causes skin irritation. Causes serious eye irritation. May cause
drowsiness or dizziness. Suspected of damaging fertility or the
unborn child. Causes damage to organs through prolonged or
repeated exposure if inhaled.
CHRONIC HEALTH HAZARDS:

This material (or a component) shortens the time of onset or worsens
the liver and kidney damage induced by other chemicals. Prolonged
and repeated exposure to n-hexane may cause peripheral
neuropathy by damaging peripheral nerve tissue (that of the arms
and legs) and result in muscular weakness and loss of sensation.
Prolonged and repeated inhalation of high levels of mixed isomers of
hexane resulted in kidney damage in male rats. The effects
observed are the same as those seen in male rats exposed to other
hydrocarbons. The mechanism by which these chemicals cause the
characteristic kidney toxicity is unique to the male rat and the kidney
effects are not expected to occur in man. Prolonged intentional
toluene abuse may lead to damage to many organ systems having
effects on: central and peripheral nervous systems, vision, hearing,
liver, kidneys, heart and blood. Such abuse has been associated
with brain damage characterized by disturbances in gait, personality
changes and loss of memory. Comparable central nervous system
effects have not been shown to result from occupational exposure to
toluene. Prolonged intentional toluene abuse may lead to hearing
loss progressing to deafness. In addition, while noise is known to
cause hearing loss in humans, it has been suggested that workers
GAF SDS # 1079C

Page 4 of 13

suffer greater hearing loss than would be expected from exposure to
noise alone. Overexposure to this material (or its components) has
been suggested as a cause of the following effects in laboratory
animals: mild, reversible liver effects, mild, reversible kidney effects,
blood abnormalities, liver abnormalities, nasal damage, respiratory
tract damage (nose, throat, and airways), spleen damage, eye
damage, kidney damage, effects on hearing, testis damage, lung
damage, central nervous system damage, Overexposure to this
material (or its components) has been suggested as a cause of the
following effects in humans: liver abnormalities, visual impairment,
kidney damage and central nervous system effects
CARCINOGENICITY:

Based on the available information, this material cannot be classified
with regard to carcinogenicity. This material is not listed as a
carcinogen by the International Agency for Research on Cancer
(IARC), the National Toxicology Program (NTP), or the Occupational
Safety and Health Administration (OSHA).

SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS

Toluene

108-88-3 30 – 40 200 ppm
300 ppm – ceiling

(Petroleum), Light
Aliphatic

300 ppm

96-14-0

1.5 – 5
1000 ppm - STEL 510 ppm - Ceiling
96-37-7

NE = Not Established

GAF SDS # 1079C

Page 5 of 13

SECTION 4: FIRST AID MEASURES

If symptoms develop, immediately move individual away from exposure
and into fresh air. Flush eyes gently with water for at least 15 minutes
while holding eyelids apart; seek immediate medical attention.
SKIN:

Remove contaminated clothing. Wash exposed area with soap and
water. If symptoms persist, seek medical attention. Launder clothing
before reuse.
INHALATION:

If symptoms develop, move individual away from exposure and into fresh
air. If symptoms persist, seek medical attention. If breathing is difficult,
administer oxygen. Keep person warm and quiet; seek immediate
medical attention.
INGESTION:

Seek medical attention. If individual is drowsy or unconscious, do not
give anything by mouth; place individual on the left side with the head
down. Contact a physician, medical facility, or poison control center for
advice about whether to induce vomiting. If possible, do not leave
individual unattended.
NOTES TO PHYSICIANS OR
FIRST AID PROVIDERS:

Inhalation of high concentrations of this material, as could occur in
enclosed spaces or during deliberate abuse, may be associated with
cardiac arrhythmias. Sympathomimetic drugs may initiate cardiac
arrhythmias in persons exposed to this material. This material is an
aspiration hazard. Potential danger from aspiration must be weighed
against possible oral toxicity (see Section 11 – Toxicological Information)
when deciding whether to induce vomiting. This material (or a
component) has produced hyperglycemia and ketosis following
substantial ingestion.

SECTION 5: FIRE FIGHTING PROCEDURES

Water spray, dry powder, foam, carbon dioxide (CO2).

Carbon dioxide and carbon monoxide, phenols, various
hydrocarbons.
RECOMMENDED FIRE FIGHTING
PROCEDURES:

Material is volatile and readily gives off vapors which may
travel along the ground or be moved by ventilation and ignited
by pilot lights, flames, sparks, heaters, smoking, electric
GAF SDS # 1079C

Page 6 of 13

near the material handling point. Never use welding or cutting
torch on or near drum (even empty) because product (even
just residue) can ignite explosively. Wear full firefighting turn-
out gear (full Bunker gear), and respiratory protection (SCBA).
UNUSUAL FIRE & EXPLOSION
HAZARDS:
None.

SECTION 6: ACCIDENTAL RELEASE MEASURES

For personal protection see section 8. Eliminate all ignition
sources (flames including pilot lights, electrical sparks). Persons
not wearing protective equipment should be excluded from area of
spill until clean-up has been completed. Stop spill at source.
Prevent from entering drains, sewers, streams or other bodies of
water. Prevent from spreading. If runoff occurs, notify authorities
as required. Pump or vacuum transfer spilled product to clean
containers for recovery. Absorb unrecoverable product. Transfer
contaminated absorbent, soil and other materials to containers for
disposal.

SECTION 7: HANDLING AND STORAGE

Containers of this material may be hazardous when emptied.
Since emptied containers retain product residues (vapor, liquid,
and/or solid), all hazard precautions given in the data sheet must
be observed. Static ignition hazard can result from handling and
use. Electrically bond and ground all containers, personnel and
equipment before transfer or use of material. Special precautions
may be necessary to dissipate static electricity for non-conductive
containers. Use proper bonding and grounding during product
transfer as described in National Fire Protection Association
document NFPA 77.

OTHER PRECAUTIONS:

Store in closed containers in a dry, well-ventilated area. Containers
which are opened must be carefully resealed and kept upright to
prevent leakage. Observe label precautions.

GAF SDS # 1079C

Page 7 of 13

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

VENTILATION:
Provide sufficient mechanical (general and/or local exhaust)
ventilation to maintain exposure below TLV(s).
RESPIRATORY PROTECTION:

If workplace exposure limit(s) of product or any component is
exceeded (see exposure guidelines), a NIOSH-approved air
supplied respirator is advised in absence of proper environmental
control. OSHA regulations also permit other NIOSH respirators
(negative pressure type) under specified conditions (see your
industrial hygienist). Engineering or administrative controls should
be implemented to reduce exposure.
EYE PROTECTION:

SKIN PROTECTION:

Wear chemical resistant gloves. To prevent repeated or prolonged
skin contact, wear impervious clothing and boots.
OTHER PROTECTIVE EQUIPMENT:

WORK HYGIENIC PRACTICES:

Wash exposed skin prior to eating, drinking or smoking and at the
end of each shift.
EXPOSURE GUIDELINES:

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Liquid with a solvent odor.
<0 °F / -18 °C No data
Seta closed cup No data
No data No data
No data No data

No data 0.873 g/cm3 @
77 °F / 25 °C
7.3 lb/gal @ 77
VAPOR DENSITY:

PERCENT VOLATILE:
GAF SDS # 1079C

Page 8 of 13

VAPOR PRESSURE:

307.96 hPa @ 77
°F / 25 °C
MOLECULAR WEIGHT:

No data
No data No data

SECTION 10: STABILITY AND REACTIVITY

None known.

AVOID):
Acids, strong alkalis, strong mineral acids, strong oxidizing
agents.

HAZARDOUS DECOMPOSITION OR BY-
PRODUCTS:
Carbon dioxide and carbon monoxide, phenols, various
hydrocarbons.
HAZARDOUS POLYMERIZATION:

_________________________________________________________________________________________
SECTION 11: TOXICOLOGICAL INFORMATION

TOLUENE:
Acute oral toxicity: LD50 (Rat, male): 5,580 mg/kg

Acute inhalation toxicity: LC50 (Rat): 28.1 mg/l
Exposure time: 4 h
Test atmosphere: vapor
Method: OECD Test Guideline 403

Acute dermal toxicity: LD50 (Rabbit): 12,267 mg/kg

ACETONE:
Acute oral toxicity: LD50 (Rat, female): 5,800 mg/kg

Acute inhalation toxicity: LC50 (Rat, female): 76 mg/l
Exposure time: 4 h
Test atmosphere: vapor

Acute dermal toxicity: LD50 (Rabbit): > 7,426 mg/kg
GAF SDS # 1079C

Page 9 of 13

N-HEXANE:
Acute oral toxicity: LD50 (Rat, male and female): ca. 16 g/kg

Acute inhalation toxicity: LC50 (Rat, male): > 5000 ppm
Exposure time: 24 h
Test atmosphere: vapor

Acute dermal toxicity: LD50 (Rabbit, male and female): > 2,000 mg/kg
Assessment: No adverse effect has been observed in acute dermal toxicity
tests.

SOLVENT NAPHTHA (PETROLEUM), LIGHT ALIPHATIC:
Acute oral toxicity: LD50 (Rat): > 8,000 mg/kg

Acute inhalation toxicity: LC50 (Rat): > 7,630 mg/m3
Exposure time: 4 h
Test atmosphere: vapor
Method: OECD Test Guideline 403
Assessment: No adverse effect has been observed in acute inhalation toxicity
tests.

Acute dermal toxicity: LD50 (Rat): > 4,000 mg/kg
Assessment: Not classified as acutely toxic by dermal absorption under GHS.

METHYL-3-PENTANE:
Acute oral toxicity: LD50 (Rat): 16,000 mg/kg
Remarks: Information given is based on data obtained from similar substances.

Acute inhalation toxicity: LC50 (Rat): 73680 ppm
Exposure time: 4 h
Test atmosphere: vapour
Remarks: Information given is based on data obtained from similar substances.

Acute dermal toxicity: LD50 (Rabbit): 3,350 mg/kg
Assessment: No adverse effect has been observed in acute dermal toxicity
tests.
Remarks: Information given is based on data obtained from similar substances.

METHYLCYCLOPENTANE:
Acute oral toxicity: LD50 (Rat): > 2,000 mg/kg

Skin corrosion/irritation
Causes skin irritation.

Product:
Remarks: May cause skin irritation and/or dermatitis.
GAF SDS # 1079C

Page 10 of 13

Result: Repeated exposure may cause skin dryness or cracking.

Further information
Product:
nausea and vomiting., Concentrations substantially above the TLV value may cause

SECTION 12: ECOLOGICAL INFORMATION

An environmental hazard cannot be excluded in the event of unprofessional handling or
disposal., Toxic to aquatic life., Harmful to aquatic life with long lasting effects.

_________________________________________________________________________________________
SECTION 13: DISPOSAL CONSIDERATIONS

METHOD:
Dispose of in accordance with all applicable local, state and federal regulations.

Contaminated
packaging:
Empty remaining contents.
Dispose of as unused product.
Empty containers should be taken to an approved waste
handling site for recycling or disposal.
Do not re-use empty containers.

SECTION 14: TRANSPORTATION INFORMATION

Adhesives
3
ID NUMBER:

PACKING GROUP:

GAF SDS # 1079C

Page 11 of 13

LABEL STATEMENT:

N/A

OTHER:

N/A
IATA

PROPER SHIPPING NAME:

Adhesive
HAZARD CLASS:

3
ID NUMBER:

UN1133
PACKING GROUP:

II
LABEL STATEMENT:

N/A
OTHER:

N/A
IMDG

PROPER SHIPPING NAME:

Adhesive
HAZARD CLASS:

3
ID NUMBER:

UN1133
PACKING GROUP:

II
LABEL STATEMENT:

N/A
OTHER:

EMS: FE,SE

SECTION 15: REGULATORY INFORMATION

All components are listed on the TSCA inventory.

CERCLA Hazardous Substances (40 CFR 302)

Reportable Quantity – Components

GAF SDS # 1079C

Page 12 of 13

Acetone: 67-64-1, 5000 lbs
n-Hexane: 110-54-3, 5000 lbs
Cyclohexane: 110-82-7, 1000 lbs

SARA:

311/312 HAZARD CATEGORIES:

313 REPORTABLE INGREDIENTS:

Toluene 108-88-3
n-Hexane 110-54-3
Cyclohexane 110-82-7

CALIFORNIA PROPOSITION 65:

This product contains toluene, a chemical known to the state of
California to cause birth defects, or other reproductive harm.

Other state regulations may apply. Check individual state requirements. The following components appear on
one or more of the following state hazardous substances lists:

Chemical Name

CAS # CA MA MN NJ PA RI

Light Aliphatic

SECTION 16: OTHER INFORMATION

None
December 2014
Updates to Sections 2, 3., 9 and 11.
GAF SDS # 1079C

Page 13 of 13

This information relates to the specific material designated and may not be valid for such material used
on combination with any other materials or in any process. Such information is to the best of our
knowledge and belief accurate and reliable as of the date compiled. However, no representation,
warranty or guarantee, expressed or implied, is made as to its accuracy, reliability, or completeness. It
is the user’s responsibility to satisfy himself as to the suitability and completeness of such information
for his particular use. We do not accept liability for any loss or damage that may occur from the use of
this information. Nothing herein shall be construed as a recommendation for uses which infringe valid
patents or as extending a license of valid patents.

Appendix H

DEQ Risk Calculators

Version Date:
Basis:
Site Name:
Site Address:
DEQ Section:
Site ID:
Exposure Unit ID:
Submittal Date:
Reviewed By:
Worst Case Indoor Air and Sub Slab (Area C & D)
North Carolina Department of Environmental Quality
Risk Calculator
Battery & Ignition Distribution (Ello House)
Tryclan Drive and Ellenwood Place, Charlotte, NC
Brownfields Redevelopment Section
23055-19-060
February 2024
November 2023 EPA RSL Table
Prepared By:Hart & Hickman, PC
Hart & Hickman, PC
North Carolina DEQ Risk Calculator
Table of Contents
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
Form No.
Input Form 1A Complete Exposure Pathways
Input Form 1B Exposure Factors and Target Risks
Input Form 1C Contaminant Migration Parameters
Input Form 1D Sample Statistics
Input Form 2A Soil Exposure Point Concentration Table
Input Form 2B Groundwater Exposure Point Concentration Table
Input Form 2C Surface Water Exposure Point Concentration Table
Input Form 2D Soil Gas Exposure Point Concentration Table
Input Form 2E Indoor Air Exposure Point Concentration Table
Output Form 1A Risk for Individual Pathways
Output Form 1B Sitewide Risk
Output Form 2A Resident Soil
Output Form 2B Resident Groundwater Use
Output Form 2C Non-Residential Worker Soil
Output Form 2D Non-Residential Worker Groundwater Use
Output Form 2E Construction Worker Soil
Output Form 2F Recreator/Trespasser Soil
Output Form 2G Recreator/Trespasser Surface Water
Output Form 3A Resident Groundwater to Indoor Air
Output Form 3B Resident Soil Gas to Indoor Air
Output Form 3C Resident Indoor Air
Output Form 3D Non-Residential Worker Groundwater to Indoor Air
Output Form 3E Non-Residential Worker Soil Gas to Indoor Air
Output Form 3F Non-Residential Worker Indoor Air
Output Form 4A Soil to Groundwater - Forward Mode
Output Form 4B Groundwater to Groundwater - Forward Mode
Output Form 4C Soil to Surface Water - Forward Mode
Output Form 4D Groundwater to Surface Water - Forward Mode
Output Form 4E Soil to Groundwater - Backward Mode
Output Form 4F Groundwater to Groundwater - Backward Mode
Output Form 4G Soil to Surface Water - Backward Mode
Output Form 4H Groundwater to Surface Water - Backward Mode
Output Section 4 - Contaminant Migration Worksheets
Output Section 3 - Vapor Intrusion Calculators
TOC
Description
DATA INPUT SHEETS
Check box
if included
Input Section 1 - Exposure Pathways & Parameters
Input Section 2 - Exposure Point Concentrations
DATA OUTPUT SHEETS
Output Section 1 - Summary Output for All Calculators
Output Section 2 - Direct Contact Soil and Groundwater Calculators
North Carolina DEQ Risk Calculator
Exposure Point Concentrations
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
Description of Exposure Point Concentration Selection:
Exposure Point
Concentration
(ug/m3)
Notes: CAS Number Chemical
Minimum
Concentration
(Qualifier)
Maximum
Concentration
(Qualifier)
Units
Location of
Maximum
Concentration
Detection
Frequency
Range of
Detection
Limits
Concentration
Used for
Screening
Background
Value
Screening
Toxicity Value
(Screening
Level) (n/c)
Potential
ARAR/TBC
Value
Potential
ARAR/TBC
Source
COPC Flag
(Y/N)
Rationale for
Selection or
Deletion
17400 MP-3 67-64-1 Acetone ug/m3
2.47 MP-5 71-43-2 Benzene ug/m3
0.747 J flag, MP-5 75-15-0 Carbon Disulfide ug/m3
0.522 J flag, MP-5 67-66-3 Chloroform ug/m3
28.7 J flag, MP-3 110-82-7 Cyclohexane ug/m3
2.9 MP-DUP 75-71-8 Dichlorodifluoromethane ug/m3
1.44 J flag, MP-5 100-41-4 Ethylbenzene ug/m3
14200 MP-3 109-99-9 ~Tetrahydrofuran ug/m3
0.401 J flag, MP-5 142-82-5 Heptane, N-ug/m3
1.42 J flag, MP-5 110-54-3 Hexane, N-ug/m3
55.1 J flag, MP-3 67-63-0 Isopropanol ug/m3
79 MP-DUP 78-93-3 Methyl Ethyl Ketone (2-Butanone)ug/m3
12.4 J flag, MP-3 75-09-2 Methylene Chloride ug/m3
0.56 J flag, MP-DUP 91-20-3 ~Naphthalene ug/m3
4.59 MP-5/MP-DUP 115-07-1 Propylene ug/m3
0.379 J flag, MP-5/MP-DUP 100-42-5 Styrene ug/m3
3.34 MP-5 108-88-3 Toluene ug/m3
0.643 J flag, MP-DUP 76-13-1 Trichloro-1,2,2-trifluoroethane, 1,1,2-ug/m3
1.8 J flag, MP-5 75-69-4 Trichlorofluoromethane ug/m3
1.85 J flag, MP-5 95-63-6 Trimethylbenzene, 1,2,4-ug/m3
0.565 J flag, MP-5 108-67-8 Trimethylbenzene, 1,3,5-ug/m3
8.26 J flag, MP-5 1330-20-7 Xylenes ug/m3
Input Form 2D
Soil Gas Exposure Point Concentration Table
Note: Chemicals highlighted in orange are non-volatile chemicals. Since these chemicals do not pose a vapor intrusion risk, no risk values are calculated for these chemicals.
If the chemical list is changed from a prior calculator run, remember to select "See All Chemicals" on the data output sheet or newly added chemicals will not be included in risk calculations
North Carolina DEQ Risk Calculator
Exposure Point Concentrations
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
Description of Exposure Point Concentration Selection:
Exposure Point
Concentration
(ug/m3)
Notes: CAS Number Chemical
Minimum
Concentration
(Qualifier)
Maximum
Concentration
(Qualifier)
Units
Location of
Maximum
Concentration
Detection
Frequency
Range of
Detection
Limits
Concentration
Used for
Screening
Background
Value
Screening
Toxicity Value
(Screening
Level) (n/c)
Potential
ARAR/TBC
Value
Potential
ARAR/TBC
Source
COPC Flag
(Y/N)
Rationale for
Selection or
Deletion
263 D-IAS-1 67-64-1 Acetone ug/m3
2.29 IAS-DUP 71-43-2 Benzene ug/m3
0.972 J flag, D-IAS-1 74-87-3 Chloromethane ug/m3
2.89 IAS-DUP 75-71-8 Dichlorodifluoromethane ug/m3
3.23 C-IAS-1 100-41-4 Ethylbenzene ug/m3
25.6 IAS-DUP 109-99-9 ~Tetrahydrofuran ug/m3
2.41 IAS-DUP 142-82-5 Heptane, N-ug/m3
2.58 IAS-DUP 110-54-3 Hexane, N-ug/m3
9.13 B flag, D-IAS-1 67-63-0 Isopropanol ug/m3
65.8 IAS-DUP 78-93-3 Methyl Ethyl Ketone (2-Butanone)ug/m3
1.63 J flag, D-IAS-1 75-09-2 Methylene Chloride ug/m3
0.571 J flag, C-IAS-1 91-20-3 ~Naphthalene ug/m3
2.14 IAS-DUP 100-42-5 Styrene ug/m3
11.4 IAS-DUP 108-88-3 Toluene ug/m3
0.59 J flag, C-IAS-1 76-13-1 Trichloro-1,2,2-trifluoroethane, 1,1,2-ug/m3
1.74 J flag, IAS-DUP 75-69-4 Trichlorofluoromethane ug/m3
10.3 C-IAS-1 95-63-6 Trimethylbenzene, 1,2,4-ug/m3
2.77 IAS-DUP 108-67-8 Trimethylbenzene, 1,3,5-ug/m3
23.9 IAS-DUP 1330-20-7 Xylenes ug/m3
Input Form 2E
Indoor Air Exposure Point Concentration Table
Note: Chemicals highlighted in orange are non-volatile chemicals. Risks are calculated for these chemicals if indoor air concentrations are entered and indoor air screening levels have been established, but it should be noted that detections of these chemicals are likely not associated with vapor intrusion.
If the chemical list is changed from a prior calculator run, remember to select "See All Chemicals" on the data output sheet or newly added chemicals will not be included in risk calculations
North Carolina DEQ Risk Calculator
Risk for Individual Pathways Output Form 1A
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
Receptor Pathway Carcinogenic
Ris Hazard Index Risk exceeded?
Soil NC NC NC
Groundwater Use* NC NC NC
Soil NC NC NC
Groundwater Use* NC NC NC
Construction Worker Soil NC NC NC
Soil NC NC NC
Surface Water* NC NC NC
Receptor Pathway Carcinogenic
Ris Hazard Index Risk exceeded?
Groundwater to Indoor Air NC NC NC
Soil Gas to Indoor Air 5.8E-07 2.3E-01 NO
Indoor Air 1.6E-05 8.2E-01 NO
Groundwater to Indoor Air NC NC NC
Soil Gas to Indoor Air NC NC NC
Indoor Air NC NC NC
Pathway Source
Source Soil NC
Source Groundwater NC
Source Soil NC
Source Groundwater NC
Groundwater Exceedence of 2L at Receptor?
Exceedence of 2L at Receptor?
1. If lead concentrations were entered in the exposure point concentration tables, see the individual calculator sheets for lead
concentrations in comparison to screening levels. Note that lead is not included in cumulative risk calculations.
Notes:
3. NM = Not modeled, user did not check this pathway as complete.
4. NC = Pathway not calculated, required contaminant migration parameters were not entered.
DIRECT CONTACT SOIL AND WATER CALCULATORS
Resident
Non-Residential Worker
Recreator/Trespasser
2. * = If concentrations in groundwater exceed the NC 2L Standards or IMAC, or concentrations in surface water exceed the
NC 2B Standards, appropriate remediation and/or institutional control measures will be necessary to be eligible for a risk-based
closure.
Surface Water Exceedence of 2B at Receptor?
Exceedence of 2B at Receptor?
VAPOR INTRUSION CALCULATORS
Resident
Non-Residential Worker
CONTAMINANT MIGRATION CALCULATORS
Target Receptor Concentrations Exceeded?
North Carolina DEQ Risk Calculator
DEQ Risk Calculator - Vapor Intrusion - Resident Soil Gas to Indoor Air
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
CAS # Chemical Name:
Soil Gas
Concentration
(ug/m3)
Calculated
Indoor Air
Concentration
(ug/m3)
Target Indoor
Air Conc. for
Carcinogens @
TCR = 1E-06
Target Indoor Air
Conc. for Non-
Carcinogens @
THQ = 0.2
Calculated
Carcinogenic
Risk
Calculated
Non-
Carcinogenic
Hazard
Quotient
67-64-1 Acetone 17400 522 - -
71-43-2 Benzene 2.47 0.0741 3.6E-01 6.3E+00 2.1E-07 2.4E-03
75-15-0 Carbon Disulfide 0.747 0.02241 - 1.5E+02 3.1E-05
67-66-3 Chloroform 0.522 0.01566 1.2E-01 2.0E+01 1.3E-07 1.5E-04
110-82-7 Cyclohexane 28.7 0.861 - 1.3E+03 1.4E-04
75-71-8 Dichlorodifluoromethane 2.9 0.087 - 2.1E+01 8.3E-04
100-41-4 Ethylbenzene 1.44 0.0432 1.1E+00 2.1E+02 3.8E-08 4.1E-05
109-99-9 ~Tetrahydrofuran 14200 426 - 4.2E+02 2.0E-01
142-82-5 Heptane, N- 0.401 0.01203 - 8.3E+01 2.9E-05
110-54-3 Hexane, N- 1.42 0.0426 - 1.5E+02 5.8E-05
67-63-0 Isopropanol 55.1 1.653 - 4.2E+01 7.9E-03
78-93-3 Methyl Ethyl Ketone (2-Butanone) 79 2.37 - 1.0E+03 4.5E-04
75-09-2 Methylene Chloride 12.4 0.372 1.0E+02 1.3E+02 3.7E-09 5.9E-04
91-20-3 ~Naphthalene 0.56 0.0168 8.3E-02 6.3E-01 2.0E-07 5.4E-03
115-07-1 Propylene 4.59 0.1377 - 6.3E+02 4.4E-05
100-42-5 Styrene 0.379 0.01137 - 2.1E+02 1.1E-05
108-88-3 Toluene 3.34 0.1002 - 1.0E+03 1.9E-05
76-13-1 Trichloro-1,2,2-trifluoroethane, 1,1,2- 0.643 0.01929 - 1.0E+03 3.7E-06
75-69-4 Trichlorofluoromethane 1.8 0.054 - -
95-63-6 Trimethylbenzene, 1,2,4- 1.85 0.0555 - 1.3E+01 8.9E-04
108-67-8 Trimethylbenzene, 1,3,5- 0.565 0.01695 - 1.3E+01 2.7E-04
1330-20-7 Xylenes 8.26 0.2478 - 2.1E+01 2.4E-03
Cumulative: 5.8E-07 2.3E-01
All concentrations are in ug/m3
Output Form 3B
Carcinogenic risk and hazard quotient cells highlighted in orange are associated with non-volatile chemicals. Since these chemicals do not pose a vapor intrusion
risk, no risk values are calculated for these chemicals.
North Carolina DEQ Risk Calculator
DEQ Risk Calculator - Vapor Intrusion - Resident Indoor Air
Version Date: February 2024
Basis: November 2023 EPA RSL Table
Site ID: 23055-19-060
Exposure Unit ID: Worst Case Indoor Air and Sub Slab (Area C & D)
CAS # Chemical Name:
Indoor Air
Concentration
(ug/m3)
Target Indoor
Air Conc. for
Carcinogens @
TCR = 1E-06
Target Indoor Air
Conc. for Non-
Carcinogens @
THQ = 0.2
Calculated
Carcinogenic
Risk
Calculated
Non-
Carcinogenic
Hazard
Quotient
67-64-1 Acetone 263 - -
71-43-2 Benzene 2.29 3.6E-01 6.3E+00 6.4E-06 7.3E-02
74-87-3 Chloromethane 0.972 - 1.9E+01 1.0E-02
75-71-8 Dichlorodifluoromethane 2.89 - 2.1E+01 2.8E-02
100-41-4 Ethylbenzene 3.23 1.1E+00 2.1E+02 2.9E-06 3.1E-03
109-99-9 ~Tetrahydrofuran 25.6 - 4.2E+02 1.2E-02
142-82-5 Heptane, N- 2.41 - 8.3E+01 5.8E-03
110-54-3 Hexane, N- 2.58 - 1.5E+02 3.5E-03
67-63-0 Isopropanol 9.13 - 4.2E+01 4.4E-02
78-93-3 Methyl Ethyl Ketone (2-Butanone) 65.8 - 1.0E+03 1.3E-02
75-09-2 Methylene Chloride 1.63 1.0E+02 1.3E+02 1.6E-08 2.6E-03
91-20-3 ~Naphthalene 0.571 8.3E-02 6.3E-01 6.9E-06 1.8E-01
100-42-5 Styrene 2.14 - 2.1E+02 2.1E-03
108-88-3 Toluene 11.4 - 1.0E+03 2.2E-03
76-13-1 Trichloro-1,2,2-trifluoroethane, 1,1,2- 0.59 - 1.0E+03 1.1E-04
75-69-4 Trichlorofluoromethane 1.74 - -
95-63-6 Trimethylbenzene, 1,2,4- 10.3 - 1.3E+01 1.6E-01
108-67-8 Trimethylbenzene, 1,3,5- 2.77 - 1.3E+01 4.4E-02
1330-20-7 Xylenes 23.9 - 2.1E+01 2.3E-01
Cumulative: 1.6E-05 8.2E-01
All concentrations are in ug/m3
Output Form 3C
** - Note that the EPA has no consensus on reference dose or cancer slope factor values for lead, therefore it is not possible to calculate carcinogenic
risk or hazard quotient. Lead concentrations are compared to the National Ambient Air Quality Standard of 0.15 μg/m3.
Carcinogenic risk and hazard quotient cells highlighted in orange are associated with non-volatile chemicals. Risks are calculated for these values if
indoor air concentrations are entered and indoor air screening levels have been established, but it should be noted that detections of these chemicals
are likely not associated with vapor intrusion.
North Carolina DEQ Risk Calculator